PJC211/212/221/222 S-linkControl Panel
Contents
1. When any thruster is running both PTO pumps will be active to ensure good performance When an SPS stabilizer system is active one PTO pump will be deactivated to save power If stabilizers are active and the system pressure drops below 80bar the system will activate the second PTO pump for 15 minutes to increase the flow capacity and maintain required pressure After 15 minutes the second pump will be deactivated unless the pressure is still below 80 bar Pump Control is set to Not Available when Thruster Stern is set to with Bypass Valve Pump Control will then not be able to edit NOTE Pump Control Auto must only be used on PHC 024 with firmware V 1 008 or higher 1 3 Cooling Pump Values Always Running Temp Controlled default When the option Temp Controlled is selected the cooling pump will start when oil temperature exceeds 50 C 122 F and stop when the oil temperature goes below 40 C 104 F On systems with two oil tanks this setting will apply to both tanks 1 4 Cooling Signal Output Values Normal default Inverted Set to Normal when using a hydraulic cooling pump Should be set to Inverted when using an electrical cooling pump with a 10 2380A 12 24V relay box 1 5 Cooling Power Save Values ON OFF default ON sets the Cooling Pump into power save mode which means the Cooling Pump output is dropping to 0 volt when the oil pressure is below 10 bar for more than 10 secon2. FW V1 012 or older and older and SR150000 FW V1 006 and older SR150000 FW V1 006 or older Controller Overtemp PPC800 temp has been over PPC800 cool down below 45 C 113 F 80 C 1 76 F Controller Overtemp SR150000 temp has been over SR150000 cool down below 45 C 113 F OGC o F Low Voltage Low voltage on Motor Recharge battery reset or device power OFF ON Thermoswitch Yes Motor temp has been over Motor cool down below 100 C 212 F Joe oF IPC Error Motor relay fault Turn off thruster battery main switch Thruster must be serviced by authorized personnel power OFF resets alarm 8 Critical Error PPC800 output fail PPC800 must be sent for service Motor Contactor No current on motor relay coil Check motor relay connections short circuit or relay dead System Error Fatal error Device must be serviced by authorized personnel No No communication with device Check S Link or power connections Communication Motor Temp Sensor Motor temperature sensor fail Check for an open circiut on the temp sensor on the motor or abnormal reading Fuse Blown Fuse blown Replace fuse or check if main cable from battery and main cable to thruster has been switched Manual Override Main switch manually overridden Pull main switch Motion IN Fault Retract obstructed while retracting Turn panel on and manually override main switch Remove obstruction and try again Motion OUT Fault Retract obstructed while deploying Tur
3. a dual stern thruster setup Runtime indicator will be shown Status indicators for starboard bow thruster Only shown in a dual bow thruster setup Battery indicator will be shown here in a single DC electric bow thruster setup Status indicators for starboard stern thruster Only shown in a dual stern thruster setup Battery indicator will be shown here in a single DC electric stern here in a single DC electric stern thruster setup thruster setup Examples of display view for different panels applications PJC211 221 PJC221 PJC221 DC Electric Bow thruster Hydraulic Bow thruster AC Electric Bow thruster PJC212 222 PJC222 PJC222 DC Electric Bow thruster Hydraulic Bow thruster AC Electric Bow thruster DC Electric Stern Thruster Hydraulic Stern Thruster Hydraulic Stern Thruster PJC212 PJC222 PJC211 221 Dual DC Electric Bow thrusters Dual Hydraulic Bow thrusters DC Electric Stern thruster Dual DC Electric Stern thrusters Dual Hydraulic Stern thrusters PJC222 Dual AC Electric Bow thrusters PJC221 PJC221 Dual AC Electric Bow thrusters Dual AC Electric Bow thrusters Dual Hydraulic Bow thrusters 6 PJC211 212 221 222 version 2 1 0 2015 Symbols explanations DC Thrusters Battery indicator From 8 5V to 12V for 12V thrusters 15V to 24V for 24V thrusters Motor temperature indicator From 70 C 158 F to 130 C 266 F Symbol shown when a DC Thruster is used in a dual bow or
4. dual stern setup Battery indicator From 8 5V to 12V for 12V thrusters 15V to 24V for 24V thrusters Motor temperature indicator From 70 C 158 F to 130 C 266 F AC Thrusters Motor temperature indicator Hydraulic Thrusters HYD cH Hydraulic oil temperature indicator Retractable Thrusters Symbol shown when the thruster deploys Symbol shown when the thruster retracts Symbol shown when the thruster is in position OUT When the thruster is deployed and no input is given via the joysticks buttons over a 10 second period the panel will give an audible signal every 10th second to tell that the truster is still deployed PJC211 212 221 222 version 2 1 0 2015 Symbols explanations Thrust power and direction Bow thruster s Input from bow joystick on this panel The thrust indicator will be shown in this position on a single joystick panel if the thruster is defined as a bow thruster Thrust power and direction Stern thruster s Input from stern joystick on this panel The thrust indicator will be shown in this position on a single joystick panel if the thruster is defined as a stern thruster mh 1 ne Iftwo or more units are set to run the thruster in SHC opposite direction this information will not be shown Indicating amount of thrust set by other control units in the system ew i e additonal PJC panels 8700 Retract panel i
5. will be erased from memory Setup procedure must be followed to reconfigure the system 12 PJC211 212 221 222 version 2 1 0 2015 Setuo procedure The setup procedure requires knowledge of the serial numer and location of all the S link devices Write this down in the form on the last page to have the information at hand when doing a manual setup Atthe first startup of a new system one of the two screens below will be shown CE 1 SETUP DO NOT MATCH SYSTEM MATCH SYSTEM vV FOR AUTO SETUP FOR AUTO SETUP New devices found Not in conflict with other devices Press button below the symbol to auto setup Thrusters can not be operated to auto setup is completed 2 RUN SETUP DEVICES IN CONFLICT Detected devices in conflict Two or more thrusters defined as same instance bow stern bow STB Stern STB Run Setup procedure to correct Thrusters cannot be operated until seup is completed 2 1 Press and hold the button marked MENU for 3 seconds to enter the menu system Use the stern joystick to select SETUP Press button below the EEE symbol to enter the SETUP menu Kua 2 2 SHEAN HH Use the stern joystick to select SYSTEM DEVICES I Press button below the ESS symbol to enter the SYSTEM DEVICES menu 2 3 Use the stern joystick to set the pin code one number at the time press button below the IE symbol to jump to next number and confirm The pin code is 9 9 9
6. 2015 Product Features Control panel with S link CAN bus connection Product features For proportional thruster control with DC AC and Hydraulic Thrusters Finger tip control speed control with purpose designed joysticks Hold function for easy docking runs thrusters at selected power Back lit LCD display with instant feedback System status alarms Amount of thrust amp direction of thrust Interactive multi language menus CAN Bus communication with thrusters and accessories Plug amp play cables with compact connectors Diagnostics and system setup via panel Built in audible alarm buzzer Connector for external buzzer loud audible alarms Supports Side Power retractable thrusters with or without Speed Control bal k i PJC211 PJC212 PJC221 PJC211 212 221 222 version 2 1 0 2015 PJC222 Panel layout amp functions PJC 211 Information display see following pages for details Press both ON but tons simultanously to activate control panel PJC 212 Holding function for continous running of bow and stern thrusters together in the direction of the arrows at selected power Press for more and for less power 6 steps u II If any control unit are running the thruster in opposite direction to the hold function the hold function will be deactivated Press both ON buttons simultaneously to activate control panel Press to change bet
7. 9 NOTE Re entering the SYSTEM DEVICES menu within 15 minutes does not require entering PIN code 2 4 For about 2 seconds an hourolass will appear while scanning the S link for devices The devices found in the system is now displayed with their instance thruster type and location and serial number Go through all devices and make sure that they are set to the correct instance and function refer to detailed instructions in the SETUP section of Menu System chapter Press button below the BEC symbol to save setting and return to Setup Menu PJC211 212 221 222 version 2 1 0 2015 13 Venu system SETUP SETUP e Move between menu items with the stern joystick Press the button below ES to select the highlighted menu entry Setup Press the button below EE to return to the previous menu Default in systems Setting done under SETUP will be sent to all other panels in the system without stabilizers SYSTEM DEVICES View all devices connected to S Link and manually change setup val SVETEM DEVICES ues CHLIERHTI H A PIN code is required to enter the SYSTEM DEVICES menu Use the stern joystick to set the pin code one number at a time press button below the EE symbol to jump to next number and confirm The pin code is 9 9 9 9 The number of devices found is shown in the upper right corner of the NKU Enter Fin Code dha Use stern joystick to move between the installed devices pa The
8. N button opposite direction to the hold for 1 second to activate function the hold function will control panel be deactivated Press to de activate control panel or cancel or go back in menu system or mute internal alarm buzzer Press to change between day and night light Press and hold for 3 seconds to enter menu system Emergency stop button PJC 222 Holding function for auto run ning of bow and stern thrusters together in the direction of the Speed control joystick arrows at selected power al for bow thruster II Press for more and for less power 6 steps Speed control joystick If any control unit are for stern thruster running the thruster in lt A opposite direction to the hold function the hold function will be deactivated Information display see following pages for details Press and hold ON button for 3 seconds to activate Press to de activate control panel control panel or cancel S or go back in menu system Press to change between day and Emergency night light Press and hold for 3 stop button seconds to enter menu system PJC211 212 221 222 version 2 1 0 2015 5 Display in normal use Status indicators for bow thruster Port bow thruster In a dual bow thruster setup Runtime indicator will be shown here in a single DC electric bow thruster setup Status indicators for stern thruster Port bow thruster in
9. O PJC211 212 221 222 PEEL ONER sA nC Control Pane Installation and user s manual v2 1 0 PJC211 PJC212 PJC221 PJC222 SLEIPNER MOTOR AS P O Box 519 N 1612 Fredrikstad Norway Tel 47 69 30 00 60 Fax 47 69 30 00 70 www side power com sidepower sleipner no Made in Norway Sleipner Motor AS 2015 Contents Poduri Poa OE a E E 3 See ee E O EE E E E EEE E hu 4 5 BiTA EE RUE EEE A EA EA cette seen EN ee cee N N A E E E A E aan 6 E A RD IE p E uu ATA E E E E E T E AAT ETE 7 8 A D E R E EEEE N A unsi 9 Alarme AC ana hydraulic AR 3 mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm mmmmmmmmmmmmmmmm mmmmmmr 10 l is E u A E A sinc A EE A N AN E E ea A E EE E E TS 11 Menu system Language Stabilizer default settings iii 12 SD ge e O ii mmmmmmmmmmmmmmmmm mm mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm mmrmmm mrmmmrmrmmmm mmmmmmmmmmmmmmmmmmmmmmikH 13 enii SES i u EE EEE 14 19 E a E E E E E E E EEEE E E N E EE E A E 14 Ia RI een re me A AE ee a A een eee E enn er 14 DO et de be z u nd sus 17 STDC TI mmmmmmmmmmmmmm mmm mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmrmmmrmmmmmmmmmmmmimi 17 de DEAN VITE ER A E E E E E 18 suas is II UIA oh emmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm mmmmmm mmmmmm mr 18 19 i Ais i i mm rem mir rm mne mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm mmmmmmmmmmmmmmm mm mm mmmmkacH 20 Te MOL mmmmmmmm mmm mmrmmrmmmmmmmmmm mmrmmmmmmmmmm
10. YOWMS SEeJi lu UOHAAS leuJe xe yu l S leua xe YUI S ju ipue ejoweipue I PJC211 212 221 222 version 2 1 0 2015 Measurements 10 8 31 8 141 28 PJC211 212 221 222 version 2 1 0 2015 Connections Connections for optional external buzzer audible alarm Supply 12V 24V DC dh fre L e i Internal fuse relay LL External alarm buzzer 12V 24V DC max 0 5A PJC211 212 221 222 version 2 1 0 2015 29 Note type location and serial numbers Fill in the type location and serial numbers of the S link devices installed Keeping this as a reference will make the setup procedure easier Location Bow Bow STB Stern Stern STB S link device ie Thruster AMS PPC800 etc ta D 2 5 3 om D PJC211 212 221 222 version 2 1 0 2015 OO Notes PJC211 212 221 222 version 2 1 0 2015 31 Worldwide sales and service wWww side oower com C2 Moro SLEIPNER MOTOR AS P O Box 519 N 1612 Fredrikstad Norway Tel 47 69 30 00 60 Fax 47 69 30 00 70 www side power com sidepower sleipner no
11. alues 1 5 Set level of panel backlight in daylight mode 1 is lowest intensity 5 is the highest BACKLIGHT NIGHT COLOR Values GREEN BLUE RED WHITE Select color of backlight in nightlight mode BACKLIGHT NIGHT LEVEL Values 1 3 Set level of panel backlight in daylight mode 1 is lowest intensity 3 is the highest TIMER AUTO OFF Values OFF 01 60 min Set the time from last use to auto panel shutdown Set from 1 60 minutes in 5 minute steps 1 minute steps from 1 to 5 minutes or OFF panel will not turn off automatically UNIT TEMPERATURE Values CELSIUS Default FAHRENHEIT Set the panel temperature displaying unit WHEN RETRACT IS OUT Values NO WARNING Default WARNING EVERY 10sec Select WARNING EVERY 10sec for external buzzer or lamp warning every 10 seconds when retract is out This will activate the internal relay for 0 2 seconds every 10 seconds while the retract is out See page 26 for buzzer connections PJC211 212 221 222 version 2 1 0 2015 UNIT TEMPERATURE CELSIUS CE HHEH RETRACT IS OUT HO HAFHIHG 23 Alarm descriptions Alarm Man Auto E D Errors shown in display Reset Description Action Motor Overcurrent Motor current over 1400A Thruster must be serviced by authorized personnel reset or PPC800 power OFF ON Motor Overtemp Yes Motortemp has been over Motor cool down below 115 C 239 F 130 C 266 F 110 C 230 F for 100 C 212 F for PPC800 FW V1 012 and PPC800
12. alve Thruster Stern without Bypass Valve CMS SO Bas tion OLL STEERHI l 1 Sn HEC A mr e Menu X Setup Default in systems without stabilizers system SETUP 2 PDC 201 SAC Controller Press the button below EE to return to the previous menu Press the button below EE to edit the selected parameter Parameter value will start to blink use joystick to alter value Press the button below to save edited parameter to device Press the button below EE to cancel editing without saving 2 1 Location Values BOW STERN BOW STB STERN STB Set the location for selected device Use BOW or STERN in a conventional thruster system In a system with two bow or stern thrusters i e a catamaran use BOW or STERN for port thruster BOW STB or STERN STB for starboard thruster 2 2 Direction Values Normal default Inverted Switches between Normal and Inverted running direction for the thruster Directio ri Hormal FH Y16006 SH 130361 WAN 4 EE 3 PDC 101 SAC Controller This device is not able to edit Pre setup from factory Press the button below EE to return to the previous menu PDC101 must be setup by authorized personnel Firmware version and serial number is Not Available NA 3 1 Location Values BOW STERN BOW STB STERN STB BOW or STERN in a conventional thruster system In a system with two bow or stern thrusters i e a catamaran BOW and STERN is port thruster BOW STB a
13. arm at all panels and show the alarm info screen WARNING HIGH SPEED STABILIZER NOT ACTIVE Only for yachts equipped with a Side Power Stabilizer system Warning will show when yacht is driven at high speed with stabilizer system inactive Please refer to the Stabilizer ECU manual for speed settings Pressing button below RS ute buzzer alarm at all panels and show the alarm info screen 10 PJC211 212 221 222 version 2 1 0 2015 Venu system E DE PCAER Access menu system by pressing and Ta 2 holding Menu button for 3 seconds Feet J er mm mu I s Move around in menus by using joysticks j H Follow instructions on the screen and press the a buttons below the symbols indicated on LCD screen Len Le el CNE PJC 212 PJC 222 MAIN MENU ITEMS Move between main menu items with the stern joystick i J A LANGUAGE STABILIZER DEFAULT SETTINGS PANEL SETUP S G l is i Wa L ca i yw l i yw Ith Ca TN r Language Stabilizer Setup Info Default settings Panel setup If installed BUTTON SYMBOLS On the bottom line of the display a symbol will be shown over the buttons below These symbols will show what function each corresponding button has in the selected menu entry Return to Select highlighted Edit highlighted Cancel editing This symbol previous menu menu text Save parameter without saving indicates that the edited parame
14. ds Cooling Pump is turned OFF 1 6 Tank Monitor Values ON default OFF ON is when you have a tank monitor oil level and Oil temp sensor OFF is when you do not have a tank monitor and the display will show 0 C and no alarm for high temperature or low level will not be transmitted on the S link 1 7 Thruster Bow only available for PHC024 with FW V1 105 or higher Values without Bypass Valve default with Bypass Valve All 513mm 20inch tunnel and 610mm 24 inch tunnel thrusters are supplied with hydraulic bypass crossover valve and must be set to with Bypass Valve This bypass valve is normally open to protect the thruster during decelera tion and will close while thruster is running By selecting with Bypass Valve you activate this signal and addition change ramp parameters to match this setup All other thrusters must be set to without Bypass Valve PJC211 212 221 222 version 2 1 0 2015 enr Controlled Fu Y11602 S AAbbbed4 oct Coolina Fume Teme Controlled Cooling Sianal Quteut Hor mal Power Save DH FH MIAGE SH GGGE dd lt A Fan FURT IFA 1162 5 HGGGE 44 bca wee Thruster Bow without Bursss We 1 15 Venu system SETUP X SETUP 16 1 8 Thruster Stern only available for PHC024 with FW V1 105 or higher Values without Bypass Valve default with Bypass Valve All 513mm 20inch tunnel and 610mm 24inch
15. e retract manual Warning Low Voltage PJC211 212 221 222 version 2 1 0 2015 25 Technical soecitications Description Minimum Maximum Units Comment Inputvotage fen vorpe Powered from S Link CurrentVoltage tz0 fm External Alarm Buzzer Voltage sr vroce External Alarm Buzzzer Current soo ma Internallyfused Gua em Co ET 26 PJC211 212 221 222 version 2 1 0 2015 esnJ INV M Asoyye aye OSN NW U21IAAS UleW jenuen peq peq YoOUMS urew enue A j J 1snuu U1 S J sniu mog 10 f 2 68 CL 2 68 f 1168 CL 2 68 FS ZL Yeici lepou d3S Wa ue J9 SNJU UJS S Avie Avz cl era peu peu yoeq a i 8 WG algeonlnuu pexi4 g H WG lqeoninuu pexi4 le 7 lege Lele lel c T iddns yull S T C7 i AVTITL i D yS 3 YOUMS JJO UO yul S pol I8pouu 435 J sniu mog MOJ 2 S link system example J8 01U09 JOMOd jeuoodold 1Jo euluuj9 pug uoles u19 S pue mog sa j ued Iouo5 yons of jeuoodold CLE Od i Ayisejod jeuILU19 Aeq Odd ISAO uu s s j01 U09 AUIJ S uo EJS Jt UI9JS pue mog j ued jo1 uo9 yons of IPuoniodoid CLE Od 19 01 U09 JOMOd Odd IPeuoniodoid 1 ae T aa dk gt x x Y JO eululJ9 pug euondo jeuondo O9BJOJUI
16. emote only PJC211 212 221 222 version 2 1 0 2015 FH LES STEFH Thrust Thrust FH We S HiBBn1E7 gt A ES veal v1 208 S H688754 Menu system SETUP X SETUP Default in systems without stabilizers HOLD CALIBRATION SETUP Calibrates the HOLD function to get balanced thrust from the bow HOLD CALIBRATION and stern thruster If only one thruster or PJC221 PJC211 you will not get any balanced thrust but you can adjust the maximum thrust from HOLD buttons Hold button represents 1 6 if the calibrated value Note HOLD CALIBRATION is not available until SETUP is completed To start calibration press the Hold button in the desired direction For a first time calibration the thrusters will start at 70 A system previously calibrated will start with the last amount of thrust set ET ete AJL ILES Adjust power with the joystick Press the button below ESS to save the calibration values Press the button below EE to cancel calibration without saving Note Setup calibration in one direction sets values for both directions PJC211 212 221 222 version 2 1 0 2015 21 Venu system INFO Ta INFO THRUSTER HEC e Move between menu items with the stern joystick 1 e Press the button below ESS to select the highlighted menu entry e Press the button below to return to the previous menu THRUSTER INFO Display info about the thusters in the syste
17. list of devices found can fill more than one screeen FOUHO A scroll bar indicates the position of the selected item STHRBOHRL NOTE Re entering the SYSTEM DEVICES menu within 15 minutes does not require re entering PIN code 1 PHC 024 Controller for hydraulic thrusters Tank Monitor Most functions requires PHC 024 with firmware V 1 101 or newer Instance Fu Y11602 SC HEBEZ44 Move between PHC 024 parameters with the stern joystick ETE LL CE Press the button below EE to return to the previous menu Press the button below EE to edit the selected parameter Parameter value will start to blink use joystick to alter value Press the button below to save edited parameter to device Press the button below EE to cancel editing without saving see section 4 page 16 1 1 Bow Stern Direction Values Normal default Inverted Switches between Normal and Inverted Stern Direction running direction for the thruster Eee eve hin Direction need to be inverted if incorrect prop rotation i gt 14 PJC211 212 221 222 version 2 1 0 2015 Venu system SETUP X SETUP 1 2 Pump Control PTO Mounted Pump Values Auto default Always ON Not Available When Pump Control is set to Auto the system will automatically control load sharing between two PTO pumps by deactivating the second PTO pump when not needed two PTO pumps control valves required to reduce heat generation in the system and save fuel energy
18. m The number of thrusters controllers found is shown in the upper right corner of the display Use stern joystick to move between the installed devices Press the button below EE to select the highlighted menu entry Press the button below ES to return to the previous menu The list of devices found can fill more than one screen A scroll bar indicates the position of the selected item The joystick s operates the thrusters as normal while info is displayed This will be useful for troubleshooting service and general system diagnostics PPC800 DC Speed Control SR1 50000 Control unit for SRV80 SRV100 SRV130 SRV170 SRV210 SRH a EE MP SR61242 Control unit for SR80 SR100 Contr Lou MotorTemp Temperature measured at the electric motor brushes _ Thrust Ha Not implemented in SR61242 s an B Bkll Contr Temp Temperature measured inside the controller Not implemented in SR61242 Voltage Motor Voltage measured at the controller Thrust Thrust level from joystick hold buttons A kKW Retract angle SR150000 Motor Current PPC800 Effect reading PPC800 SR150000 retract angel is 0 when fully deployd and about 90 when retracted Put SR150000 in service mode and operate the controller manually in an out to read the two end position angels for service and installa tion Press the button below ES to return to the previous menu PHC024 Controller for hydraulic thrusters nil a Oil Pressure Oil pressure meas
19. menu Press the button below EE to edit the selected parameter Parameter value will start to blink use joystick to alter value Press the button below to save edited parameter to device Press the button below EE to cancel editing without saving 6 1 BOW STERN Thrust Values 0 100 Default 75 Set the amount of thrust given by the remote control In a bow stern configuration try to balance the thrust so that the boat moves straight sideways when both thrusters are operated simultanously with input from the remote only 7 MSI8730 S Link Interface Move between parameters with the stern joystick Press the button below ES to return to the previous menu Press the button below to edit the selected parameter Parameter value will start to blink use joystick to alter value Press the button below to save edited parameter to device Press the button below EE to cancel editing without saving 7 1 Location Values BOW STERN BOW STB STERN STB Set the location for selected device Use BOW or STERN ina conventional thruster system In a system with two bow or stern thrusters i e a catamaran use BOW or STERN for port thruster BOW STB or STERN STB for starboard thruster 7 2 Thrust Values 0 100 Default 75 Set the amount of thrust given by the remote control In a bow stern configuration try to balance the thrust so that the boat moves straight sideways when both thrusters are operated simultanously with input from the r
20. mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm mmmrmmmmrmmrmmmmmH 20 FON Cee LS A EE 21 SR BlO ma 22 Mem usysterm Panel DEU ama 23 VMTN STACI S hm mire A N EE E E EE A A E E AE E 24 25 CS S ail sir si uuu E EE E E EE ANE E A EAEE E A TE 26 p SS e T accede E eo E E AE E E A E TA A E EAEE T A TTE A E T ET 27 Vens wreme uuu a S a EE E E E E E EEA ET E 28 C OH ail so uuu E eg pas A A E EA E EA E E E E E EE A A es 29 DO NOT connect any other control equipment to the S link controlled products except Side Power original S link products or via a Side Power supplied interface product made for inter facing with other controls Any attempt to directly control or at all connect into the S link control system without the designated and approved interface will render all warranties and responsi bilities for the complete line of Side Power products connected void and null If you are interfac ing by agreement with Sleipner and through a designated and approved interface you are still required to also install an original Sidepower control panel to enable efficient troubleshooting if necessary DECLARATION OF CONFORMITY We Sleipner Motor AS C P O Box 519 N 1612 Fredrikstad Norway declare that this product with accompanying standard remote control systems complies with the essential health and safety requirements according to the Directive 89 336 EEC of 23 May 1989 amended by 92 31 EEC and 93 68 EEC 2 PJC211 212 221 222 version 2 1 0
21. n off all panels Go for lower speed deeper water and retry 24 PJC211 212 221 222 version 2 1 0 2015 Alarm descriptions Alarm mere Auto oq Errors shown in display Reset Description Actuator Fault Pos Sensor Fault In Service Mode High Oil Temp Low Oil Level Warning Return Filter Warning Pressure Filter Yes Warning High Speed Stabilizer Fault Check actuator connection or power to actuator Reset alarm in alarm menu on PJC 211 212 221 222 or recycle power Retract position sensor fail Check position sensor cables and for sensor damage Retract controller in service mode Check dipswitch setting on retract control box Hydraulic oil temperature is higher Stop running and wait for temperature than 75 C 167 F to drop Check if cooling pump is running Hydraulic oil level is to low Fill more hydraulic oil to the hydraulic tank N Return filter element requires replacing Pressure filter element requires replacing WARNING High Speed Stabilizer not active Any Stabilizer alarm See stabilizer panel for more info Actuator not getting any power T AC Motor Overtemp Hydraulic AC motor power pack overtemp Higher than 120 C 248 F Hydraulic AC motor power pack temp sensor open curcuit See manual for more details See SAC manual for more details Check VFD for more details Check VFD for more details Check VFD for more details Calibrate drive shaft alignment se
22. nd STERN STB is starboard thruster 3 2 Direction Values NA Not Available PJC211 212 221 222 version 2 1 0 2015 17 Menu system SETUP X SETUP Default in systems without stabilizers 18 4 MAIN SWITCH Press the button below WEZZE to return to the previous menu Press the button below EE to edit the selected parameter Parameter value will start to blink use joystick to alter value Press the button below to save edited parameter to device Press the button below EE to cancel editing without saving 4 1 Location x Hain Switch Values BOW STERN BOW STB STERN STB Location EOHESTE Set the location for selected device Use BOW or STERN in a conventional thruster system In a system with two bow or stern thrusters i e a catamaran use BOW or STERN for port thruster BOW STB or STERN STB for starboard FH L SA eg an thruster 5 PPC800 DC Speed Control SR150000 Control unit for SRV80 SRV100 SRV130 SRV170 SRV210 SRH SR61242 Control unit for SR80 SR100 Move between parameters with the stern joystick Press the button below ES to return to the previous menu Press the button below EE to edit the selected parameter Parameter value will start to blink use joystick to alter value Press the button below to save edited parameter to device Press the button below EE to cancel editing without saving 5 1 Location Values BOW STERN BOW STB STERN STB Set the location for selected device U
23. nput via 8730 S link external switch interface S link remote control etc FIRST TIME SETUP After installation of an S link thrusters system a System Setup procedure to setup control panels thrusters and additional equipment must be completed ref procedure on page 13 before the system can be used Write down all the S Link devices and serial number one page 27 8 PJC211 212 221 222 version 2 1 0 2015 Alarms DC System When there is a problem or a fault the panel will show this alarm situation by changing LCD display backlight to red color The panel will also change to show Alarm Info EEE on the bottom of the screen indicating that by pressing the corresponding button below you will get information about what the problem is examples below Example PJC 212 Example PJC 222 Alarm code Alarm description Button below this symbol pressed Name and location of ALARHSE device EEE No of alarms Scroll bar L Motor Overtenr Low Voltage Reset alarm and Return Use joystick to scroll if more than two alarms Refer to Alarm code overview table on pages 18 19 for full description on the different alarm codes Non auto reset alarms Some alarms do not reset and needs confirmation from user to be reset This alarms need reset 11 12 13 Motor Overcurrent Controller Overtemp Low Voltage IPC Error Critical Error Low Motor Current Motor Contact
24. or System Error No Communication Motor Temp Sensor 14 Supply Voltage Fault 15 Fuse Blown 17 Motion OUT Fault 18 Motion IN Fault 19 Actuator Fault 20 Pos Sensor Fault 23 Low Oil Level 29 AC Motor Sensor Fault 34 VFD Fault 35 Warning Low Voltage When using the HOLD function The internal and external if fitted buzzer will give the following warning signals __ Warning signals ES mu UU 1 Single short beep every 2 4 sec 2 Two short beeps every 2 4 sec 3 Red backlight in display and continous short beeps 4 Red backlight in display and continous short beeps Voltage below 9 3V 17 SA 2V 24V system Temperature above 85 C 185 F 80 C 176 F for PPC800 FWV1 013 or older SR150000 FW V1 006 or older Voltage below 8 9V 16 3V 1 2V 24V system Temperature above 100 C 212 F 90 C 194 F for PPC800 FW V1 013 or older SR150000 FW V1 006 or older Voltage below 8 5V 15V 4 2V 2AV system Temperature above 115 C 239 F 100 C 212 F for PPC800 FW V1 013 or older SR150000 FW V1 006 or older If one or more of the thrusters enters an alarm state Voltage below 8 Volts both 12 and 24 Volt t systems or temperature above 130 C 266 F 110 C 230 F for PPC800 FW V1 013 or older SR150000 FW V1 006 or older PJC211 212 221 222 version 2 1 0 2015 None None None HOLD function are cancelled Both thrusters will stop Temperature must 5 drop bel
25. ow 115 C 239 100 C 212 for PPC800 FW V1 013 or older before the thruster can be operated again Alarms AC amp hydraulic thrusters When there is a problem or a fault the panel will show this alarm situation by the LCD display in red color All alarms will show in display when panel is turned OFF This requires the S link and other system devices have power Critical alarms will activate internal and external buzzer a long beep every 2 seconds The buzzer can be silenced by pushing the button below BS ihis will also silence all other panels in the system CRITICAL ALARMS goes below 10bar the HOLD Emergency stop function is deactivated 22 High oil temperature 23 Low oil level 26 High speed stabilizer not active 2 Stabilizer fault 28 Hydraulic AC motor power pack overtemp 2 AC thruster sensor fail AC 31 AC thruster overtemp SPECIFIC ALARMS STOP BUTTON Pressing the STOP button on a hydraulic panel will activate the dump valve and all hydraulic consumers will be disabled NB FOR EMERGENCY USE ONLY Panel will not run thrusters Pressing button below RE ute buzzer alarm at all panels and show the alarm info screen ALARM SHOWN ON INACTIVE PANELS This screen will be shown on inactive panels if any of the following critical alarms occur Low oil level High oil temperature Hydraulic AC motor power pack overtemp AC thruster overtemp AC thruster fail Pressing button below es mute buzzer al
26. se BOW or STERN in a conventional thruster system In a system with two bow or stern thrusters i e a catamaran use BOW or STERN for port thruster BOW STB or STERN STB for starboard thruster FH 1414 SH eu walt PJC211 212 221 222 version 2 1 0 2015 Venu system SETUP 5 2 Direction Values Normal default Inverted Switches between Normal and Inverted SETUP running direction for the thruster Default in systems without stabilizers 5 3 Function Values SR V L ON OFF SRP 80 100 SRVP 130 210 SEP 30 240 SRVP 80 100 SRH SRHP Setup the control unit behaviour SR V ON OFF Retract thruster without speed controller PPC800 PHC 024 SR61242 or SR150000 SEP 30 240 Tunnel speed thruster PPC800 without retract SRP Retract SR61242 with PPC800 both devices needs to be set to SRP 80 100 SRVP SRLP Retract SR150000 with PPC800 both devices needs to be set to SRVP SRLP SRHP Proportional Hydraulic retract This needs the PHC024 controller a wee sein Picoza SR V L ON OFF SRP SEP 30 240 SRHP RS PS gt j xi gt J SRVP SRLP ox ix J j ox T ix x PJC211 212 221 222 version 2 1 0 2015 19 Menu system SETUP X SETUP Default in systems without stabilizers 20 6 RCRS 1 S Link Radio Remote Receiver Move between parameters with the stern joystick Press the button below EE to return to the previous
27. ter stern joystick is used to move between menu items parameters PJC211 212 221 222 version 2 1 0 2015 11 Venu system LANGUAGE NU Choose language by moving joystick x SERRE LANGUAGE English Norwegian German French DEUTSCH Spanish Italian and Danish aid e Press the button below to set ITALIANO the language to the highlighted menu E 4 entry A star on each side indicates the laguage set STABILIZER yp Shown only for yachts equipped with a Side Power Stabilizer system Press the button below EE to edit the selected parameter ON OFF will start to blink use joystick to alter value l Press the button below ES to save edited parameter to device Default in systems with stabilizers 1 Stabilizer E _ STABILIZER STABILIZER e Values ON OFF Sem e Switches the stabilizer ON or OFF STABILIZER 2 AnySpeed e Values ON OFF e Switches the zero speed at anchor stabilization ON or OFF DEFAULT SETTINGS Reset all settings to factory default follow instructions on screen DEFAULT SETTIHGS PRESS x FUR DEFAULT SETTIMGS Press the button below to confirm reset bsi e Muse assqa x e The following parameters values will be set to the factory settings DEFAULT Language English Backlight Level Backlight Night Color Green Backlight Nightlevel 1 Timer Auto Off 05 min Hold Calibration 70 Bow and Stern All system devices
28. tunnel thrusters are supplied with hydraulic bypass crossover valve and must be set to with Bypass Valve This bypass valve is normally open to protect the thruster during decel eration and will close while thruster is running By selecting with Bypass Valve you activate this signal and addition change ramp parameters to match this setup All other thrusters must be set to without Bypass Valve 1 9 Thruster Function only available for PHC024 with FW V1 105 or higher Values BOW STERN default BOW BOW STERN STERN Thruster function is how the two thruster valves are set to work BOW STERN One thruster valve output runs on bow signal from control device and the other thruster valve output runs on stern signal from control device BOW BOW Both thruster valve outputs runs on bow signal from control device STERN STERN Both thruster valve outputs runs on stern signal from control device 1 10 1 7 if PHV024 FW version is lower than V1 105 Instance Values default PORT STARBOARD Setting the PHC024 tank controller instance For a mono hull boat the instance should be If you have a catamaran with two PHC024 controllers then the one in the port hull should be set as PORT and the one in the starboard hull as STARBOARD This way the two controllers are shown in the panel display as two different oil tanks to monitor PJC211 212 221 222 version 2 1 0 2015 ster withic ut Bore ass v
29. ured at system oil tank Oil Temp Oil Temp Temperature measured inside the oil tank Bow Thrust g U Stern Thrust Bz Bow Thrust Thrust level from joystick hold buttons EU s1402 S H GGnedd Stern Thrust Thrust level from joystick hold buttons to o o FW Version number Firmware S N Serial number of the PHC 024 Press the button below ES to return to the previous menu PDC100 and PDC 201 Controller for AC electric thrusters PCH EUH Motor Speed RPM on motor output shaft shel sanan pe Motor Power Motor power consumption in PDC201 only Motor Temp Motor Temp Temperature measured in motor Thrust Thrust Thrust level from joystick hold buttons Press the button below ES to return to the previous menu PANEL INFO Display info about the control panel FW Version number Firmware HW Version number Hardware S N Serial number of the control panel Voltage S link system voltage measured at the panel Press the button below to return to the previous menu voltase 22 PJC211 212 221 222 version 2 1 0 2015 Venu system PANEL SETUP PANEL PANEL SETUP Move between parameters with the stern joystick Press the button below EE to return to the previous menu Press the button below to edit the selected parameter Parameter value will start to blink use joystick to alter value Press the button below to save the edited parameter Press the button below EE to cancel editing without saving BACKLIGHT LEVEL V
30. ween day and night light Speed control joystick for thruster Holding function for auto running of bow and stern thrusters together in the direc tion of the arrows at selected power II Press for more and for less power 6 steps If any control unit are running the thruster in opposite direction to the hold function the hold function will be deactivated Press to de activate control panel or cancel or go back in menu system or mute internal alarm buzzer Press and hold for 3 seconds to access menu system and choose items in menus Press to change between day and night light Speed control joystick for bow thruster Speed control joystick for stern thruster Information display see following pages for details Press to de activate control panel or cancel or go back in menu system or mute internal alarm buzzer Press and hold for 3 seconds to access menu system and choose items in menus PJC211 212 221 222 version 2 1 0 2015 Panel layout amp functions PJC 221 Speed control joystick for thruster Holding function for auto run ning of bow and stern thrusters together in the direction of the arrows at selected power II Press for more and Information display see for less power steps following pages for details l any control unit are running the thruster in Press and hold O
Download Pdf Manuals
Related Search