User Manual - actlaser.com.tw
Contents
1. Out from the first unit to In on the second Out from the second to In on the third and so on Auto mode E To set the master Set DIP switch pin 10 and 11 to ON other pins to OFF E To set the slaves Set pin 1 to ON other pins to OFF Sound Active mode E To set the master Set DIP switch pin 11 to ON other pins to OFF E To set the slaves Set pin 1 to ON other pins to OFF 3 DMX Operation DMX operation gives the users freedom to create their own programs tailored to their own individual needs To run this unit in DMX mode connect the unit to any standard DMX controller via XLR connectors Please consult DMX controller manual to determine address Function Selection Chart akes jasle lz 8 9 10 11 12 SETSOUND AUTOMODE SET SOUND AUTO MODE MASTER ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF N A SLAVE SET ADDRESS OFF OFF N A DMX MODE Twister AL46 Series User Manual Your Best M gtr nooner 2007 ACTOR MATE CO LTD in Laser Lighting No 15 Lane 83 Lungshou Street Taoyuan City Taiwan 330 R O C Tel 886 3 3791326 Fax 886 3 3791919 www actlaser com tw active actlaser com tw ACTOR MATE2. adjustment a If problems cannot be solved please contact your dealer for service Cleaning Use a soft cloth and normal glass cleaner to clean the outside casing and the hexagonal reflection mirror Cleaning frequency depends on the environment in which the fixture operates Be sure to dry all parts before plugging the unit back in Specifications Model No AL46 05R 30R 50R 100R AL46 05G 20G 30G 4 9 30 50 100mW x 2 4 9 20 30mW Lasercolor Red Green Model No AL46 5R5G AL46 50R20G AL46 100R30G AL46 200R50G Laser Power 4 9 200mW Red amp 4 9 50mW Green Size mm L435 x W220 x H135 Fuse Operating Modes 1 Stand Alone Operation Auto Sound Active Mode Auto mode m The unit runs built in program to change the laser effects automatically Set DIP switch pin 10 to ON other pins to OFF to run Auto mode Sound Active mode S This unit has built in program that will react to sound and music under Sound Active mode Set all DIP switch pins to OFF to run Sound Active mode Please adjust Sensitivity Adjustment Knob to fine tune the optimum level of sound reaction 2 Master Slave Operation Auto Sound Active Mode This mode allows user to link up to 32 units to run the Master Slave operation In the Master Slave operation one unit will act as the controlling unit and the others will react to the controlling unit Daisy chain your units via the standard XLR microphone cables in the following configuration
3. Introduction Safety Label Position Thank you for selecting Twister Twister is a four channel DMX laser which can be Front Panel Bottom Panel controlled via a standard DMX controller It is a lightweight mini intelligent fixture and is an ideal product for discos small clubs exhibitions and any place that need Laser aperture amp aperture label Certification identification and warning label visionary effect Twister creates exciting dual beam show with double scanner action and four operating modes For safe operation read this manual before powering or installing the fixture follow the safety precautions listed below and observe all warnings printed in this manual and on the fixture Safety Precautions a E Do not spill liquids in to or on to your unit If this ever happens disconnect the main power immediately Do not connect this unit to any dimmer pack E Always disconnect from main power before making any type of connection E Be sure to locate this unit in a place with adequate ventilation at least 15 cm from a Left and Right Side Panel wall and mount this unit in safe and stable matter E To prevent fire or shock hazard do not expose this unit to a high temperature or high humidity area Please unplug unit when not in use E Always keep combustible materials away from the fixture Hm This unit is intended for indoor use Use of this unit outdoors voids all warranties E Always refer service to a qualified technician Never loo
4. k directly into laser beam E Occasional breaks are necessary to prevent breakdowns Top Panel E Caution Use of controls or adjustments or performance of procedures other than as specified herein may result in hazardous radiation exposure Warning label Control Panel Introduction Set Up Unpacking Twister comes with 1 hanging bracket 2 clamp levers 2 washers 1 power cord and 1 user manual Unpack carefully and be sure that no damage has occurred during shipping If there is anything missing or appear to be damaged please contact your dealer Power Connection Be sure the source voltage in your area matches the required voltage for your Twister before plugging your unit in Incorrect voltage selection will detrimentally affect the operation of this product DMX Cable Connection Twister is a four channel DMX fixture that can be operated with universal DMX controller This unit and DMX controller require a Power Cord Connection standard 3 pin XLR connector for data input and data output Fuse Installation Mounting Twister should be properly mounted by using a suitable Power Switch hanging clamp and safety cable Use in a well ventilated area Be sure no Sensitivity Adjustment Knob ventilation slots are blocked Microphone DMX In amp Out DIP Switch Pin Operating Modes Cont Operating Modes Cont DMX Signal Levels DMX Signal Levels Channel 1 Channel 2 Channel 3 Channel 4 Range Lines Selection Ra
5. nge Mirror Rotation No 1 Mirror Rotation No 2 Lines change every 5 928 255 Sound Active 928 255 Sound Active seconds 224 227 lt D 224 227 gt Counterclockwise Fast Clockwise 220 223 D 220 223 Z gt Counterclockwise Medium Clockwise Pattern 15 26 219 D 26 219 gt Counterclockwise Slow Clockwise 185 198 Pattern 14 Patterns Selection Automatically change all the 226 2 6 255 patterns in every 10 seconds 221 255 Lines change every 3 seconds 157 207 Dotted Line 3 199 203 208 225 204 220 Sound Active Mode 105 156 Dotted Line 2 53 104 Dotted Line 1 i 213 215 209 212 209 212 Clockwise Counterclockwise Slow 205 208 205 208 lt D Clockwise Medium Counterclockwise Medium 201 204 gt 291 204 gt Clockwise Counterclockwise Fast 213 215 Pattern 3 17 30 Pattern 2 200 200 0 Off 4 16 Pattern 1 0 360 0 3 Off 0 360 0 Fuse Replacement Always disconnect from main power supply before attempting to replace the fuse Remove the old fuse from the holder and replace with the exact same type fuse Replacement with anything other than the specified part may damage your unit Trouble Shooting If there is no light from the unit please check the main power supply and fuse a If unit does not respond to DMX please check the DMX cables are connected properly and are wired correctly a If unit does not response to the music please check the sound activation
Download Pdf Manuals
Related Search