XCarLink User Manual 2013
Contents
1. Interfaces designed for Audi VW Skoda and Seat have the ability to retain an existing factory fitted CD changer or external Single disk player See installation instructions The procedure for switching from the interface to your CD changer is while listening to audio via the interface toggle to FM radio usually by pressing the FM button and then back to CD changer mode CD Button On some models it may be necessary to disconnect the device connected Such as iPod or USB SD when switching to CD changer CONNECTING AN AUXILIARY DEVICE Any audio device can be connected to the Auxiliary port which is labelled Aux The device can be connected using an optional 3 5mm Aux input cable The display on the radio will change to CD8 88 Using this method it is not possible to control the Auxiliary device through the radio steering wheel buttons however the volume control can be adjusted All other controls would have to be performed directly via the device 13 NOTES e As the track number on the radio is limited to 2 digits the corresponding playlist track number is always truncated For example if the 157th song on the playlist is being played the display will be 57 ignoring the first digit e Functions such as Disk select seek Back Next Fast Forward FF Rewind RW may operate differently in different car models factory radios therefore the examples given above may not be accurate Please refer to your radios user manual f2. possible to where you would be speaking from such as the sun visor or top of the panel at the edge of the windscreen The microphone can be held in place with double sided tape if required 4 Power on the radio and ignition to ensure that the Bluetooth module is receiving power and ready to be paired with a mobile device see operating instructions OPERATING INSTRUCTIONS IPOD INTERFACE Before you begin please check that your iPod software is up to date This can be checked and upgraded if necessary via iTunes For further information please visit www apple com support We also recommend that playlists are setup on your iPod for easy navigation of music via your radio streering wheel controls GENERAL OPERATION Connect your iPod to the Xcarlink interface via the supplied cable power on the radio and switch to CD changer as the source it will then switch to your iPod and is now ready to use Xcarlink iPod interface has two operating modes 1 Manual Mode 2 Playlist Mode The Disk buttons on your factory radio allow you to switch between the above two modes Depending on the model of your radio the disk buttons could be represented by numbers 1 2 3 4 5 6 or on some models Disk are selected via the Disk Disk buttons Please refer to the user guide provided with your car radio for further information and to familiarise yourself with the functions of your particular radio and the procedure for disk selection Operatio
3. s in a changer for example if your radio can control a maximum of 6 Disks in a changer the number of playlists that it will control will be 5 Some factory radios have the capability to select up to 10 Disks representing 9 playlists During playlist mode the iPod will be locked and display the message Do not disconnect During playlist mode e The track timer on the radio would be accurate for each song e The repeat button can be used to repeat a song after if finishes playing e Fast Forward FF and Rewind RW buttons can be used to seek within a song and the track timer will be updated to reflect the current position within the song e The Random button can be used to select tracks in random order however if you then select the skip button to select a track it will no longer play tracks at random and instead will select the next track within the playlist If you are in random mode and would like to switch to another random track the random button should be selected twice e The information being displayed on the factory radio display represents the playlist number and the track within that particular playlist For example CD2 57 would indicate that it is playing the 57th song on the first playlist e The iPod iPhone will automatically pause and remember the last playing position when the ignition is turned off or when you switch to another source such as FM radio SWITCHING FROM XCARLINK TO A FACTORY FITTED CD CHANGER
4. FACES Interfaces designed for Audi radios with the 20 pin ISO connection Non Quadlock is supplied with a separate 20 pin adapter which needs to be connected as follows 1 Release the dark blue connector by pressing the clip at the bottom of the connector inwards 2 Attach the dark blue connector to the black male connector on the Xcarlink 3 Then attach the light blue female connector on the Xcarlink to the red and green connectors Y CONNECTION CABLES FOR TOYOTA AND HONDA If your existing CD changer port is already occupied this could be a connection for the radio controls Sat Nav or External Factory CD changer a Y connection cable would be required In which case remove the existing connection and plug the Female end of the Y cable into the CD changer port The Y cable branches out into two connections connect one end to the interface and the other to the existing connection Ray Connect to existing Connection A Connect to CD Changer port NISSAN CONNECTION Nissan interfaces have additional cables which need to be connected simply connect these cables as shown in the following diagram The BAT wire is live and must be connected to the power supply The ACC wire must be connected to the ignition live i e 12v when ignition has started Please refer to the wiring diagram for your radio which should be on the back of the unit to ensure that it is connected to the correct cables BMW CONNECTI
5. ON BMW interfaces also include 4 additional cables which should be connected as follows Gnu tb j Me Note If your BMW interface has a Plug and Play connector the above connection would not be required FINAL STEPS e Once the interface has been successfully connected to the radio route the cable to the desired location such as glovebox dashboard centre console armrest behind the radio etc e If you are installing an iPod interface connect the iPod cable with the round connector to the interface and route it to the appropriate location e Test the interface before you replace the factory radio Check that all connections at the back of the radio are firmly in place and your audio system is functioning correctly Once everything has been tested re fit your factory radio back to its original state BLUETOOTH MODULE OPTIONAL The optional Bluetooth module allows you to use the interface as a hans free car kit and for wirelessly streaming music to your car radio It can be paired with any Bluetooth mobile phone device for a complete in car integration solution The installation procedure is as follows 1 Connect the Bluetooth module to the Micro USB port on the interface 2 Route the Bluetooth module to the required location you may prefer to place the module within easy reach whilst driving so that the call answer button can be operated 3 Route the microphone cable so that the microphone is located as close as
6. TH MOBILE PHONE 1 Ensure that the ignition or radio is powered off before connecting the Bluetooth module See installation instructions above 2 The next step is to pair your mobile phone or device with the Bluetooth module This can be achieved by accessing the Bluetooth menu on your phone and activating search and discovery mode Refer to your mobile phones user guide for further information 3 When your phone displays the list of available Bluetooth devices select Xcarlink 4 When the phone asks for a pairing code enter 0000 and press Ok Connect The Bluetooth device is now paired with the Xcarlink Bluetooth module and you are ready to receive or make a call 17 NOTES e Most phones will automatically connect to the kit after pairing therefore the above procedure would only have to be carried out once Some phones may require manual connection after pairing e To pair with a new device simply hold down the BT button or Fast Forward FF button on some radios for 2 3 seconds then follow the pairing procedure above MAKING A CALL Dial the number on your phone or select a contact The sound will automatically be routed to your car audio system ANSWERING A CALL When a call is received you will hear a ringing tone via your car radio speakers The call can be answered in the following ways 1 By pressing the call answer reject button on the Bluetooth module 2 By pressing the Fast Forward FF button on some rad
7. USER MANUAL CONTENTS INSTALLATION IPOD AND USB INTERFACE BLUETOOTH MODULE OPTIONAL OPERATING INSTRUCTIONS IPOD INTERFACE USB SD INTERFACE BLUETOOTH MODULE OPTIONAL 10 11 14 17 INTRODUCTION Xcarlink iPod interface is a vehicle specific solution for connecting an iPod directly to the external CD changer port of a factory fitted OEM car radio The direct digital connection allows music on an iPod to be played through the car radio with no loss of sound quality whilst at the same time charging the iPod and allowing it to be controlled via the radio or steering wheel buttons The Xcarlink USB interface also connects directly to the CD changer port for digital sound quality but instead allows you to play and control music stored on a USB SD card via the steering factory radio or steering wheel buttons Both the USB and iPod interface can be used to connect any portable audio device via an Aux in connection This manual covers installation and operation of the Xcarlink iPod interface USB interface and Optional Bluetooth module Please refer to the instructions in relation to the product you have purchased The kit should include the following parts IPOD INTERFACE e Xcarlink iPod interface with vehicle specific CD changer connection e iPod connection Cable e User manual e Bluetooth module optional USB SD INTERFACE Xcarlink USB interface with vehicle specific CD Changer connection 3 5mm line in cable USB e
8. io models 3 Answering the call directly using your phone DURING A CALL e During a call the music playing on the iPod or USB interface will automatically interrupt and it will allow you to take the call Music will then continue to play from automatically after the call has ended e A call can be rejected by holding down the Bluetooth button for 3 seconds e Press the Bluetooth button or radio Fast Forward FF button on some radios to end the call A2 DP WIRELESS MUSIC STREAMING An A2DP compatible Bluetooth device can be used to wirelessly stream music to your car radio system via the Bluetooth module Select the song track that you would like to play on your mobile phone and then select the option to send via Bluetooth see your phones user guide for more information The call answer reject button can be used to pause stop play music WARRANTY The Xcarlink iPod and USB interface carries a one year limited warranty that protects against manufacturing defects We do not provide any warranty for installation If you experience a problem and require technical support please submit a ticket at www xcarlink co uk helpdesk and include your order number We are unable to provide support if the product was not purchased directly from us or one of our official dealers distributors DISCLAIMER All text and images contained within this manual are Copyright and any reproduction without our prior consent is strictly forbidden All photo
9. n on your radio is as follows CD Disk Button Operation Disk 1 Switch to Manual Mode Disk 2 Playlist 1 Disk 3 Playlist 2 Disk 4 Playlist 3 Disk 5 Playlist 4 Disk 6 Playlist 5 11 MANUAL MODE Whilst in Manual Mode Disk 1 your iPod controls and screen display will remain available as normal allowing you to select albums artists tracks etc all via your iPod iPhone Furthermore tracks can selected using the seek button on your radio or steering wheel controls The Fast Forward FF and Rewind RW buttons can also be used to seek within a track Manual mode is ideal if you require full access to your iPod without any restrictions Typical example would be to use your iPod to select an album and then use the seek buttons on your radio steering wheel to browse tracks within that particular album In manual mode the information being displayed on the car radio display would be irrelevant the track timer would not accurately reflect the position within a given song PLAYLIST MODE Select Disk 2 or via Disk to switch to playlist mode and will start playing the first playlist stored on your iPod In playlist mode each Disk from Disk 2 onwards represents a playlists on your iPod iPhone Selecting Disk 3 will select the 2nd Playlist Disk 4 the 3rd playlist etc The number of playlists that the factory radio can select is dependent on the way in which your radio has been designed to select CD
10. ng within the folder the radio display will show 57 ignoring the first digit The following should be avoided e long file names e file names with the characters e MP3s using different id3 tags keep them consistent CONNECTING AN AUXILIARY DEVICE e Any audio device can be connected to the Aux in port Firstly connect the Micro USB to 3 5mm cable to the Aux BT port and then connect your device to the 3 5mm connection The display on the radio will change to CD8 88 Using this method it is not possible to control the Auxiliary device through the radio steering wheel buttons however volume control can be adjusted All other controls would have to be performed directly via the device e If a USB SD card is already connected it will stop playing as soon as an Auxiliary device is connected OPERATING INSTRUCTIONS BLUETOOTH MODULE The Bluetooth module is an optional accessory which utilises the technology Within an Xcarlink iPod or USB interface to provide a hands free car kit solution which integrates with your car radio system It can also be used for wireless streaming of music from an audio device to your car Via AD2P stereo Bluetooth The Bluetooth module simply connects to the Micro USB connection on an Xcarlink iPod or USB interface It is plug and play operation with no additional installation required to your car audio system Light Call Answer Reject Button External Microphone s PAIRING WITH YOUR BLUETOO
11. ognise each folder as a Disk To select folders use the disk select buttons Disk 1 Disk 2 etc On some radios this is operated via the CD and CD buttons Once you have selected a folder use the seek button on the radio or steering wheel controls to change tracks within the folder Fast Forward FF and Rewind RW buttons can be used to seek within a song and the track timer will be updated to reflect the current position within the song The Random button can be used to select tracks in random order If you change tracks whilst in random mode the next track within the folder will be selected On some radios random tracks can be selected after you change tracks by pressing the random button twice once to cancel random mode and again to re select it wen Power Of Fae Na Tae Select Taack Scan uretonlFuncson 15 NOTES e The information being displayed on the factory radio display represents the folder number and the track within that particular folder For example CD1 02 would indicate that it is playing the second track within folder 1 Display may vary according to the radio model To manage the order in which tracks are played on your radio you may wish to download Play order manager which is available to download from www xcarlink co uk helpdesk select file Library to download e As the track number on the radio is limited to 2 digits the corresponding track number is always truncated For example if the 157th so
12. om the back of the radio The existing CD changer connection is then connected to the Male Black connector on the interface The Female Blue connector is then connected to the CD changer port where your original CD changer was previously connected On some models there may be two ports with a similar connection use the diagram located on the radio casing or the manufacturers documentation to ensure that the interface is connected to the CD changer port The Male Black connector is only used if you have an existing CD changer if there is no CD changer present the male cable connector is not required and should be left disconnected VAG VW Audi Seat and Skoda Ground Connection Interfaces for VAG vehicles need to be grounded in order for the interface to function correctly The interface provides two ground connections two black wires one with a larger ring connector and another with a smaller ring connector Connect at least one of the two ground connections to a suitable earthing point such as the metal body of your factory radio although It is recommended that both cables are connected for extra security Make sure that the ground cable s are connected securely as the interface will fail to operate without sufficient grounding Installation Example tu 8 Mini ISO Seat Skoda Volkswagen Audi 12 PIN Quadlock Seat Skoda Volkswagen CONNECTION OF THE AUDI 20 PIN ADAPTER FOR AUDI ISO INTER
13. or the exact operation e Text supported on some models OPERATING INSTRUCTIONS USB SD INTERFACE USING AN SD CARD OR USB DRIVE The USB interface has a built in high quality MP3 WMA encoder which allows you to play and control MP3 or WMA files from your factory car stereo The following procedure explains how to setup your SD card or USB drive e Firstly you would need to ensure that your USB drive or SD card is formatted to FAT32 and that all other files have been deleted e Create folders on your USB SD card in the root directory using the format CD01 CD02 CD03 etc The number of folders that the factory radio can select is limited only by the number of CD s that your factory radio has been designed to select within a CD changer for example if your radio can control a maximum of 6 Disks in a changer the number of folders that it will control will be 6 Some factory radios have the capability to select up to 10 folders juss sD Paco gt Fy cDo Eycpo2 m pi Evanescence Call Me When Your re Sober mp3 7 cD03 U2 Bono amp The Cors 2 When The Stars Go Blue mp3 ee C D 04 Natasha Bedingfield g Unwritten mp3 coos 7cD06 14 e Load MP3 or WMA files into each folder as required e Connect your USB drive or SD card to the interface and then power on the radio and switch to CD changer as the source it will then switch to your USB SD and is now ready to use You radio will now rec
14. s and instructions are for illustration purposes only and may differ from the actual fitting in your car We do not accept any liability for any damage including incidental consequential or indirect damages losses and will not be liable for any installation diagnostic fees incurred 2009 DIGIBUYS LTD ALL RIGHTS RESERVED XCARLINK THE LOGO DESIGN ARE TRADEMARKS OR REGISTERED TRADEMARKS OF DIGIBUYS LTD IPOD IS A TRADEMARK OF APPLE INC THE REPRODUCTION OF TEXT IMAGES DESIGN OR ANY CONTENT WITHIN THIS MANUAL FOR ANY PURPOSE WITHOUT OUR WRITTEN CONSENT IS STRICTLY FORBIDDEN
15. xtension cable User manual Bluetooth module optional INSTALLATION IPOD AND USB INTERFACE CONNECTING THE INTERFACE TO THE CD CHANGER PORT The first step is to remove your existing car radio depending on the radio model this would require the use of removal keys or removal of dashboard panels Removal of your factory radio should be carried out in accordance with the correct procedure for your particular car radio model you may be able to find more information via websites such as www fitaudio com or by contacting a dealer qualified installer Once the radio has been removed locate the CD changer port at the rear of the radio and then connect the Vehicle specific connector to it Please note that some models may require connection to the CD changer port via the vehicle harness The CD changer port on your radio should be easily identified and should match the connector supplied with the interface If you are in any doubt please refer to the manufacturers documentaion supplied with the radio It is important to ensure that the CD changer connection is pushed firmly in place so that it makes a good full connection with the CD changer port VAG VW Audi Seat Skoda With Existing CD Changer These interfaces are supplied with CD changer retention connections so you can continue to use an existing CD changer while the interface is connected On vehicles with an existing factory CD changer you would firstly need to remove CD changer fr
Download Pdf Manuals
Related Search