Home
inst.sheet 4p b.charger s3/s4 - STAR
Contents
1. Information This manual contains operating instructions and important safety The MTC400 Lithium lon Quad Charger is designed to charge up to four Li lon battery packs simultaneously The contents of this manual are subject to change without prior notice Safety Guidelines e Use only the power cord supplied in the package Do not insert foreign objects into the charger e Keep the charger in a cool dry place away from direct sunlight high te mperature and moisture e Do not operate the charger if it appears damaged e Do not disassemble incinerate or short circuit batteries the charger or related components e Do not operate the charger when your hands or body are wet e Do not operate the charger near water e To reduce the risk of burn unplug the charger before cleaning e This charger cannot be used for any other types of batteries e Never attempt to disassemble or alter any part of this product Contact your dealer for assistance SEAI 4 Unit Battery Charger S300 S400 MTC400 User s Manual Suitable Environment for the Use of Quad Charger is as Follows 1 Operation Temperature 0 C to 40 C No Condensation 2 Storage Temperature 30 C to 85 C 3 Relative Humidity 5 to 95 No Condensation 4 Altitude 0 10 000 feet 5 Cooling Convectional Non Vented Case STAR MICRONICS CoO LTD 6 Applicable Battery Pack A800 001 Battery Pack S3 S4 536 Nanatsushinya Shim
2. and then remove it 3 Trouble Shooting Federal Communications Commission Radio Frequency Interference Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation v If the power lamp V is turned off e Check if the adaptor is properly connected or not NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures v If LED is blinking when the battery is being charged e Check if the battery pack is properly installed or not v LED Status on Quad Charger Battery Charger e f a ba
3. izu ku Shizuoka 424 0066 Japan Tel int 81 54 347 0112 Fax int 81 54 347 0409 1 Setting Up the Quad Charger 2 Using the Quad Charger E Checking the Components E Connecting the Power Cable lt User s Manual Adapter Power Cord lt The above items are standard accessories If an item is missing from the box contact your dealer gt E Part Name 1 Connect the AC cord to the adaptor and connect the adaptor to power jack of the Quad 2 Plug the AC cord into the electrical outlet with an input power of 100 240VAC 50 60Hz 1 7A When the AC cord is plugged in Membrane the Red LED on the power lamp V is illuminated up Power Lamp RED Charging Lamp E Charging the Battery Pack E LED Indicator Battery Status V Installing the Battery CHARGING FULL z6 ERROR CHARGED Charging Lamp 1 Amber Red Green 2SEC ON and OFF POWER ON 2 LED OFF Battery Unloaded 3 Red LED ON Charging 4 Green LED ON Fully Charged Trickle Charge 1 Insert the battery pack into the charging bay as shown above 5 Red LED Flashing Error 2 Push the battery until it snaps into place Soe Trouble Shooting on F aga 5 3 If the battery is properly installed the Quad will charge it The 4 charging lamps report status For reference it takes approximately 90 to 120 minutes for the battery to fully charge 4 To extract the battery from the Quad pull up on the side latch
4. ttery has been fully charged in the Quad and is then installed into a printer with its AC adaptor plugged in the charging lamp will remain off indicating a full charge e Likewise if a battery has been fully charged in a printer and then transferred to the Quad Charger the charging lamp will remain off indicating a full charge Consider these points if you see no illumination e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Ifyou have additional questions contact your dealer This statement will be applied only for the printers marketed in U S A FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment For compliance with the Federal Noise Interference Standard this equipment requires a shielded cable For RF interference suppression if a ferrite core is provided with this device affix it to the interface cable Copyright 2010 2011 Star Micronics Co Ltd im00131EN
Download Pdf Manuals
Related Search
Related Contents
SBX_Programming_Guid.. - Forward Telecommunications Services Boss Audio Systems 738UA car media receiver Copyright © All rights reserved.
Failed to retrieve file