Home

Instructions

1. ikelite logo will be facing forward toward the front of the camera housing 5 With your free hand insert and rotate the 1 4 20 X 5 8 screw clockwise until threaded into the housing mount Finish tightening the tray firmly to the housing using a flathead screwdriver Note The Housing Tray is designed for Ikelite Housings so excessive pressure applied to either side of a Non lkelite housing may cause the housing to rotate slightly on the Tray Diagram D Protective Backing i peel off before use m 1 P Diagram E z N Fai Customer Support Ikelite Underwater Systems Service Department 50 West 33rd St Indianapolis IN 46208 USA Email ikelite ikelite com Phone 317 923 4523 Limited Warranty This Ikelite product is warranted against any manufacturing defects for a period of one 1 year from the original date of purchase Defective products should be returned to Ikelite postage paid Ikelite will at its sole discretion repair or replace such products and will return to customer postage paid All other claims of any nature are not covered Except as mentioned above no other warranty expressed or implied applies to this Ikelite product Ikelite Underwater Systems 50 West 33rd Street Indianapolis IN 46208 USA www ikelite com 2015 Ikelite Underwater Systems 9523 64 tray dual handles 2 0215
2. 9523 64 Housing Tray and Dual Handles ik li elite instruction Manual Included in Box Dual Tray Qty 1 Bottom View JC C O Back of Tray Back of Tray Top View 20 TERRE jx Front of Tray Front of Tray Front View T WADE NUSA Hex Head Wrench Right Handle Left Handle 1 4 20 X 3 8 Screw 2 1 4 20 Shoulder Washer 2 lt gt 12 24 X 1 2 Screw 2 Non lkelite Housing Anti rotational Pad 12 24 Shoulder Washer 2 3 8 16 Nylon Washer 3 8 16 Hex Jam Nut Handle Suige Filn 1 4 20 X 5 8 Round Head Small Washer Screw Lockwasher 1 4 20 Nylon Washer Cap Screw Table of Contents INTO GU tiO Naminiai P 2 Attach Quick Release Handles to Dual Tray P 3 Attach Dual Tray to Ikelite Compact Housing featuring 3 8 16 Mounting Bolts P 4 Attach Dual Tray to Ikelite Compact Housing featuring 12 24 or 3 8 16 Mounts 0 ccee P 5 Attach Dual Tray to Ikelite ULTRAcompact Housing featuring 12 24 Mounts 0 000 0 P 6 Attach Dual Tray to Non lkelite Housing featuring a 1 4 20 Mount 00 0 cecceeeeeeteeeeteees P 7 Introduction Thank you for your purchase of Ikelite equipment Please read this instruction manual completely before attempting to operate or dive with this product The 9523 64 Housi
3. front of the camera housing 4 Place a shoulder washer in each 3 8 tray hole with the small end of the washer facing down 5 With your free hand insert and rotate the correct screws clockwise until threaded into the housing mounts Finish tightening the tray to the housing using a flathead screwdriver R mi a z 5 WY J i Attach Dual Tray to Ikelite ULTRAcompact Housing featuring 12 24 Threaded Mounts 1 Place your Ikelite Compact Housing upside down on a flat surface or on your lap Line up the 3 8 tray holes with the housing mounts If the tray is positioned properly the ikelite logo will be facing forward toward the front of the camera housing Place a shoulder washer in each 3 8 tray hole with the small end of the washer facing down With your free hand insert and rotate the 12 24 x 1 2 screws clockwise until threaded into the housing mounts Finish tightening the tray to the housing using a flathead screwdriver Attach Dual Tray to Non Ikelite Housing featuring a 1 4 20 Threaded Mount 1 Remove the protective backing from the Non lkelite Housing Anti rotational Pad Diagram D and place the adhesive side down on the Tray as shown Diagram E 2 Line up the larger non threaded center Tray hole with the housing mount hole If the tray is properly positioned the
4. hesive side facing up 3 Line up the 3 8 Dual Tray holes with the 3 8 Tray Mounting Bolts Diagram C If the tray is positioned properly the ikelite logo will be facing forward toward the front of the camera housing 4 Slide Tray into position over the Spacer and press firmly for a couple seconds This will allow the Spacer to cling to the Tray 5 With your free hand slide the 3 8 16 washers over the Housing Mounting Bolts and tighten tray using the 2 3 8 16 Hex Jam Nuts Finish tightening the tray to the housing using a 9 16 open end or socket wrench Diagram B S g 9 Protective Backing f peel off before use Diagram C Attach Dual Tray to Ikelite Compact Housing featuring 12 24 or 1 4 20 Threaded Mounts 1 Determine the correct thread type for your housing mounts Gently thread a 12 24 screw into one of the housing mounts If there is no resistance and the screw does not seem loose or wobbly in the mount then you have the correct screw A larger diameter 1 4 20 X 3 8 screw will not thread into a smaller 12 24 size mount A CAUTION Using the incorrect screws could damage your housing mounts 2 Once the correct screws have been selected place your Ikelite Compact Housing upside down on a flat surface or on your lap 3 Line up the 3 8 tray holes with the housing mounts If the tray is positioned properly the ikelite logo will be facing forward toward the
5. ng Tray and Dual Handle kit comes complete with hardware to connect both Ikelite and Non lkelite housings The Tray is designed specifically for Ikelite Compact and ULTRAcompact housings Non Ikelite housings can be attached using the Anti rotational Pad and 1 4 20 X 5 8 Screw Attach Quick Release Handles to Dual Tray The Handles are designed to be attached to the Tray one time A Handle can be removed for replacement purposes however constant removal and attachment can wear away the protective coating on the tray and handle which can accelerate corrosion Mount each Handle so that the Push Button extends rearward away from the Tray Front 1 Gently insert Handle Guide Pin into Tray Guide Pin Hole 2 Slide Lock Washer and then Small Washer over small end of Cap Screw 3 Insert Cap Screw through Cap Screw Hole and into handle sc a firmly with Allen gt Push Button 4 Attach remaining Handle to opposite side of Tray Quick Release Handle Diagram A Cap Screw Hole Guide Pin aa Tray Guide Pin i A Hole Tray Front Smal Washer lLockwasher Allen Wrench rotate clockwise to tighten Cap Screw Attach Dual Tray to Ikelite Compact Housing featuring 3 8 16 Mounting Bolts 1 Place your Ikelite Compact Housing upside down on a flat surface or on your lap 2 Peel protective film off Spacer to expose adhesive Diagram B Place Spacer over Housing Mounting Bolts with ad

Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents