. AJA_manual_FR1andFR2.fm
Contents
1. 5 Volts PS1 ej 2 Ground el3 Pin Numbers Serial Com Port 4 Serial Com Port 15 Ground 6 6 5 Volts PS2 e 7 6 5 Volts PS1 8 Pinout for RJ45 Connector On Rear Panel2. from the frame or directly to BNCs on the module s corresponding cell group the 9 BNCs on the rear panel See the Note below for more information on looping reference inputs in the cell group FRI Frame the external reference signal is distributed passively to all frame modules Cards installed in the frame should have FRAME reference selected and one and only one card in the frame should have TERMINATION set to ON All other cards in the frame should have TERMINATION set to OFF FR2 Frame the external reference signal is distributed by an in frame distribution amplifier to all frame modules This system terminates the Frame Reference input BNC and buffers the signal to all slots Cards installed in the FR2 frame should have FRAME set for reference select and all cards should have TERMINATION set to OFF Note Each cell group of 9 BNCs contain two BNCs that can be used for a looping reference connection for the corresponding card module If this method is used then the reference select setting on that module should be set to LOOP and the TERMINATION setting on the module should be set to OFF no termination Optionally if youre using only one of the looping reference BNCs then the TERMINATION setting should be set to Power Supply Monitoring RJ45 Port standard RJ45 10BaseT style connector offers access for monitoring power supply voltages see pinout at back of manual AC Pow
3. FR1 and FR2 Video Card Frames User Manual AJA AJA VIDEO SYSTEMS INC August 25 2003 P N 101642 00 AJA AJA VIDEO SYSTEMS INC Trademarks Notice AJA Io and Kona are trademarks of AJA Video Inc All other trademarks are the property of their respective holders Copyright 2003 AJA Video Inc All rights reserved All information in this manual is subject to change without notice No part of the document may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying or recording without the express written permission of AJA Inc FCC Emission Information This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by AJA Video can effect emission compliance and could void the user s authority to operate this equipment Conta
4. cting Support Limited Warranty To contact AJA Video for sales or support use any of the following methods 443 Crown Point Circle Grass Valley CA 95945 USA Telephone 1 800 251 4224 or 1 530 274 2048 Fax 1 530 274 9442 Web http www aja com Support Email support aja com Sales Email sales aja com When calling for support have all information on the product serial number etc at hand prior to calling AJA Video warrants that this product will be free from defects in materials and workmanship for a period of five years from the date of purchase If a product proves to be defective during this warranty period AJA Video at its option will either repair the defective product without charge for parts and labor or will provide a replacement in exchange for the defective product In order to obtain service under this warranty you the Customer must notify AJA Video of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service The Customer shall be responsible for packaging and shipping the defective product to a designated service center nominated by AJA Video with shipping charges prepaid AJA Video shall pay for the return of the product to the Customer if the shipment is to a location within the country in which the AJA Video service center is located Customer shall be responsible for paying all shipping charges insurance duties taxes and any other charges f
5. disconnected before installing the FRI or FR2 frame modules into the frame or installing and removing options If a mains switch is not provided the power cord s of this equipment provide the means of disconnection The socket outlet must be installed near the equipment and must be easily accessible Caution FR2 Dual Power Cord Notice please read this To reduce the risk of electrical shock disconnect both power cords before servicing equipment Warning The front fan door is heavy and is not hinged Remove with Caution Introduction The AJA FRI and FR2 are multiple card frames that support both AJA s R series video card modules and other industry standard modules They bring high density packaging high capacity power supplies and forced fan cooling to your rack so you don t need to reserve space above or below the frames Model FR1 The FR1 frame offers space for four modules in a 1 RU space AJA s own R5 and R20 modules fit into the frame as well as industry standard modules Color black reference can be connected at a rear panel BNC for distribution passively to all frame modules Model FR2 The FR2 frame provides greater space housing up to ten modules in a 2 RU space Like the FR1 the FR2 supports both AJA s own R series modules as well as industry standard modules Color black reference in the FR2 is also distributed to all modules but it s actively distributed rather than passive Optional redundant power supplies ar
6. e available for the FR2 frame and all power supplies are easily hot swapped from the front of the unit one screw on the rear panel must be removed on each prior to removal E AJA AJA VIDEO SYSTEMS INC Features The FR1 and FR2 frames offer a variety of unique features for easy connectivity and ease of installation in any environment FRI and FR2 Frames FR1 Features e Dual fan forced air cooling e Optional redundant power supply diode isolated e Universal power supply is auto ranging from 90 to 260 VAC with 40 Watts capacity e 4 module slots cells e Each module cell is provided with 9 BNC inputs or outputs e Single frame reference BNC distributes passively to all cells e Remote power supply monitoring via RJ45 port on rear panel e Power LEDs on front panel show power status e Compatible with common industry frames video cards only Leitch 6800 series FR2 Features e Triple fan forced air cooling inside removable access door e Hot swappable power supplies e Optional redundant power supplies diode isolated e Universal power supply is auto ranging from 90 to 260 VAC with 100 Watts capacity e 10 module slots cells e Each module cell is provided with 9 BNC inputs or outputs e Single frame reference BNC distributes actively to all cells via an internal distribution amplifier e Remote power supply monitoring via RJ45 port on rear panel e Power LEDs on front panel show power status e Compatible with common industr
7. er Connectors 2 female The FR1 has one AC power connection socket and the FR2 has two one for each of its power supplies My Power LEDs 2 The PS1 and PS2 LEDs on the FR1 FR2 front door indicate which if any power _ supply is currently powered up and supplying power to the frame modules You can tell at a glance if a supply is powered up and functional by its associated 1 LED Note If the front door is removed while power is applied the fans in the front door and the power monitoring LEDs will not operate until the door is replaced AJA FR1 and FR2 User Manual Installation Installation Typically installation consists of the following 1 disconnect power from the frame remove line cord remove the FR1 FR2 front panel install AJA R series or other industry standard card modules apply external color black reference at the frame s External Reference BNC Wom WwW N apply power to the frame by connecting a north american style power cord from the frame to mains power 90 to 260 VAC Please follow all manufacturer s instructions for the video cards being installed noting any cautions or special instructions Instructions for removing the front door for module installation and power supply exchange removal FR2 only are provided in the following discussions Front Door To remove the front door firmly grasp both removal knobs and rotate them in opposite Removal directions Hang on t
8. lsolated Cooling Dual fan forced air FR2 Specifications AJA FR1 and FR2 User Manual Specifications Item Specification Physical Dimensions Width 19 Height 1 75 Depth 14 75 Rack Units 1 Compatibility Leitch 6800 series Options FR1 PS Power Supply Module for FR1 Frame Models FR1 FR1 frame with one power supply FR1 D FR1 frame with two redundant power supplies Certifications UL CSE and CE certifications Item Specification Capacity 10 slots 2 Rack Units Inputs Group of 9 BNCs I O for each module 10 groups e Reference Input BNC active DA to all slots Power 100 Watt Capacity Universal Input 90 240 VAC Power Supply Optional Redundant Power Supply Diode Isolated Cooling 3 fan forced air Physical Dimensions Width 19 Height 3 5 Depth 13 Rack Units 2 Compatibility Leitch 6800 series Options FR2 PS Power Supply Module for FR2 Frame Models FR2 FR2 frame with one FR2 PS power supply FR2 D FR2 frame with dual power supplies FR2 PS FR2 Power supply Certifications UL CSE and CE certifications AJA AJA VIDEO SYSTEMS INC FR1 FR2 Power The power supply outputs can be monitored via the RJ45 connector on the rear panel The Monitoring following diagram shows the pinouts where supply values can be measured Description RJ45 Connector on Rear Panel 6 5 Volts PS2 i 6
9. o the knobs so that as the door releases you can hold on to the door and Installation remove it without it falling off Caution fyou dont hang on to the front door knobs as the door is removed from the frame the door could fall and become damaged or cause injury Power Supply To remove an FR2 power supply follow these steps Removal FR2 1 2 Locate which of the two supplies you wish to remove On the rear panel remove the strain relief screw that secures the power supply to the frame saving the screw Remove the frame front panel door as explained earlier 3 From the front of the frame grasp the two pull handles on the front of the desired power supply and gently pull it out of the frame Installation of a new supply is the reverse of this removal procedure E AJA AJA VIDEO SYSTEMS INC Rear of FR2 Panel Remove screw from desired supply Front of FR2 Panel Door Removed Grasp Supply By Its Handle and Pull Out FR2 Power Supply Removal Note FR1 power supply replacement requires disassembly of the chassis frame It is not user serviceable power supply replacement should be referred to a qualified AJA service center Specifications FR1 Specifications Item Specification Capacity 4 slots 1 Rack Unit Inputs Group of 9 BNCs I O for each module 4 groups e Reference Input BNC Power 50 Watt Capacity Universal Input 90 120 VAC Power Supply Optional Redundant Power Supply Diode
10. or products returned to any other locations This warranty shall not apply to any defect failure or damage caused by improper use or improper or inadequate maintenance and care AJA Video shall not be obligated to furnish service under this warranty a to repair damage resulting from attempts by personnel other than AJA Video representatives to install repair or service the nn fe b to repair damage resulting Pom improper use or connection to incompatible equipment c to repair any damage or malfunction caused by the use of non AJA Video parts or supplies or d to service a product that has been modified or integrated with other products when the effect of such a modification or integration increases the time or difficulty of servicing the product THIS WARRANTY IS GIVEN BY AJA VIDEO IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED AJA VIDEO AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AJA VIDEO S RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE WHOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER AJA VIDEO OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES AJA FR1 and FR2 User Manual Important Safety Information Important Safety Information For North American Customers this unit ships with a 120 VAC style AC plug connector Caution Ensure Mains Power is
11. y frames video cards only Leitch 6800 series AJA FRI and FR2 User Manual I O Connections ea I O Connections Power Supply Sockets For Line Cords Frame Reference RJ45 J39 J29 J19 J9 FRI Multiple Card Frame Rear Panel Connectors Power Supply Sockets For Line Cords K oo a a 2 o 3 98 HF RJ45 Cell 10 Cell9 Cell8 Cell7 Cell6 Cell5 Cell4 Cell3 Cell2 Cell1 J91to J8ito J71to J6ito J51to J41to J31to J21to J1i1to J91to Power J99 J89 J79 Jeo J59 J49 J39 J29 J19 J9 Supply Relief Screws must remove to replace supply FR2 Multiple Card Frame Rear Panel Connectors AJA AJA VIDEO SYSTEMS INC User Controls Input Output BNCs groups of 9 per cell Each unique slot in the FR1 FR2 frames connect to a group of 9 BNCs on the frame rear panel The actual function of the BNC connectors is dependent on the video card installed Each group of 9 BNCs corresponds to the card installed in the same position for example the right most card connects to the right most group of connectors at the position on the rear panel Frame Reference BNC Both the FR1 and FR2 frames have this frame reference input BNC connector which feeds an external reference video signal to all modules installed in the frame How the signal is distributed differs for the FR1 and FR2 frames Additionally individual modules can usually be strapped as to whether external reference is distributed
Download Pdf Manuals
Related Search