TECDIS USER MANUAL
Contents
1. System rudder limit to min value during min radius turn rudder limit is not available 5 Disconnect serial Emits alarm and stops TCS function Remove Track link to heading simultaneously It automatically Control connection controller during switches to Radius mode and manual from ECDIS while straight leg maneuver will be in effect sailing straight ahead 6 Disconnect serial Emits alarm and stops TCS function Remove signal link to heading simultaneously Automatically switches cable exclusively in controller during to Radius mode and manual maneuver use for Auto Pilot turn will be in effect after turning to the pre outputted from determined maximum degree ECDIS while turning 7 Disconnect speed log Although emits alarm two position Remove LOG input during straight leg sensor data inputted maintains the outputted to ECDIS or turn normal function while turning 8 Simulate failure in Same as item 5 or 6 Turn off ECDIS ECDIS 9 Simulate failure in Not influential Turn off Conning conning display Display 10 Disconnect rudder Emits alarm by Alarm System If the Remove rudder feedback deviation between order rudder angle feedback input and actual rudder angle is 5deg or more outputted to Alarm the Alarm System emits alarm and System while freezes the actual rudder angle at this turning time This test is dangerous 11 Simulate failure in Emits alarm by Alarm System and stops Remove2. 2 Good ONG ON A Page 82 TECDIS Installation Manual Before start TEST routes must be created or transferred from other TECDIS 1 Press the Plan key icon with number 1 indicated is active This means primary route will be selected Choose a route with boathook icon TECDIS 1 2 Press YES icon to activate route g Route Monitoring8 Route is then shown on displayed charts Good ONG ON A 4 To display secondary route choose icon with button 2 TECDIS 2 indicated Repeat procedure as for primary route 5 To exchange primary and secondary route press icon with Good ONG SN A 1 2 indicated 6 Observe that correct warnings is activated as appropriate 7 Click alarm icon for display of alarms and warnings on route 8 Test that activating track steering is successful TECDIS 1 9 Radar overlay Check that radar overlay from radar is displayed on display after Good ONG ON A If present pressing radar overlay icon TECDIS 2 Good ONG ON A Verify that TECDIS handle different functions like 1 Disconnect position sensors and observe dead reckoning performance verify that alarm is given pos sensor 1 2 lost 2 Activate track dialog and set past tracks visible by clicking on show icon B Enter manual fix by activating bearing icon Click on center button on mouse when mouse is in position of visual object Use observed gyro bearing to m
3. power Autopilot TCS function Rudder angle is frozen at connection to this time autopilot while turning This test is dangerous 12 Simulate failure in Not influential Switches No 1 gyro automatically from No 1 to No 2 13 Check that second gyro Not influential is automatic applied in case of failure in the active gyro Checklists prior to completion of TECDIS TCS and TECDIS AW installation completed Page 88 TECDIS Installation Manual Vessel Name ID Date of installation Name of technician Checklist performed Sign The checklists in section 6 2 shall be filled in and signed for all TECDIS installations where Track Control functionality is present TECDIS TCS TECDIS AW in order to verify proper installation of the ECDIS system onboard 6 3 Additional checklist prior to completion of TECDIS AW installation 1 Conning Verify that when one of the ECDIS processors lose sensor data on one serial line display of sensor data relevant according to failed serial line on conning monitor is not affected ei Verify that installation is done according to block diagram for TECDIS AW system Verify that installation is done according to functional description given for TECDIS AW system Verify that required conning info according to pee ath AW requirements is displayed correctly T Verify that requirements set forth in section 1 7 are fulfilled Additional c
4. Requirement Results Harbor Acceptance Test 15 minutes TECDIS 1 Go to setup menu and verify NMEA inputs are valid Check Good ONG ON A 1 External data se input values for position and course TECDIS 2 Good ONG ON A Verify that TECDIS receives valid sensor data from a minimum TECDIS 1 of Mo Good ONG ON A 2 External data e Two independent positioning sensors e Two independent heading sensors TECDIS 2 e A speed sensor Good ONG 0N A TECDIS 1 l Good ONG ON A 3 Alarm system Werify that TECDIS is connected to a separate alarm system TECDIS 2 Good ONG ON A TECDIS 1 ne Good SONG N A 4 System status Check that no alarms warnings are pending in alarm window TECDIS 2 Good ONG ON A 1 Select setup menu chart utilities chart licenses TECDIS 1 2 Verify that licenses are valid for intended voyage Good ONG ON A 5 Chart database Click C Map chart update 4 Verify that charts are updated in update log TECDIS 2 Good ONG ON A Sea Trial Test 15 minutes 1 Activate ARPA d d select at t EPA Activate on radar and select a target a o es P Click the symbol button of ARPA Targets Good ONG ON A If esei 3 Click the symbol button of AIS Targets TECDIS 2 4 AIS and ARPA Targets are displayed on the top of charts Good ONG ON A TECDIS 1 Bae oa Correct indication is shown at the each configured window on Good ONG oN A 7 Eo the Conning Display Verify that selected sensors used by p heading position is correctly indicated TECDIS
5. TECDIS Installation Manual Page 79 Chapter 6 Checklists regarding installation 6 1 Checklist prior to completion of TECDIS installation Task to be performed Verify that all selected ports are receiving transmitting data and that ports have been given names on both main and back up TECDIS Names shall be according to the data they are receiving transmitting 2 Verify that sensor data is correctly distributed between main and back up TECDIS NMEA server program gt postion on both main and tacenpTecDIS o position on both main and back up TECDIS espmentaccometedspmpe DES nne equipment are connected to a proper UPS Verify that boat size are correct compared to chart on S both main and back up TECDIS TECDIS TECDIS is working properly Check that TECDIS transmits alarm to external systems If installed verify generation of conning picture and correct display of sensor data on conning monitor check against engine telegraph speed repeaters gyro repeaters etc 0 Verify audible signal from alarm speaker on TECDIS Verify sensor data correct size of vessel etc is filled in on main and back up TECDIS Verify that back up of default setup values have been g performed save setup default values on main and back up TECDIS Verify that installed charts have been correctly installed on both main and backup TECDIS if installed and that charts license matches Unplug TECDIS USB key restart
6. TECDIS to verify it starts up in normal mode chart program starts automatically and boat symbol and sensor data are displayed If connected to internet verify that a switch is available to disconnect TECDIS from internet when the connection is not in use Fill in hardware software fact sheet and file it in ships documents in technician personal files and send a copy to Furuno Norway or Telko AS W P Nn nN Page 80 TECDIS Installation Manual Model type a a E 18 Keyboard Back up Back up cx Processor Maln oa a pe TT Ca rane OOO O o wee OO o reene O r raeson O s moo O 25 mono O a comingmonior SSS 2s comings morior SSS 29 hmo OO o momet OOOO o won S S o o O a meos O s mose O e avromor E S En a Vessel Name ID Date of installation Name of technician and company Checklist performed Sign This checklist shall be filled in and signed for all TECDIS installations in order to verify proper installation of the ECDIS system onboard TECDIS Installation Manual Page 81 6 2 Checklist prior to completion of TECDIS TCS and TECDIS AW installation If installation includes Track Control functionality the following tests must be performed TECDIS 1 and 2 No Function
7. ake a red line in chart towards estimated position Repeat procedure to make two lines resulting in a cross bearing TECDIS 1 4 Update charts enter chart utilities menu choose C Map i Aids to charts update Use semi auto update Create a update Good ONG N A navigation request file on memory stick TECDIS 2 Send file to updates c map no and load received file into Good ONG ON A TECDIS Update loaded successfully shall be presented when update Is completed 5 Activate a route in route menu To alter at route underway click on Edit icon in route menu Modify route and click on OK icon Route is now altered When at track steering mode 3 waypoints are not allowed to alter last waypoint next waypoint and waypoint after next 6 Manual adjustment for position is available in setup menu click on nav position offset icon and a dialog box appear in top right corner of map Enter offset values as appropriate TECDIS Installation Manual Page 83 Autopilot type tick one box only Ansch tz NP 2025 PLUS Adaptive Autopilot Furuno FAP 2000 Autopilot EMRI SEM 200 Autopilot Function Requirement Results Harbor Acceptance Test 15 minutes Correct number is shown at each box of below Heading Speed 1 HEADING CONTROL is activated when steering mode switch is set to auto Present heading is displayed in heading display and in preset heading
8. be settled after calculations from yard Page 86 TECDIS Installation Manual ECDIS Scheduled Track Course 90 deg AP Scheduled Course 90 deg Wheel Over Point WP Approach alarm 30 sec before wop Pre Warning alarm d I 120sec before wop 1 Trial Speed NSRP ee Ship start turn from wheel over point with 90 deg Angle TCS Test 2 Failure point at straight leg Turn radius is with 1 0NM TCS Test3 Failure point in turn TECDIS Installation Manual Page 87 Fail to Safe Properties Item Fail Track Control TCS Test Result 1 Position sensor antennas When either of position sensor Remove No 1 to be blinded off acquisition stops TCS emits alarm but position sensor continues to function utilizing acquired antenna position from other position sensor LOG and GYRO When both position Remove No 2 sensor acquisition stops TCS emits position sensor alarm but begins navigation utilizing antenna estimated position made available by LOG and GYRO Then it after 10min automatically switches to Radius mode and manual maneuver will be in effect 2 Disconnect position Same as above Remove No 1 2 sensor on a straight leg position sensor 3 Disconnect position Alarm will be emitted only from ECDIS Remove No 1 sensor during max radius which places no influence on TCS position sensor turn function output connector during maximum radius turn 4 Turn Heading Control Not available Adjustment of
9. display Present heading is activated as set heading 2 Verify parameter settings for rudder yawing counter rudder rudder limit ROT limit and radius value Verify mode Heading Control of heading change radius or R O T mode by observing key lamp 3 Alter set course by either turn knob and push set button to acknowledge or push and turn knob Observe correct rudder response 4 Observe rudder movement 5 Observe that max rudder limit is not exceeded 1 Rudder moves to 10 degrees PORT when SET HEADING is Steering Control set by 20 degrees below Gyro heading 2 Confirm the actual rudder angle by rudder angle indicator 1 Change operating mode from hand to heading control at Track Control TECDIS verify that correct mode is indicated on TECDIS and conning monitor also Shift from heading control to manual mode by switching steering mode selector Verify that change to manual mode is possible from all modes with a single operator action Change set course 50 deg to starboard off heading alarm not to be activated during setting of new course Alarm is de activated for a time period that is a function of present course and new desired course External data Good ONG Function Function Test override tiller in modes hand heading control and track Function Contro
10. eck that icon 1 is activated primary route Use boathook to select route from previous test item Click yes when asked to activate route Check that route monitoring parameters are shown in right menu XTE next waypoint info etc 1 Check that ship follows the test route selected on ECDIS Recommend test speed is normal sea speed 2 Check performance according item 1 with speed reduction applied in one turn 3 Check performance according item 1 with inducing current effect by using bow thruster during turn 1 Set WP pre warning and WP approach time on the ECDIS as per drawing below Verify that WP approach Alarm is generated when the ship approaches the WP 2 Verify that separate Alarm system activates back up navigator alarm when WP pre warning and WP alarm on ECDIS is not acknowledged 3 Set alarm for gyro mismatch to minimum in TECDIS Setup program Wait for alarm to be raised 4 Activate route and use Heading Control mode on autopilot Steer outside channel limit to generate XTE alarm 5 Set Heading off alarm low and use bow thruster to provoke a heading drift Verify that alarm is raised TECDIS Installation Manual Page 85 Example of route for Track Control testing stil it N f t A rte WPT 3 135 deg turn port WPT 5 135 deg turn starboard both with minimum radius WPT 4 60 deg turn port WPT 7 60 deg turn starboard both with 2 NM radius Minimum radius to
11. hecklist prior to completion of TECDIS AW installation completed Vessel Name ID Date of installation Name of technician Checklist performed Sign The checklist in section 6 3 shall be filled in and signed for all TECDIS AW installations in order to verify proper installation of the ECDIS system onboard
12. l Autopilot to go to hand Sea trial test 240 minutes Response and stability of Heading Control steering 1 Observed overshooting should max 2 deg on 10 deg course change and max 5 deg on 60 deg course change 2 Repeat another side course change with same value Heading Control Starboard 10 deg turn with NAV FULL speed lf available Port 10 deg turn with NAV FULL speed If available Starboard 60 deg turn with NAV FULL speed Port 60 deg turn with NAV FULL speed Tests to be repeated with half speed ahead Testing of interference of radio transmissions while in heading control observe system while 1 Transmitting a call with FS 2570 2 Transmitting a call with VHF s 3 Transmitting a message with Felcom 15 1 amp 2 4 Transmitting a call with Felcom 70 Track Control Steering function test should be performed as follow in the next Steering lists Track Control Test and Fail to Safe Properties Page 84 TECDIS Installation Manual No Route monitoring Track keeping Track Control System Test Items to be checked during sea trial The following units have to be tested prior to the Track Control test ECDIS AUTOPILOT STEERING GEAR Create a test route for Track Control in keeping with the vessel maneuverability as per shown example attached or import by file Enter route menu ch
Download Pdf Manuals
Related Search