Home

user manual

image

Contents

1. CS 300G USER MANUAL Please read this manual carefully before use USER MANUAL Laserworld Proline CS 300G 9 Table of contents SAFETY INSTRUCTIONS OPERATING DETERMINATIONS PACKAGE LIST PRODUCT INTRODUCTION FUNCTION INTRODUCTION INSTRUCTIONS CHANNEL S FUNCTION SIGNAL CONNECTION AND ADRESS DIALING SAFETY MARKS 10 MAINTENANCE 11 TECHNICAL SPECIFICATIONS Checking Parts Please check if the following parts are included 1 x CS 300G Laser 1 x Power cable 1 x User manual Page 2 of 10 Page USER MANUAL Laserworld Proline CS 300G Page 3 of 10 DANGER LASER RADIATION Avoid direct eye exposure Laser radiation can cause eye damage and or skin damage All protective measures for a safe operation of this laser must be applied 1 SAFETY INSTRUCTIONS Ifthe device has been exposed to drastic temperature fluctuation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature 1 The laser must only be used for shows The operation is only allowed if it is controlled by a skilled and well trained operator Never leave this device running unattended and keep it away from children and unauthorized persons 2 Keep away from heaters and other heating sources In order to safeguard sufficient ventilation leave 50 cm of free space around the device 3 Never direct the laser beam to
2. and light type of different specifications gt Do not expose to the laser light outside gt Do not use it trequently under the humid atmosphere gt Keep the reflecting mirror clean and dry USER MANUAL Laserworld Proline CS 300G Page 9 of 10 10 MAINTENANCE Maintenance should be performed every 15 day period by using a sponge which is dipped with alcohol rather than wet cloth or other chemical liquid to clean the mirror Always disconnect from the mains when the device is not in use or before cleaning it There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers Never look directly into the light source Always disconnect from the mains when the device is not in use or before cleaning it 11 TECHNICAL SPECIFICATIONS Power supply AC 110V AC 220V 50 60 Hz DMX 512 16 channels Condition temperature 10 C 35 C Operating Environment indoor Signal input power 5V 5V Power consumption 150W Working mode Music Control ILDA Optical power Green ca 300mW 532nm Laser classification 3b Weight 15 kg Dimensions 560 x 410 x 230 mm LxWxH PLEASE NOTE This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Laserworld cannot be
3. made liable for damages caused by incorrect installations and unskilled operation USER MANUAL Laserworld Proline CS 300G Page 10 of 10 EU Declaration of Conformity We hereby confirm that the following device Laserworld Club CS 300G Laser Projector complies with the essential safety requirements laid down in the regulations of the committee to assimilate the provisions of law of all participating EU states on the electromagnetic compatibility 89 446 EWG The device has been classified considering the following EU norms on electromagnetic compatibility DIN EN 55103 1 1996 DIN EN 55103 2 1996 DIN EN 61000 3 2 2000 A2 2005 DIN EN 61000 3 3 1995 Al 2001 Assessment of compliance of the product with the requirements relating to the Low Voltage Directive LVD was based on the following standards DIN EN 60065 2002 Furthermore the device is verified in correspondence to the laser class regulations DIN EN 60825 1 if properly set up according to the upper mentioned laser safety regulation After installing the device an inspection and official approval is indispensable for the overall setup The inspection must follow the European guidelines EN 60825 1 and corresponding regulations for the prevention of accidents BGV B2 This declaration is executed on behalf of the CS 300G Laser manufacturer Laserworld e K Tannenweg 11 19 71134 Aidlingen DE Represented by Pe oof 2 i PA 1 J Pa Fi F ri F
4. people or animals 4 CAUTION LASER DIODE Never unscrew the housing There are no serviceable parts inside the device Maintenance and service operations shall only be carried out by authorized dealers 5 Always disconnect from the mains when the device is not in use or before cleaning it HEALTH HAZARD Never look directly into the light source as sensitive persons may suffer an epileptic shock USER MANUAL Laserworld Proline CS 300G Page 4 of 10 2 OPERATING DETERMI NATIONS 6 The operator has to make sure that laser radiation also reflected laser radiation higher than the highest allowed level is avoided by technical or organisational measures 7 Make sure that the used voltage is AC 220V 240V 50 60Hz 8 If the device is used in a flying installation the mounting brackets and an appropriate safety rope must be fixed 9 Laser effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects 10 In some countries the operator must notify the accidence insurance and the authority for industrial safety before operating a laser For more information contact the relevant authorities 11 Please consider that unauthorized modifications on the device are forbidden due to safety reasons 12 1f this device will be operated in any way differently than described in this manual the product may suffer damages and the guarantee becomes v
5. d music control The Club series laser projector was applied for the place of public entertainment such as disco night club and theater etc 5 FUNCTION INTRODUCTION The Club series has 16 DMX 512 control Signal control it can make tunnel effect and animation geometric character and 3D effects Laser sky effects Rolling effects Scanning effects and Laser tunnel effects in all directions And it also has music control The effect can be control by music rhythm 6 INSTRUCTIONS After unpacking check whether the projector has been damaged by transport such as any screw loosening reflecting mirror broken etc If everything is OK select a proper location hang the projector and adjust its angle properly then connect the power cord and the ground wire before switch on at the means Notice that while using this projector the green and yellow wire has to connect the ground properly by Professionals Please examine the electrics and voltage before power on it We suggest customer apply 220V or a transformer 20 seconds after powered on the projector it will self check and then can be used Because the radiate laser generator s own characteristic securing the laser s long life span Please terminate it for 10 minutes after using it for 30 minutes Avoid being interfered by other Signals while using the DMX 512 Signal Controller USER MANUAL Laserworld Proline CS 300G Page 6 of 10 7 CHANNEL S FUNCTION Ch1 Laser pattern A switc
6. h light 0 51 for laser source switch 52 103 for automatic with out breakpoint 104 155 for automatic with breakpoint 156 207 for acoustic control without breakpoint 208 255 for acoustic control with breakpoint Ch2 Laser pattern A selection one pattern every 2 point Ch3 Laser pattern A 0 128 for rotation angle adjustment 129 255 for rotation speed adjustment Ch4 Laser pattern A up down turning 0 128 for adjustment of up down turning angle 129 255 for adjustment of up down turning speed Ch5 pattern A left right turning channel 0 128 for adjustment of left right turning angle 129 255 for adjustment of left right turning speed Ch6 pattern left right moving channel 0 128 for left right movement 129 255 for up down movement Ch7 pattern gradual drawing channel 0 255 for adjustment of gradual drawing Ch8 point adjusting channel 0 128 for adjusting the definition of the point 129 255 for adjusting the length of point Ch9 laser pattern B switch light 0 51 for laser source switch 52 103 for automatic with out breakpoint 104 155 for automatic with breakpoint 156 207 for acoustic control without breakpoint 208 255 for acoustic control with breakpoint Ch10 Laser pattern B selection one pattern every 2 point Ch11 Laser pattern B 0 128 for rotation angle adjustment 129 255 for rotation speed adjustment Ch12 Laser pattern B up down turning 0 128 for adjustment of up down turning angle 129 255 for adjustment
7. i Fa i j Fi i 1 7 a Martin Werner President Aidlingen 01 06 2006
8. igned a data Start address code so that a unit may act on the corresponding control Signal Thus when any Controller is used every unit must have its own data Start address Accordingly the address of the first unit is set as 1 the second unit has also 10 channels so its address code is 11 the third unit is set at 21 so on and so forth the setting method will also depend on the specific console the above Is just for general cases The details of DMX 512 Signal control mode address switch as follow USER MANUAL Laserworld Proline CS 300G Page 8 of 10 Lamp no Start address Control switch ON Bes O O o This Club series has controlled by on off switch address code 1 to 9 are the numerical value DMX 512 Signal 0 is the exchange switch of sound activated control and DMX512 Signal control When 0 is on it can accept sound control When 0 is off it can accept DMX 512 Signal control L R MODE Control switch ON E 1 i Single projector controlled by sound 1 9 OFF 10 ON DMX 512 control 10 OFF u 9 SAFETY MARKS gt Before maintenances please refer to eligible personnel gt Please make sure to switch off the power before Installation or maintenance gt Please do not use power and lasers that do not conform to the current specifications gt Please do not see the laser light directly in case it might damage the eyes gt Avoid electric shock Bulb overheating gt Do not use any power voltage
9. of up down turning speed Ch13 pattern B left right turning channel 0 128 for adjustment of left right turning angle 129 255 for adjustment of left right turning speed Ch14 pattern B left right moving channel 0 128 for left right movement 129 255 for up down movement Ch15 pattern B gradual drawing channel 0 255 for adjustment of gradual drawing Ch16 point adjusting channel 0 128 for adjusting the definition of the point 129 255 for adjusting the length of point USER MANUAL Laserworld Proline CS 300G Page 7 of 10 8 SIGNAL CONNECTION AND ADRESS DIALING When the Controller transmits DMX512 Standard Signals the connection of which is accomplished through the input and output 3 pin XLR socket When a console Signal Outputs to the unit it must correspond to the Pin 1 Ground Pin 2 Negative and Pin 3 Positive of the XLR socket on the unit If tt does not work just try exchanging the Pin 2 and Pin 3 these 2 pins are generally do not need exchanged for consoles The Signal wire length should not exceed 100m in order to avoid the interference of the other Signals by any other electric appliances DMX512 CONTROLLER If your DMX 512signal Controller adopt 5 pins XLR plug you need one transfer line the transfer method as following Mt in 1 GNDYSCREEN J in 2 Signal k P Pin 2 Pin 3 Signall When control Signals from the console inputs into Club series laser light projector The projector must be ass
10. oid Furthermore any other operation may lead to dangers like short circuit burns electric shock etc Thank you for using the Club series laser projector For the sake of safety and better Operation of this projector please read this manual carefully before use and operate the projector lest incur any personal injury or damage to the projector 3 PACKAGE LIST When you unpack the case please take time to examine the items as follow projector 1 Power cord 1 Owner s manual 1 projector sling 1 USER MANUAL Laserworld Proline CS 300G Page 5 of 10 4 PRODUCT INTRODUCTION The Club series projector adopts the latest appearance design to make it compact and light The housing use imported paint It has full solid semiconductor laser source Wavelength is 523nm and emerald green color Laser generator is double temperature controlled power supply The laser light source has a long life span and highly stability complying with the international Standard The scanning System is vibratory mirror DMX 512 Signal 16 channel This product introduced the vibratory mirror control from Britain international Standard DMX 512 Signal control It can printing 2 laser pattern at the same time There are 128 latest laser effect patterns in it can be used for word Chinese English and J apanese performance gt animation performance gt laser beam performance with spatial projection and animation effects Control modes DMX 512 Signal control an

Download Pdf Manuals

image

Related Search

Related Contents

Mode d`emploi  Titan TFD-9225L12Z  Viking F21286 User's Manual  tekniska data  Archives de Haute-Garonne : l`état civil en ligne Mode d`emploi  Kids II 6803-NU User's Manual  毎年8月は「電気使用安全月間」です!  Zebra Technologies 2824 Printer User Manual  CS BEST 310  PJ-520 / PJ-560  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.