RACK-210 CHASSIS USER`S MANUAL
Contents
1. pa A e T 23 55 mm Lo El TE 2 1 11 70mm 0 00 mm fi 0 00mm E E E E E E E E 8 a 8 8 EXPLODED DIAGRAM APPENDIX B N il2. RACK 210 CHASSIS USER S MANUAL Copyright Notice This document and product is copyrighted October 1998 by ICP Electronics Inc All rights are reserved No part of this manual may be reproduced copied or translated without prior notice to ICP Electronics Inc The information provided in this document is for reference only We do not assume any responsibility arising out of the application of the products This manual is subject to change without any notice RACK 210 ICP are trademark of ICP Electronics Inc Table of Contents Chapter 1 Product Information 1 1 General Information 1 2 Product Specifications 1 3 Dimensions Chapter 2 System Setup 2 1 Front Panel of RACK 210 2 2 Rear Panel of RACK 210 2 3 Removing the chassis cover 2 4 Backplane Installation 2 5 Disk Drives Installation 2 6 Replacing the Filter 2 7 Power Supply Installation 2 8 Fan Installation Appendix A Passive Backplane Appendix B Exploded Diagram Chapter 1 Product Information 1 1 General Information RACK 210 Wall mount IPC chassis is a rugged PC AT compatible computer designed for the factory floor and other Industrial harsh environment The RACK 210 features 5 slots Passive Backplanes and high reliability AC Input Power Supply ACE 920A 1 2 Product Specifications General specification Construction Heavy duty steel Disk Driver Supports one 3 5 FDD and one CD ROM two 3 5 HDD Cooling Fan One ball bearing fan for add
3. on cards cooling Indicator Two LEDs to monitor the status of HDD and Power Supply Dimension 431 x 477 2 x 88mm WxDxH Passive Backplanes Optional BP 5S 5 slot ISA bus Backplane PCI 5SD 5 slot ISA PCI bus Backplane PCI 6SR 6 slot ISA PCI bus Backplane Power Supply Standard equipped power supply for the RACK 210 is ACE 920A Working Environment Operating Temperature O 50 C Relative Humidity 5 95 Relative Vibration po 5 17Hz 0 1 double amplitude displacement 17 640Hz 1 5G acceleration peak to peak Shock 10G acceleration peak to peak Safety approval meet CE FCC Cooling Fan One ball bearing fan for add on cards cooling Drive Capacity Supports one 3 5 FDD and one CD ROM two 3 5 HDD 1 3 Dimensions 431 00mm 477 20mm 457 20mm 483 00mm 466 00mm 6 5x10 HOLE 3 ES Chapter 2 Installation Procedure The following set up procedures are provided to assist you in installing the system unit please follow the steps below 2 1 Front Panel of RACK 210 H D D LED POWER LED KEYBOARD POWER SWITCH 2 2 Rear Panel of RACK 210 AC OUTPUT AC INPUT 2 3 Removing the chassis cover The cover is mounted by four screws on the top of
4. the chassis remove them and slide the cover to the rear of the chassis Figure below shows how to remove the chassis cover 2 4 Backplane Installation the RACK 210 Figure below illustrates how to install the backplanes on 10 2 5 Disk Drives Installation 1 Remove the chassis top cover 2 Remove the disk drive bay 3 Attach the FDD to the bracket with four screws and connect FDD cable amp power cable to the FDD 4 Attach the HDD to the bracket with four screws and connect a 40 pin flat cable amp power cable to the HDD Step 1 12 2 6 Replacing the Filter The filter of the RACK 210 is located at the front end of the chassis Under continuous use the filter should be removed about once a mounth To replace the filter open and close the door by screws Take out the old filter and slide the new one into place Then close and lock the filter door 2 7 Power Supply Installation 13 ACE 920A POWER SUPPLY P8 P9 POWER SWITCH 2 7 Fan Installation 14 lt o a gt Lu O lt POWER SUPPLY GND BLACK ASS SOU SO 0 Za APPENDIX A PASSIVE BACKPLANES LEFT SIDE SI J E A Ou 1 D RIGHT SIDE 80 00 mm 73 05mm 7
Download Pdf Manuals
Related Search