Ultra-Lite and Lite Qseven Carrier Boards
Contents
1. Jumper Function Ji Qseven 5V Standby power J3 LVDS Power selection J7 Miscellaneous operations J5 LVDS Backlight voltage selection J4 Power up configuration J8 USB Client Host and RS232 Mux Location Connection P1 Q7 P2A SATA 1 P2B SATA 2 P3A USB Ports 1 and 2 P3B USB Ports 3 and 4 P4 LVDS Display P5 LVDS Backlight Power P6 Molex 4 position DC Power P7 Optional Screw Term DC Power P8A miniPCle 1 P8B miniPCle 2 P9 JTAG RS232 Debug P10A SIMCard 1 P10B SIMCard 2 P11A LED header for miniPCle 1 SATA P11B LED header for miniPCle 2 Power P14 HDMI P15 GB Ethernet P16 USB Client Port P17 RS232 P18 Micro SD Card P19 12C Battery Interface 14 Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Ultra Lite Carrier Connector Descriptions Qseven Module Interface Description The processor and chipset are implemented on the Qseven CPU module which connects to the Qseven carrier via a MXM connector Many of the existing Qseven modules use the Intel AtomTM mobile architecture Z series processor SCH US15W chipset The Qseven carrier implements a subset of the Qseven features as described in the introduction For a list of Qseven module vendors visit http www qseven standard org Comnector Function Qseven interface Location Pl Type MXM Foxconn AS0B326 S78N 7F or equivalent Pinout Refer to2. Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual J3 Miscellaneous Functions Function Miscellaneous Functions Location J3 Type 2x3 2 mm Pinout Position Description 1 2 Momentary in will generate a reset pulse via PWGRIN signal on Q7 Module PWGRIN will be pulsed 3 4 Connection for external battery 5 6 QCG015 only Passive level translation for the HDMI video output lt is recommended that this jumper be left installed Revision 0 03 27 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual UltraLite Carrier Hardware Installation 1 Ensure all external system power supplies are off 2 Install the Qseven module into P1 Be sure to follow the manufacturer s direction for proper heatsink heatspreader installation and any other cooling instructions from the manufacturer 3 Connect Tech Qseven carriers are equipment with tw ECM00870 L standoffs height 5mm thread M2 5 for the purpose of securing the Qseven module and head spreader to the Qseven carrier 4 Verify all jumper settings from the relevant sections paying special attention the power selection jumpers Some typical settings are outlined below Jumper Selection Position Function UltraLite Ji Qseven Standby Power 5VSB 1 2 QCG005 only J2 Power Up Control Power Good Delay 4 6 J2 LVDS backlight enable polarity positive 1 2 Off
3. J6 LVDS Backlight Power 12V 2 3 J10 LVDS panel power 3 3V 2 3 5 Install the necessary cables for the application At a minimum this would include a Power cable b Video display cable LVDS and or HDMI c Keyboard and mouse via USB For the relevant cables see the Cables amp Interconnect section of this manual 6 Connect the appropriate I O peripherals to the interface cables keyboard mouse LVDS Display SATA Disk USB boot disk etc 7 Connect the power cable to power supply 8 Switch on the power supply DO NOT power up your Qseven system by plugging in live power 28 Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Lite Carrier Connector Descriptions Qseven Module Interface Description The processor and chipset are implemented on the Qseven CPU module which connects to the Qseven carrier via a MXM connector Many of the existing Qseven modules use the Intel AtomTM mobile architecture Z series processor SCH US15W chipset The Qseven carrier implements a subset of the Qseven features as described in the introduction For a list of Qseven module vendors visit http www qseven standard org Connector Function Qseven interface Location Pl Type MXM Foxconn AS0B326 S78N 7F or equivalent Pinout Refer to Qseven specification Video The availability of the graphics interfaces depends on the Qseven module selected US15W
4. The US15W chipset provides GMA 500 graphics sub system and provides two display interfaces SDVO serial digital video output and LVDS low voltage differential signalling The resolution generated by the GMA 500 is limited 1280x 1024 The configuration of either interface as the primary or secondary display depends on the Qseven module s BIOS capabilities and settings Refer to the Qseven module s documentation for more details HDMI Function HDMI Location P14 Type Standard HDMI Type A Revision 0 03 29 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual LVDS Description The Qseven carrier provides dual 18 or 24 bit LVDS display channels via P4 which are connected directly from the Qseven module LVDS panel supply power is selected with jumper J104 and backlight power is selected with jumper J6 Both are current limited to 500 mA US15W The US15W provides only a single 18 or 24 bit display channel Each LVDS data pair carries two bits each channel has four data pairs LVDS Video Header Function LVDS Graphics Location P4 Type Hirose DF14 30P 1 25H connector Pinout Pin Signal Description 1 VCC_PNL Panel Power 2 VCC_PNL Panel Power 3 GND Digital ground 4 GND Digital ground 5 LVDS A3 N Channel A Data 6 LVDS_A3_P Channel Data r 7 LVDS_CLK_N Channel A Clock LSE 8 LVDS_ACLK_P Channel A Clock 9 GND Digital ground x 10 LVDSA2 N Channel A Dat
5. CTIC 00048 10 CCT 0 1 to DB9M 10 CCT 0 1 DB9 Male Cable drawings are available upon request Send an email to support connecttech com Revision 0 03 45 Dimensions Ultra Lite Qseven Carrier Boards 100mm Picol TX Form factor Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Dimensions Lite Qseven Carrier Board 100mm VK pm Revision 0 03 47 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Part Numbers The following are the base model part numbers for the Ultra Lite and Lite Qseven Carrier Boards Part Number Description Size QCG005 Ultra Lite Qseven Carrier Board Picol TX 100x72mm QCG006 Lite Qseven Carrier Board 100x128mm QCGO11 Ultra Lite Qseven Carrier Board PicolTX 100x72mm w GBE and USB Client QCG015 Ultra Lite Qseven Carrier Board PicolTX 100x72mm w HDMI MSATA GBE microSD RS 232 and USB Client 48 Revision 0 03
6. Qseven specification Video The availability of the graphics interfaces depends on the Qseven module selected US15W The US15W chipset provides GMA 500 graphics sub system and provides two display interfaces SDVO serial digital video output and LVDS low voltage differential signalling The resolution generated by the GMA 500 is limited 1280x 1024 ARM Many of the ARM based Qseven modules support LVDS and HDMI interfaces The configuration of either interface as the primary or secondary display depends on the Qseven module s BIOS capabilities and settings Refer to the Qseven module s documentation for more details HDMI A micro HDMI connector is provided on the QCGO15 carrier Function HDMI Location P14 Type Micro HDMI Type D Revision 0 03 15 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual LVDS LVDS Video is provided on all of the Ultra Lite Qseven Carrier Boards Description The Qseven carrier provides dual 18 or 24 bit LVDS display channels via P4 which are connected directly from the Qseven module LVDS panel supply power is selected with jumper J104 and backlight power is selected with jumper J6 Both are current limited to 500 mA US15W The US15W provides only a single 18 or 24 bit display channel Each LVDS data pair carries two bits each channel has four data pairs LVDS Video Header Function LVDS Graphics Location P4 Type Hir
7. circuit boards in carpeted areas e Try to handle the board by the edges avoiding contact with components 8 Revision 0 03 Product Features Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual FENTE Fe ce ee Part Number QCG005 QCG011 QCG015 QCG006 Size Pico ITX Pico ITX Pico ITX 128x100mm 72x100mm 72x100mm 72x100mm Mini PCle Expansion 1 1 2 mSATA Expansion S 1 SIM Card Connector 1 1 2 USB on MiniPCle Yes Yes LVDS Video amp Yes Yes Yes Yes Backlight controls HDMI Video Audio Yes Yes JTAG RS232 Debug Yes Battery 12C Interface Yes Giga Bit Ethernet Yes Yes Yes USB Client Port Yes Yes Yes USB Ports 4 4 4 an SATA Ports 1 1 1 2 RS232 Serial Port Yes yl SD Card MicroSD MicroSD RTC 3 3V Battery Yes Yes Yes Yes Power Connectors e Molex HDD Yes Yes Optional Yes e Screw Terminal Optional Optional Yes Optional Accessories Optional cable Optional cable Optional cable Optional cable kit kit kit kit M The RS232 serial port and the USB Client Host port are shared with the USB Ports Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual System Block Diagram Atom based Qseven modules implement the core processing features including processor memory and system physical interfaces via the south bridge Many of the Qseven modules are base
8. est ne nes et etes Ed ENEE Eed Power Good Jumper Module Current Requirements caida n O e ooo ia 42 Gurrenit Consumiption imformation A se 42 JS MiscellanE USE UN CONS A e a 42 Lite Carrier Hardware Installation vii eds 43 Windows US15W Specific Cables Ad os Pc es ete ni Dimensions Ultra Lite Qseven Carrier Boards ccccccccsssecesssececeesseeecseneeceeseeeecsesaececseceeeesseeecseaaeeesseneeeeees 46 Dimensions Lite Qseven Carrier Board 47 A nee OA eA DE SR ne RR RRR 48 A Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Customer Support Overview If you experience difficulties after reading the manual and or using the product contact the Connect Tech reseller from which you purchased the product In most cases the reseller can help you with product installation and difficulties In the event that the reseller is unable to resolve your problem our highly qualified support staff can assist you Our support section is available 24 hours a day 7 days a week on our website at www connecttech com sub support support asp See the contact information section below for more information on how to contact us directly Our technical support is always free Contact Information We offer three ways for you to contact us Mail Courier You may contact us by letter at Connect Tech Inc Technical Support 42 Arrow Road Guelph Ontario Canada NIK 156 Email Internet You may conta
9. j d B l USB Ports 3 amp 4 i z E Power Pair PPT Selection NDS Backlight ackil vohaga Selestin GE P12 mSATA SATAO Display Lite Connector and Jumper Summary Connector Summary Jumper Summary QCG005 QCG011 QCG015 Connection Jumper Function P1 P1 Q7 J6 LVDS Backlight voltage selection P2 P2 mSATA P12 SATA 0 J10 LVDS Power selection P2 SATA 1 J2 Power UP Configuration P3A P3A P3A USB Ports 1 and 2 J3 Misc Operations P3B P3B P3B USB Ports 3 and 4 P4 P4 P4 LVDS Display P7 P7 P7 LVDS Backlight Power P9 P9 Molex 4 position DC Power P5 Screw Term DC Power P12 P12 miniPCle P15 P15 SIMCard P11 HDMI P6 P6 GB Ethernet P8 P8 USB Client Port 5 P13 RS 232 P14 Micro SD Card 12 Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Lite Qseven Carrier Board Connector Locations P14 HDMI Type A P17 RS232 Serial Client Mode USB Port Micro SD Card P9 Debug P7 DC Port POWER P3A USB Ports 1 amp 2 P3B USB Ports 3 amp 4 Ethernet Colo IL L IL IL I P7 LVDS P4 LVDS Backlight F Display Lite Bottom iijiiiii ans Revision 0 03 13 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Lite Connector and Jumper Summary Connector Summary Jumper Summary
10. power style connector or optional screw terminal style connectors contact sales connecttech com for more about screw terminal connectors A Panasonic BR1225A FA Lithium battery provides the VBAT for the Qseven module The Qseven carrier generates 3 3V and 1 5V on board for the miniPCle connectors and other circuits 5V only operation is possible if 12V is not required for the LVDS display backlight Power Connectors Function Molex HDD input power Location P6 Type Molex 15244441 R A PCB Connector Pinout Pin Signal Description 1 5V Main Power 2 GND Main Return 3 GND Main Return 4 12V Used for LVDS backlights that require 12VDC Mating connector Molex 0015244048 5VSB Jumper Function 5V SB Location J1 Type 1x3 2 mm Pinout Position Description 1 2 5V SB powered with 5V 3 4 5V SB floating Pins 2 3 have no function Off Floating Revision 0 03 41 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Power Good Jumper Function Power Up Control Location J4 Type 2x3 2 mm Pinout Position Description 1 2 See LVDS backlight 3 4 PWRGIN 10k pullup to 5 0V 5 6 PWGRIN to Q7 module The Power Good signal is delayed 200mS after the 5V 3 3V and 1 5V rails are at their stable nominal values Jumper 5 6 installed is recom
11. supply filtering is provided Assume USB Port numbering starts at USB Port 0 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Connector Function USB 2 0 x2 Locations P3A P3B Type Hirose DF13 8P Pinout Pin Signal Description 1 VCC_USB_0 Port 0 Filtered 5V 2 USB_0_N Port O Data 3 USB Ob Port 0 Data 4 USB_GND_0 Port 0 Filtered Digital Ground 5 USB_GND_1 Port 1 Filtered Digital Ground 6 USB_1_N Port 1 Data 7 USB_1_N Port 1 Data 8 VCC_USB_1 Port 1 Filtered 5V d iech com USB Ports on MiniPCTe connectors On the QCG005 the USB from Mini PCIe is brought out to a Mini USB connector On the QCG011 Host USB Port 5 is wired to the MiniPCle connector Note Assume USB Port numbering starts at 0 Revision 0 03 19 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual RS232 Serial Description The QCG015 UltraLite carrier provides an RS 232 serial port on P13 The serial port is facilitated with a FTDI FT232RQ USB to serial IC Connector amp Jumper Function RS232 Serial Port Locations P13 Type 2x5 2mm vertical header Pinout P17 Pin RS232 Signal 1 NC 2 RXD 3 TXD 4 NC 5 GND 6 NC 7 RTS 8 CTS 9 NC 10 NC Note 1 A standard 9D RS232 pinout can be achieved using a Connect Tech CBG127 cable Note 2 Your operating system will require driver
12. B_GND_0 Port 0 Filtered Digital Ground 5 USB _GND 1 Port 1 Filtered Digital Ground 6 USB IN Port 1 Data 7 USB_1_N Port 1 Data 8 VCC_USB_1 Port 1 Filtered 5V Notel The USB Host Port 1 is multiplexed with the USB Client mode See USB Client Host Mode for more information Note 2 USB Port 3 is multiplexed with the USB UART to provide a RS232 serial port 32 Revision 0 03 USB Client Host Port Mode Port 1 of the Qseven Lite carrier can be configured for either Client mode or Host mode e Host mode is the typical mode of operation It is used to connect items like keyboards and USB memory sticks e Client mode is used to provide an application specific USB connection to the Qseven CPU e Refer to your Qseven module vendor for Client mode software support and operations instructions USB Client Host Operation Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Function Select USB Client Host Operation Location J8 pins 1 2 Type 2x2 2mm jumper block Pinout Position Description 1 2 Off Host Mode On Client Mode Note Jumper should not be installed with power on USB Ports on MiniPCTe connectors USB Port 4 and USB Port 5 are wired to the MiniPCle connectors as follows USB Port 4 MiniPCle 1 USB Port 5 MiniPCle 2 Note Assume USB Port numbering starts at 0 Revision 0 03 33 Connect Tech Ultra Lite and Lite Oseven C
13. CTs Connect Tech Inc Ultra Lite and Lite Qseven Carrier Boards User Manual Connect Tech Inc 42 Arrow Road Guelph Ontario NIK 1S6 Tel 519 836 1291 Toll 800 426 8979 North America only Fax 519 836 4878 Email sales connecttech com support connecttech com Web www connecttech com CTIM 00068 Revision 0 03 Nov 1 2013 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Table of Contents Customer Support OVECVISW EENS NEE SEENEN Eug 5 Contact IOMA ne nee EE T E e i 5 Limited Lifetime Warta yesse rio iei nene E EEE E EE EEE NA E E EEE EE a 6 Copyright Notice enee en E 6 Trademark Acknowledsment osineen e en cie EE E EE a 6 Revision HIStO Vecina 6 prp ED aeseg SEENEN EE EENS 8 Wh tis EE 8 ESD W aiming eelere see PAR RN Ee 8 Product EE 9 System Block DAMA ee ERAN EE 10 Hardware Description Ree ts dE a 11 Ultra Lite Qseven Carrier Board Connector Locations see 11 EL EE ENEE te Re iescht AS e Eege dE ege Ee ed Seene A aueessasevs cease iad aanvsth den adeeesicbstesnceehdetesuadurse ovenkseicats chalets EOE EENE EE EERIE a EE tay Lite Connector and Jumper Summary Lite Qseven Carrier Board Connector Locations sisi 13 Lite e NEE 13 Lite Connector and Jumper SUMMALY ees ere nee ta ne rennes ne gene eee nu 14 Ultra Lite Carrier Connector Description 2 c sccssecysbssssessecscvencosstsnesovscavass sass east sasssesscedsssceboseesceesesaseseesees 15 Os ven Module Interfaces seen n
14. D RESp402 R38 Battery Interface 12CC D 3 3V B 12C D H GND 5 Batlow Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Debug JTAG and RS232 on Lite Version The Lite carrier brings out the Qseven MFG 0 4 pins for JTAG and RS232 debug purposes features on ARM and Tegra based models Function Debug Interface Locations P9 Type 2x5 2mm Header yP 1x3 2mm Jumper Pinout 2x5 Header Pin Signal Pin Signal 1 TRST 2 3 3V 3 TMS 4 NC 5 TDI RX 6 TX_232 7 TDO TX 8 RX_232 9 TCK 10 GND 1x3 Jumper Pin Signal 1 RX_Out 2 TDI RX from Q7 3 TDI signal to Header Circuit Schematic 3 3V ITAG_UART ww mros testo PL AAA ir e d i MFG3 TMS Boot Feet Pro JU raaa MEG2 TI RN ES Pa pq AAA Za ei TAIN gt OUT T2IN gt T20UT RIQUT lt FR1IN R20UT lt ER2IN vec GND GNO SP232AEN 7 GNI GND Revision 0 03 39 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Micro SD Card Description Function Micro SD Card Locations P18 Type Micro SD Card slot Pinout 40 Revision 0 03 Power Description Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual The Lite Qseven carrier is designed to be powered from a 5V and 12V power supply The carrier board feature a standard Molex HDD
15. Lite and Lite Qseven Carrier Boards offer several processor options including Intel Atom Freescale i MX51 TI OMAP and NVIDIA Tegra which are easily upgradable to accommodate future generations Connect Tech s Qseven carrier boards are ideal for compact computing applications in mobile entertainment kiosks digital signage soldier wearable systems and gaming What is Qseven Qseven is an off the shelf multi vendor computer on module that integrates the core components of acommon PC The Qseven standard allows upgrading to the latest processor and memory technology with ease while maintaining the I O interfaces To learn more about Connect Tech s Qseven carrier visit http www connecttech com Qseven ESD Warning Electronic components and circuits are sensitive to ElectroStatic Discharge ESD When handling any circuit board assemblies including Connect Tech Qseven carrier assemblies it is recommended that ESD safety precautions be observed ESD safe best practices include but are not limited to e Leaving circuit boards in their antistatic packaging until they are ready to be installed e Using a grounded wrist strap when handling circuit boards at a minimum you should touch a grounded metal object to dissipate any static charge that may be present on you e Only handling circuit boards in ESD safe areas which may include ESD floor and table mats wrist strap stations and ESD safe lab coats e Avoiding handling
16. V Refer to the display panel s documentation for proper configuration Location J5 Type 1x3 0 100 jumper block Pinout Position Description 1 2 5V 2 3 12V off floating Default 12V Power for LVDS Panel Circuits Function LVDS panel power select Selects either 3 3V or 5V Refer to the display documentation for proper configuration Location Ultralite J10 Lite J3 Type 1x3 0 100 jumper block Pinout Position Description 1 2 5V 2 3 3 3V off floating Default 3 3V Revision 0 03 31 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual LVDS backlight enable polarity Function LVDS backlight enable polarity Selects either positive or negative Refer to the inverter power supply documentation for proper configuration Location J4 Type 1x2 2mm jumper block Pinout Position Description 1 2 Off Positive polarity On Negative polarity Default Positive polarity USB Operations User USB Ports The Lite Qseven carrier implements 4 of the available USB 2 0 connections via two connectors Over current protection and power supply filtering is provided Assume USB Port numbering starts at USB Port d Connector Function USB 2 0 x2 Locations P3A P3B Type Hirose DF13 8P Pinout Pin Signal Description 1 VCC_USB_0 Port 0 Filtered 5V 2 USB_0_N Port O Data 3 USB Ob Port 0 Data 4 US
17. a k 11 LVDS_A2_P Channel A Data 12 LVDS_A1_N Channel A Data 8 13 LVDS_A1_P Channel A Data a 14 LVDS AO N Channel A Data t 15 LVDS AO P Channel A Data x 16 GND Digital ground 17 LVDS B3 N Channel B Data y 18 LVDS B3 P Channel B Data wh 19 LVDS_BCLK_N Channel B Clock a 20 LVDS_BCLK_P Channel B Clock Sp 21 GND Digital ground l 22 LVDS_B2_N Channel B Data 5 23 LVDS_B2_P Channel B Data 24 LVDS_B1_N Channel B Data 25 LVDS_B1_P Channel B Data 26 LVDS_BO_N Channel B Data 27 LVDS_BO_P Channel B Data 28 GND Digital ground 29 LVDS_DID_CLK Display ID Clock 3 3V 30 LVDS_DID_DATA Display ID Data 3 3V 30 Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual LVDS Backlight LVDS Backlight connector Function LVDS backlight power Location P5 Type Hirose DF13 8P 1 25H connector Ln Pin Signal Description 1 12V 12 V DC max 1A 2 12V 12 V DC max 1A 3 5V 5 V DC max 1A 4 5V 5 V DC max 1A Backlight enable S EE level selected with J4 Back light power S SE selected with J6 GND Digital ground GND Digital ground LVDS Backlight Power Jumper Function LVDS backlight power select Selects either 12V or 5
18. arrier Boards User Manual RS232 Serial Description The Lite version of Qseven carrier provides one RS232 serial port on P17 The serial port is facilitated with a FTDI FT232RQ USB to serial IC The USB to Serial IC is multiplexed with USB Port 3 Connector amp Jumper Function RS232 Serial Port Locations P17 and J8 3 4 Type 2x5 0 1 vertical header and 2x2 2mm header Pinout P17 Pin RS232 Signal 1 DCD 2 DSR 3 RXD 4 RTS 5 TXD 6 CTS 7 DTR 8 RI 9 10 NC J8 Jumper USB Mode In USB Host Port Out USB to UART Note Jumper should not be installed with power on Note 1 A standard 9D RS232 pinout can be achieved using a Connect Tech CAG104 cable Note 2 Your operating system will require driver support for this USB UART Some Operating System come equipment with built in support for this part others you will have to install the appropriate drivers Connect Tech does not provide driver support for this part You can download driver support from the FTDI website at www ftdichip com The part number of the IC is the FT232RQ Note3 The RS232 transceiver is the Exar SP3243 It is configured to use the Auto Online mode of operation This means that it will off and not driving signals until any of the inputs RXD CTS RI DSR or DCD detect a voltage This voltage will be provided when you connect the port to your RS232 device 34 Rev
19. ation P5 Type FCI 20020111 C041A01LF or equivalent Pinout Pin Signal Description 1 5V Main Power 2 GND Main Return 3 GND Main Return 4 12V Used for LVDS backlights that require 12VDC Mating connector FCI 20020000 C041BO1LF or equivalent Revision 0 03 25 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual 5VSB Jumper QCG005 Only QCG011 QCG015 permanently conne ct 5V SB to 5V Function 5V SB Location J1 Type 1x3 2 mm Pinout Position Description 1 2 5V SB powered with 5V 3 4 5V SB floating Pins 2 3 have no function Off Floating Power Good Jumper Function Power Up Control Location J2 Type 2x3 2 mm Pinout Position Description 1 2 See LVDS backlight 3 4 PWRGIN 10k pullup to 5 0V 5 6 PWGRIN to Q7 module The Power Good signal is delayed 200mS after the 5V 3 3V and 1 5V rails are at their stable nominal values Jumper 5 6 installed is recommended Module Current Requirements Voltage Current Ultra Lite Current Lite 5V Up to 5A Up to 6 8A 5V Fuse 5A 7A 12V 200mA 200mA Current Consumption information The majority of the current consumption is from the Qseven and or the miniPCIe modules Module Current Qseven Module V1 2 900mA to 1500mA max from 5V rail MiniPCle 2750mA max 3 3V 2020mA from 5V rail 26
20. be photocopied reproduced or translated to another language without the prior written consent of Connect Tech Inc Copyright O 1997 2013 by Connect Tech Inc Trademark Acknowledgment Connect Tech Inc acknowledges all trademarks registered trademarks and or copyrights referred to in this document as the property of their respective owners Not listing all possible trademarks or copyright acknowledgments does not constitute a lack of acknowledgment to the rightful owners of the trademarks and copyrights mentioned in this document Revision History Rev Date Change 0 00 June 3 2011 Original Document 0 01 Oct 3 2012 Updated features for QCG006 including GBE JTAG USB Client Host and RS232 0 02 April 3 2013 Added information on QCGO1 1 12 0 03 Oct 24 2013 Split Ultra Lite and Lite Carrier information added QCGO15 6 Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Revision 0 03 7 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Introduction Connect Tech s Ultra Lite and Lite Qseven Carrier Boards are small low cost feature rich carriers that integrate with any industry standard Qseven module These bus independent carrier boards offer easy connection to SATA USB Ethernet LVDS and VGA video and RS 232 with Mini PCIe and SIM card expansion capability Mini PCle peripherals such as WiFi GPS Bluetooth or storage are optional Ultra
21. ct us through the Internet Our email and URL addresses on the Internet are sales connecttech com support connecttech com www connecttech com Note Please go to the Download Zone or the Knowledge Database in the Support Center on the Connect Tech website for product manuals installation guides device driver software and technical tips Submit your technical support questions to our customer support engineers via the Support Center on the Connect Tech website Telephone Facsimile Technical Support representatives are ready to answer your call Monday through Friday from 8 30 a m to 5 00 p m Eastern Standard Time Our numbers for calls are Toll Free 800 426 8979 North America only Telephone 519 836 1291 Live assistance available 8 30 a m to 5 00 p m EST Monday to Friday Facsimile 519 836 4878 on line 24 hours Revision 0 03 5 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Limited Lifetime Warranty Connect Tech Inc provides a Lifetime Warranty for all Connect Tech Inc products Should this product in Connect Tech Inc s opinion fail to be in good working order during the warranty period Connect Tech Inc will at its option repair or replace this product at no charge provided that the product has not been subjected to abuse misuse accident disaster or non Connect Tech Inc authorized modification or repair You may obtain warranty service by delivering this product to an autho
22. d on the mobile Intel Atom architecture Z series processor SCH US15W chipset shown in the block diagram below This document will generally refer to the features of the US15W PROCESSOR Note Some features shown above may not be present on all part numbers 10 Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Hardware Description Ultra Lite Qseven Carrier Board Connector Locations 0CG005 a ae up LEDS Mi onfig 5885 J1 Q7 Standby Operation P15 SIM Card 222 Power 2226 P13 USB P9 DC miniPCle POWER P3A USB Ports 1 amp 2 P3B Ges USB Ports 3 amp 4 P3C J10 Not installed LVDS Powe Selection J6 NE LVDS Backlight Voltage Selection P7 LVDS P4 LVDS P12 miniPCle Backlight a Display QCG0011 T SE up LEDS J3 Misc ontig 5885 did ae P15 SIM Card 3225 l S550 P9 DC P6 Gigabit Ethernet POWER P8 USB Client P3A P2 USB Ports 1 amp 2 SATA P3B USB Ports 3 amp 4 J10 LVDS Power Selection J6 LVDS Backlight Voltage Selection P7 LVDS P4 LVDS Backlight Display P12 miniPCle Revision 0 03 11 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual OCG0015 Q Q Oe 22 Y 22 4 N J2 P z S T LEDS Power up i J3 Misc Config y e z 5885 Operation 3228 EEES eg P9 DC re Gigabit Ethernet POWER De 4 E P8 USB Client gell P3A P2 CN USB Ports 1 amp 2 SATA lo AB En SATA1 HA Pam C P3B
23. e level selected with J4 Back light power 6 VEC BKE selected with J6 GND Digital ground GND Digital ground LVDS Backlight Power Jumper Function LVDS backlight power select Selects either 12V or 5V Refer to the display panel s documentation for proper configuration Location J6 Type 1x3 0 100 jumper block Pinout Position Description 1 2 5V 2 3 12V off floating Default 12V Power for LVDS Panel Circuits Function LVDS panel power select Selects either 3 3V or 5V Refer to the display documentation for proper configuration Location J10 Type 1x3 0 100 jumper block Pinout Position Description 1 2 5V 2 3 3 3V off floating Default 3 3V Revision 0 03 17 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual LVDS backlight enable polarity Function LVDS backlight enable polarity Selects either positive or negative Refer to the inverter power supply documentation for proper configuration Location J5 Type 1x2 2mm jumper block Pinout Position Description 1 2 Off Positive polarity On Negative polarity Default Positive polarity 18 Revision 0 03 USB Operations User USB Ports The UltraLite carriers implement 4 of the available USB 2 0 connections via two connectors Over current protection and power
24. e A EAR A Ri 26 Module Current Requirement its iia 26 Current Consumption information sisi 26 JS Miscellanedus FUNCION tai 27 Ultralite Carrier Hardware InStall tion 2 5 eee ss nets ne SEENEN EES ENEE 28 Lite Carrier Connector Descriptions 2 sus sms Matt nissan EEE EEEE Ade 29 Oseven Module Interfaces ss ae ns EES EES 29 Description Connector WACO E SR nr ean Beak coe ae ne Re E E HDMI ESS Te AAE ee Re Rene ln EEN AE IR E LVDS Video Header AR E GE LVDS BackKlisht CONNeCtOr eegen ee EES id hadrian ie LVDS Backlight Power Jumper Power for LVDS Panel Circuits LVDS backlisht enable polarity icon nent nt EENEG rentes he Echt 32 USB Operations 212 05 Led M RARE sn MIE SP RE Ne cates RM ed Let ile eet dee 32 User USB Ports E EIDEN E E EE ee USB Client Host Port Mode nan nement mine A RAA USB Client Host Operation USB Ports on MiniPCle connectors RS 232 el AA O enee e dese AE eh den done do deb dedans IR Oe 34 Connector tee 34 e RE 35 KE e EE 35 Connector E LEDS ees E E A es ERR ie 35 MANIP e 36 GOEN Lie 36 MIniPCle WiFi Stats LEDS 0 AE eet Sete Bee Donna Ee 37 Off boardistatus LEDS veda data 37 Batty and DEA a 38 A eene 38 Debug JTAG and RS232 0n Lite Versions essentiel een ad 39 EEN ett Lei e 39 Micro LEE 40 IR EE 40 EE ee E E EE Ee 41 DESC E Power Connectors Revision 0 03 3 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual A sans tiens E tnt ren
25. even carriers have 1 miniPCIe connectors Function miniPCIe Locations Ultra Lite P12 Type Molex miniPCIe miniPCIe SIM Card The QCG005 and QCG011 Qseven carriers also have 1 miniPCIe SIM Card connector Function SIM Card Locations P15 Type FCI Hinged PN 7112S0825X01LF Pinout Pin Signal 1 3 3V 2 Reset 3 CLK 4 C4 5 GND 6 VPP 7 DATA 8 C8 22 Revision 0 03 miniPCle WiFi Status LEDs The QCG005 and QCG011 Qseven carriers have a set of status LEDs Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Function Status LEDs Locations Ultra Lite D7 D8 D9 LED Function D7 WWAN D8 WLAN D9 WPAN miniPCle WiFi Jumpers Function W_DISABLE Locations P10D Jumper Function IN Radio Disabled OUT Radio Enabled Off board status LEDs The QCG005 and QCGO011 Qseven carriers feature a 2mm header which can be used to power off board LEDs Ultra Lite Version Function Off Board LEDs Locations P10 Odd Anode V Even Cathode Header Pins Function P10 A WWAN P10 B WLAN P10 C WPAN Note Odd pins are connected to 3 3V or 5V with a 470ohm resistor Revision 0 03 23 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Micro SD Ca
26. ision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual SATA Description The Qseven carrier provides 1 or 2 SATA host connections USI5W Some Qseven modules based on the US15W convert the US15W s IDE interface to one SATA connection as IDE master and one built in NAND based flash drive as IDE slave Consult the Qseven module s documentation for more information In this case only P10A connector is active Connector amp LEDs Function SATA host Locations Lite P2A P2B Type Industry standard right angle SATA host connector Molex 0470804005 or equivalent Pinout Pin Signal 1 GND 2 SATA_TX_P 3 SATA_TX_N 4 GND 5 SATA_RX_N 6 SATA_RX_P 7 GND Function SATA Status LEDs Lite Location Dl 0 5 0018 RUE ur org E Revision 0 03 35 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual miniPCle The Qseven carrier has 2 miniPCIe connectors Function miniPCle Lite Locations P8A P8B T Molex ype miniPCle miniPCle SIM Card The Qseven carrier has 2 miniPCle SIM Card connectors Function SIM Card Locations P10A P10B Type FCI Hinged PN 711250825X01LF Pinout Pin Signal 1 3 3V 2 Reset 3 CLK 4 C4 5 GND 6 VPP 7 DATA 8 C8 36 Revision 0 03 miniPCle WiFi Status LEDs Connec
27. mended Module Current Requirements Voltage Current Ultra Lite Current Lite 5V Up to 5A Up to 6 8A 5V Fuse 5A 7A 12V 200mA 200mA Current Consumption information The majority of the current consumption is from the Qseven and the miniPCIe modules Module Current Qseven Module V1 2 900mA to 1500mA max from 5V rail MiniPCle 2750mA max 3 3V 2020mA from 5V rail J3 Miscellaneous Functions Function Miscellaneous Functions Location J7 Type 2x3 2 mm Pinout Position Description 1 2 Momentary in will generate a reset pulse via PWGRIN signal on Q7 Module PWGRIN will be pulsed 3 4 Connection for external battery 5 6 Ultralite No function Lite PWRBTN to Q7 module 42 Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Lite Carrier Hardware Installation 9 Ensure all external system power supplies are off 10 Install the Qseven module into P1 Be sure to follow the manufacturer s direction for proper heatsink heatspreader installation and any other cooling instructions from the manufacturer 11 Connect Tech Qseven carriers are equipment with two ECM00870 L standoffs height 5mm thread M2 5 for the purpose of securing the Qseven module and head spreader to the Qseven carrier 12 Verify all jumper settings from the relevant sections paying special attention the power selection j
28. ose DF14 30P 1 25H connector Pinout Pin Signal Description 1 VCC_PNL Panel Power 2 VCC_PNL Panel Power 3 GND Digital ground 4 GND Digital ground 5 LVDS A3 N Channel A Data 6 LVDS A3 P Channel Data L 7 LVDS_CLK_N Channel A Clock MA 8 LVDS_ACLK_P Channel A Clock gt 9 GND Digital ground n 10 LVDS_A2_N Channel A Data e 11 LVDS A2 P Channel A Data 12 LVDS_A1_N Channel A Data 8 13 LVDS_A1_P Channel A Data 14 LVDS AO N Channel A Data t 15 LVDS AO P Channel A Data 16 GND Digital ground 17 LVDS B3 N Channel B Data y 18 LVDS B3 P Channel B Data Wi 19 LVDS_BCLK_N Channel B Clock H x 20 LVDS_BCLK_P Channel B Clock d 21 GND Digital ground l 22 LVDS_B2_N Channel B Data hi 23 LVDS B2 P Channel B Data 24 LVDS B1_N Channel B Data 25 LVDS B1 P Channel B Data 26 LVDS DON Channel B Data 27 LVDS BO P Channel B Data 28 GND Digital ground 29 LVDS DID CLK Display ID Clock 3 3V 30 LVDS DID DATA Display ID Data 3 3V 16 Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual LVDS Backlight LVDS Backlight connector Function LVDS backlight power Location P7 Type Hirose DF13 8P 1 25H connector Pinout Pin Signal Description 1 12V 12 V DC max 1A 2 12V 12 V DC max 1A 3 5V 5 V DC max 1A 4 5V 5 V DC max 1A 5 LVDS_BLEN Backlight enabl
29. rd Description A standard MicroSD card slot is provided on the QCG015 UltraLite carrier Function Micro SD Card Locations P14 Type Micro SD Card slot Pinout 24 Revision 0 03 Power Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Description The Ultra Lite Qseven carriers are designed to be powered from a 5V and 12V power supply The QCG011 and QCGN11 carrier boards feature a standard Molex HDD power style connector the QCG015 features a screw terminal style connector Both connector styles are available for all carriers for more information on modifying the power input connector to suit your requirements please contact sales A Panasonic BR1225A FA Lithium battery provides the VBAT for the Qseven module The Qseven carrier generates 3 3V and 1 5V on board for the miniPCle connectors and other circuits 5V only operation is possible if 12V is not required for the LVDS display backlight Power Connectors Function Molex HDD input power QCG005 QCG011 QCG005 QCG011 Location P9 RE QE SE Type Molex 15244441 R A PCB Connector Pinout Pin Signal Description 1 5V Main Power 2 GND Main Return 3 GND Main Return 4 12V Used for LVDS backlights that require 12VDC Mating connector Molex 0015244048 or equivalent Function Screw Terminal Input Power QCG015 Loc
30. rized Connect Tech Inc business partner or to Connect Tech Inc along with proof of purchase Product returned to Connect Tech Inc must be pre authorized by Connect Tech Inc with an RMA Return Material Authorization number marked on the outside of the package and sent prepaid insured and packaged for safe shipment Connect Tech Inc will return this product by prepaid ground shipment service The Connect Tech Inc Lifetime Warranty is defined as the serviceable life of the product This is defined as the period during which all components are available Should the product prove to be irreparable Connect Tech Inc reserves the right to substitute an equivalent product if available or to retract Lifetime Warranty if no replacement is available The above warranty is the only warranty authorized by Connect Tech Inc Under no circumstances will Connect Tech Inc be liable in any way for any damages including any lost profits lost savings or other incidental or consequential damages arising out of the use of or inability to use such product Copyright Notice The information contained in this document is subject to change without notice Connect Tech Inc shall not be liable for errors contained herein or for incidental consequential damages in connection with the furnishing performance or use of this material This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may
31. s haters dr ads ened eae See D 15 DE SCHIP TEE 15 RNA EE EE aie es Ra er nt AER 15 Kat 15 DM entente it cd Rares A RAS Line Elie nl ten ii 15 EDS ne na A rr e ence erect ne de ere Prone Tr irre E RS RM tt me 16 IR EE 16 LVDS Video Herder A Ai 16 EN Die Backlightss shine sien led ten coh bee bokeh tdi deleted 17 EVDS BackliSht Connector ns ii ne 17 LVDS Backlight Power Jumper este EE ii 17 Power for LVDS Panel Cirouits E 17 EVDS backlisht nabl polarity EEN 18 WSB Operations TE 19 User USB Ports ucraniana EEE E dep eeaeeeenteade doves ce nchinbtedepeesasechdecdetobatcuseevestsedebeseustosesnleteans este 19 Comet senc cole Cua ere Re eeh Ee Me 19 USB Ports on MiniPCle Conecto S nea n a A EEE E EES EEA EE E E EESE O ERENS 19 III EE 20 IR OTT 20 Connector Ge JUDE ST En den M Pen eee nes 20 SATA gengen aid dr net le Ee sole dre 21 IR E 21 Connector SLEDS E 21 O EC 22 mimPCIeSIMCard ME 22 MINIP CS WiFi Status LEDS cai iia aee etes aien 23 2 Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual miniPCIe WiFi EE 23 Off board status LEDS bersisir tte eee eea eare e e ae LE n n aee ea eiiean ia 23 Ultra Late EE 23 Note Odd pins are connected to 3 3V or 5V with a 470ohm resistor Micro SD Card 23 Re EE 24 e 25 YA e EE 25 PoOWerCOmmnectons etica EES le le ent Man te A ne 25 5VSB Jumper QCG005 Only QCG011 QCG015 permanently connect 5V SB to 5V neseser 26 Power Good TUNEL in EE A
32. support for this USB UART Some Operating System come equipment with built in support for this part others you will have to install the appropriate drivers Connect Tech does not provide driver support for this part You can download driver support from the FTDI website at www ftdichip com The part number of the IC is the FT232RQ 20 Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual SATA Description The Qseven carrier provides 1 SATA host connection On the QCG005 and QCGO11 carriers this is connected to SATAO on the QCG015 it is connected to SATA1 USI5W Some Qseven modules based on the US15W convert the US15W s IDE interface to one SATA connection as IDE master and one built in NAND based flash drive as IDE slave In these configurations only SATAO is brought out to the carrier Consult the Qseven module s documentation for more information Connector amp LEDs Function SATA host QCG005 QCG011 Locations P2 Type Industry standard right angle SATA host connector QCG015 Molex 0470804005 or equivalent Pinout Pin Signal 1 GND 2 SATA_TX_P 3 SATA_TX_N 4 GND 5 SATA_RX_N 6 SATA_RX_P 7 GND Function SATA Status LEDs Ultra Lite Location Dl Revision 0 03 21 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual miniPCle The QCG005 and QCG011 Qs
33. t Tech Ultra Lite and Lite Oseven Carrier Boards User Manual The Qseven carrier has 2 sets of status LEDs Function Status LEDs Locations D7A D8A D9A D7B D8B D9B LED Function D7A D7B WWAN D8A D8B WLAN D9A D9B WPAN Off board status LEDs The Qseven carrier features 2mm headers which can be used to power off board LEDs Function Off Board LEDs Locations P11A and P11B Odd Anode V Even Cathode Header Pins Function P11 A B A SATA Activity 5V Pwr P11 A B B NC 3 3V Pwr P11 A B C WWAN P11 A B D WLAN P11 A B E WPAN Note Odd pins are connected to 3 3V or 5V with a 470ohm resistor Revision 0 03 37 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Battery and DC Interface Function Battery and DC Interface Locations P19 Type 1x5 0 1 Header Pinout Pin Signal 1 12C Clk 2 3 3V 3 12C Data 4 GND 5 BATLOW Note The BATLOW signal is pulled to GND on the PCB The BATLOW signal must be driven high by the battery circuit when battery level is normal Partial Schematic Battery_Int Ps Q7_12C_C Q RCD lt _Bat_Intric Aen 38 Bat_low Ki 3 G NC7SO8P5X BATLOW Vin 3 6V B 3Vin 2 4V C7SO8PSX Vin High at 3 3V 31V The circuit should work at 3 3V or SV input GN
34. tp edc intel com Software Downloads IEGD compatibility Other distributions such as Linux are supported through the open source community Windows US15W Specific Graphics In some cases the secondary LVDS display will appear washed out to avoid this ensure the correct version of the IEGD is installed 44 Revision 0 03 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Cables amp Interconnect The following table summarizes the Qseven carrier s headers and lists the matching cables included with the optional cable kit CKG001 Cable Part Drawing ET PCB Connector Number Number Description PCB End Interface End Hirose Hirose DF13 8P CBG071 CTIC 00182 USB dual USB 2 0 Type female DF13A 8S 1 25C 1 25H 50 Hirose Hirose DF14 30P CBG076 CTIC 00196 LVDS un terminated DF14 30S 1 25C N A 1 25H 25 Hirose Hirose DF13 8P CBG078 CTIC 00198 Backlight un terminated N A DF13A 8S 1 25C 1 25H 50 Mo ex CBG079 CTIC 00199 SATA SATA SATA 470804005 Samtec CBG080 CTIC 00200 Reset Button 1x2 2mm socket Momentary Pushbutton TMM 102 02 L S y 10 pin 2mm Pitch CaGoes CTIC 00181 Gigabit Ethernet Cable 10 pin 2mrn Pitch RJ 45 Header Header Standard HDMI cable not HDMI Type A NA NA provided by Connect HDMI Type A HDMI Type A Tech Inc Other cables Cable Part Drawing HE PCB Connector Number NUMBER Description PCB End Interface End 2x5 0 1 header CAG104
35. umpers Some typical settings are outlined below Jumper Function Selection Position Ji Qseven Standby Power 5VSB 1 2 J7 Power Up Control Power Good Delay 4 6 J7 LVDS backlight enable polarity positive 1 2 Off J5 LVDS Backlight Power 12V 2 3 J3 LVDS panel power 3 3V 2 3 13 Install the necessary cables for the application At a minimum this would include d Power cable e Video display cable LVDS and or HDMI f Keyboard and mouse via USB For the relevant cables see the Cables amp Interconnect section of this manual 14 Connect the appropriate I O peripherals to the interface cables keyboard mouse LVDS Display SATA Disk USB boot disk etc 15 Connect the power cable to power supply 16 Switch on the power supply DO NOT power up your Qseven system by plugging in live power Revision 0 03 43 Connect Tech Ultra Lite and Lite Oseven Carrier Boards User Manual Software Installation amp Configuration In general always refer to the Qseven module s manual for proper installation of software drivers and configuration software as well as for appropriate BIOS settings The following sections provides some specific notes and hints for successful module integration Operating System Notes Linux US15W Specific Graphics Intel Driver support for the Poulsbo GMA500 is limited to several distributions Redhat Fedora See IEGD Intel Embedded Graphics Driver website for details ht
Download Pdf Manuals
Related Search