Refrigerator User manual Top mount Bottom mount Single door all
Contents
1. Make sure you fully close the freezer and fridge doors If the doors are left open a heavy frost will coat the inside of the freezer If a frost develops remove it and take care to properly close the doors The defrost water tray located at the back or underneath of the cabinet may not be properly positioned or the drain tube may not be properly positioned to direct water into this tray You may need to pull the refrigerator away from the wall to check the tray and tube Turn appliance off at the power point Leave off for three 3 minutes for the memory to clear then turn back on e Check whether something is holding the door open e In normal operation the refrigerator transfers heat from inside to outside of the cabinet It is normal for the side and rear of the refrigerator to feel warm hot while operating This will be more noticeable during start up and hot ambient conditions 26 ICE WATER TROUBLESHOOTING Problem Automatic ice maker The ice maker is not making any ice The ice maker is not making enough ice Ice cubes are too small or too big The ice has a bad odour and taste Possible causes Ice maker is in the OFF position Solution e See Ice maker section in user manual turn switch to ON position Water tap is turned off e Turn on the water tap The freezer is not cold enough e See the Problem section If the temperature in the refrigerator is too warm The water dispenser2. a ee m M M M M M Co O OONO PWN O LED light Electronic controls Spillsafe slide away shelf where fitted Adjustable Spillsafe glass shelf LED fridge light Deli compartments Crisper humidity controls Crisper bins Deodoriser Freezer storage tray ce maker assembly ce bin with scoop inside freezer drawer Freezer drawers on telescopic extension slides Adjustable rollers Dairy compartments Adjustable door bins Egg tray Bottle twist holder where fitted Full width bottle bin Full width bottle bin can bin on smaller models Stabilising foot INSTALLING YOUR NEW APPLIANCE i TIPS amp INFORMATION e For built in models refer to the separate booklet e To join two E Line modular fridges together refer to the booklet with the connection kit Adequate ventilation around your refrigerator The diagram below shows the recommended airspace to allow for ventilation of your refrigerator All models except EBE5167SD If gap Y is not minimum of 100mm then gap X increases from 50 to 90mm For EBE5167SD If gap Y is not minimum of 100mm then gap Z increases from 10 to 45mm When positioned in acorner area spacing of at least 350mm on the hinge side will allow the doors to open enough to enable the removal of bins and shelves Note For those models with telescopic extension slide out bins the clearance required increases from 350mm to 550mm for top mount and bottom moun
3. normal text will appear on the electronic display when your refrigerator is operating in normal mode Normal mode is activated when e The freezer compartment temperature setting is colder than 18 C e The fresh food compartment temperature setting is colder than 3 C e The boost or fast ice function is activated e The door alarm is activated e The freezer temperature alarm is activated e Vacation mode Boost Fastice Vac D Use this function when you go on vacation or leave the house for long periods The refrigerator minimises defrosting to save energy but maintains your temperature settings To put the refrigerator into vacation mode press the modes button until vacation symbol is illuminated The vacation mode will operate until the button is pressed again or the refrigerator door is opened NOTE Opening the freezer drawer won t effect the operation of either Eco or Vacation modes Sabbath Mode Entering Sabbath mode will disable all the refrigerator lighting turn off the ice maker water dispenser and prevent any other electrical activity from occuring as a result of the refrigerator doors being opened To enter Sabbath Mode press and hold the Display lock and lt buttons simultaneously for 3 seconds Four beeps will sound and the display will show sb to indicate Sabbath Mode All alarm functions are disabled except for the High Temperature Alarm for reasons of food safety If there is a hi
4. Deli compartments full width on some models Crisper humidity controls Crisper bins full width on some models Adjustable rollers Freezer door bins Dairy compartments Egg tray Adj Ful Bo ustable door bins width door bin tle twist holder where fitted Full width door bin can bin on smaller models Stabilising foot Deodoriser Fridge and freezer temperature controls manual control models Spillsafe slide away shelf where fitted Bottle caddy Adjustable Spillsafe glass shelf Fridge light Deli compartments full width on some models Crisper humidity controls Crisper bins full width on some models Freezer storage tray Twist amp serve ice Ice bin with scoop inside freezer drawer Freezer drawers on telescopic extension slides Adj Dai Adj ustable rollers ry compartments ustable door bins Egg tray Bo Ful Ful tle twist holder where fitted width bottle bin width bottle bin can bin on smaller models Stabilising foot 6 SINGLE DOOR ALL REFRIGERATOR MODEL AR 11 a E fe a E a m S y oOo AN ODO oa RAON ak ak ee i ee M ee aM NO GO fF OD O Note Product illustrations d
5. O 13 14 Note Product illustrations demonstrate various features but may not be completely in line with current products BUILT IN FREEZER oa A ORN Deodoriser Fridge temperature control Adjustable Spillsafe glass shelves Slideable deli compartment Fridge light Bottle caddy Crisper humidity control Full width crisper bin Dairy compartments Egg tray Half width door bins Bottle restrainers Full width bottle bins Can bin Freezer temperature control Freezer light Air delivery vents Adjustable Spillsafe glass shelves Twist ice amp serve with ice cube trays Freezer baskets with clear fascia Note Product illustrations demonstrate various features but may not be completely in line with current products 8 BOTTOM MOUNT ICE amp WATER MODEL Note EBE5160 shown Product illustrations demonstrate various features but may not be completely in line with current products Boost FastIce Vacation DRINKS CHILL ON Oath WD N N N
6. Act does not apply To the extent permitted by law and subject to your non excludable statutory rights and warranties Electrolux excludes all warranties and liabilities other than as contained in this document including liability for any loss or damage whether direct or indirect arising from your purchase use or non use of the Appliance For Appliances and services provided by Electrolux in Australia the Appliances come with a guarantee by Electrolux that cannot be excluded under the ACL You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the Appliance repaired or replaced if the Appliance fails to be of acceptable quality and the failure does not amount to a maior failure The benefits to you given by this warranty are in addition to your other rights and remedies under a law in relation to the Appliances or services to which the warranty relates At all times during the Warranty Period Electrolux shall at its discretion determine whether repair replacement or refund will apply if an Appliance has a valid warranty claim applicable to it For Appliances and services provided by Electrolux in New Zealand the Appliances come with a guarantee by Electrolux pursuant to the provisions of the Consumer Guarantees Act the Sale of Goods Act and the Fair Trading Act To enquire about claiming under this warranty please fo
7. G Your refrigerator is fitted with a water filter which periodically requires replacement When your filter requires replacement Order filter and Replace filter icons will appear as a reminder to both order and replace the water filter When the replace filter icon appears an alarm will sound pressing any button on the user interface will mute this alarm for one week When the filter has been replaced press and hold the Ice and Water button for three seconds to reset the filter replace timer Other special refrigerator features e Independent control of the compressor and fan to provide the best performance e Extra cooling depending on the number of times the door is opened e Automatically adjusts defrost time when the door is not frequently opened NOTE Display malfunctions may be due to brief power supply interruptions If this occurs turn the refrigerator off at the power point and wait 5 minutes The refrigerator pressure will need time to equalise before you turn the refrigerator on again 19 MANUAL ROTARY CONTROLS MANUAL MODELS Controlling the temperature Set the temperature by using the main temperature controls at the rear of the refrigerator compartment When you first start your refrigerator set both refrigerator and freezer controls to MID i TIPS amp INFORMATION A good indication of optimal freezer temperature is ice cream that is frozen but still soft enough for easy scooping For
8. installed position QO S OS EO VIO Never unplug the appliance by pulling on the power cord Always grip the plug firmly and pull straight out of the receptacle to prevent damaging the power cord Don t plug your refrigerator into a timer fitted to the power point Do not put the refrigerator in frosty or unprotected areas for example in a garage or on a veranda Do not put the refrigerator in direct sunlight near stoves fires or heaters Do not put the refrigerator on an uneven surface Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance COO l Do not use electrical appliances inside the food storage compartments of the appliance unless they are of the type recommended by the manufacturer Never store fizzy drinks in the freezer compartment Never try to repair the refrigerator yourself only use a qualified or authorised service person for repairs Never use electric heaters or dryers to defrost the freezer because you can receive an electric shock l l Do not damage the refrigerant circuit Do not use with water that is microbiologically unsafe or with water of unknown quality without adequate disinfection Never connect the appliance to a hot water supply Never install the water filter in an area of the wall where there may be electrical wires and or water supply pipes Never install the wa
9. may not be dispensing water e lfitisn t the ice amp water filter cartridge may be clogged or restricted by foreign material and will need to be replaced Filter may be blocked The ice maker is producing less ice than you expect e Check and or change filter e The ice maker should produce approximately 0 5 1 kilogram of ice every 24 hours Household water tap is not open e Open the household water tap The water dispenser is dispensing slower than normal e Replace the water filter cartridge The freezer is not cold enough Restricted water flow to the ice maker e See section Controlling temperatures e Replace the filter cartridge as the water filter cartridge may be clogged Water pressure may be too low e Check water supply hose for kinks Water pressure may be too high The ice has picked up odour or flavour from strongly flavoured food stored in the refrigerator or freezer e Check water pressure meets minimum and maximum requirement see install instructions e Cover foods tightly Discard stale ice The ice maker will produce a fresh supply The water running into the ice maker has poor taste or colour e Add or replace water filter to water supply Consult a water purifying company Ice not used frequently enough e Discard stale ice monthly 2 Electrolux Warranty FOR SALES IN AUSTRALIA AND NEW ZEALAND APPLIANCE REFRIGERATION This document sets out the terms
10. remove or adjust a bin lift it over the support lugs on the inner door panel To replace push the bin down over the support lugs to lock it in place Dairy compartment Use the dairy compartment to store foods like butter margarine and cheeses The compartment is slightly warmer than the rest of the refrigerator compartment while the lid provides protection against odours Chiller bin where fitted Use the chiller bin to store foods like small goods fresh or cooked meat and cheese or as an additional crisper The bin will prevent strong food odours from creeping into the rest of the refrigerator To remove the chiller bin pull it forward then lift it up and pull it further forward Bottle caddy The bottle caddy is made of stainless steel It is used to store various types of bottles like wine or beer Bottles should be stored with the bottom end towards the back of the refrigerator Freezer drawers Freezer drawers are fitted to bottom mount models and single door all freezer models The drawers are mounted on telescopic extension slides to enable full access to the content in the drawer Clear plastic fronts provide easy visibility of foods e To remove the drawer for cleaning 1 Empty food from the drawer 2 Remove the drawer by pulling it forward and lifting the front to unhook it from the slides Once you have removed the drawer ensure the slides are pushed back so they are ful
11. temperature We recommend that when you start your refrigerator for the first time the temperature for the refrigerator is set to 3 C and the freezer to 18 C If you want to change the temperature follow the instructions below Make only small adjustments and wait 24 hours to see if it s correct Checking the softness of ice cream is a good indication if your freezer is the right temperature while checking the temperature of water kept in the refrigerator is a good way of checking the temperature of the food compartment NOTE When you set a temperature you set an average temperature for the whole refrigerator cabinet Temperatures inside each compartment may vary depending on how much food you store and where you place it High or low room temperature may also affect the actual temperature inside the refrigerator Changing the freezer temperature Press the freezer button to make the freezer colder in 1 C steps Once the maximum of 23 C is reached the display will return to 14 C with the next press of the button The bar graph gets smaller with colder freezer settings Changing the refrigerator temperature o Je Press the fridge button to make the mi refrigerator colder in 1 C steps Once 0 C is reached the display will return to 7 C with the next button press The bar graph gets smaller with colder refrigerator settings 15 ELECTRONIC DISPLAY CONTROLS ELECTRONIC MODELS Fast freeze function Use the
12. the fridge compartment we recommend using drinking water and simply adjusting the fridge controls until the water is at your ideal temperature To change settings When you change temperature settings make small adjustments and wait 24 hours before assessing whether you need to make any further changes i TIPS amp INFORMATION Coldest freezer setting is not recommended in normal and very hot climates as this will limit the cooling to the refrigerator section e In very cold climates where temperatures are below 10 C the freezer may need to be set colder Adjusting the freezer temperature top mount freezer TM model Select the freezer control top knob 2 Rotate the knob clockwise to set colder 3 Rotate the knob anti clockwise to set less cold wes less colder M treezer O Adjusting the refrigerator temperature top mount freezer TM model Select the refrigerator control bottom knob Rotate the knob clockwise to set colder Rotate the knob anti clockwise to set less cold on gt MID refrigerator less colder cold 20 MANUAL ROTARY CONTROLS MANUAL MODELS e Adjusting the refrigerator temperature bottom mount freezer BM model 1 Select the refrigerator control top knob 2 Rotate the knob clockwise to set colder 3 Rotate the knob anti clockwise to set less cold less colder cold S im refrigerator MID e Adjusting the freezer temperature bottom mount
13. transported by Electrolux or an Electrolux authorised representative the Appliance is transported at the owner s cost and risk while in transit to and from Electrolux or its ASC 6 Proof of purchase is required before you can make a claim under this warranty 10 Ti 12 13 14 27 You may not make a claim under this warranty unless the defect claimed is due to faulty or defective parts or workmanship Electrolux is not liable in the following situations which are not exhaustive a the Appliance is damaged by i accident ii misuse or abuse including failure to properly maintain or service ili normal wear and tear iv power surges electrical storm damage or incorrect power supply v incomplete or improper installation vi incorrect improper or inappropriate operation vii insect or vermin infestation viii failure to comply with any additional instructions supplied with the Appliance the Appliance is modified without authority from Electrolux in writing the Appliance s serial number or warranty seal has been removed or defaced d the Appliance was serviced or repaired by anyone other than Electrolux an authorised repairer or ASC This warranty the contract to which it relates and the relationship between you and Electrolux are governed by the law applicable where the Appliance was purchased Where the Appliance was purchased in New Zealand for commercial purposes the Consumer Guarantee
14. unsure If the power cord is damaged it must be replaced by the manufacturer it s service agent or similarly qualified persons in order to avoid a hazard Check that the power cord can reach the power point Don t plug your refrigerator into an extension cord or double adaptor Unplug the appliance before cleaning or moving A CAUTION Automatic aerosol systems such as insect control should not be located adjacent to the product as the spray may cause long term damage to the external plastics of the appliance Note You must read these warnings carefully before installing or using the refrigerator If you need assistance contact your Customer Care Department The manufacturer will not accept liability should these instructions or any other safety instructions incorporated in this book be ignored For Ice amp Water models only Check for water leaks at all water connection points in the first two or three hours after installation Re check after 24 hours to ensure connection is watertight If the connection is leaking contact a licensed plumber Choose a location that is not too cold the ambient temperature should be above 10 C Put the refrigerator in a dry place avoiding areas of high moisture or humidity Keep ventilation openings in the appliance enclosure or in the built in structure clear of obstruction The plug to the appliance must be accessible when the unit is in the
15. CHILL ICE amp WATER ate CE amp WATE ON OFF E Hold 3sec Replace Filter Controlling the temperature We recommend that when you start your refrigerator for the first time the temperature for the refrigerator is set to 3 C and the freezer to 18 C If you want to change the temperature follow the instructions below Make only small adjustments and wait 24 hours to see if it s correct Checking the softness of ice cream is a good indication if your freezer is the right temperature while feeling the coldness of water kept in the refrigerator is a good way of checking the temperature of the food compartment NOTE When you set a temperature you set an average temperature for the whole refrigerator cabinet Temperatures inside each compartment may vary depending on how much food you store and where you place it High or low room temperature may also affect the actual temperature inside the refrigerator If no button has been pressed for some time there may be a delay of up to 2 seconds before the display responds this is normal and is a part of the display design to reduce the chance of accidental changes Changing the freezer temperature SELECT Press the Select button until the freezer compartment is illuminated on the refrigerator icon Use the arrows to the left and right of the display to select a higher or lower temperature in 1c steps Once the maximum of 23 c is reached the display will return to 14 c
16. No A00394701 2014 Electrolux Home Products Pty Ltd ABN 51 004 762 341 EMAN_EFRI_Sept14
17. al for noise to seem louder when the refrigerator starts operating or during quieter periods such as night time e The interior may need cleaning e Some foods produce odours e Some containers and wrapping can cause odours e Ask yourself if the odour started about the same time you started storing something unusual Your new refrigerator has a large fridge and freezer section to keep cool So it is normal to frequently hear the sound of the motor However to keep operation to a minimum check the following e Are doors kept open too long or too often e Are controls set too cold See Controlling the temperature on page 12 e Have large amounts of warm food just recently been stored Summer festive seasons and holidays usually mean a lot more work for your refrigerator e f the day is hot or the room is very warm the refrigerator will need to run more than normal e The refrigerator will run more that normal just after you install it or when it has been turned off for a long time e Check that the appliance has enough clearance at the sides back and top Refer to the installation instructions on page 6 e Refer to Controlling the temperature on page 12 e You may have kept the door open too long or too frequently e Food containers or packaging may be holding a door open e Refer to Controlling the temperature on page 12 e Increase the temperature to avoid high energy consumption
18. all freezer drawers and shelves are pushed back completely to prevent them from keeping the door open ICE amp WATER INSTALLATION A WARNING Connect to potable water supply only The external water filter kit An external water filter and connection kit has been supplied for use with your Ice amp Water refrigerator The external filter design allows more space within the refrigerator and provides double the life of previous filters reducing the cost of replacement The filter is designed to significantly reduce chlorine taste odour heavy metals turbidity cloudiness and scale build up The included plastic water tube allows quick connection to the filter and is designed for high durability and kink resistance This filter is designed only to be used with a potable water supply It should not be used on water that is micro biologically unsafe or with water of unknown quality The filter should be replaced every 12 months The service life of the filter may be reduced in water supplies that contain an excess of particles or other impurities Reduced flow rate is an indication that a new filter is required Failure to replace the filter when required can affect the function of the ice maker Service calls caused by a failure to replace the filter are not covered by warranty Contents of installation kit FLOW DIRECTION DATE FITTED_ __ __ 1 x water filter with push fit connections o INAV NNA S 2 x mount
19. and conditions of the product warranties for Electrolux Appliances It is an important document Please keep it with your proof of purchase documents in a safe place for future reference should you require service for your Appliance 1 In this warranty a acceptable quality as referred to in clause 10 of this warranty has the same meaning referred to in the ACL b ACL means Schedule 2 to the Competition and Consumer Act 2010 Appliance means any Electrolux product purchased by you and accompanied by this document ASC means Electrolux authorised service centres Electrolux means Electrolux Home Products Pty Ltd of 163 O Riordan Street Mascot NSW 2020 ABN 51 004 762 341 in respect of Appliances purchased in Australia and Electrolux NZ Limited collectively Electrolux of 3 5 Niall Burgess Road Mount Wellington in respect of Appliances purchased in New Zealand f major failure as referred to in clause 10 of this warranty has the same meaning referred to in the ACL and includes a situation when an Appliance cannot be repaired or it is uneconomic for Electrolux at its discretion to repair an Appliance during the Warranty Period g Warranty Period means the Appliance is warranted against manufacturing defects in Australia and New Zealand for 24 months and for the Appliance s compressor condenser evaporator and drier an additional 36 months parts only warranty applies followin
20. arks such as finger prints and water spots To keep your stainless steel appliance looking at its best you should clean it regularly You should only clean the stainless steel doors with luke warm soapy water and a soft cloth rinsing with clean water and then wipe the surface with clean water and a soft clean cloth to remove soap residue It is important to wipe in the direction of the grain of the stainless steel to avoid undue marking of the surface e Doors surface hardened acrylic You should only clean the acrylic doors with lukewarm soapy water and a soft cloth rinsing with clean water and the wipe the surface with clean water and a soft clean cloth to remove soap residue A CAUTION Do not use stainless steel cleaners abrasive pads or other cleaners as they are likely to scratch the surface Damage to this product after delivery is not covered by your warranty e interior You should clean the appliance interior regularly It will be easiest to clean when the food supply is low Wash the interior with a soft cloth and use an unscented mild soap with lukewarm water Thoroughly dry all surfaces and removable parts Avoid getting water on appliance controls If you have taken out any removable parts replace them and switch the power on before re stocking the appliance with food Naturally you should keep the interior of your appliance hygienic by promptly and thoroughly wiping up any food spills Don t use a steam cleane
21. care electrolux com au web www electrolux com au Electrolux Home Products New Zealand telephone 0800 436 245 fax 0800 225 088 email customercare electrolux co nz web www electrolux co nz The Thoughtful Design Innovator Do you remember the last time you opened a gift that made you say Oh How did you know That s exactly what wanted That s the kind of feeling that the designers at Electrolux seek to evoke in everyone who chooses or uses one of our products We devote time knowledge and a great deal of thought to anticipating and creating the kind of appliances that our customers really need and want This kind of thoughtful care means innovating with insight Not design for design s sake but design for the user s sake For us thoughtful design means making appliances easier to use and tasks more enjoyable to perform freeing our customers to experience that ultimate 21st century luxury ease of mind Our aim is to make this ease of mind more available to more people in more parts of their everyday lives all over the world So when we say we re thinking of you you Know we mean just that The Thinking of you promise from Electrolux goes beyond meeting the needs of today s consumers It also means we re committed to making appliances safe for the environment now and for future generations Electrolux Thinking of you Share more of our thinking at www electrolux com au or www electrolux co nz P
22. d rear side of the refrigerator solution e Check that the power cord is plugged into the power outlet properly and that the outlet is switched ON e Try running another appliance from the power outlet If no power is coming from the outlet you may have blown a fuse or tripped a circuit of your household power supply e Try adjusting the temperature control to a slightly colder position e It is normal for the freezer fan NOT to operate during the automatic defrost cycle or for a short time after the appliance is switched on Modern refrigerators freezers with increased storage capacity use high speed compressors These can provide a seemingly high level of sound which is quite normal Normal operational sounds include e Occasional gurgling similar to water boiling e Air flow noise air circulates because of a small fan e A popping noise heard during automatic defrost e A clicking noise heard just before the compressor starts this is just the automatic switching action of the temperature control turning the compressor on or off Other strange sounds may mean that you need to check and take action For example noises may mean that e The cabinet is not level e The floor is uneven or weak e Bottles are badly placed and rattling e There are vibrations from an object on top of or behind or beside the refrigerator e The back of the refrigerator cabinet is touching the wall Remember it is quite norm
23. e pee Use this button when you go on Z holiday or leave the house for long F periods The refrigerator minimises defrosting to save energy but maintains your temperature settings To put the refrigerator into holiday mode press the eco holiday mode button until the aeroplane icon appears The holiday mode will operate until the button is pressed again or the refrigerator door is opened NOTE Opening the freezer door won t effect the operation of either Eco or Holiday modes Eco and Holiday Modes minimise defrosting to save energy while maintaining your temperature settings Other special refrigerator features electronic models only e Independent control of the compressor and fan to provide the best performance e Extra cooling depending on the number of times the door is opened e Automatic defrost when the door is not frequently opened NOTE Display malfunctions may be due to brief power supply interruptions If this occurs turn the refrigerator off at the power point and wait 5 minutes The refrigerator pressure will need time to equalise before you turn the refrigerator on again The electronic display panel consists of an LCD display with white backlighting When the power is first turned on the display with backlighting will activate If no buttons have been pressed and the fridge door is closed the backlighting will turn off after 30 seconds SELECT Boost FastIce Vacation DISPLAY MODES DRINKS cK
24. emonstrate various features but may not be completely in line with current products SINGLE DOOR ALL FREEZER MODEL AF Note Product illustrations demonstrate various features but may not be completely in line with current products oO ON ODO OA PF OD 10 Deodoriser Fridge temperature control Adjustable Spillsafe glass shelves Spillsafe slide away shelf where fitted Fridge light Deli compartments Bottle caddy Crisper humidity control Full width crisper bin Adjustable rollers Dairy compartments Egg tray Adjustable door bins Bottle twist holder Full width bottle bins Can bin Stabilising foot Freezer temperature control Freezer light Air delivery vents Adjustable Spillsafe glass shelves Twist amp serve ice Freezer storage tray Ice bin with scoop inside freezer drawer Freezer drawers on telescopic extension slides Stabilising foot Adjustable rollers BUILT IN REFRIGERATOR oMOAN OA PF WOOD A no
25. erator isn t tilted back you can adjust the two front rollers by turning the large plastic roller nut see diagram below One turn of the nut increases the height of the refrigerator by 10mm If you have difficulty turning the roller nut have someone tilt the refrigerator back so you have better access Alternatively you can access the rollers from the side using a flat screwdriver See diagram below Large plastic roller nut Stability foot wound up 4 Check the alignment of the refrigerator to the surrounding cupboards to see if it is level You can adjust the level with the rollers as detailed in step 3 Aligned to cupboards gt lt e even gap Top of refrigerator is level ie horizontal lt Adjust front rollers for uneveness of floor oe wind this roller i down or up 5 Ifyou find your refrigerator rocks from corner to corner it means your floor is uneven Find a piece of plastic or hardboard etc and pack it firmly under the roller 6 Oncertain floor surfaces the refrigerator may roll forward during operation Where provided a Roller Stop can be placed under the front rollers If roller stop is required please contact Customer Service details on back page and quote part no 1448845 lt Roller Stop 10 INSTALLING YOUR NEW APPLIANCE 7 You may now need to fine tune the installation by repeating Steps 3 4 and 5 8 When you have the appliance in
26. es To set simply press the drinks chill button and an initial time of 20 minutes appears To adjust the timer use the lt arrow buttons gt to a maximum of 30 minutes or a minimum of 5 minutes in 5 minute steps Once set a time will count down one minute at a time You can change the time or turn the timer off even after the countdown has started A buzzer will tell you when the time is finished and the icon will flash until the alarm reset button is pressed If your drink is not cold enough reset the drinks chill function remembering the drink is already partially chilled Suggested chilling times e 10 minutes for cans of drink e 20 minutes for bottles of wine e 30 minutes for bottles of soft drink Energy efficiency Your refrigerator has been designed to be energy efficient and can operate in three modes Normal Eco and Vacation e Eco mode gt Boost Fast Ice Vacation Eco mode is the default mode of your refrigerator The leaf icon will automatically appear on the electronic display when your refrigerator is operating in Eco mode Eco mode is activated when e The freezer temperature setting is 17 or warmer e The fresh food compartment temperature setting is 3 or warmer e The boost or fast ice is not activated e Door or freezer temperature alarms are not activated e Normal mode Normal mode is used when you require extra cooling or when the refrigerator door is opened more than usual The
27. far To remove the basket or shelf pull it out until it hits the stop then lift the front to unhook the stop while continuing to pull forward USING YOUR APPLIANCE Spillsafe glass shelves Spillsafe glass shelves keep spills on the shelf A shelf retaining system minimises accidental movement of shelves and they can be adjusted to various heights Spillsafe glass shelves are not to be used as slide out shelves To remove the shelves gently pull them forward until the shelf comes clear of the shelf guides To return the shelf make sure there is nothing behind that may obstruct movement Gently push the shelf into the cabinet and back into position Slide away glass shelf where fitted This shelf can be used either as a full depth shelf or when tall items need to be stored at the front of the appliance it can be collapsed to half its original depth To collapse the shelf 1 Pull the front half of the shelf forward 2 Then from the underside lift the front half of the shelf by raising the rear edge over the recessed hook detail 3 Pull the shelf forward and allow the rear to drop into the side channels 4 Push the front shelf backwards 3 4 until it reaches the rear stops e Repositioning The shelf can be repositioned within the appliance unit by pulling the whole assembly out until the side panels are free to pivot down then pivoting the rear of the shelf until the shelf is free from t
28. fast freeze function when you add h a large amount of food to the freezer compartment This freezes the food quickly but does not affect the temperature in the refrigerator compartment To use this function press the fast freeze button once An animated icon will light up The fast freeze function will now operate for 90 minutes If you want to turn the fast freeze function off before 90 minutes have passed simply press the fast freeze button again The icon will disappear and the freezer will return to normal operation Freezer temperature alarm If the alarm sounds for no apparent reason check whether anything is keeping the yam oor open If the freezer becomes too warm due to the freezer door being left open or warm food being placed too close to the temperature sensor a buzzer will sound The icon adjacent to the alarm reset button the freezer set temperature and bar graph will all flash until the alarm reset button is pressed Once pressed the alarm disable icon adjacent to the alarm button will illuminate for 50 minutes or until the temperature drops to an acceptable level Make sure nothing is holding the freezer door open and move any warm food away from the temperature sensor If the freezer is still too warm after 50 minutes the alarm will sound again indicating that something may be wrong with the refrigerator NOTE The freezer temperature alarm can be reset for 12 hours by pressing the alarm reset button con
29. freezer BM model Select the freezer control bottom knob Rotate the knob clockwise to set colder Rotate the knob anti clockwise to set less cold QO freezer on less colder cold MID e Adjusting the all refrigerator temperature single door all refrigerator AR built in refrigerator models Rotate the knob clockwise to set colder Rotate the knob anti clockwise to set less cold M less colder cold MID e Adjusting the all freezer temperature single door all freezer AF and built in freezer model Rotate the knob clockwise to set colder Rotate the knob anti clockwise to set less cold D o Colder Less Cold USING YOUR APPLIANCE Crisper bin Use the crisper bin to store vegetables fruit or small goods Change the humidity by sliding or rotating the humidity control a Humidity control e Storing vegetables Store vegetables in the crisper bin and remember to set the humidity control to more humid closed e Storing fruit amp small goods Store fruit and small goods in the crisper bin and remember to set the humidity control to less humid open e Removal standard Crisper Bins 1 Empty food from the drawer 2 Remove the crisper bin s by pulling forward then up and forward again 3 Remove the crisper shelf by lifting the catches on the underside of the shelf and pulling the shelf forward Catch e Removal on telescopic extension slides Remo
30. from the temperature sensor If the freezer is still too warm after 50 minutes the alarm will sound again indicating that something may be wrong with the refrigerator NOTE The freezer temperature alarm can be reset for 12 hours by holding the alarm reset button continuously for 10 seconds Door alarm If the fridge or freezer door is left open for more than two minutes the alarm will buzz and an arrow pointing to an open door will flash along with the temperature setting and bar graph If you want to leave the door open while you load the refrigerator you can turn the alarm off for 8 minutes by pressing any button If the fridge door is left open for more than 30 minutes the light will automatically turn off to save energy To turn the light back on simply close and reopen the door again 18 ELECTRONIC DISPLAY CONTROLS ICE amp WATER MODELS Display Lock Boost Fast lce Vacation MODES DRINKS CHILL Order Filter Press and hold the Display Lock button for 3 seconds to activate the display lock This will disable the display to prevent accidental changes to settings To turn the display lock off hold the Display Lock button for 3 seconds Drinks chill timer Boost Fast Ice Vacation DISPLAY MODES k gt LOCK C CHILL Hold 3seo Order Filter The drinks chill timer is used to quickly chill a bottle Place the bottle in the freezer and the timer can be set for a minimum of 5 minutes to a maximum of 30 minut
31. g supply stores or good hardware stores Water filter Locate the water filter as close as possible to the water supply tap in a vertical position where possible The filter will need to be replaced every 12 months to prevent excess filtered micro organism build up and thus ensure continuous purified water and ice supply for you and your family Replacement water filters are available from Electrolux Home Products Spare Parts Centres and can be posted to you for your convenience refer to back page for contact details A CAUTION If the appliance is not connected to a water supply ensure that the ice maker is switched off refer to STEP 1 overleaf If you don t do this a loud buzzing noise will be heard intermittently The new hose sets supplied with the appliance must be used and old hose sets should not be reused Do not use with water that is microbiologically unsafe or with water of unknown quality without adequate disinfection Never connect the appliance to a hot water supply Never install the water filer in an area of the wall where there may be electrical wires and or water supply pipes 12 ICE amp WATER INSTALLATION Never install the water filter in an area of direct sunlight Check for water leaks at all water connection points in the first 2 to 3 hours after installation and correct it in case of any water leak Recheck after 24 hours if leak still occurs it is recommended to contact a licensed plumber fo
32. g the date of original purchase of the Appliance h you means the purchaser of the Appliance not having purchased the Appliance for re sale and your has a corresponding meaning 2 This warranty only applies to Appliances purchased and used in Australia or New Zealand and used in normal domestic applications and is in addition to and does not exclude restrict or modify in any way any non excludable statutory warranties in Australia or New Zealand 8 During the Warranty Period Electrolux or its ASC will at no extra charge if your Appliance is readily accessible for service without special equipment and subject to these terms and conditions repair or replace any parts which it considers to be defective Electrolux or its ASC may use remanufactured parts to repair your Appliance You agree that any replaced Appliances or parts become the property of Electrolux This warranty does not apply to light globes batteries filters or similar perishable parts 4 Parts and Appliances not supplied by Electrolux are not covered by this warranty 5 To the extent permitted by law you will bear the cost of transportation travel and delivery of the Appliance to and from Electrolux or its ASC If you reside outside of the service area you will bear the cost of a travel of an authorised representative b transportation and delivery of the Appliance to and from Electrolux or its ASC In all instances unless the Appliance is
33. gh temperature issue during this period the alarm will sound intermittently for 10 minutes then turn off on its own To exit Sabbath Mode press and hold the Display Lock and lt buttons simultaneously for 3 seconds Four beeps will sound and the refrigerator will resume normal operation Boost Fastlce Vacation gt DRINKS LOCK CHILL Hold 3sec Order Filter ELECTRONIC DISPLAY CONTROLS ICE amp WATER MODELS Fast ice Boost Fast ce Vacation DISPLAY LACK CHILI The fast ice mode allows for increased production of ice which is useful for entertaining To use this function press the Modes button until Fast Ice is illuminated The fast ice function will now operate for 12 hours If you want to turn the fast ice off before 12 hours have passed simply press the Modes button again until the Fast ice icon disappears and the refrigerator will return to normal operation Disabling and enabling ice maker and water dispenser Replace Filter Icemaker Off Water Off J o DOOR A ICE amp WATER A ON OFF Hold 3sec Replace Filter To disable enable the automatic icemaker and or the water dispenser press the Ice amp Water on off button to cycle through to the next combination When the icemaker or water dispenser is disabled the icon Icemaker Off or Water Off will be illuminated Filter replacement DISPLAY MODES DRINKS LOCK CHILL Hold 3sec Order Filter Replace Filter Icemaker Off Water Off
34. he liner runners The shelf can then be positioned in any of the runners This is a very useful feature if your appliance door happens to have limited access Deodoriser where fitted Your appliance is fitted with a deodoriser to assist with the removal of food odours inside your appliance Odours are removed by absorption through the filter by the normal operation of the appliance Keeping food covered and wrapping food with plastic wrap will also help to reduce the odours inside your appliance Bottle twist holder operation where fitted The bottle twist holder is used to prevent bottles from falling over The bottle twist holder consists of two parts a Sliding front and a rotating retainer ring The bottle twist holder can be used in two positions e Horizontal When the bottle twist holder ring is horizontal any item that fits within the ring can simply be placed inside it e Vertical When the bottle twist holder ring is vertical it is possible to simply slide the bottle twist holder along the bottle retainer bar until it is pushed up against a bottle Note The bottle should be constrained on the other side by either the end of the bin or other adjacent bottles USING YOUR APPLIANCE Twist ice amp serve where fitted Top mount bottom mount and single door all vertical freezer models have a twist ice amp serve ice cube tray assembly To use remove the tray fill with water and place back in
35. i ae o yon Electrolux Top mount Refrigerator User manual Bottom mount Single door all refrigerator Single door all freezer Built in refrigerator Built in freezer 2 WE RE THINKING OF YOU Thank you for purchasing an Electrolux appliance You ve chosen a product that brings with it decades of professional experience and innovation Ingenious and stylish it has been designed with you in mind So whenever you use it you can be safe in the knowledge that you ll get great results every time Welcome to Electrolux LEGEND The symbols you will see in this booklet have these meanings A WARNING This symbol indicates information concerning your personal safety A CAUTION This symbol indicates information on how to avoid damaging the refrigerator i IMPORTANT This symbol indicates tips and information about use of the refrigerator ENVIRONMENT This symbol indicates tips and information about economical and ecological use of the refrigerator CONDITIONS OF USE This appliance is designed and intended to be used in normal domestic applications only RECORD MODEL AND SERIAL NUMBER HERE Model Serial No CONTENTS OANN OO A FW 20 Important safety instructions General warnings Top mount freezer model features Bottom mount freezer model features Single door all refrigerator model features Single door all freezer model features Built in refrigerator model features Bui
36. ilter OUTLET Step 11 Connect other end of remaining tube length to inlet on bottom right hand side of refrigerator inlet location 14 ICE amp WATER INSTALLATION Step 15 Tips and Useful Information Using a large container run the water dispenser to clear air from lines This may take a few minutes Purge and Ensure that taps are turned off when replacing and fitting filters Remember to turn the taps back on when filter dispense a minimum of 2 litres of water Initial water may Sele IB aee be black in colour This is residual carbon dust from the filter and is non toxic If the water is slow to shut off or Always fit filter as per manufacturer s instructions paying the dispenser is dripping air may still be in the lines Soda ven tenia WEET Ueno ent Either purge more water through the system to remove Ifyou need to replace water tube only use approved this air or allow some time for the air to be removed over water quality piping that meets the pressure requirements subsequent dispensing Do not allow the water tubing to become kinked or trapped under the refrigerator when moving the refrigerator back into position Make sure your refrigerator is level to avoid uneven ice cubes After installation run the water dispenser for a few minutes to remove carbon dust and to ensure that all air bubbles have been purged from the tubing Dripping may occur if air bubbles
37. ing brackets and screws P CN e A r 4 1 metres of water tubing 1 x 1 2 tap fitting 2 x circlips 11 Please read before beginning installation The water connection to your ice and water product can be self installed It is recommended that you seek advice from a licensed plumber if necessary before commencing the installation A CAUTION Your warranty may be voided by an incorrect installation Water supply and plumbing A drinkable water supply to suit a 1 2 tap fitting is required adjacent to the refrigerator It is recommended that a licensed plumber install a new water supply outlet nearer to the appliance should the tubing supplied not be long enough It is not recommended that the tubing be extended as this could adversely affect the flow of water to the ice maker or water dispenser The water dispenser and automatic ice maker require a drinkable water supply with a pressure range of between 206kPa and 689kPa 30PSI and 100PS If the water supply is above 100psi a pressure limiting valve should be installed It is recommended that a Noise Reduction Valve also be fitted in the water supply line This will reduce water hammer and its effects from quick action house hold taps and fast acting valves on appliances The refrigerator water valve is pre fitted with a push fit connector for inserting the water tube Where the tap connection is other than 1 2 adapters can be purchased from plumbin
38. it with a bulb that is the same as the original If when you remove the light bulb the small rubber O ring comes out with the bulb fit the O ring over the new bulb and screw bulb into the socket see diagram below Ensure the O ring is in place before replacing the bulb Light bulb O ring Light socket Insert into the slot at A WARNING ey S Never insert your finger into the light bulb socket to check for the presence of the O ring Then engage into the front of the shelf Ss a 5 Replace the light cover by hooking the light cover lugs N into the bottom of the housing and pressing the upper part of the cover until it clips in 6 Replace shelves 7 Wait 5 minutes to ensure pressures in the refrigeration system are equalized Then reconnect and turn the refrigerator on at the power point LE 5 Fit the carriage by sliding it into the runners until the front of the carriage engages with the shelf 6 Refit the ice tray and ice bin 24 CARE AND MAINTENANCE e Freezer light where fitted Top freezer model electronic models only Single door all freezer and built in freezer model 1 Switch off the power at the power point and remove the refrigerator s power cord from the power point 2 Carefully unclip the light cover You do this by pulling the light cover tab at the rear towards the front of the cabinet 8 Unscrew the light bulb and replace i
39. its final position it needs to be stabilised Wind the stability foot down to the floor until it just makes contact with the floor Lift the front of the appliance to take the weight off the stability foot then turn it turn further to ensure firm contact with the floor Whenever you need to move the appliance be sure to wind the foot back up so that the appliance can roll freely and be sure to reset it when reinstalling side view Stabilising foot wound down _____ front view Y4 turn 9 Clean your refrigerator thoroughly following the instructions on page 15 and wipe off any dust that has accumulated during shipping 10 Plug your refrigerator straight into its own power point and never use a double adapter If you need to roll the refrigerator to get to the plug remember to raise the stability foot first 11 Before you put any food in your refrigerator it s recommended you leave it on for 2 or 3 hours to check it is running properly Congratulations You have successfully installed your new refrigerator i TIPS amp INFORMATION For built in model the plug must be accessible after installation INITIAL START UP Refrigerators work by transferring heat from the food inside to the outside air This operation makes the back and sides of the refrigerator particularly at start up feel warm which is normal A cooling coil is located behind the rear wall of the freezer section in top mou
40. l operation and unplug the appliance at the power point Call authorised service for necessary action and advice e Leaking refrigerant may ignite vent area if leak occurs e The room for installing appliance must be at least 1m3 per 8g of refrigerant The amount and type of refrigerant in the appliance can be found on the rating plate inside the appliance e itis hazardous for anyone other than an Authorised Service Person to service this appliance In Queensland Australia the Authorized Service Person MUST hold a Gas Work Authorisation for hydrocarbon refrigerants to carry out servicing or repairs which involve the removal of covers Switching off your appliance If the appliance needs to be switched off for an extended period the following steps should be taken to reduce the symptoms of mould 1 Remove all food 2 Remove the power plug from the power point 8 Clean and dry the interior thoroughly 4 Ensure that all the doors are wedged open slightly for air circulation GENERAL WARNINGS Read the following carefully to avoid damage or injury O This symbol indicates never to do this This symbol indicates always do this It is important to use your refrigerator safely Check these safety points before using your refrigerator The appliance must be plugged into its own dedicated 220 240V 50Hz AC electrical outlet Ensure that the electrical outlet is properly earthed Consult a qualified electrician if you are
41. llow these steps a carefully check the operating instructions user manual and the terms of this warranty b have the model and serial number of the Appliance available c have the proof of purchase e g an invoice available d telephone the numbers shown below You accept that if you make a warranty claim Electrolux and its ASC may exchange information in relation to you to enable Electrolux to meet its obligations under this warranty g Important Notice Before calling for service please ensure that the steps listed in clause 13 above have been followed FOR SERVICE SERVICE AUSTRALIA FOR SPARE PARTS or to find the address of your nearest A Electron or to find the address of your nearest state service centre in Australia state spare parts centre in Australia PLEASE CALL 13 13 49 ELECTROLUX HOME PRODUCTS PLEASE CALL 13 13 50 For the cost of a local call Australia only www electrolux com au For the cost of a local call Australia only FOR SERVICE SERVICE NEW ZEALAND FOR SPARE PARTS or to find the address of your nearest 2 El 1 or to find the address of your nearest authorised service centre in New Zealand Coor state spare parts centre in New Zealand FREE CALL 0800 10 66 10 ELECTROLUX NZ Limited FREE CALL 0800 10 66 20 New Zealand only www electrolux co nz New Zealand only GFR_Warr_Aug13 Electrolux Home Products Australia telephone 1300 363 640 fax 1800 350 067 email customer
42. lt in freezer model features Ice amp water models Installing your new appliance Initial start up Ice amp water installation Electronic display controls electronic models only Controlling the temperature Freezer temperature alarm Door alarm Child lock Drinks chill timer Energy efficiency Electronic display controls ice amp water models only Controlling the temperature Freezer temperature alarm Door alarm Child lock Drinks chill timer Energy efficiency Fast ice Filter replacement Manual rotary controls manual models Using your appliance Crisper bin Door storage bins Dairy compartment Chiller bin Bottle caddy Freezer drawers Freezer baskets Spillsafe glass shelves Slide away glass shelf Decdoriser Bottle twist holder Twist ice amp serve Ice station Care and maintenance Changing the lightbulb Cleaning the appliance Troubleshooting Ice amp water troubleshooting Warranty IMPORTANT SAFETY INSTRUCTIONS Before you use the refrigerator we recommend that you read through the relevant sections of this manual which provides the description of your appliance and its functions To avoid the risks that are always present when you use an appliance it is important that the appliance is installed correctly and that you read the safety instructions carefully to a
43. ly closed 21 e To remove the drawer for cleaning 1 Empty food from the drawer 2 Remove the drawer by pulling it forward and lifting the front to unhook it from the slides Once you have removed the drawer ensure the slides are pushed back so they are fully closed A WARNING Never close the door while the telescopic slides are extended This may damage the slide and or refrigerator or cause the slide to become disengaged from the refrigerator e To replace the drawer 1 With the telescopic slides pushed in all the way 2 Slide the drawer into place over the slides and push the bin in until it stops The bin will not be closed all the way 8 Open the bin to access the finger tabs at the ends of the telescopic slides on each side of the bin Using your thumb and forefinger lift the bin over the end of the slide and clip in place If the drawer is not fully engaged on the slide it s possible the drawer won t stay on the slide if fully extended The end of slide must e clipped into place gt 4 Fully close the bin When replacing the drawers after cleaning we recommend fitting the lower drawer first Freezer baskets built in freezer only Freezer baskets and a freezer shelf are fitted to built in freezers Wire baskets are used to provide easy visibility of the contents Both the baskets and the shelf pull out for easy access and have a stop to prevent the basket and shelf being pulled out too
44. nt bottom mount and freezer models and behind the crisper in the all refrigerator models This coil cools and removes moisture from the air inside Avoid placing food against the air vents in the refrigerator as it affects the efficient circulation If the door is opened frequently a light frosting will occasionally occur on the freezer s interior This is normal and will clear after a few days If the freezer door is accidentally kept open a heavy frost will coat the inside walls and should be removed Your new refrigerator uses a high speed compressor along with other energy efficient components which may make unusual sounds These sounds simply indicate your refrigerator is working how it should They include e Compressor running noises e Air movement noise from the small fan motor e Agurgling sound similar to water boiling e Apopping noise heard during automatic defrosting e A clicking noise prior to compressor start up Further details can be found on page 10 i TIPS amp INFORMATION e For top mount refrigerators where the freezer is on top of the fresh food compartment Don t place food forward of the ribs on the freezer floor as it will Keep the door open N A gt NSS SE L772 AIONTOUUULAN ii Sensor Air vents eee l e For bottom mount refrigerators where the freezer is below the fresh food compartment single door refrigerators and single door vertical freezers Ensure
45. r If live components come into contact with condensing steam they may short circuit or cause an electric shock e Door seals Take care to keep door seals clean Sticky food and drink can cause seals to stick to the cabinet and tear when you open the door Wash seal with a mild detergent and warm water Rinse thoroughly and dry A CAUTION Never use hot water solvents commercial kitchen cleaners aerosol cleaners metal polishes caustic or abrasive cleaners or scourers to clean this appliance as they will damage it Many commercially available cleaning products and detergents contain solvents that will damage your refrigerator When cleaning use only a soft cloth with an unscented mild soap and lukewarm water 25 TROUBLESHOOTING If you think something may be wrong with your refrigerator you can carry out some easy checks before calling for service You may locate the problem sparing yourself from inconvenience saving time and money problem Refrigerator is not operating When there is refrigerator freezer noise If there are odours inside the refrigerator When the motor seems to run more than expected If the temperature in the refrigerator is too warm If the temperature in the refrigerator is too cold If heavy frosting occurs in the freezer If water drips on the floor Fridge does not exit vacation mode If the doors will not close When temperature is hot warm on the outside an
46. r advice Water is to be connected as per diagram below G kitchen cupboard Step 1 Ensure that the ice maker and water dispenser are switched OFF SELECT Boost Fast Ice Vacation DISPLAY MODES DRINKS LOCK CHILL Hold 3sec amp WATER at OFF orf 3sec Replace Filter Step 2 Disconnect refrigerator from power supply Step 3 Connect tap fitting to water supply tap Tap must be close to the refrigerator cs Step 4 Install brackets for filter close to tap Plan to leave as much tubing as possible behind the refrigerator to enable it to be moved easily for cleaning or service A CAUTION Do not screw the brackets into the refrigerator as this may void your warranty and permanently damage the refrigerator Step 5 Write date on filter The filter will need to be replaced every 12 months Step 6 Extend the collar and clip a circlip around the collar at both ends of the filter 13 ICE amp WATER INSTALLATION Step 7 Step 12 Fit filter to brackets with water flow arrow pointing up Turn on water and check all joints and tubes for leaks Step 8 Push shorter tube into tap fitting past insertion mark Step 13 Reconnect the power Step 9 Push other end into filter INLET Step 14 Move the refrigerator back into place being careful not to kink or split the tubing Step 10 Connect remaining tube length into f
47. remain in the tube Replace filter at suggested intervals to avoid water ice reduction and irregularities in taste Remove and clean ice bin once a month discarding unused ice cubes This will ensure fresh clean ice and smooth operation of your ice maker Step 16 Switch ON Ice Maker Clean and empty the dispenser drip tray regularly to avoid overflow As the water cut off is not instant leave glass under dispenser briefly until water has stopped flowing to SELECT avoid spills If you have not used the dispenser for some time e Discard the first seven or eight cups of water E PORN E A e Discard any ice that the ice maker produces in the l first 24 hours contaminants could have settled in DISPLAY MODES DRINKS the water pipes LOCK Pi CHILL Step 17 After 24 hours remove ice bin and dispose of first few batches of ice to ensure that impurities have been flushed from the system The electronic display panel consists of an LCD display with black backlighting and 6 touch buttons When the power is first turned on the display with backlighting will come on If no buttons have been pressed and the fridge door is closed the backlighting will turn off after 30 seconds NOTE If no buttons have been pressed for approximately 60 seconds there may be a delay of up to 2 seconds before the display reacts This is normal and is to prevent accidental changes to settings Controlling the
48. ssurised aerosol containers bear the word flammable and or a small flame symbol do not store them inside any refrigerator or freezer If you do so you may cause an explosion WARNING e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are being supervised or have been given instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance e Don t use a steam cleaner If live components come into contact with condensing steam they may short circuit or cause an electric shock e Do not use mechanical devices or other means to accelerate the defrosting process other than those recommended by the manufacturer e This appliance contains insulation formed with flammable blowing gases Avoid safety hazards by carefully disposing of this appliance R600a refrigerant warning e This appliance contains flammable R600a refrigerant Avoid safety hazards by carefully installing handling servicing and disposing of this appliance e Ensure that the tubing of the refrigerant circuit is not damaged during transportation and installation e Inthe event any damage accidentally occurs keep the appliance away from open fires and any devices that produce sparks or arcs and luminaries during normal or abnorma
49. t models and to 450mm for the all refrigerator model to allow full access to the bins contents as well as bin removal em Recommended airspace sjepow JamMeup a1doosaja p 6 Asea 10 WWUQgS CABINET DOOR NOTE Doors are designed to sit proud of cabinetry not flush The clearances shown above are the recommended minimum clearances The clearance at the rear must not exceed 75mm A WARNING Automatic aerosol systems such as insect control should not be located adjacent to the product as the spray may cause long term damage to the external plastics of the appliance Installing your refrigerator Your new refrigerator should arrive with the front adjustable rollers wound down to tilt the top backwards by about 10mm from upright This will allow your refrigerator door to self close providing a consistent closed seal 10 15mm Fixed rear rollers Height adjustable front rollers The stability foot should also be wound fully up so it will not interfere with the operation of the rollers see diagram in Step 3 A CAUTION The rollers are designed for forward or backward movement only They are not castors Moving the refrigerator sideways may damage your floor and the rollers 1 Roll the refrigerator into place 2 The top of the refrigerator should be tilted back by 10mm see diagram on left This will allow the doors to self close providing a consistent door seal 3 Ifthe refrig
50. t with a bulb that is the same as the original If when you remove the light bulb the small rubber O ring comes out with the bulb fit the O ring over the new bulb and screw bulb into the socket See diagram below Ensure the O ring is in place before replacing the bulb light bulb O ring light socket A WARNING Never insert your finger into the light bulb socket to check for the presence of the O ring 4 Replace the light cover by hooking the light cover lugs into the front of the housing and pressing the rear of the cover up until it clips in 5 Wait 5 minutes to ensure pressures in the refrigeration system are equalized Then reconnect and turn the refrigerator on at the power point LED lighting Electronic models Your refrigerator is fitted with long life LED lighting In the unlikely event the LED lights should fail then the LED lights should be serviced by the manufacturer it s service agent or similarly qualified technician Refer to the warranty page for contact details Cleaning the appliance A WARNING BEFORE CLEANING Turn appliance off at the power point then remove power cord from socket This will make sure there is no chance of getting an electric shock e Doors and exterior stainless steel Your stainless steel appliance is manufactured from a mark resistant stainless steel This stainless steel has a special advanced protective coating that eases the removal of m
51. ter filter in an area of direct sunlight TOP MOUNT FREEZER MODEL TM a A N 2 m y Ay A wn ll INDUC H SSS mE 6j a e oO a gt a H a _ TE a it 6 gt 24 J j a 17 Z Note Product illustrations demonstrate various features but may not be completely in line with current products BOTTOM MOUNT FREEZER MODEL BM Note Product illustrations demonstrate various features but may not be completely in line with current products OMAN Oat WD a no Sensor electronic models only Freezer light electronic models only Freezer air delivery vents Adjustable Spillsafe glass shelf Twist ice amp serve with ice cube trays Freezer air return vents Sensor electronic models only Deodoriser Fridge and freezer temperature controls manual control models Adjustable Spillsafe glass shelves Spillsafe slide away shelf where fitted Fridge light Bottle caddy
52. the freezer Once ice has formed approximately 3 hours simply twist the knob at the front clockwise until the ice drops into the bin below N y A larger bin is provided in some bottom mount models along with an ice scoop Mounting the twist amp serve ice to the other side of the freezer top mount and built in freezer models only 1 Remove the ice bin and ice cube tray If the ice tray assembly is frozen to the carriage simply squeeze the tray and shelf together to break the ice 2 Before you remove the ice carriage remember to disengage it from the glass shelf as shown as it may result in damage to the assembly 3 Remove the centre runner by disengaging it at the front of the shelf and removing it from the rear 4 Refit the runner in to the rear of the shelf on the right hand side and then engage the front as shown 23 CARE AND MAINTENANCE A WARNING Before changing any light bulb switch the power off at the power point and remove the power cord from the power point Changing the light bulb Manual models e Refrigerator light 1 Switch off the power at the power point and remove the refrigerator s power cord from the power point 2 Remove shelves Using a flat blade screwdriver push clips down while pulling the lens forward Carefully unclip the light cover You do this by pulling the upper part of the cover towards the front of the cabinet 4 Unscrew the light bulb and replace
53. tinuously for 10 seconds Door alarm If the fridge door is left open for more than two minutes the alarm will buzz and an arrow pointing to an open door will flash along with the temperature setting and bar graph If you want to leave the door open while you load the refrigerator you can turn the alarm off for 8 minutes by pressing the alarm reset button Child Lock OREG Press and hold the freezer and am fridge buttons together to activate w h the child lock This will disable the display to prevent accidental changes to settings To turn the child lock off press and hold the freezer and fridge buttons together Drinks chill timer The drinks chill timer is used to quickly chill A a bottle Place the bottle in the freezer and mm the timer can be set for a minimum of 5 minutes to a maximum of 30 minutes To set simply press the drinks chill button repeatedly for the number of minutes in 5 minute intervals Once set an animated icon appears beside the drinks chill button with a timer that counts down one minute at a time You can change the time or turn the timer off even after the countdown has started A buzzer will tell you when the time is finished and the icon will flash until the alarm reset button is pressed If your drink is not cold enough reset the drinks chill function remembering the drink is already partially chilled Suggested chilling times e 10 minutes for cans of drink e 20 minutes for bot
54. tles of wine e 30 minutes for bottles of soft drink WARNING Ensure that bottles are not left in the freezer for longer than needed as freezing may cause the bottle to break Energy efficiency Your refrigerator has been designed to be energy efficient and can operate in three modes Normal Eco and Holiday e Normal mode EJ normal Normal mode is used when the refrigerator door is often opened It s the default mode of your refrigerator Eco mode can be used if you don t open your refrigerator door a lot It is activated in one of two ways by manually pressing the eco holiday button once when in normal mode or by automatically activating after 30 hours if the refrigerator door has not been opened The leaf icon will appear on the electronic display when eco mode is on If eco mode is activated automatically the refrigerator will revert to normal mode once the refrigerator door is opened If eco mode is entered manually opening the door will not revert it back to normal mode To exit eco mode simply press the eco holiday button until the word normal is displayed Use Eco mode when you re not using the refrigerator all the time eg as a long term storage refrigerator If the door is going to be opened a lot switch back to normal mode Remember if eco mode is turned on manually it won t switch off automatically ELECTRONIC DISPLAY CONTROLS ELECTRONIC MODELS e Holiday mod
55. ve the crisper bin s by pulling forward then up and forward again lifting the bin off the slides Push the slides back into the refrigerator AN WARNING Never close the door while the telescopic slides are extended It may damage the slide and or the refrigerator or cause the slide to become disengaged from the refrigerator A WARNING To clean a crisper cover with telescopic extension slides simply wipe with a damp cloth and warm soapy water Never immerse the cover in water as this could affect the operation of the slide e To refit see diagram on next page 1 With the runners pushed in all the way 2 Slide the bin into place over the telescopic slides and under the shelf Push the bin in until it stops noting that the bin will not be closed all the way 8 Open the bin to access the finger tabs at the ends on each side of the bin Use your thumb and forefinger to lift the bin over the end of the slide and clip in place 4 Fully close the bin USING YOUR APPLIANCE A WARNING Never store solvents or flammable materials like nail polish remover or lighter fluid inside your refrigerator They will affect the life of the plastic components and may taint stored food Door storage bins The top mount models bottom mount freezer model and all refrigerator models are fitted with door storage bins These bins adjust to meet different storage needs All the door bins are completely removable for cleaning If you want to
56. void misuse and hazards We recommend that you keep this instruction booklet for future reference and pass it on to any future owners i IMPORTANT Check for any damage or marks If you find the refrigerator is damaged or marked you must report it within 7 days if you wish to claim for damage marks under the manufacturer s warranty This does not affect your statutory rights INFORMATION ON DISPOSAL FOR USERS ws ENVIRONMENT e Most of the packing materials are recyclable Please dispose of those materials marked with the recycle symbol ey through your local recycling depot or by placing them in appropriate collection containers e lf you wish to discard this product please contact your local authorities and ask for the correct method of disposal e Local authorities will have the latest information regarding safe disposal of the product e Incorrect disposal may expose the user to injury from sharp objects flammable gasses or cause environmental damage e Refrigerant gasses within the unit should only be discharged by qualified persons A licence may be required by your local authorities to discharge or reclaim the refrigerant gasses Incorrect discharge of gasses may expose the user to injury from flammable gasses or cause environmental damage A WARNING When you dispose of your old refrigerators or freezers remove any doors Children can suffocate if they get trapped inside a discarded unit AN WARNING If pre
57. with the next press of the button 17 ELECTRONIC DISPLAY CONTROLS ICE amp WATER MODELS Changing the refrigerator temperature SELECT C Press the Select button until the food compartment is illuminated on the refrigerator icon Use the arrows to the left and right of the display to select a higher or lower temperature in 1 steps Once O c is reached the display will return to 7 c with the next press of the button Boost function Replace Filter Use the boost function when you add a large amount of food to the fridge compartment To use this function press the Modes button until Boost is illuminated Boost function chills the food quickly but does not affect the temperature in the freezer compartment The boost function will operate for 90 minutes before automatically returning to normal operation If you want to turn the boost off before 90 minutes have passed simply press the Modes button again until the Boost icon disappears and the refrigerator will return to normal operation Freezer temperature alarm If the alarm sounds for no apparent reason check whether anything is keeping the door open If the freezer becomes too warm due to the freezer door being left open or warm food being placed too close to the temperature sensor a buzzer will sound If the freezer temperature alarm sounds press any button to disable the alarm Make sure nothing is holding the freezer door open and move any warm food away
Download Pdf Manuals
Related Search