Home

3G22WV User Guide

1. 3G WiFi Router with Voice User Guide 49 a gt NetCommWireless Telephony Profile The Telephony Profile page allows you to select the region of your router for the purpose of setting up phone calls There are 3 available regions Default Australia New Zealand Canada and North America The region selected affects settings such as dial tone message wait indicators and conferencing options among others Use the drop down list to select the appropriate region and click the Apply button Remember to reboot the router so that the new settings take effect Set Telephony Profile Set Telephony Profile Telephony profile decides how your phone call is set up Please select one of the profiles based on your current location then reboot the router to make it take effect Telephony Profile North America www netcommwireless com A FA NetCommWireless SMS The SMS tools application has been developed to include basic SMS functionality such as sending a message receiving a message and redirecting an incoming message to another destination You can also utilise this functionality to read and change run time variables on the router Basic functionality Supported Ability to send a text message via a 3G network and store in permanent storage Ability to receive a text message via a 3G network and store in permanent storage Ability to forward incoming text messages via a 3G network to another remote destinati
2. ff E E Gateway IP Address Network Interface Auto Metric 111 65535 Item Route Name Destination IP Address Subnet Mask Gateway IP Address Network Interface Metric Static Route table empty Item Destination Gateway Netmask Flags Metric Ref Use Interface 1 192 168 20 0 0 0 0 0 255 255 255 0 U 0 0 0 brO 2 192 168 1 0 0 0 0 0 255 255 255 0 U 0 0 0 brO 3 239 0 0 0 0 0 0 0 255 0 0 0 U 0 0 0 bro 4 0 0 0 0 10 139 59 14 0 0 0 0 UG 20 0 0 wwan0 Some routes are added by default by the router on initialisation such as the Ethernet subnet route for routing to a device on the Ethernet subnet A PPP route is also added upon obtaining a WAN PPP connection Adding Static Routes e Enter the required values in the fields as shown above for route being added e Click ADD i Please note You must increment the Route no by 1 for each route in the Route no field otherwise that route will be overwritten The Active Routing table at the bottom will then show the new route added Deleting Static Routes Click the Delete Entry text in blue RIP RIP Routing Information Protocol is used for advertising routes to other routers Thus all the routes in the router s routing table will be advertised to other nearby routers For example the route for the router s Ethernet subnet could be advertised to a Router on the PPP interface side so that a Router on this network will know how to route to a device on t
3. Broadcast SSID Enable O Disable Network Authentication 802 1X vw RADIUS Server IP Address RADIUS Port 1812 RADIUS Key o000000 802 1x WEP Disable O Enable Please note After configuring wireless security you also need to configure your wireless adapter to use the same security es settings before you can connect wirelessly Not all wireless adapters support WPA PSK WPA2 PSK WPA WPA2 security Please refer to your wireless adapter user guide for more details It is strongly recommended to set up a simple wireless security such as WPA PSK when the wireless client supports WPA PSk in order to secure your network Most wireless adapters in computers and laptops support at least WEP and WPA 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 39 E gt NetCommWireless Advanced Wireless Settings This page allows you to modify the advanced wireless settings for your NetComm Smart Hub 4G These settings should not be changed unless you are aware of what effect they will have Wireless Settings gt Advanced Advanced Wireless Configuration This page allows you to modify the advanced wireless settings for your Router These settings should not be changed unless you are aware of what effect they will have BG Protection Mode Client Idle Timeout Beacon Interval Data Beacon Rate DTIM Fragment Threshold RTS Threshold TX Power Short Preamble Short Slot Tx Burst Packet Aggregate Countr
4. If a call is already in progress via the first port the user on the handset s connected to the second port will receive a busy signal Incoming calls will ring and can be answered on either port however once a call is answered from one port handset s on the second port will receive a busy signal Handset requirements The 3G22WV allows you to make telephone calls over the 3G network using a standard analogue telephone via the built in RJ 11 Phone ports Please refer to the documentation provided by the manufacturer of your analogue telephone for assistance with the operation of your teleohone handset Maximum REN Loading Please note that each of the line interfaces on the 3G22WV is capable of supporting multiple analogue telephones connected via splitters The ringer equivalence number REN for each line is 5 Therefore a maximum of 5 handsets each with a REN number of 1 can be connected to each line port Before you start making a phone call make sure you check the following 1 You have an activated 3G SIM card inserted prior to powering on the 3G22WV 2 Your 3G22WV is powered on and operating normally 3 A working analogue telephone connected into either the Line 1 or Line 2 port 4 You hear the dial tone and the Line LED on the front of your 3G22WV should light up after lifting the handset How to place a call To make a call simply lift the handset and dial the number following the instructions provided by your telephone handset
5. LL LAN access via cable DU LU G E m tend a In WDS repeater mode access points connect to the router and repeat the wireless signal of the router and also allow connections to wireless clients With the wireless signal divided between linking the router and access points and also between access points and wireless clients the distance possible between the router and access points will be approximately halved when compared with WDS bridge mode LI Laptop Q Q Ll 7 L D Q Laptop NN ge K CI Broadband in WDS Repeater Mode Tower Laptop Wireless Aooess Point I in WDS Mode Laptop 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 43 E EE gt NetCommWireless WPS WiFi Protected Setup WPS is the simplest way to establish a connection between wireless clients and your 3G22WV This method removes the need to manually select the encryption mode and enter in a passphrase key You only need to press a button on both the wireless client and the NetComm Smart Hub 4G router and the WPS feature will complete the wireless connection The 3G22WV supports two types of WPS OPTION WPS via Push Button WPS via PIN code A PIN code needs to be assigned to the wireless client set to WPS mode Then to complete the wireless connection input the wireless client PIN into the 3G22WV web interface Blid NON A specific button needs to be pressed on the wireless clie
6. This ts only requred if your SIM card needs PIN code to be activated 2 2 Z SIM Status PIN Internet Confirm PIN Remember PIN The 3G Operation Mode can be configured on this page Please see the table below for options allowed for the 3G operation mode OPTION Blid NON Automatically Configure My The router will attempt to automatically detect the mobile broadband provider and APN of the inserted SIM car Mobile Broadband If your SIM card has a PIN code or requires a username or password to connect do not select this option Mobile Broadband Select to enable or disable the mobile broadband profile Custom APN if required Enter an APN if the Auto Config option does not correctly identify your mobile broadband service setting s APN Country SIM Status etp eene rareste nant Enter the SIM PIN code numbers here if required Gain PIN PIN Select the country you wish to operate the router in The current status of the inserted SIM If SIM PIN is shown enter the SIM PIN code in the fields below Re enter the SIM PIN code numbers here if Re enter the SIM PIN code numbers here frequired Select to remember the entered SIM PIN Selecting yes for this option means you will not need to enter the PIN Remember PIN code again to use the inserted SIM card You can also elect to enable the Automatically Configure My Mobile Broadband option This option attempts to automatically fill out the correct APN
7. gt NetCommWireless 3G WiFi Router with Voice BG22VWWV USER GUIDE a FA NetCommWireless Copyright Copyright 2013 NetComm Wireless Limited All rights reserved The information contained herein is proprietary to NetComm Wireless Limited No part of this document may be translated transcribed reproduced in any form or by any means without prior written consent of NetComm Wireless Limited A Please note This document is subject to change without notice Save Our Environment When this equipment has reached the end of its useful life it must be taken to a recycling centre and processed separately from domestic waste The cardboard box the plastic contained in the packaging and the parts that make up this device can be recycled in accordance with regionally established regulations Never dispose of this electronic equipment along with your household waste You may be subject to penalties or sanctions under the law Instead ask for disposal instructions from your municipal government Please be responsible and protect our environment This manual covers the following products NetComm 3G22WV DOCUMENT VERSION DAE 1 0 Initial document release 05 12 2011 1 1 Revised to final firmware 25 09 2012 release 1 2 Added Accessing a connected USB drive section 03 01 2013 1 3 Added Telephony Profile section and updated some 24 01 2013 screenshots www netcommwireless com 3G22WV 3G WiFi Router
8. manufacturer How to receive a call When an incoming call is received both Line 1 and Line 2 lights will start flashing and any phones connected to the 3G22WV will ring Answer the telephone following the instructions provided by your telephone handset manufacturer to conduct the call T Please note If the call is answered from a telephone connected to Line 1 telephones connected to Line 2 will receive an engaged tone for the duration of the call If there is no phone connected to the 3G22WV all incoming calls will be transferred to Voicemail if enabled on the account Answering an incoming call when on a call Call waiting enables a 2nd incoming call to be received while you are on a call To answer a call waiting call perform a hook flash briefly depressing the hook button The incoming call should then be answered Upon hanging up or performing another hook flash you will be returned to the original telephone call Accessing voicemail To access your voicemail please dial 98 and follow the voice prompts www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 62 E gt NetCommWireless Call feature codes Quick Reference Table The 3G22WV supports a number of call feature codes for supplementary services FEATURE ACTIVATION DEACTIVATION STATUS Caller ID uy ue N A to block an individual call to unblock an individual call Call Waiting HASH 430 Caller ID Caller ID transmits a caller
9. on FA NetCommWireless Security Settings This section allows you to configure the wireless security for your 3G22WV Setting up sufficient wireless security can prevent unauthorized access to your wireless network SSID and Security Settings SSID 1 NetComm 2607 Click here to edit SSID Activate this SSID LO Enable Disable Broadcast SSID LO Enable Disable Network Authentication WPA Pre Shared Key Click here to display WPA Group Rekey interval WPA Encryption AES OPTION DEFINITION FETT The network name that EEE when you scan for wireless networks to join Activate this SSID this SSID Enables or disables the SSID 4 or disables the SSID Enables or disables the SSID being broadcast When enabled your wireless network is visibly to devices when they Broadcast SSID scan for a network to join Network Authentication Select the security mode for the wireless network See below for more information WPA Pre Shared Key The pre shared key necessary to connect to the wireless network NPA Gun Bale The time in seconds that the WPA group key is refreshed The group key is used to encrypt the wireless connection S y and regularly changing the group key provides extra security to your wireless network In most cases the default value of 600 is sufficient You should not change this setting unless instructed to by technical support WPA Encryption Displays the encryption method in use Interval Network Aut
10. 21 lt Directory Number gt Where directory number is the number you wish to forward calls to Hang up after you hear 2 low pitch beeps To disable Call Forwarding Unconditional dial 21 Hang up after you hear 2 high pitch beeps To check the status of Call Forwarding Unconditional dial 21 or view the advanced status page of the management console o Cal Forwarding Unconditional is disabled if you hear 2 high pitch beeps o Cal Forwarding Unconditional is enabled if you hear 2 low pitch beeps Call Forwarding No Answer Call forwarding No Answer will divert all incoming calls to a phone number that you desire only if the incoming call is not answered To enable Call Forwarding No Answer dial 61 lt Directory Number gt Where directory number is the number you wish to forward calls to Hang up after you hear 2 low pitch beeps To disable Call Forwarding No Answer dial 61 Hang up after you hear 2 high pitch beeps To check the status of Call Forwarding No Answer dial 61 or view the advanced status page of the management console o Call Forwarding No Answer is disabled if you hear 2 high pitch beeps o Call Forwarding No Answer is enabled if you hear 2 low pitch beeps 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 63 E FA NetCommWireless Call Forwarding Busy Call forwarding busy will divert all incoming calls to a phone number that you desire only if your telephone is busy on an
11. E gt NetCommWireless DHCP The DHCP page is used to adjust the DHCP settings used by the router The DHCP settings are then passed onto any device connecting via DHCP You can manually set the DHCP Start and End range the DHCP Lease time the default Domain name suffix Primary and Secondary DNS Server the Primary and Secondary WINS Server as well as the NTP TFTP and Option 150 Option 160 VoIP options settings Internet Settings gt LAN gt DHCP DHCP Configuration DHCP Enable O Disable DHCP Start Range Z 20 DHCP End Range 20 DHCP Lease Time seconds Default Domain Name Suffix DNS Server 1 IP Address o o o lo DNS Server 2 IP Address o o f lbo WINS Server 1 IP Address o o fo j fo WINS Server 2 IP Address o o fo j fo NTP Server Option 42 Z s hoo TFTP Server Option 66 Option 150 Option 160 Cid DHCP Relay O Enable Disable DHCP Server Address Address Reservation List Computer Name MAC Address IP Address Add DHCP Client List Computer Name MAC Address IP Address Expire Time After entering the applicable details click Save You can also assign a particular IP address to a specific device every time that device makes a DHCP request as follows Address Reservation List Computer Name MAC Address IP Address o jo fo jo Enable Click Add Enter a name for the computer or device Enter the computer or devices MAC address Enter the IP address
12. Failure in red By default 10 recipient entry fields are shown on this page however you can increase or decrease this number by pressing the or button at right side of the last recipient entry field You can select to enable or disable individual message recipients by selecting the checkbox beside each entered number After entering the appropriate recipient numbers type your SMS message in the Message Body field and then click the Send button 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 51 E gt NetCommWireless Inbox Outbox The SMS Inbox page allows a user to read delete reply or forward an SMS message to another mobile device To Delete Reply or Forward an SMS message select the applicable message and click the appropriate button for the function you would like to perform Services gt SMS Inbox sms memstbar memory status total 30 used0 free 30 message status Inbox0 Outbox0 rx msg total 0 messages F from time message The SMS Outbox page allows a user to check all SMS messages sent from the 3G22WV Services gt SMS gt Outbox memory status total 30 used0 free 30 message status Inbox0 Outbox 0 4 to time message The Refresh button will refresh the page and show any new messages which have been received www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 52 E FA NetCommWireless system Startup Wizard If you wish
13. Internet Time server This setting will affect functions such as System Log entries and Firewall settings where the current system time is displayed You can use the default NTP server or enter one manually if required www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 46 E FA NetCommWireless System Monitor The System Monitor page is used to configure the behaviour of the Periodic Ping monitor function Services gt System Monitor Periodic PING Settings Destination Address Second Address Periodic PING Timer o 0 disable 300 55535 secs Periodic PING Accelerated Timer bo 0 disable 60 65535 secs Fail Count 0 disable 1 65535 times Periodic Reboot Force reboot every Do 0 disable 5 65535 mins The Periodic Ping Reset Monitor configures the router to transmit controlled ping packets to user specified IP addresses Should the router not receive responses to the pings the router will reboot The purpose of this feature is to ensure the recovery of the router if the internet connection disconnects and does not reconnect for any reason This works as follows 1 After every Periodic Ping Timer configured interval the router sends 3 consecutive pings to the Destination Address 2 If all 3 pings fail the router sends 3 consecutive pings to the Second Address 3 The router then sends 3 consecutive pings to the Destination Address and 3 consecutive pings to the Second Addre
14. LAN Configuration IP Address s s 20 S fi Subnet Mask 255 255 255 0 Transparent Bridging DNS Masquerade GO Enable Disable Save Please note If the IP address has changed you will have to re enter the new IP address configured in your browser to access the configuration pages OPTION DESCRIPTION IP Address The local IP address of 3G22WV Subnet Mask The subnet mask for the local network The hostname you may use in place of the IP address of the router Enabling this field bridges the WAN port to the LAN port The connected LAN device is then live on the Internet To confirm 3G IP Forwarding Mode is functioning check that the local IP address on the Status page matches the IP address of the network adapter on your PC DNS Masquerade Select to enable or disable DNS masquerading for connected clients MBB IP Forwarding Transparent Bridging DNS Masquerading DNS masquerading allows the router to forward DNS requests to dynamically assigned DNS servers Clients on the router s LAN can then use the router as a DNS server without needing to know of the dynamically assigned DNS servers assigned by the cellular network There should be no need to disable this feature in most cases however if you need to do so simply select Disable and click the Save button Click Apply to save any changes you make to the settings www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 24
15. Play UPnP is Enabled and is used by a UPnP network device to be automatically identified by other UPnP devices Select Disable to disable this option Used in multicasting the Router Advertisement function periodically sends ICMP router Router Advertisement discovery messages to identify other routers nearby The default option is Disable Select Enable to enable it PPPoE relay is also known as half bridge mode half bridge and will make the DHCP PPPoE Relay duplicate the WAN IP address from the ISP to the local client PC The default option is Disable Select Enable to enable it The default is Disable select Enable to enable this option The Spanning Tree protocol is used to stop loops when using wireless distribution system WDS links as redundant links in a distribution system www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 26 E FA NetCommWireless WAN The WAN page allows you to configure the optional WAN Ethernet port Select the WAN connection type suitable for your environment and configure parameters according to the selected connection type STATIC fixed IP If your WAN connection uses a static IP address please select STATIC fixed IP and fill in the required information in the fields provided Internet Settings WAN WAN Configuration WAN Connection Type Static Mode IP Address Subnet Mask Default Gateway Primary D
16. The options available for this field are Mixed Mode or Green Field The default operation mode is Mixed Mode The channel bandwidth can be set to a mixed 20 40 MHz the default value giving an 802 11g connection speed of up to 150 Mbps and an 802 11n connection speed of up to 300 Mbps For legacy wireless adapters the Channel Bandwidth can be set to 20 MHz slowing the connection speed for 802 11g and 802 11n to 54 Mbps and 74 Mbps Channel Bandwidth respectively as well as providing backward compatibility for older slower 802 11b g devices The guard interval is designed to help wireless clients minimise the effects of multipath delays When you add a guard Guard Interval time the back portion of useful signal time is copied and appended to the front The options available for this field are Long or Auto The default setting is Auto The Modulation and Coding Scheme MCS function sets the modulation coding and number of spatial channels The default MCS value is Auto The Reverse Direction Grant RDG function reduces the transmitted data packet collision rate by using the reverse Reverse Direction Grant RDG direction protocol The RDG improves transmission performance and scalability in a wireless environment By default the RDG setting is enabled The MAC Service Data Unit MSDU Aggregation function wraps multiple Ethernet frames bound for a common Aggregation MSDU A MSDU destination in a single 802 11 frame This reduces the number of requi
17. and NetComm Wireless Limited s liability for breach of that condition or warranty may not be excluded but may be limited then subject to your rights and remedies under any applicable Consumer Protection Laws which cannot be excluded NetComm Wireless Limited s liability for any breach of that guarantee condition or warranty is limited to i in the case of a supply of goods NetComm Wireless Limited doing any one or more of the following replacing the goods or supplying equivalent goods repairing the goods paying the cost of replacing the goods or of acquiring equivalent goods or paying the cost of having the goods repaired or ii in the case of a supply of services NetComm Wireless Limited doing either or both of the following supplying the services again or paying the cost of having the services supplied again To the extent NetComm Wireless Limited is unable to limit its liability as set out above NetComm Wireless Limited limits its liability to the extent such liability is lawfully able to be limited www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 70 EO FA NetCommWireless FCC Regulations This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This device has been tested and fou
18. computers across one or both of the MBB and Ethernet WAN connections Internet Settings Routing Content Filtering This page allows you to view the LAN WAN and wireless statistics of your Router This page allows you to configure content URL and host filters to restrict improper content access from LAN computers Apply filters on this page to the following connection 35 Web Content Filter Both MBB and Ethernet WAN Connections L Apply Filter Web URL Filter Settings Proxy lava Dlacdivex Lcookies Ae Current Web URL Filters No Add a URL filter URL URL Web Host Filter Settings Current Website Host Filters No Host Keyword Add Host keyword Filter Keyword OPTION Content Filter Settings Web Content Filter URL Filter Web Host Filter Add a Host keyword Filter Blid NON Select which connection type the content filtering will apply to Options include the mobile broadband connection only the Ethernet WAN connection only or both the 4G and Ethernet WAN connections Tick the boxes to enable Proxy Java or ActiveX content filtering Click Apply to save any settings changes Block access to a website by entering its full URL address and clicking the Add button Rules previously created and listed here can be deleted at any time via this page Access to certain websites can be blocked by entering a keyword Rules can be deleted at any time
19. point four 10 100Mbps Ethernet ports with one able to act as a 10 100 1000Mbps Ethernet WAN port and one phone port for making and receiving telephone calls Two USB ports provide connectivity to attached USB Storage for connected clients It features the latest security options such as WPA and WPA2 data encryption SPI Stateful Packet Inspection Firewall and VPN pass through 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com D E FA NetCommWireless Physical Dimensions and Indicators LED Indicators The 3G22WV has been designed to be placed on a desktop All of the cables exit from the rear for better organization The display is visible on the front of the 3G22VWV to provide you with information about network activity and the device status See below for an explanation of each of the indicator lights LED INDICATOR DEFINITION HIGH High 3G Signal strength available MD Medium 3G Signal strength available W Low 3G Signal strength available D W SIGNAL Connection established with 3G network Internet connection established 4 3 2 Solid blue light when the analogue telephone connected to Line 1 is PHONE off hook blinks on incoming call Powered device connected to the LAN port includes devices with Wake On LAN capability where a slight voltage is supplied to an Ethernet connection Blinks on LAN port traffic Powered device connected to the LAN port includes devices with Wake On LAN capability whe
20. shows the encryption type used by the wireless settings WPS Default Key Index This field shows which key index is in use by the wireless settings PIN www netcommwireless com enabled wireless devices WPS Key ASCIl This field shows the current wireless passphrase key in use by the wireless settings WPS Mode Select either PIN mode or PBC which is the WPA via Push Button This is the WPS PIN code of the wireless router You may need this information when connecting to other WPS 3G22WV 3G WiFi Router with Voice User Guide 44 E FA NetCommWireless Station Info The Station List shows the wireless clients currently associated with your 83G22WV Wireless Settings Station Info Station List This page allows you to view a list of the wireless clients that are currently associated with your Router 310 NetComm 2607 OPTION MAC address Host Name IP Address RSSI PSM BW Connected Time 00 22 FA 9F CC AC SALES25 192 168 20 144 4 PWR_ACTIVE 20M 00 00 44 Bled NON SSID The wireless network name MAG Address The wireless client s unique 12 digit hexadecimal identifier The name of the computer or device connected to the router IP Address RSSI PSM The local network address assigned to the wireless client by the router The Received Signal Strength Indicator RSSI measures the wireless signal strength This field shows the Power Saving Mode PSM status The bandwidth field gives an estimation of the
21. the maximum size of a packet during the fragmentation of data to be transmitted If you set this value too low it will result in bad performance When the packet size is smaller than the RTS threshold the wireless router will not use the RTS CTS mechanism to RTS Threshold l send this packet TX Power This determines the transmit or output power of the broadcast wireless signal A radio preamble is a part of a datagram packet at the head of the Physical Layer Convergence Protocol PLCP to increase throughput Shortening the preamble reduces the size of the data packet increasing throughput However not all wireless network adapters are able to use this setting The amount of time the router waits after a packet collision before retransmitting the data packet Enabling the short slot reduces this time from 20ms to 9ms therefore increasing overall throughput The Transmission Burst boosts the WLAN data packet throughput to maximise transmission rates according to the wireless protocol being used However this may increase the rate of dropped packets due to environmental factors such as radio interference which can make the optimal wireless data packet transmission rate less than the maximum possible transmission rate Packet Aggregation in IP networking is a function that concatenates multiple data packets into a single Transmission Unit to reduce redundancy and network traffic overhead Goune Code The Country Code option controls the wireless c
22. to re run the initial setup wizard you can do so by moving the mouse over the System menu and clicking on Start Wizard option Log The Log page is used to download or display the current System Log of the router Log File Display Level All Page lof64 O Level Process Date amp Time Clear Log File 24 Jan 11 18 32 nipdate 3908 step time server 130 102 2 123 offset Jan 24 11 18 32 NetComm Wireless Router user notice ntp template 46 859499 sec Jan 24 11 15 44 NetComm Wireless Router user notice ntp template done Jan 24 11 15 44 NetComm Wireless Router user notice ntp template updating root cond for ntpclient sh Jan 24 11 15 43 NetGomm Wireless Router user notice ntp template updating nipdate 0 netcomm pool ntp ong Jan 24 11 15 43 NetComm Wireless Router usernetise ntp template SEE TTT T Jan 24 11 15 43 MetComm Wireless Router user notice ntp template started Jan 24 11 15 43 NetComm Wireless Router user notice half bridge template half bridging has not been setup simply exit Jan 24 11 15 43 NetComm Wireless Router user notice cantent filtersh started Jan 24 11 15 43 NetComm Wireless Router user notice contentfilter template contenttilter started Jan 24 11 15 43 NetComm Wireless Router user notice route template done Jan 24 11 15 43 NetComm Wireless Router user notice flush conntradk cache done Jan 24 11 15 43 NetComm Wireless Router user notice flush conntradk cache connection tacking table ha
23. via this page Enter a keyword that you want to add to the filter list 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com E gt NetCommWireless Wireless Settings Basic Configuration Settings This page allows you to define the basic wireless settings for the 3G22WV Wireless Settings gt Basic Wireless Setup Radio On Off GO ON Oorr Country Australia Network Mode 11b g n mixed mode Frequency Channel 2412MHz Channel 1 Current Channel 1 SSID and Security Settings SSID 1 NetComm 2607 Click here to edit SSID Activate this SSID Enable O Disable Broadcast SSID Network Authentication WPA Pre Shared Key Click here to display m 3 D o O 2 nH EE G WPA Group Rekey interval WPA Encryption AES Multiple SSID List No Enabled SSID Network Authentication Encryption raas gs ras 1 Yes NetComm 2607 WPA2PSK AES On 2 No GUEST1 WPA2PSK AES On 3 No GUEST2 WPA2PSK AES On 4 No GUEST3 WPA2PSK AES On 5 No GUEST4 WPA2PSK AES On Radio On Off WiFi is turned on by default Changing this option to OFF will turn OFF the wireless functionality on the 3G22WV and you will not be able to connect to your 3G22WV wirelessly OPTION DZANIA Radio On Off Use this option to switch the wireless functionality on or off Ca Select the country that the router is operating in This field has an effect on the wireless channels that are legally available for use in
24. webpage interface and check that the correct APN settings are entered Also check that the username and password credentials are correct if the APN in use requires these Make sure that Auto Connect is enabled on the PPP Profile Connect section on the Data Connection page Check you have suitable 3G signal strength and that your SIM is active and does not require a PIN code to be entered 7 The SIM status indicates that the SIM is not installed or reboot required on the home page If a SIM is installed correctly this may indicate that the SIM has been removed or inserted whilst the unit is powered up In this case you must reboot the unit The Reset button on the home page will reboot the router 8 How can I see the data usage on my NetComm 3G WiFi Router with Voice You can check your current Usage statistics by clicking on the Usage Monitor link at the top of the Status Page in the Advanced View 9 Can make voice calls from the NetComm 3G WiFi Router with Voice Yes By simply connecting a regular landline Analogue telephone to the port labelled Line 1 using the RJ 11 Cable provided To activate the phone jacks in your home or office connect an RJ 11 Cable from the port labelled Line 2 to any wall jack When you lift the receiver you will hear a dial tone and can place your call 10 How do I see I have a voicemail message Voicemail is a feature of the 3G network and your 3G service provider not a feature e
25. wish to use to connect to your mobile broadband provider Please don t edit this APN Name unless you are aware of what effect it will have Mobile Broadband Connection The profile can be disabled or enabled using this option If applicable enter the username assigned to you by your mobile broadband provider in order to connect to the Username l mobile broadband service If applicable enter the password assigned to you by your mobile broadband provider in order to connect to the Password mobile broadband service TE Select the type of authentication in use by the mobile broadband network For more information please contact Authentication Type l your mobile broadband service provider Reconnect Delay The delay between attempts to reconnect to the mobile broadband service Reconnect Retries The number of reconnection tries made to the mobile broadband service S This field allows you to customize the metric of the mobile broadband interface This setting will have no effect for most users but may be required for advanced routing configurations Static Routes RIP VPN etc MTU Enter the Maximum Transmission Unit the size in bytes of the largest datagram packet that can be sent over the network connection NAT Masquerading Enabled by Default this option allows you to switch NAT Network Address Translation on or off Voice Roaming Outgoing Call Enable outgoing voice calls when utilising a different mobile broadband provider Vo
26. with Voice User Guide 2 E FA NetCommWireless Table of Contents OVEIVICW AE E 4 Mon MCO SE EE ENE E E e E OE ENE DERN 4 T E EEE E EE E E EE EE NE E E E AE 4 PU r 4 Teepnon REGUS np 4 IO EPI ecaee a E EN EE 4 OCI d IEE OCG e EHH 5 See Ga TTT 5 FEN 5 ERI SL gt EEE NE NOE ET NE ENE E ENE 5 Physical Dimensions and Ts ee 6 CEREO O a E E E 6 Tees Ge Hee 7 PIC HR eee 8 CC A i AB d lae TE ERE NE EEE EEE ET RE EE re ee er nr eter errr ere 8 AN PTE 9 Bl tere as ko m Eeg RE EE RR NN RK NN NR 9 Installation and Configuration of the 3G22WV rennarnnnnnnnnnnnnnnavnnnnnnnnnnnnnnennnnannnnnnnnnnnnnnnennnnnnnnnnnnnnnennnnennnnnnnnnnennnnennnnennnnnnnnuunnnne 10 PTE Nav 10 POW OOSIACIES and MNI ENCO EEE ERE RE EE EEE NE eteme 10 Coe GO SSE EE EEE EEE EE EE EEE EN 10 Choose the Quietest Channel for your Wireless Network x ee e ee e 10 TN 11 Ge aa les via d CaN EE 11 Connecting Wirelessly ER EE ENA REEE AEAEE E EENE REEE EEEE NEEE ENERE EE NE 11 EA EE SE 0 EEE EE ERE EE EEE NE ENER EEE NE 12 Management Console Login Procedure EE 15 Management eee 16 Basie taus VSS RE EEE Ea e EEE AA DEE EEEE Ee 16 Uia TE EE EE E EE E E E EE E E 17 p gt EEE EE PTE EEO EE EE EE AE ganas AOE EA EE EE 18 A AVG e fm se SS EEE EEE NK 19 PAC UN EE EEE 19 REI EN EE NN ca ER EE E heute sean 19 hege Re SSE EE EE ENE N 21 WAN gs es are EEE 29 FEN 36 TIE EEE EE EE EE NE eee 46 SE 1 EEE EEE NE tes aiend 53 POGHION At Product ueh E
27. IP address of the unit is 192 168 20 1 so first try to open a web browser to this address Also check that your laptop PC is on the same subnet as the router s Ethernet port 3 The router was connected but cannot get back online You may need to enable the periodic ping timer using the System Monitor Link from the Management Console This ensures that if the connection drops i e outage on the network that the router will reboot after so many failed pings and then force a re connect Set the timer to around 15 mins should be sufficient ey Please note The traffic generated by the periodic ping feature is counted as chargeable usage please keep this in mind when selecting how often to ping 4 The router is rebooting frequently Check the System Monitor link in the Administration menu on the management console and see if the Periodic Reset timeout is set to something other than O If it is set to 1 this means the unit will reboot every minute regardless of what happens Reset it to O if you don t want this feature or something quite large if you don t want the router to reboot so often 5 The router has connection but cannot access the internet Check that DNS Proxy is enabled by clicking on the LAN link on the configuration interface Make sure that the DHCP DNS server address 1 IP address is set to the same address as that of the Ethernet port 6 cannot seem to get a 3G WAN connection Click on the 3G Internet Settings link on the
28. Module Model MC8704 Hardware 1 0 Firmware T3 0 2 2AP Mobile Broadband MBB Profile Name Interface Status APN IP Address Profile1 wwan0 Connected telstra internet 10 230 167 160 N Connection Status Provider Telstra Service Type UMTS Frequency WCDMA850 IMEI 357597040030359 Signal Strength dBm 68 dBm High al SIM Status SIM OK N Ethernet Port Status The Ethernet Port on the router can be configured as either a WAN or a LAN port The status of the port is shown here The port can be changed by selecting an option from the drop down list Current LAN means that the Ethernet port is currently operating as a LAN port At this time a computer connected via an Ethernet Cable can access the Internet if connected access connected WiFi devices and access the router itself for configuration Current WAN means thatthe Ethernet portis currently operating as a WAN port Connect your DSL or cable modem to obtain an Internet connection LJ Cd C SS Full CURRENT LAN LAN 4 LAN 3 LAN 2 LAN 1 Ethernet Port ITEM Blid NON System Information Section System Uptime Status P Addras Provider The mobile broadband provider being used to connect to the internet Frequency The frequency band currently in use IME The IMEI International Mobile Equipment Identity of the router a unique code for identifying devices on a cellular GSM network Signal Strength The strength of the mobile broadband signal detected SIM Statu
29. N a aE aaa aaa a a 60 PEC eSSING a CONNEC ed UDB OIE enrestar nin a R E a A E E E EE ETER 60 Using the 3G22WV to make and receive telephone Cala sse ee eee 62 RRG er UI e EE E E S E E A T 62 KAT RS ac H A 0 PRE E E E E E EE EE 62 FOW TOPICE ENE NE EE EEE EE EEE NERE a 62 TN ee 62 Answering an incoming call when on a call EEE EEE EE EE EE 62 Accessing voice mall EE REEE EE EREA NN NN NN EERE RE RAER 62 BEE TI COUE ENE NE ENOUET ERSA 63 Troubleshooting pia pe FUNG HOM ME EE EE EN EE wae 64 AE ee LAN KNE EN 65 FV UN eee EEE EEE EEE 65 spe age ee see OS EE ot a eaet eaters iae TE AEE EEEE DAENT EEEE Oaa ENTOTE 65 FAU ed 66 ret es 010 Pe ONS EE RER RER EE EN 68 Legal amp Regulatory Information sss esse cesse esec eee eee 69 NN 69 NN 69 ETAT OF ON GE 0 EE EEE EE ceamuany T 70 POG eI Ta 71 laaa ea T2 ON 73 3G22WV 3G WiFi Router with Voice User Guide 3 www netcommwireless com E gt NetCommWireless Overview Introduction This manual provides information related to the installation operation and utilisation of the 83G22WV Target Users The individual reading this manual is presumed to have a basic understanding of telecommunications terminology and concepts Prerequisites Before continuing with the installation of your 3G22WV please confirm that you comply with the minimum system requirements below An activated mobile broadband SIM card Computer with Windows Macintosh or Linux based operati
30. NS Server Secondary DNS Server P Please refer to the WAN Failover Backup section on page 29 for information on configuring the WAN failover feature and enabling the Failover notification function FIELD DESCRIPTION Click Apply to save the settings DHCP This connection will get the IP address from the Internet service provider Leave everything as default unless instructed by your Internet Service Provider Internet Settings WAN WAN Configuration WAN Connection Type DHCP Auto config DHCP Mode es Please refer to the WAN Failover Backup section on page 29 for information on configuring the WAN failover feature and enabling the Failover notification function Click Apply to save the settings 3G22WV 3G WiFi Router with Voice User Guide 27 www netcommwireless com E gt NetCommWireless PPPoE Most ADSL ADSL2 services use the PPP over Ethernet protocol Use this protocol if you are utilising a fixed line broadband service especially if the connecting modem is in bridge mode Internet Settings WAN WAN Configuration WAN Connection Type PPPoE KZ PPPoE Mode Usemame Password Verify Password Please refer to the WAN Failover Backup section on page 29 for information on configuring the WAN failover feature and enabling the Failover notification function NAV DESCRIPTION Enter the broadband username as assigned to you by your Internet Service
31. Polic ad E be denied access to the wireless network Reject Reject the specified device s access to the network All other wireless devices not listed will be allowed access to the wireless network Add a MAC address to the filtering list Specify a 12 digit hexadecimal MAC address to add to the MAC filtering list www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide A on FA NetCommWireless WDS Wireless Distribution System The Wireless Distribution system allows the router s network to be expanded using connecting access points that are capable of using WDS mode There are two methods of WDS that can be employed WDS Bridge mode or WDS Repeater mode In both WDS Bridge and Repeater modes the router and all associated access points must use the same Encryption type and encryption key as well as wireless channel frequency Wireless Settings gt WDS MAC address 00 60 64 5C 4A 74 WDS Mode Repeater Mode gt Encrypt Type WPAZ2PSK sharing with the main SSID encryption Encrypt Key OS AP MAC Address 1 AP MAC Address2 AP MAC Address3 AP MAC Address4 Save In WDS Bridge mode the wireless signal of the router and each access point is used as a bridge With 100 of the wireless signal used to link the router and access points this means network access can only be made through Ethernet cable connections Wireless clients will not be able to connect to either the router or access points
32. Provider ISP E as Enter the broadband password as assigned to you by your Internet Service Provider ISP www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 28 E FA NetCommWireless WAN Failover Backup The WAN Failover Backup feature of the NetComm Wireless 3G22WV is designed to provide a backup Mobile Broadband MBB Internet connection in the event your primary Ethernet WAN connection should fail To use this feature you will need both an Ethernet WAN connection from an xDSL modem ISDN Satellite etc and a MBB WAN connection Failover Settings MBB Failower with WAN ping Connection Type failover desc ping failover wwan desc enable MBB connection Destination Address www google com Second Address Periodic PING Timer 3 65535 secs Zs 3 C PING Accelerated 2 65535 secs Fail Count 1 655325 times Success Count 1 1 1 55535 times DESCRIPTION There are four possible options that the WAN Failover Connection Type can be set to MBB Mobile Broadband Failover if WAN link is down If the fixed line connection through the WAN port fails the Mobile Broadband will connect to the internet This is the default settings MBB Failover with WAN ping The 3G22WV sends ping requests to a specified Internet Host to verify whether the Internet connection is online and functioning The Fail Count specifies how many successive ping attempts can fail Connection Type before the 83G22WV
33. Terminal Services Y Microsoft Windows Network To access the files stored on the drive double click on the Disk A link The files on the drive are displayed www netcommwireless com r Disk A on samba 192 168 20 1 File Edit View Favorites Tools Help g I N C 7 Jar Oas O 3 J Search le Folders Address 192 168 20 1 Disk A Folders x Name Fea Folder Sync Size Type Date Modified Desktop Mi file doc 25KB Microsoft Office Wo 17 12 2012 9 57 PM G My Documents Y My Computer E a My Network Places Entire Network 9 Microsoft Terminal Services E IR Microsoft Windows Network 3G22WV 3G WiFi Router with Voice User Guide 60 EO FA NetCommWireless 4 For future easy access map the network drive and assign it a drive letter on your computer by right clicking on Disk A from the folders panel on the left and then selecting Map Network Drive E g Workgroup E W samba 192 168 20 1 Y lt Qa Printer Expand Explore Open Search Open as Notebook in OneNote Make Available Offiine B Add to archive Add to Disk A rar Compress and email Compress to Disk A rar and email Fi Groove Folder Synchronization K 1 amp Combine supported files in Acrobat Map Network Drive K 5 Select a letter to assign the drive and ensure that Reconnect at logon is selected so that after your computer ha
34. Y a given country Network Mode There are 5 modes to select from 11b g mixed mode Both 802 11b and 802 119 wireless devices are allowed to connect to your 3G22WV 11b only Select this if all of your wireless clients are 802 1 1b 11g only Select this if all of your wireless clients are 802 119 11n only Select this if all of your wireless clients are 802 11n 11 b g n Mixed mode Select this if 802 11b and 802 119 and 802 11n wireless devices are in your network This setting configures the frequency that the Wireless Radio uses for wireless connectivity Select one channel that you wish to use from the drop down list Frequency Channel The SSID Service Set Identifier is the name of your wireless network Use a unique name to identify your wireless device so that SSID Network Name you can easily connect to it from your wireless clients This field is case sensitive and can be up to 32 characters long You should change the default SSID for added security Activate this SSID Use this option to disable or enable the use of the SSID Broadcast this SSID This option can be used to hide the wireless broadcasting of the SSID so that only informed parties can connect via wireless Network Authentication See the following pages for an explanation of the different security types available Click Apply to save any changes you make to the settings www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 36
35. a Canberra Melbourne Sydney SIM Security Settings Remember PIN L ves No Next NetCommWireless It is recommended for security purposes that you change the default username and or password Enter a secure username and or password then confirm the password lt gt NetCommWireless Step 2 of 6 Router Security Usesame Password Ate Password Remerber io m ke ode of pour usernann ars p ssword Back Cancel Next Use the radio buttons to turn the Wireless radio on or off When SSID Broadcast is enabled the network name will show up when you do a scan for WiFi networks on your client devices If you disable this you must know the name of the SSID to connect to the wireless network In the SSID Broadcast Name field enter a recognisable name for your network so that you can easily identify it when it comes time to connect wirelessly from a client lt gt NetCommWireless Step 3 of 6 Romer Security Vire WHT nN Go 5510 Broadcast ETE BUENE NIS Broadcast Mame Max 37 characters Ne pmm 2607 NetCommWireless Select the type of wireless security you wish to use with the Network Authentication Type drop down list then enter a security key of at least 8 characters If you choose WPA PSK the WPA Encryption will be TKIP otherwise the router will use AES encryption lt gt NetCommWireless Step 4 of 6 Autor Scanv Bohwork Auibenbtncalicn Trans Srcmily Key Mirren
36. boot the router Administration gt Statistics Memory Memory Total Memory Left WAN LAN WAN Rx Packets WAN Rx Bytes Figure 65 3G22WV 3G WiFi Router with Voice User Guide 59 This page allows you to view the LAN WAN and wireless statistics of your Router This page allows you to view the LAN WAN 3G and Wi Fi wireless statistics 29016 kB 5392 kB Reboot Router www netcommwireless com a FA NetCommWireless Additional Product Information Accessing a connected USB drive USB drives connected to one of the 83G22WV s USB ports may be accessed over the network T Note The 3G22WV supports reading and writing to FAT32 and NTFS formatted drives only To access a USB drive connected to the 3G22WV 3 Open Windows Explorer and in the address bar type 192 168 20 1 then press Enter If you have changed the IP address of the router replace the default IP address with the one you configured for the router The Windows Explorer window changes to show a list of attached devices The screenshot below shows a connected drive listed as Disk A samba 192 168 20 1 File Edit View Favorites Tools Help Q O B P sam E Folder CE G Folder sync Address 4 192 168 20 1 Folders x Name Comments 2 Desktop 2 Disk A My Documents Printers and Faxes Shows installed printers and fax ES 4 My Computer E a My Network Places lt g Entire Network Microsoft
37. cket 25842 Rx Byte 4509151 Tx Packet 36573 Tx Byte 17099083 Name lo Rx Packet 19507 Rx Byte 591917 Tx Packet 19507 Tx Byte 591917 Name ra Rx Packet 1614830 Rx Byte 364955869 Tx Packet 53861 Tx Byte 160309 Name eth2 1 Rx Packet 25342 Rx Byte 4147363 Tx Packet 34725 Tx Byte 15913739 Name eth2 2 Rx Packet 0 Rx Byte 0 Tx Packet 1842 Tx Byte 1091076 Name bro Rx Packet 26033 Rx Byte 4058922 Tx Packet 25652 Tx Byte 15300137 Name wds0 Rx Packet 0 Rx Byte 0 Tx Packet 0 Tx Byte 0 Name wds1 Rx Packet 0 Rx Byte 0 Tx Packet 0 Tx Byte 0 Name wds2 Rx Packet 0 Rx Byte 0 Tx Packet 0 Tx Byte 0 Name wds3 Rx Packet 0 Rx Byte 0 Tx Packet 0 Tx Byte 0 Name wwanOQ Rx Packet 0 Rx Byte 17923 Tx Packet 0 Tx Byte 18933 www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 58 E gt NetCommWireless Logoff The logoff menu option will log the current user out of the web configuration session Administration gt Statistics Memory Memory Total Memory Left WAN LAN WAN Rx Packets WAN Rx Bytes This page allows you to view the LAN WAN and wireless statistics of your Router This page allows you to view the LAN WAN 3G and Wi Fi wireless statistics 29016 kB 5392 kB Figure 64 Logoff Reboot The reboot item will reboot the router This can be useful if you have made configuration changes you want to implement or want to re
38. cm between the radiator amp your body The County Code Selection feature is disabled for products marketed in the US Canada For product available in the USA Canada markets only channel 1 11 can be operated Selection of other channels is not possible www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 72 E gt NetCommWireless Contact Address NETCOMM WIRELESS LIMITED Head Office PO Box 1200 Lane Cove NSW 2066 Australia P 61 0 2 9424 2070 F 61 0 2 9424 2010 E sales netcommwireless com W www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide To www netcommwireless com
39. d MAC IP Port Filter Settings Destination IP Address fF Source IP Address Protocol None Destination Fort Range JU Source Port Range Comment The maximum rule count is 20 Current IP Port filtering rules in system Delet MAC Destination IF Source IP Protocol Destination Port Source Port Adi t Packet HEG Address Address Address ME Range Range MEN ewe Count Otherwise would be accepted L elected Reset Delet iD OPTION Ds NINO MAC IP Port Filtering Default Policy MAC IP Port Filtering Settings MAC Address Destination IP Address Source IP Address Select the port number s protocol type TCP UDP or both If you are unsure use the default TCP amp UDP setting Protocol The destination Port Range of the filter rule If there is only one port involved enter the same port number in both text fields The source Port Range of the filter rule If there is only one port involved enter the same port number in both text fields Action Either accept or drop the packet that matches all of the rule specifications Comment Add a comment to identify the purpose of the rule optional Destination Port Range Source Port Range www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 34 E FA NetCommWireless Content Filtering This page allows you to configure content URL and host filters to restrict improper internet content access from LAN
40. d is greatly affected by the individual installation environment If you have concerns about your network s performance that might be related to range or obstruction factors try moving the computer to a position between three to five meters from the 3G22WV in order to see if distance is the problem Please note While some of the items listed below can affect network performance they will not prohibit your wireless network from functioning If you are concerned that your network is not operating at its maximum effectiveness this checklist may help If you experience difficulties connecting wirelessly between your WiFi Devices and your 3G22WV please try the following steps In multi storey homes place the 3G22WV on a floor that is as close to the centre of the home as possible This may mean placing the 3G22WV on an upper floor TN not to place the 3G22WV near a cordless telephone that operates at the same radio frequency as the 3G22WV 2 3602 Avoid obstacles and interference Avoid placing your 3G22WV near devices that may emit radio noise such as microwave ovens Dense objects that can inhibit wireless communication include Refrigerators Washers and or dryers Metal cabinets Large aquariums Metallic based UV tinted windows If your wireless signal seems weak in some spots make sure that objects such as those listed above are not blocking the signal s path between your devices and the 3G22WWV Cordles
41. d provider coverage maps for more details The total number of WiFi users can also affect data speeds Maximum wireless signal rate and coverage values are derived from IEEE Standard 802 11g and 802 11n specifications Actual wireless speed and coverage are dependent on network and environmental conditions included but not limited to volume of network traffic building materials and construction layout Package Contents The 3G22WV package consists of 3G22WV NetComm Wireless 3G WiFi Router with Voice 12VDC 1 5A Power Adapter 1 x RJ 45 LAN Cable 1 x RJ 11 phone cable Quick Setup Guide Wireless Security Card If any of these items are missing or damaged please contact NetComm Wireless Support immediately by visiting the NetComm Wireless Support website at http Support netcommwireless com Product Features The NetComm Wireless 3G WiFi Router with Voice creates a secure WiFi network providing Internet access for up to 15 users and simultaneous phone service using a mobile broadband network With quick and easy setup the NetComm Wireless 3G WiFi Router with Voice provides a landline experience without the need for fixed line connections Simply plug the NetComm Wireless 3G WiFi Router with Voice into a power outlet then insert an active mobile broadband SIM card into the slot on the rear panel to access a mobile broadband Internet connection within minutes The NetComm Wireless 3G WiFi Router with Voice incorporates a WLAN 802 11b g n access
42. es www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 10 EO FA NetCommWireless Hardware installation Insert your SIM card until you hear a click into the SIM slot For voice functionality connect a standard analogue telephone to the port labelled Voice using the RJ 11 cable provided Connect the power adapter to the Power socket on the back of the 3G22WV Plug the power adapter into the wall socket and switch on the power Wait approximately 60 seconds for the 3G22WV to power up ST NS Connecting via a cable Connect the Ethernet cable provided to any port marked LAN 1 4 at the back of the 3G22W Connect the other end of the yellow Ethernet cable to your computer Wait approximately 30 seconds for the connection to establish Open your Web browser and type http 192 168 20 1 into the address bar and press enter Follow the steps to set up your 8G22WYV After the setup process is completed you will be connected to the Internet SE G Connecting wirelessly 1 Ensure WiFi is enabled on your device computer laptop Smartphone 2 Scan for wireless networks in your area and connect to the network name shown on the included Wireless Security Card 3 When prompted for your wireless security settings enter the Wireless security key shown on the included Wireless Security Card Wait approximately 30 seconds for the connection to establish Open your Web browser and type http 192 168 20 1 int
43. fails over to the Mobile broadband Internet WAN connection while the Success Count specifies how many ping attempts must succeed in order to reset the Fail counter WAN Only Only the WAN port connection is used The Mobile Broadband Connection is disabled effectively disabling the WAN failover function MBB Only Only the MBB connection is used The WAN port connection is disabled There are two possible options that the WAN Failover MBB Connection can be set to Always On Although the router does not use the Mobile Broadband MBB connection when the WAN connection is l available the MBB connection will always be online as a backup connection This allows the router to fail over quickly MBB Connection to the existing MBB connection however may result in MBB carrier charges Dial When Required The router dials the Mobile Broadband MBB connection when the MBB connection is required The router will also automatically disconnect MBB connection if the connection becomes unnecessary Destination Address The address to ping in order to test the status of the internet connection Second Address The alternate address to ping in order to test the status of the internet connection Periodic PING Timer The interval at which a periodic ping request is sent to the destination address or the second address Periodic PING When 4 consecutive pings to the destination and the second address fail the router will send 4 consecutive pings to b
44. from your mobile broadband SIM card enabling you to connect to the applicable mobile service Please verify the APN detected is correct by clicking on the Status tab The current APN will be listed above the SIM Status field Alternatively you can disable the Automatically Configure My Mobile Broadband option and manually enter the APN you would like to use If the Automatically Configure My Mobile Broadband option does not correctly detect your APN and you are unsure of what to enter manually please contact your mobile broadband service provider for more information www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 18 on FA NetCommWireless Advanced Features The basic configuration interface is intended to provide access to all the settings that most people will want to use on their 3G22WV There are advanced settings available if desired which are accessible by viewing the advanced settings pages Home Clicking the Home menu item will return you to the Basic View page Status The status page provides system related information and is displayed when you login to the 3G22WV management console and switch to Advanced View By default the status page will show System Information Mobile Broadband MBB Connection Status and Ethernet Port Status settings All Status LAN Call Forwarding NW System Information System Up Time 00 26 05 Router Version Hardware 0 01 Software V1 1 33 0 Phone
45. g 1004 into the box below and click Start Session lf you don t know which dial string to use please contact your carrier and ask them which dial codes are suitable for network services Session Status Inactive Response from network Send Message Enter USSD dial string here Start Session USSD is a real time messaging service usually utilised to perform mobile account related tasks such as the following Enter the USSD message to be sent in the Send Message field at the bottom of the screen and then click Start Session Checking available credit for a mobile service account Obtaining more credit for a mobile service account Verifying your mobile account information Any responses from your mobile broadband Service Provider will be displayed in the Response from Network box in the middle of the page Please contact your mobile broadband Service provider for a list of available USSD commands for your mobile broadband service www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 30 E FA NetCommWireless Routing Static The Static Route page is used to add or delete static routes Static routes can be used to facilitate communication between devices on different networks Internet Settings gt Routing gt Static Static Routes Item No 1 65535 Only required if you want to edit the existing mapping Destination IP Address 3 IP Subnet Mask
46. ge is from 1 to 65535 Please refer to your TCP UDP based SMS server configuration for which port to use For Example If someone sends a text message and Redirect to TCP is set to 192 168 20 3 and 2002 this text message is stored in the router and forwarded to 192 168 20 3 on port 2002 at the same time Compose This page allows the user to send a new text message to one or multiple recipients Services gt SMS gt New Message Memory amp Message Status Memory Status Total 30 Used0 Free 30 Message Status Inbox0 Outbox 0 Create New Message Destination Number 001 Destination Number 002 61390123399 id Destination Number 003 oO Destination Number 004 oO Destination Number 005 oO Destination Number 006 a Destination Number 007 Di O O Destination Number 008 OD Destination Number 009 O Destination Number 010 Pr OOOO O O Test message to NetComm Wireless Limited Message Body 41 160 Maximum number of characters can vary depending on coding scheme In GSM7 bit mode 160 characters can be sent within a message but the limit changes to 50 characters if the message includes special characters In UCS2 mode most of special character set can be sent but only 50 characters can be sent within a message A new SMS message can be sent to a maximum of 100 recipients at the same time After sending the message the result is displayed next to the destination number as Success in blue or
47. hannels that the router can broadcast on defined by each countries y wireless regulations This feature allows you to isolate clients on your wireless network To enable communication between the wireless clients connected to your NetComm Smart Hub 4G set this option to Disabled To terminate the communication between the wireless clients set this option to enabled The MBSSID AP Isolation function provides isolation among different SSIDs When enabled this function prevents wireless client terminals with different SSIDs from communicating with each other Fragment Threshold Short Preamble Short Slot Tx Burst Pkt_Aggregate AP Isolation MBSSID AP Isolation The Broadcast Service Set Identifier Select Disabled to hide the SSID of your NetComm Smart Hub 4G If disabled other people will not be able scan and detect this product s SSID BSSID WiFi Multimedia WMM Capable er ei at MultiMedia option if enabled supports QoS for experiencing better audio video and voice in WMM Parameters Click on the WMM Configuration button to configure the WMM parameters Multicast to Unicast Converter Multicast to Unicast This function converts multicast data to unicast data and is disabled by default Others HT TxStream This option sets the stream number that wireless antenna transmits HT RxStream This option sets the stream number that wireless antenna receives HT Physical Mode Operating Mode
48. he WWAN section shows the router s WAN IP address 3 Click Login and type admin in the Username and admin in the Password fields without quotes Then click on Submit www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 55 E FA NetCommWireless System Configuration The System configuration page is used to specify an external syslog server or enable the diagnostics function System gt System Configuration Remote Syslog Server IP Hostname PORT L Log to file O Enable O Disable OPTION DEKINITT ION IP Hostname PORT The IP address and port of the external syslog server you would like logging information sent to Log to file Enables or disables the remote syslog server from logging to a file 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 57 E gt NetCommWireless Statistics This page allows you to view the LAN WAN and wireless statistics of your 3G22WV Administration gt Statistics This page allows you to view the LAN WAN and wireless statistics of your Router This page allows you to view the LAN WAN 3G and Wi Fi wireless statistics Memory Memory Total 29016 kB Memory Left 5388 kB VWANILAN WAN Rx Packets 0 WAN Rx Bytes 0 WAN Tx Packets 1842 WAN Tx Bytes 1091076 LAN Rx Packets 26033 LAN Rx Bytes 4058922 LAN Tx Packets 25652 LAN Tx Bytes 15300137 All Interfaces Name eth2 Rx Pa
49. he router s Ethernet subnet You will have to add the routes appropriately in the Static Routes section see Adding Static Routes above xe Please note Some routers will ignore RIP Internet Settings gt Routing gt RIP RIP Routing RIP O Enable Disable Version 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 3 E FA NetCommWireless Click Enable on the RIP Page Select RIP version a Click the Save button NAT The NAT page is used to configure the Network Address Translation rules currently in use on the router The router is in NAT mode by default The NAT configuration settings are also known as Port Forwarding rules Internet Settings Routing gt NAT IP Mapping Settings Item Number 1 65535 Only required if you want to edit the existing mapping Protocol Source IP Address m 9 9 9 Incoming Port Range 1 65535 Destination IP Address S S Destination Port Range bOO tss item Protocol incoming Address Incoming Port Destination Address Destination Port The IP mapping table is empty This is only needed if you need to map inbound requests to a specific port on the WAN IP address to a device connected on the Ethernet interface e g a web camera How to configure Port Forwarding OPTION Bled NON Number to identify the port mapping 1 to as many as needed Specify the protocol to use for the port mapping TCP UDP All protocols Specifies e
50. hentication You may choose from the following wireless security options Disabled Open Shared WPA WPA PSK WPA2 WPA2 PSK WPA PSK WPA2 PSK WPA1 WPA2 802 1x 3G22WWV 3G WiFi Router with Voice User Guide www netcommwireless com ST E FA NetCommWireless WEP WEP Wireless Encryption Protocol helps prevent against unwanted wireless users accessing your 3G22VWV It offers a lower level of security in comparison to WPA PSK and WPA2 PSK Enter the Security Key you would like to use in the WEP Key 1 field SSID and Security Settings SSID Activate this SSID Broadcast SSID Network Authentication WEP Encryption Current Network Key Network Key 1 Network Key 2 Network Key 3 Network Key 4 WPA1 WPA2 NetComm 2607 Enable O Disable Enable O Disable Open Enabled alb2c3d4e5 64 bit HEX ll Enter 10 hexadecimal digits for 64 bit encryption keys or 26 hexadecimal digits for 128 bit encryption keys WPA WiFi Protected Access authentication is suitable for enterprise applications It must be used in conjunction with an authentication server such as RADIUS to provide centralized access control and management It provides a stronger encryption and authentication solution SSID and Security Settings SSID Activate this SSID Broadcast SSID Network Authentication WPA Group Rekey interval RADIUS Server IP Address RADIUS Port RADIUS Key WPA Encr
51. ice Roaming Incoming Call Enable incoming voice calls when utilising a different mobile broadband provider Data Roaming Select to enable or disable data roaming on your mobile broadband connection 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 21 E gt NetCommWireless Band Settings The band settings page enables you to select which frequency band you will use for your connection and enable you to scan for available network operators in your area Internet Settings gt Mobile Broadband gt Band Settings Band Settings This page allows you to set up the frequency band and scan for all the available network operators You can choose an operator manually from the Operator Name List after scanning Current Band All bands Change Band All bands v Apply The default setting of All bands should be appropriate for the majority of users You can also scan for available mobile broadband service providers in your area by selecting Manual for the Current Operator Selection Mode and then clicking the scan button Operator Settings Current Operator Selection Mode Automatic Select Operator Mode Automatic Manual Current Operator Registration Telstra UMTS MCC MNC Operator Status Network Type Scan Apply Operator Name List A list of the detected mobile broadband service carriers in your area will be displayed Select the most appropriate 3G service from the list shown and c
52. imum Data Throughput Up to 21 Mbps downlink HSDPA Cat 14 3G Radio interface Up to 5 76 Mbps uplink HSUPA Cat 6 Antenna connector UFL UFL femaleconnecto 0 connector O 50 degrees Celsius operating temperature Power input 12VDC 1 5A 160 mm L x 195 mm H x 65 mm W Dimensions amp Weight g 362 grams Electrical Specifications A suitable power supply is available on request or via direct purchase from the NetComm Online shop It is recommended that the 3G22WV be powered using the 12VDC 1 5A power supply which is included with the device Environmental Specifications Tolerances The 8G22WV is able to operate over a wide variety of temperatures from UC 50 C ambient 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 65 E FA NetCommWireless FAQ 1 Does the NetComm 3G WiFi Router with Voice require any configuration out of the box No the NetComm 3G WiFi Router with Voice is plug and play device Plug the device into an electrical outlet and once the status indicator lights are on plug in your analogue phone and LAN cable for voice and data connectivity For WiFi connectivity the SSID Service Set Identifier and network key password are located on the bottom of the device If you would like to customize your settings you can enter 192 168 20 1 into your Web browser to access the Management Console and device settings 2 I cannot seem to access the web page interface The default
53. in to the management console and view the status and make changes to your 83G22WV please follow the steps below 1 Open your web browser e g Internet Explorer Firefox Safari and navigate to http 192 168 20 1 or http my router 2 Click the Login tab on the left and enter the username and password configured during the first time setup process then click the Submit button The default username and password is admin if the details haven t been customized Click the Submit button to continue Please Note If you forget the username and password you selected during the 3G22WV set up process holding the reset button for over 10 seconds will restart the unit with the original settings username admin no password 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 15 NetCommWvireless 73 NetCommWireless NetComm Wireless Router Username Password The basic status page provides basic system related information It is shown after logging in to the 3G22WV and can also be accessed by selecting Basic Status from the menu lt gt NetCommWireless NetComm Wireless Router Coverage WCDMA850 Signal Strength dBm 71 dBm High Wireless OD Internet Connection Status Provider APN SIM Status Switch to advanced view The status page shows the 3G Frequency Signal Strength dBm Connection status Current 3G Provider Current 3G APN and the SIM Status E FA NetCom
54. istreat the cord To safeguard the equipment against overheating make sure that all openings in the unit that offer exposure to air are unobstructed WARNING Disconnect the power line from the device before servicing Transport and Hanaling When transporting the 3G22W it is recommended the product be returned in the original packaging This ensures the product will not be damaged In the event the product needs to be returned ensure it is securely packaged with appropriate padding to prevent damage during courier transport 3G22VWWV 3G WiFi Router with Voice User Guide www netcommwireless com 9 a FA NetCommWireless Installation and Configuration of the 83G22WV Placement of your 3G22WV Just like your mobile phone the 83G22WV s location will affect its signal strength to the Mobile Broadband Base Station Cell Tower The data speed achievable from the 3G22WYV is relative to this signal strength which is affected by many environmental factors Please keep in mind that the 3G22WV will need adequate signal strength in order to provide Internet connectivity whilst choosing a location to place your 3G22WV Similarly the wireless connection between your 3G22WV and your WiFi devices will be stronger the closer your connected devices are to your 3G22WV Your wireless connection and performance will degrade as the distance between your 3G22WV and connected devices increases This may or may not be directly noticeable an
55. ither a Friendly IP address that is allowed to access the router or a wildcard IP address of 0 0 0 0 that Source IP Address allows all IP addresses to access the router Incoming Port Range Specify the external port s to listen to Destination IP Address Local Area Network Address of device to forward inbound requests to Destination Port Range Local Area Network Port s to forward connections to 1 Enter the IP Mapping configuration information as appropriate 2 Click Save Please note If the Incoming Port Range specifies a single port as above then the destination port can be set to any port If the Incoming Port Range specifies a range of port numbers then the Destination Port Range MUST be the same as the Incoming Port Range To delete a port forwarding rule click on the corresponding Delete Entry link from the list of IP Mappings www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide o2 E FA NetCommWireless DMZ If you have a client PC that cannot run an Internet application e g Games properly from behind the NAT firewall then you can open up the firewall restrictions to allow unrestricted two way Internet access by defining a DMZ Host The DMZ function allows you to re direct all packets going to your WAN port IP address to a particular IP address in your LAN The difference between the virtual server and the DMZ function is that the virtual server re directs a particu
56. lar service Internet application e g FIP websites to a particular LAN client server whereas DMZ re directs all packets regardless of services going to your WAN IP address to a particular LAN client server Internet Settings gt Routing gt DMZ DMZ Settings DMZ Settings O Enable Disable DMZ IP Address LY OPTION DEFINITION DMZ Settings Enable disable DMZ DMZ IP Address Enter the IP address of a particular host in your LAN Network that will receive all the packets originally going to the WAN port Public IP address of your 3G22W Click Apply to save the above configurations 3G22WWV 3G WiFi Router with Voice User Guide www netcommwireless com 33 E gt NetCommWireless Mac IP Port Filtering This page allows you to setup MAC IP and port filtering rules to protect your network from malicious activity The filtering rules can be used to either allow or block certain users and or ports from accessing the Internet Internet Settings Routing MAC IP Port Filtering This page allows you to view the LAN WAN and wireless statistics of your Router This page allows you to setup MAC IP and port filtering rules to protect your network from malicious activity The filtering rules can be used to either allow or block certain users and or ports from accessing the Internet Basic Settings MAC I IP Port Filtering Default Policy The packet that didnt match with any rules would be Accepte
57. lick Apply The default setting of Automatic should be appropriate for the majority of users and locations www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 22 E gt NetCommWireless SIM Security The SIM Security page enables you to configure SIM PIN related functions such as storing the PIN in use on the SIM or changing the PIN protection status Internet Settings Mobile Broadband SIM Security SIM Security Settings SIM Status SIM OK Number of Retries Remaining 3 Confirm PIN sese Remember PIN Enabled Enable O Disable PIN Protection Enabled ITEM DEKINITTION SIM Status The current status of the inserted SIM Number of Retries Remaining The remaining number of times an incorrect SIM PIN can be entered before being prompted to enter a PUK code Enter the PIN for your SIM card here if required ired Confirm PIN Re enter the PIN for your SIM card here If required Remember PIN Set the 3G22WV to remember the SIM PIN This prevents it needing to be entered each time the 3G22WV starts up PIN Protection Select to enable or disable PIN protection on your SIM card 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 23 E FA NetCommWireless LAN IP Setup The LAN functionality of the 3G22WV can be configured from this page Using this page a user can change the LAN IP LAN Subnet and DNS Masquerading options Internet Settings gt LAN IP Setup
58. mWireless Wireless NetCommbWireless Wiretess VIN VF Network Name SSID Pa S T name Of your persone 0 al 4 L Z 48 4 1 here to display Internet This page allows you to configure basic WiFi settings for this device such as enabling disabling the WiFi functionality changing the Wireless Network Name SSID or the Wireless Security key Wireless WiFi Select the On or Off option to disable or enable the Wireless functionality The SSID Service Set Identifier is the name of your wireless network Use a unique name to identify your WiFi Network Name SSID wireless device so that you can easily connect to it from your wireless clients This field is case sensitive and can be up to 32 characters Enter your chosen Wireless Security key here The default WPA2 PSK key is printed on the wireless security Security key card and on the Product ID on the bottom of the 3G22WV Please note that whilst the key can be customized on this page the key will revert to the default if the 3G22WYV is reset to factory default 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 17 E FA NetCommWireless Internet NEIGOMMT Automatically configure my mobile broadband Mobile Broadband 9 Enable Disable Click here if your service requires a Username and Password Username if required Click here to choose an APH Fl ider identity your moble broadband ser SIM Security Settings
59. mbedded in the device If you have a voicemail messages waiting you will hear an intermittent dial tone on your phone and if your phone has a message waiting indicator light it will be lit www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 66 EO FA NetCommWireless 12 15 16 17 18 la Is the NetComm 3G WiFi Router with Voice secure can other people access my wireless network The NetComm 3G WiFi Router with Voice comes configured with WPA PSK WiFi security enabled When you first access the Internet type 192 168 20 1 into the address bar the wizard will pop up to configure your computer to connect with the security setting please see the Quick Start Guide for more information on connecting your data devices to the NetComm 3G WiFi Router with Voice Only people you allow access to will be able to connect to the NetComm 3G WiFi Router with Voice ensuring your connection is secure and safe Can change the name and password of my wireless network Yes You can change your NetComm 3G WiFi Router with Voice settings from the browser user interface by typing 192 168 20 1 into the address bar of your Web browser You can change the SSID Service Set Identifier security standard WPA WPA2 WEP and your WiFi password How do I share my Internet connection using the NetComm 3G WiFi Router with Voice with other users Provide any users you want to share your WiFi Internet connection
60. nal Call Forwarding P Busy Call Forwarding The status of the Busy Call Forwarding feature which forwards an incoming call if the line is busy No Reply Call Forwarding The status of the No Reply Call Forwarding feature which forwards an incoming call if the call is not answered vere e The status of the Not Reachable Call Forwarding feature which forwards a call if the call cannot connect due to 9 the router Voice settings not responding or blocked www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 20 E FA NetCommWireless Internet Settings Mobile Broadband Connection This page allows you to setup your WWAN Wireless Wide Area Network connection Internet Settings Mobile Broadband Connection Mobile Broadband Profile Settings Profile Name Profle d Automatically configure my mobile broadband Choose an APH here Mobile Broadband Connection Enable Disable Authentication Type cHap Orr Reconnect Delay 30 65535 secs Reconnect Retries jo 1 565535 0 Unlimited Metric 1 85535 MTU 1400 1430 NAT Masquerading Enable O Disable Profile1 Yes Profile No Profile3 No Profiled No Roaming Settings Voice Roaming Outgoing Call O Enable Disable Voice Roaming Incoming Call O Enable Disable Data Roaming O Enable Disable Save OPTION Blid NON Profile Name A name to identify the profile and associated mobile broadband settings Enter the APN name you
61. nd to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiated radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment RF Exposure Information This device meets the government s requirements for exposure to radio waves This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency RF energy set by the Federal Communications Commission of the U S Gover
62. ng systems with a working Ethernet adapter with TCP IP Protocol installed A Web Browser such as Internet Explorer Netscape Navigator Mozilla Firefox Opera Safari etc Wireless Computer System Requirements o Computer with a working 802 116 802 119 or 802 11n wireless adapter Telephony Requirements Standard analogue PSTN or cordless PSTN phone handset DECT with an RJ 11 port ISDN phone handsets are not supported RJ 11 to RJ 11 phone connectivity cable Notation The following symbols are utilised in this user manual The following note requires attention A The following note provides a warning Q The following note provides relevant information www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide A E FA NetCommWireless Product Introduction Product Overview Quad Band HSPA where network is available Up to 21Mbps downlink 5 76Mbps uplink 1 x Voice ports circuit switched 3 x 10 100 LAN Ethernet port 1 x 10 100 1000 LAN WAN Ethernet port for optional alternate Internet connectivity ADSL Cable Satellite 802 11n 300Mbps Wireless Backward compatible with 802 1 1b g 2x Internal WiFi antennas Browser based interface for configuration and management Wireless security options WEP WPA WPA2 2 x USB ports for attaching USB Storage devices to share with connected clients 1 Speeds are dependent on network coverage See your mobile broadban
63. ng text messages to a remote destination can be defined here Forward incoming text messages to the remote TCP destination can be defined here The TCP port which will be used to connect to the remote destination Forward incoming text messages to the remote UDP destination can be defined here The UDP port which will be used to connect to the remote destination Incoming text messages can be redirected to another mobile device and or a TCP UDP message server using the settings listed under the SMS Configuration for Redirection heading Redirect to Mobile You can forward incoming text messages to a different destination number This destination number can be another mobile phone or 3G router phone number To disable the feature simply delete the number in the Redirect to Mobile field and click the Save button www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide DU E FA NetCommWireless For Example If someone sends a text message and Redirect to Mobile is set to 0412345678 this text message is stored on the router and forwarded to 0412345678 at the same time Redirect to TCP amp TCP Port Redirect to UDP amp UDP Port You can also forward incoming text messages to a TCP UDP based destination The TCP or UDP server can be any kind of public or private server if the server accepts incoming text based message The TCP UDP address can be an IP address or domain name The port number ran
64. nment This device complies with FCC radiation exposure limits set forth for an uncontrolled environment In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 20cm 8 inches during normal operation 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 1 E EE gt NetCommVWireless IC Regulations This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada IC Radiation Exposure Statement This equipment complies with IC RSS 102 radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20
65. nnsnnnnnnennnnnnssennneeee 42 Table 29 Advanced View Wireless WDS eee ee eee eee eee 44 Table 30 Advanced View Wireless WPS Settings cesse eee eee eee ee eee eee eee 44 Table 31 Advanced View Wireless Settings Station List Settings rrrrrrrrnnnnnrrnnnnnnrrnnnnnrrnnnnnnrnnnnnnernnnnnernnnnnssensnneee 45 Table 32 Advanced View Services SNMP Settings ee eee 48 PADIS Advanced View NB NN 50 TENNE 53 Table 35 Administration Configuration Items sss sse sees eee eee eee eee 56 Table 36 System Configuration Items sss eee eee ee eee eee eee 57 Table 37 Additional Product Information Call Feature Codes Quick Reference e esse 63 Table 38 Technical Specifications for the 3G22WV ccccccecccssccccesecccsecceuececeecseeuecseeueseeeueeeeueceseueceseueseeenesseeneeees 65 www netcommwireless com 0 8G22WV 3G WiFi Router with Voice User Guide 68 EO FA NetCommWireless egal amp Regulatory Information Intellectual Property Rights All intellectual property rights including copyright and trade mark rights subsisting in relating to or arising out this Manual are owned by and vest in NetComm Wireless Limited ACN 002490486 NetComm Wireless Limited or its licensors This Manual does not transfer any right title or interest in NetComm Wireless s or its licensors intellectual property rights to you You are permitted to use this Manual for the sole purpose of using the NetComm Wireless product
66. nt or in the wireless client utility to start WPS mode Then switch the 3G22WV to WPS mode either by pushing the WPS button on the wireless router or by clicking the Apply button in the web configuration interface Wireless Settings gt WPS WPS Introduction This page allows you to configure WPS WiFi Protected Setup for your Router WPS provides a simple method to establish a secure wireless connection between wireless clients and your Router Once WPS is enabled you will only need to press a button Push Button Mode or enter a PIN PIN Mode on both the wireless client and your Router to enable a secure connection between the two WPS Config WPS Apply Status Not used WPS Configured No SSID NetComm 2607 WPS Auth Mode WPA2 PSK WPS Encrypt Type AES WPS Default Key Index 2 WPS Key ASCII Tamepibiwu PIN 60483089 Reset OOB WPS Progress WPS mode PIN OPTION pin Push Button PBC Press Apply button to begin WPS connection in PIN mode Apply Bled N GN SANE If the wireless security encryption function of this wireless router is properly set you will see a Success message here Otherwise you will see a message in the WPS Status field stating Idle WPS Configured Shows whether WPS is configured or not SSID This is the network broadcast name SSID of the router WPS Auth Mode This field shows the active authentication mode for the wireless connection WPS Encrypt Type This field
67. o the address bar and press enter Follow the steps to set up your 3G22WV After the setup process is completed you will be connected to the Internet To connect additional devices via WiFi repeat steps 1 through 4 0 N OD UI 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 11 NetCommWvireless The first time you connect to the router s IP address via the web browser you are presented with the option to use a setup wizard to helo you quickly get started using your NetComm Wireless Router If you would prefer not to use the setup wizard please proceed to the next section titled Management Console Login Procedure To begin using the setup wizard click the Yes let s get started with the Wizard button Z NetCommWireless NetComm Wireless Router Yes lets get started with the Wizard No thanks take me to the Basic Interface Use the drop down list to select the region you are in for the telephony profile then select the time zone you are in If your SIM card is PIN locked you should also enter the PIN on this screen To save you entering the PIN again later you can set the router to save your SIM s PIN A NetCommWireless Step 1of6 Welcome to the NetComm Wireless Router Set up Wizard This wizard will guide you through the set up of the NetComm W ss Router Please select your Telephony Profile Default Australia New Zealand Please select your Time Zone GMT 10 00 Australi
68. of characters WEA Encryption AES Back f Cancel Nex This page allows you to setup the WWAN Wireless Wide Area Network connection This is the connection to your mobile broadband provider In most cases setting the broadband router to automatically configure your connection will be sufficient but if your carrier has given you specific details to use remove the check from the box and enter the details as provided to you by your carrier lt gt NetCommWireless Step 5 of 6 Mobile Broadband MBH WE YOU 10 Setup pr A iredess Vide Are dion Ender tho raei setengs ok prided by Aulomeatically configure my mobile broadband FE PE EE ee R tig Mobile Broadband EEE Disable i ek mn 1 yont SANAE DELENE User naa ac Passiv Cancel E FA NetCommWireless step 6 A summary of your settings is shown If you need to make any corrections to the settings click the Back button otherwise click the Finish button to begin using your router NetCommUvireless Step 6 of 6 Router installation ks Compete Wizard Please redes your settings and cick finist Tour Router will re sel and sellings wil be saved 025 Telephony Profile WLS Use ee EI eT Lo i BSED Broadcast Hame Back Cancer In Management Console Login Procedure After first time setup the management console will be password protected to prevent unauthorized access to the configuration settings of your 3G22WV To log
69. ogether T Please note In order to activate a conference call you will need to have originated both calls Troubleshooting the Voice Function What do do if have no dial tone Please follow the procedure listed below Check to make sure the phone is plugged into your 3G22WV on either Line 1 port or Line 2 port Check to make sure you are using the correct cable Cat 3 UTP Telephone Cable with RJ 11 plugs Check to make sure the line light on the front panel of the 3G22WV turns solid blue if you lift the handset Check to make sure the blue 3G indication light on the front of the 3G22WW is blinking Check to make sure your 3G SIM card is activated and insert into your 3G22WV properly Check and see if you get the dial tone after rebooting your 83G22WYV OE A have noise interference during telephone calls How can fix this To resolve this issue try the following Verify that the RJ 11 cable is securely connected and not damaged TN to remove any telephone splitters from the connection between your phone and the 3G22W Try rebooting your 8G22WV www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 64 E FA NetCommWireless Technical Data The following table lists the hardware specifications of the 3G22WV MODEL 3G22WV Ralink RT3852 Modem Chipset Module MC8704 UMTS bands Quad band UMTS HSPA HSUPA HSDPA 850 900 1900 2100MHz GSM bands Quad band GSM GPRS 850 900 1 800 1 9OOMHz Max
70. omatically voided if 1 you or someone else use the product or attempt to use it other than as specified by NetComm Wireless Limited 2 the fault or defect in your product is the result of a voltage surge subjected to the product either by the way of power supply or communication line whether caused by thunderstorm activity or any other cause s 3 the fault is the result of accidental damage or damage in transit including but not limited to liquid spillage 4 your product has been used for any purposes other than that for which it is sold or in any way other than in strict accordance with the user manual supplied 5 your product has been repaired or modified or attempted to be repaired or modified other than by a qualified person ata service centre authorised by NetComm Wireless Limited or 6 the serial number has been defaced or altered in any way or if the serial number plate has been removed Limitation of Liability This clause does not apply to New Zealand consumers Subject to your rights and remedies under applicable Consumer Protection Laws which cannot be excluded see Section 3 above NetComm Wireless Limited accepts no liability or responsibility for consequences arising from the use of this product NetComm Wireless Limited reserves the right to change the specifications and operating details of this product without notice If any law implies a guarantee condition or warranty in respect of goods or services supplied
71. on displays all system log messages This option shows extended system log messages with full debugging level details Debug Info This option shows informational messages only This option shows normal system logging information Warning This option shows warning messages only Error This option shows error condition messages only You can also download the current System Log to your computer for off line viewing To do this click the Download Log File link at the bottom of the page 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 53 A FA NetCommWireless Settings The settings page is used to backup or restore the routers configuration or to reset it to factory defaults System gt Settings Save a copy of current settings To save a copy of the router s configuration Key in the administration user Password and click the Save button This will download a copy of the current settings from the router to your PC es Please note The following conditions apply e tis NOT possible to edit the contents of the file downloaded if you modify the contents of the configuration file in any way you will not be able to restore it later e You may change the name of the file if you wish but the filename extension must remain cfg To restore a copy of the router s configuration 1 Click the Browse button 2 Select the configuration file you wish to restore 3 Click the Re
72. on which may be a TCP UDP server or other mobile devices Setup General SMS functionality is enabled by default You can open the Setup page in order to configure additional settings To do this click on SMS and then Setup Services gt SMS gt Setup sms memstbar memory status total 30 used0 free 30 message status Inbox0 Outbox 0 sms gen config sms onoff enable O disable sms numofmsg 20 10 50 sms encoding scheme menu sms gsm7 sms ucs2 sms redir conf sms redir mobile sms redir tcp sms redir serverip sms redir tcp port i pig 1 D n O L n sms redir udp sms redir udp port 165535 sms redir serverip OPTION DEKINITTION General SMS Configuration Memory Status Shows the current number of available and used SMS storage slots available on the SIM Message Status Shows the location of the SMS messages currently stored on the SIM SMS Enable Disable The SMS functionality can be disabled or enabled using this field Messages Page Enter the number of SMS messages to display per page Encoding Scheme The encoding method used for SMS messages Every cellular network has an SMS centre SMSC that handles all SMS message routing and SMSC Address regulates each SMS message according to network traffic demands This address is usually a standard phone number and is essential for SMS functionality with the 3G22WV SMS Configuration for Redirection Forward incomi
73. oth Accelerated Timer destination and second addresses at this interval Fail Count The number of times accelerated pings can fail before the router reboots The number of pings that can succeed before the router returns to periodic pings and does not reboot 3G22WWV 3G WiFi Router with Voice User Guide www netcommwireless com 29 E lt gt NetCommWireless USSD The USSD page is used to send USSD short SMS style messages to the mobile broadband service provider WWAN MBB gt USSD USSD Service Network Messaging also known as Unstructured Supplementary Service Data USSD is a protocol that can be used to communicate from your device to your service provider Depending on which network you use for your mobile broadband service this page can be used for a variety of network services such as balance checking recharging a prepaid service and many others Network messaging can be initiated using special codes specified by your carrier for these various services Once a special code is sent to the network the network responds with the requested information The response often includes instructions for sending additional follow on messages allowing further functionality e g entering credit card information for a credit recharge Please contact your network provider to learn which codes can be used on your network for features such as balance checking recharge etc To begin using this feature please enter the dial string e
74. other call To enable Call Forwarding Busy dial 67 lt Directory Number gt Where directory number is the number you wish to forward calls to Hand up after you hear 2 low pitch beeps To disable Call Forwarding Busy dial 67 Hang up after you hear 2 high pitch beeps To check the status of Call Forwarding Busy dial 67 or view the advanced status page of the management console o Call Forwarding Busy is disabled if you hear 2 high pitch beeps o Call Forwarding Busy is enabled if you hear 2 low pitch beeps Call Forwarding Not Reachable Call forwarding busy will divert all incoming calls to a phone number that you desire only if your telephone is unreachable by the network To enable Call Forwarding Not Reachable dial 62 lt Directory Number gt Where directory number is the number you wish to forward calls to Hang up after you hear 2 low pitch beeps To disable Call Forwarding Not Reachable dial 62 Hang up after you hear 2 high pitch beeps To check the status of Call Forwarding Not Reachable dial 4624 or view the advanced status page of the management console o Call Forwarding No Answer is disabled if you hear 2 high pitch beeps o Call Forwarding No Answer is enabled if you hear 2 low pitch beeps Conference Call This can be achieved by performing a hook flash and then by dialling the third party Wait for the third party to answer your call and then perform another hook flash to conference all the parties t
75. r you the customer and is not transferable 2 the Product Warranty shall not apply to software programs batteries power supplies cables or other accessories supplied in or with the product 3 the customer complies with all of the terms of any relevant agreement with NetComm Wireless Limited and any other reasonable requirements of NetComm Wireless Limited including producing such evidence of purchase as NetComm may require 4 the cost of transporting product to and from NetComm Wireless Limited s nominated premises is your responsibility 5 NetComm Wireless Limited does not have any liability or responsibility under the Product Warranty where any cost loss injury or damage of any kind whether direct indirect consequential incidental or otherwise arises out of events beyond NetComm Wireless Limited s reasonable control This includes but is not limited to acts of God war riot embargoes acts of civil or military authorities fire floods electricity outages lightning power surges or shortages of materials or labour and 6 the customer is responsible for the security of their computer and network at all times Security features may be disabled within the factory default settings NetComm Wireless Limited recommends that you enable these features to enhance your security Subject to your rights and remedies under applicable Consumer Protection Laws which cannot be excluded see Section 3 above the Product Warranty is aut
76. r you are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure If you purchased our goods in New Zealand and are a consumer you will also be entitled to similar statutory guarantees Product Warranty All NetComm Wireless products have a standard one 1 year warranty from date of purchase however some products have an extended warranty option refer to packaging and the warranty card each a Product Warranty To be eligible for the extended 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 69 E FA NetCommWireless warranty option you must supply the requested warranty information to NetComm Wireless Limited within 30 days of the original purchase by registering online via the NetComm Wireless web site at www netcommwireless com For all Product Warranty claims you will require proof of purchase All Product Warranties are in addition to your rights and remedies under applicable Consumer Protection Laws which cannot be excluded see Section 3 above Subject to your rights and remedies under applicable Consumer Protection Laws which cannot be excluded see Section 3 above the Product Warranty is granted on the following conditions 1 the Product Warranty extends to the original purchase
77. r office If this equipment does cause some degree of interference to radio or television reception which can be determined by turning the equipment off and on we encourage the user to try to correct the interference by one or more of the following measures Change the direction or relocate the receiving antenna Increase the separation between this equipment and the receiver Connect the equipment to an alternate power outlet on a different power circuit from that to which the receiver TV is connected Consult an experienced radio TV technician for help 4 The power supply that is provided with this unit is only intended for use with this product Do not use this power supply with any other product or do not use any other power supply that is not approved for use with this product by NetComm Wireless Limited Failure to do so may cause damage to this product fire or result in personal injury Consumer Protection Laws Australian and New Zealand consumer law in certain circumstances implies mandatory guarantees conditions and warranties which cannot be excluded by NetComm Wireless Limited and legislation of another country s Government may have a similar effect together these are the Consumer Protection Laws Any warranty or representation provided by NetComm Wireless Limited is in addition to and not in replacement of your rights under such Consumer Protection Laws If you purchased our goods in Australia and you are a consume
78. range of the wireless signal Connected Time This field shows how long the wireless client has been connected to the router 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 45 E lt gt NetCommWireless Services DDNS The DDNS page is used to configure the Dynamic DNS feature of the router A number of dynamic DNS hosts are offered to select from Services gt Dynamic DNS DDNS Configuration DDNS Configuration Enable O Disable Server Address Verify Password Dynamic DNS provides a method for the router to update an external name server with the current WAN IP address The following DDNS Providers can be configured with the router www dhs org www dyndns org WWW OYns Cx Wwww eaSsydns com www justlinux com www ods org m www tZo com www zoneedit com To configure dynamic DNS 1 Click Enable 2 Select the Dynamic DNS service that you wish to use Enter your dynamic DNS account credentials 3 Click the Save button NTP The NTP page is used to configure NTP Synchronisation or to select the NTP server used for synchronisation Services gt NTP Time Zone Current Time Tue Sep 25 15 29 37 EST 2012 Time Zone Daylight Savings Automatically adjust clock for daylight saving changes NTP Service Enable O Disable NTP Server Address Sae The NTP Network Time Protocol settings allow your router to synchronise its internal clock with a global
79. ration page is used to enable or disable remote administration and set the username password required to access the 8G22WV remotely System gt Administration Firewall Firewall Enable O Disable Enable HTTP D Port 1 65534 Enable Telnet F Enable Ping F Enable SYN cookies Enable SPI firewall Admin Password o000000000 Confirm Password md Username admin Admin Password eecccccece Confirm Password OPTION DEKINITTION Firewall Settings Firewall Use this option to disable or enable the router s firewall Enable HTTP Enable or disable remote HTTP access to the router You can also set the port you would like remote HTTP access to be available on Enable Telnet Select this option to enable the router to be accessed and configured using telnet commands Enable Ping Web User Interface Account Settings Telnet Account Settings Please note The password will only be changed if you enter two matching passwords It is not necessary to change the password if you are only changing the incoming port number To access the router s configuration pages remotely from a remote computer perform the following steps 1 Open anew browser window e g Internet Explorer Firefox Safari 2 Inthe address bar enter the router s WAN IP address and assigned port number e g 10 10 10 10 8080 Please note You can find the router s WAN IP address by clicking on the Status menu The Local field in t
80. re a slight voltage is supplied to an Ethernet connection Blinks on LAN port traffic Powered device connected to the LAN port includes devices with Wake On LAN capability where a slight voltage is supplied to an Ethernet connection Blinks on LAN port traffic ME LO W LAN LAN LAN Powered device computer router connected to the LAN WAN port LAN 1 WAN includes devices with Wake On LAN capability where a slight voltage is supplied to an Ethernet connection Blinks on LAN port traffic Solid blue light when WLAN is enabled Blinks on traffic data transfer Solid amber light when device is powered on Blinking during device Power start up www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 6 on FA NetCommWireless Integrated Interfaces The following integrated interfaces are available at the rear of the 3G22WV INTERFACE FUNCTION Insert your SIM card here until you hear a click Please be careful to insert the SIM in the SIM Slot correct orientation by viewing the printed icon 3G Antenna Connector Attach an optional external 3G Antenna here LAN 4 2 LAN Port for wired Ethernet clients Computers Laptops etc LAN 1 WAN LAN or WAN port for wired Ethernet clients or bridged devices an ADSL modem etc Phone port to enable connection to a standard analogue telephone Power connector connects to a DC 12V 1 5A Power Adapter Hold this button down for over 10 seconds to reset to factor
81. red packet headers making the transmission more efficient The 802 11n protocol uses the Auto Block ACK function for security of the data transmission If a wireless client receives a unicast A MPDU Aggregated MAC Packet Data Unit frame it should respond by sending back an ACK frame without delay A Block Acknowledgement reduces the number of the ACK frames while providing an individual MCS Auto Block ACK acknowledgement of each aggregated data frame l The Decline BA Request function can be set to refuse block acknowledgement requests from wireless clients By default Decline BA Request l TTT this function is disabled 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 41 E gt NetCommWireless MAC Filtering This page allows you to setup MAC address filtering rules to protect your wireless network from malicious activity The filtering rules can be used to either allow or block certain devices or computers from accessing the Internet Wireless Settings gt MAC Filtering Access Policy Please select a SSID number to configure NetComm 2607 Filtering Policy Add a MAC address to the filtering list l O k k ee ee Apply No SSID MAC Address Filtering Policy MAC Filtering Table Empty OPTION Blid NON There are three possible options Disable MAC Filtering is disabled Allow Allow the specified device s access to the network All other wireless devices not listed will Filtering
82. s Phones After considering the above issues if the performance of your wireless network is still impaired and you have a cordless phone Try moving cordless phones away from your 3G22WV and your wireless enabled computers Unplug and remove the battery from any cordless phone that operates on the 2 3GHz band check manufacturer s information If this fixes the problem your phone may be interfering with the 83G22WV If your phone supports channel selection change the channel on the phone to the farthest channel from your wireless network For example change the phone to channel 1 and move your 3G22WV to channel 11 See your phone s user manual for detailed instructions f necessary consider switching to a 900MHz or 5GHz cordless phone Choose the Quietest Channel for your Wireless Network In locations where homes or offices are close together such as apartment buildings or office complexes there may be wireless networks nearby that can conflict with your wireless network Use the Site Survey capabilities found in the Wireless Utility of your wireless adapter to locate any other wireless networks that are available See your wireless adapter s user manual and switch your Router and computers to a channel as far away from other networks as possible Experiment with more than one of the available channels in order to find the clearest connection and avoid interference from neighbouring cordless phones or other wireless devic
83. s The status of the SIM card that is currently inserted into the router LAN port Mode The LAN1 port can also operate as a WAN port for connecting to a bridged Ethernet device such as an xDSL modem Using the pull down menu in the Ethernet Port Status section select the LAN1 mode applicable for your environment To view the LAN PPPoE or Call Forwarding status click on the relevant link below the green menu bar Each of these sections is hidden by default To view them all click on the All Status button Each section contains a breakdown of information relevant to the connection type or function 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 19 E gt NetCommWireless M LAN IP 192 168 20 1 255 255 255 0 MAC Address 00 60 64 5C 4A7A ITEM Blid NON ip The IP address and subnet mask of the router is displayed here MAC Address The MAC address of the router is listed here N Call Forwarding Status Call Waiting Disabled Unconditional Call Forwarding Disabled Busy Call Forwarding Enabled 61101 No Reply Call Forwarding Enabled 61101 Not Reachable Call Forwarding Enabled 61101 ITEM DEKINITTION Call Waitin The status of call waiting which is a feature is allowing the user to Suspend a current telephone call and switch 9 to a new incoming call a l The status of the Unconditional Call Forwarding feature which forwards an incoming call to another number in Unconditio
84. s been restarted your drive will still be available Click Finish Map Network Drive 3G22WV 3G WiFi Router with Voice User Guide 61 Windows can help you connect to a shared network folder and assign a drive letter to the connection so that you can access the folder using My Computer Specify the drive letter for the connection and the folder that you want to connect to Example server share Reconnect at logon Connect using a different user name Sign up to 192 168 20 1 Z t dr P Search IS Address ES Z Folders x 2 Desktop ES My Bocuments E i My Computer E Se Windows XP C _ Y ILN ar LE HH R E co SP Disk A on samba 192 168 20 1 Z ES GF Control Panel www netcommwireless com E FA NetCommWireless Using the 3G22WV to make and receive telephone calls The 3G22WV provides circuit switched voice services via two telephony line interfaces offering the ability to make and receive telephone calls via a regular analogue telephone using the 3G mobile network T Please note Please refer to your mobile service provider for activation of your voice service and information about the call charges that apply It s important to note that the 3G22WV has two separate line interfaces that share a single outbound inbound telephone line This means that handset s connected via one port will not be able to use the line at the same time as handsets connected via the other port
85. s been emptied Jan 24 11 15 43 NetCemm Wireless Router user notice flush conntradt cache flushing conntrack cache Jan 24 11 15 42 NetComm Wireless Router user notice route template flushing conntrad cache Jan 24 11 15 42 NetComm Wireless Router user notice route template 0 0 0 0 10 187 77 241 0 0 0 0 UG 20 0 0 wwand Jan 24 11 15 42 NetCamm Wireless Router user notice route template 239 0 0 0 0 0 0 0 255 0 0 0 U 0 0 0 bd Jan 24 11 15 42 NetGomm Wireless Router user notice route template 192 168 1 0 0 0 0 0 255 255 255 0 U 0 0 0 b Jan 24 11 15 42 NetComm Wireless Router user notice route template Destination Gateway Genmask Flags Metric Ref Use face Jan 24 11 15 42 NetComm Wireless Router User not oe route template Kernel IP routing table Jan 24 11 15 42 NetGomm Wireless Router user notice route template new routing table Jan 24 11 15 42 NetGomm Wireless Router user notice route template skipped trigger Jan 24 11 15 42 NetComm Wireless Router user notice route template reading configuration service router staticroute trigger Jan 24 11 15 42 NetComm Wireless Router user notice route Iern plate adding new static route table Download Log File The System Log enables you to troubleshoot any issues you may be experiencing with your router Selecting the appropriate logging level will show you either informational messages about your router or every message produced when All is selected ITEM De NON All This opti
86. s number to the called party s telephone equipment when the call is being set up but before the call is answered Where available caller ID can also provide a name associated with the calling telephone number To force Caller ID to be blocked for an outbound call dial 4314 followed by the number you wish to dial To force Caller ID to be unblocked for an outbound call dial 314 then follow the dialling number Call Waiting Call waiting allows for indication and answering of an incoming telephone whilst an existing call is underway To disable call waiting dial 43 and hang up after you hear 2 high pitch beeps To enable call waiting dial 48 and hang up after you hear 2 low pitch beeps To check the status of Call Waiting dial 43 or view the advanced status page of the management console o Call waiting is disabled if you hear 2 high pitch beeps o Call waiting is enabled if you hear 2 low pitch beeps Call forwarding or call diverting is a feature that allows an incoming call to be redirected to another number depending on the circumstances at the time of receiving the call Please note The Call Waiting feature will automatically turn off if you enable Call forwarding Call Waiting will need to be enabled again after Call Forwarding is disabled Call Forwarding Unconditional Call forwarding Unconditional will divert all incoming calls to a phone number that you desire To enable Call Forwarding Unconditional dial
87. s the Web user interface you will need to reset your NetComm 3G WiFi Router with Voice back to default settings To reset your device press and hold the reset button on the back of your NetComm 3G WiFi Router with Voice for 10 15 seconds all the indicator lights on the unit will flash when your device is reset After a reset the default WiFi settings SSID and WPA key can be found on the base of your NetComm 3G WiFi Router with Voice Note this will also reset any custom settings and passwords you may have already set up Can use the NetComm 3G WiFi Router with Voice overseas No The NetComm 3G WiFi Router with Voice is not equipped for international roaming or data services If you require the capability to call international locations please speak with your 3G service provider to enable international calling on your NetComm 3G WiFi Router with Voice 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 6 7 E FA NetCommWireless Appendix A Tables TETEN 2 Table 2 LED ore CAUONS La 6 TEN enn ne RU a en E oe ep ee eee oe eee ene ee 7 TVETEN 8 Table 5 LAN Management Default Settings sees eee eee eee eee eee 8 Table G lt WAN Port Default Settings a a 02T T nET T RAT TERA adana a EAT aida Ea eaZ ERER REHAT riv 8 Be Ve EEE WIR Default PID gear ane ne en oe ee nT Te SP EEE EE 8 Table 8 Web Interface Default Settings sese eee ee eee eee 8 Table 9 Basic View WIFI NNN 17 Table 10 Basic View Interne
88. splay or collect data from the 3G22WV that can be sent to a network management system so that the 3G22WV can be monitored for conditions that require administrative attention Various system information including interface statistics uptime and memory usage are available when viewed with an appropriate SNMP trap monitor Services gt SNMP SNMP Configuration Enable SNMP Enable O Disable Read Only Community Name public Read Write Community Name Download Poia ES This is a brief version of the MIB file only Trap Destination IP Address Heartbeat Interval seconds 43200 Trap Persistence Time seconds Ei Trap Retransmission Time seconds 21600 OPTION DEFINITION Enable SNMP Use this field to switch on the SNMP functionality Read Only Community Name The default name to identify the router with read only privileges is public This name can be changed to further identify the router from other network devices The default name to identify the router with read and write privileges is private This name can be changed to further Read Write Community Name identify the router from other network devices Download MIB File Use the download link to obtain a copy of the Management Information Base MIB file for the 3G22WV This file contains all the available SNMP identifying objects for each module that the 3G22WV uses www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 48 3G22WV
89. ss every Periodic Ping Accelerated Timer seconds 4 Ifall accelerated pings in step 3 above fail the number of times configured in Fail Count the router reboots 5 If any ping succeeds the router returns to step 1 and does not reboot Please note The Periodic Ping Timer should never be set to a value less than 60 seconds this is to allow the router time to reconnect to the cellular network following a reboot How to Disable the Periodic Ping Monitor To disable the Periodic Ping Reset Monitor simply set to Fail Count O I Please note The traffic generated by the periodic ping feature is counted as chargeable usage please keep this in mind when selecting how often to ping How to configure a Forced Reset Also known as an automatic reboot this facility can be configured to automatically reboot after a period of time specified in minutes While this is not necessary it does ensure that in the case of remote installations it will reboot the router if some anomaly occurs This feature is available by clicking on the Services menu followed by the System Monitor menu item on the right The default value is 0 which disables the Forced Reset Timer The maximum value is 65535 minutes 1092 5 hours or 45 5 days 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 47 E FA NetCommWireless SNMP The Simple Network Management Protocol SNMP feature can be used to di
90. store button To restore the router s configuration to the factory defaults Click the Restore button to restore the router to factory default settings The router will then restart with the factory default configuration loaded www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 54 E FA NetCommWireless Update Firmware This page allows you to upgrade the 3G22WV s internal software To upgrade the firmware of your 3G22WV you need to download the upgrade image file to your local hard disk and then click the Browse button and navigate to the location of the firmware file on your computer Once you have selected the new firmware file click Apply to start the upgrade process System gt Update Firmware Update Firmware This page allows you to upgrade your Routers firmware Click on Browse to locate the firmware file to be used for the upgrade Please note that it takes approximately 4 minutes for the firmware to be upgraded DO NOT turn off your Router during the firmware upgrade process Apply The upgrade process takes several minutes During the firmware upgrade process all the lights on the front of the 83G22WYV will flash Do not interrupt the power supply during the upgrade process Once completed follow the on screen prompts and your 3G22WV will restart 3G22WWV 3G WiFi Router with Voice User Guide www netcommwireless com 55 E gt NetCommWireless Administration The Administ
91. t Settings EEE EEE NE 18 Table 11 Advanced View Status SN Sn 19 Table 12 Advanced Status LAN Status Settings ccccccssseressseresasssecavasecavacecacscseuerenauasenavasenavasacavacacacscseuerenauarans 20 Table 13 Advanced Status Call Forwarding Settings sse sees eee eee eee e eee 20 Table 14 Advanced View Internet Settings Mobile Broadband Connection Settings sss sees eee eee eee ee eee 21 Table 15 Mobile Broadband SIM Security Settings sse eee eee eee eee 23 FRETTEM 24 Table 17 Internet Settings LAN Advanced Settings ccccssccccssseccecssccecesececeeeceeeeeseceseeseceseeuecesseneceesausecetseneses 26 Table 18 Advanced View WAN Settings Static lD eee eee ee eee eee 27 Table 19 Advanced View WAN PPPoE Mode Settings sse sees eee eee ee eee eee 28 Table 20 Advanced View WAN Failover Settings eee eee eee eee ee eee eee eee 29 Fe 2 Le NAT OPNE 32 RMN 33 Table 23 Advanced View Services MAC IP Port Filtering sese eee eee eee 34 Table 24 Advanced View Services Routing Content Filtering esse sees eee eee ee eee eee e eee eee 35 Table 25 Advanced View WiFi Settings cesses eee ee eee eee ee eee eee 36 Table 26 Advanced View WiFi Security Settings eee eee ee eee eee ee eee eee 37 Table 27 Advanced View Advanced Wireless Settings sse sees eee eee eee 41 Table 28 Advanced View Wireless MAC Filtering rrrrrnrrrrnnnnrrrnnnnrrrnnnnnerrnnnnnrrnrnnnrrnnnnnevnnnnnnennnn
92. to be assigned to the computer or device Click Save a a DHCP Relay Configuration To relay the DHCP function from a remote DHCP server select the DHCP Relay Configuration link at the top of the page DHCP Relay O Enable Disable DHCP Server Address fos 1 Set the DHCP Relay option to Enable 2 Enter the IP Address of the DHCP Server you wish to relay to and press the Save button 3G22WV 3G WiFi Router with Voice User Guide www netcommwireless com 25 E FA NetCommWireless LAN Advanced Setup The Advanced Setup LAN page has settings that should only be configured by experienced administrators The following page provides a brief overview of the features available Internet Settings gt LAN gt Advanced Setup Advanced Setup 802 1d Spanning Tree LLTD IGMP Proxy UPnP Router Advertisement PPPoE Relay DESCRIPTION The default is Disable select Enable to enable this option The Spanning Tree 802 1d Spanning Tree protocol is used to stop loops when using wireless distribution system WDS links as redundant links in a distribution system LLTD This field is the Link Layer Topology Discovery LLTD protocol The default setting is Disable Select Enable to enable this option IGMP Prox The field is the Internet Group Management Protocol IGMP protocol The default y setting is Disable Select Enable to utilise this feature The default option Universal Plug and
93. to which it relates Otherwise no Dart of this Manual may be reproduced stored in a retrieval system or transmitted in any form by any means be it electronic mechanical recording or otherwise without the prior written permission of NetComm Wireless Limited NetComm and NetComm Wireless is a trademark of NetComm Wireless Limited All other trademarks are acknowledged to be the oroperty of their respective owners Customer Information The Australian Communications amp Media Authority ACMA requires you to be aware of the following information and warnings 1 This unit may be connected to the Telecommunication Network through a line cord which meets the requirements of the AS CA S008 2011 Standard 2 This equipment incorporates a radio transmitting device in normal use a separation distance of 20cm will ensure radio frequency exposure levels complies with Australian and New Zealand standards 3 This equipment has been tested and found to comply with the Standards for C Tick and or A Tick as set by the ACMA These standards are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio noise and if not installed and used in accordance with the instructions detailed within this manual may cause interference to radio communications However there is no guarantee that interference will not occur with the installation of this product in your home o
94. with the SSID Service Set Identifier and WiFi network password for your NetComm 3G WiFi Router with Voice Each user will need to select the NetComm 3G WiFi Router with Voice SSID on their WiFi enabled computer or device and enter the network password you provide What is the difference between upload and download speeds and why do they differ Upload is when you send information e g emails from your computer and download is when you receive information via the Internet The speeds at which upload and download operate depend on the way you use the Internet and the size of files you send and receive Do I need to attach an antenna on this device Yes Your NetComm 3G WiFi Router with Voice comes equipped with an antenna you need to attach the 3G antenna to get the 3G signal have lost the security card that came with the setup instructions What can do If you have lost your security card and forgotten the wireless security details SSID and WiFi network password there is a label stuck to the base of your NetComm 3G WiFi Router with Voice with all your original security details If the label is unreadable or has been removed the WiFi network password can be viewed or reset by logging in to the Management Console using an Ethernet Cable connected to the LAN port of the NetComm 3G WiFi Router with Voice forgot my Management Console password What can I do If you have forgotten your Management Console password and cannot acces
95. y Code AP Isolation MBSSID AP Isolation BSSID WiFi Multimedia WMM Capable Multicast to Unicast Converter Multicast to Unicast Others HT Tx Stream HT Rx Stream HT Physical Mode Operating Mode Channel BandWidth Guard Interval MCS Reverse Direction Grant RDG Aggregation MSDU A MSDU Auto Block ACK Decline BA Request sec range 60 600 default 300 ms range 20 999 default 100 2 ms range 1 255 default 1 00 60 64 5C 4A 34 O Enable Disable WMM Configuration O Enable Disable O Mixed Mode Green Field 20 020 40 Long Auto O Enable Disable O Enable Disable O Enable Disable O Enable Disable Apply For details on the advanced wireless settings page please see the table on the following page www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 40 EO gt NetCommWireless OPTION DANION l A mechanism to enable the router to communicate with older legacy wireless network adapters that use 802 11b and BG Protection Mode 802 11g wireless protocols Client Idle Timeout The wireless client connections will timeout if there is no data packets transmitted within the specified seconds range Beacon Interval Data Beacon Rate DTIM SEP a value Deuce 1 and 209 ior the Delivery Traffic naication Message DTIM A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages This specifies
96. y defaults 3G22WWV 3G WiFi Router with Voice User Guide www netcommwireless com F E FA NetCommWireless Physical Dimensions The following page lists the physical dimensions of the 83G22WV SEPP DIMENSIONS Length Width 65 mm 250 grams 3G22VWV Default Settings The following tables list the default settings for the 3G22W LAN MANAGEMENT Static IP Address 192 168 20 1 Subnet Mask 255 255 255 0 Default Gateway 192 168 20 1 WAN INTERNET Disabled operates as LAN by default WIRELESS WIFI SSID refer to the included Wireless Security card WPA2 PSK Security Key refer to the included Wireless Security card 3G22WV WEB INTERFACE ACCESS Username admin Password admin www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 8 on FA NetCommWireless safety and Product Care With reference to unpacking installation use and maintenance of your electronic device the following basic guidelines are recommended To avoid fire or shock hazard do not use or install this product near water For example near a bathtub kitchen sink laundry tub or near a swimming pool Also do not expose the equipment to rain or damp areas e g a wet basement Do not connect the power supply cord on elevated surfaces Allow it to lie freely There should be no obstructions in its path and no heavy items should be placed on the cord In addition do not walk on step on or m
97. yption WPA PSK WPA2 PSK NetComm 2607 Enable O Disable Enable O Disable WPA1 WPA2 v 0 0 0 0 1812 AES A newer type of security is WPA PSK TKIP and WPA2 PSK AES This type of security gives a more secure network compare to WEP Use TKIP Encryption Type for WPA PSK and AES for WPA2 PSK After that please enter the key in the Passphrase field The key needs to be more than 8 characters and less than 63 characters and it can be any combination of letters and numbers Please note that the configuration for WPA PSK and WPA2 PSK is also identical SSID and Security Settings SSID Activate this SSID Broadcast SSID Network Authentication WPA Pre Shared Key WPA Group Rekey interval WPA Encryption fn NetComm 2607 Enable O Disable Enable O Disable WPA PSK WPA2 PSK Click here to display S ey Your 8G22WV uses WPA2 PSK by default Check your Wireless Security Card or the device label on the bottom of the 8G22WV for your default SSID and Security key to begin connecting your wireless devices www netcommwireless com 3G22WV 3G WiFi Router with Voice User Guide 38 E FA NetCommWireless 802 1x In order to use 802 1X security you need to have a RADIUS server on your network that will act as the authentication server Please type in the details for your RADIUS server in the fields required SSID and Security Settings SSID Activate this SSID Enable O Disable

3G22WV User Guide

Contents

Download Pdf Manuals

Related Search

Related Contents