Home

Air Hose Alert System Manual

1. Driveway Alert Systems Rev 09 12 2014 Page 9 of 9 Copyright 2014 Miltronics Manufacturing Inc
2. The Battery in the Sensor Transmitter is not a new high quality alkaline battery The Battery in the Sensor Transmitter is depleted below the voltage required to sense activity The Sensor Transmitter is not securely mounted and is shaking or moving slightly The sun is shining directly into the Sensor Transmitter Lens The sun is reflecting off large reflective objects into the Sensor Transmitter Lens Objects free to move in the wind bushes small trees etc are in the sensor s detection zone PROBLEM My Receiver is constantly activated CORRECT THE ADVERSE CONDITIONS THAT EXIST The Battery in the Sensor Transmitter is not a new high quality alkaline battery The Battery in the Sensor Transmitter is depleted below the voltage required to sense activity There is interference in the area and the system coding needs to be changed Still have problems or questions Call Technical Support 603 355 6677 Driveway Alert Systems Rev 09 12 2014 Page 8 of 9 Copyright 2014 Miltronics Manufacturing Inc Made Better In The USA by Phone 603 352 3333 Miltronics Manufacturing Inc Ais Sales 800 828 9089 95 Krif Road f t Fax 603 352 4444 Keene NH 03431 QEroncs www drivewayalert com www miltronics com info drivewayalert com CAUTION Changes or modifications not expressly approved by Miltronics could void the user s warranty and authority to operate this device FCC STATEMENT This device complies with part 15 of
3. Inc Made Better In The USA by Phone 603 352 3333 Miltronics Manufacturing Inc AAs Sales 800 828 9089 95 Krif Road f t Fax 603 352 4444 Keene NH 03431 QTEronces www drivewayalert com www miltronics com info drivewayalert com Driveway Alert Systems Troubleshooting Guide When your system is operating properly there are three main functions being performed First the Pressure Sensor in the Transmitter detects activity Second once activity is detected the Transmitter sends a signal to the Receiver Third the Receiver gets the transmitted signal from the Sensor Transmitter and activates the Alert Tone and the Event Diode at the Receiver If your system is not working as expected review this troubleshooting guide and keep in mind there are three different functions to consider As you troubleshoot and alleviate various adverse conditions it is best to have someone help you perform the Walk Tests It is important to consider that household appliances induce noise into the household electrical lines and outlets In order to maximize the range between the Receiver and Transmitter our Receivers are highly tuned and very sensitive When possible isolate the Receiver on its own circuit or a circuit that has minimal use by other devices LED Lighting and LED TVs induce a tremendous amount of electrical noise into household circuits Computers and motors also create a high level of electrical noise Other wireless electronic devices s
4. the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for an intentional radiator pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Miltron l Miltronics Manufacturing Inc 95 Krif Road Keene NH 03431 USA Sales 800 828 9089 Offices 603 352 3333 Fax 603 352 4444 info miltronics com
5. EWAY ALERT SYSTEMS FAMILY The Only Original Driveway Alert Systems Home and Yard Alert Multi Channel Systems Campers Alert and Hunters Alert Portable Receivers Air Hose Alert Old Gas Station Style Pressure Tube Sensor Transmitter Magnetic Switch Transmitter for Windows Doorways and more Trip Wire Transmitter for Perimeters or Large Valuable Items High Water and Low Water Sensor Transmitters Push Button Transmitters Relay Transmitters ISA Alert Systems for those in need Mail Delivery Sensor Transmitters Thermal Alert Systems Hard Wired Systems DRIVEWAY ALERT SYSTEMS AVAILABLE ACCESSORIES Sound and Light Siren Chime Buzzers Fire Bell and Strobe Light More Event Counter Relay Module Relay Outlets Cables and Power Options LIMITED LIFETIME WARRANTY Miltronics Manufacturing Inc provides a lifetime warranty on parts and two years on labor Miltronics guarantees all parts of this product to the original owner against manufacturing or parts defects This warranty shall not apply to defects resulting from improper installation or use unauthorized repair and consequent damage abuse modification using in a fashion other than intended fire flood or act of God or on which serial numbers have been altered defaced or removed If your unit cannot be repaired Miltronics may replace it with new or reconditioned merchandise Miltronics will assume no liability for commercial loss or any kind of damage resul
6. Made Better In The USA by Phone 603 352 3333 Miltronics Manufacturing Inc Ais Sales 800 828 9089 95 Krif Road f t Fax 603 352 4444 Keene NH 03431 j FONICS www drivewayalert com www miltronics com info drivewayalert com Driveway Alert Systems Air Hose Alert System Old Gas Station Style CH A oa CS CED USER MANUAL READ THIS ENTIRE MANUAL PRIOR TO INSTALLATION AND OPERATION We thank you for purchasing this Driveway Alert System All our Driveway Alert Systems are proudly manufactured in the USA under strict quality control standards using the best available materials We hope you will be pleased with its performance all weather construction Questions Problems Call Technical Support 603 355 6677 All our Driveway Alert Systems Components and Accessories are compatible We offer a wide variety of Sensor Transmitters and Receivers that can be used in conjunction with all our Driveway Alert Systems Don t be surprised Use Driveway Alert Monitor your home yard barn garage business and much more with Driveway Alert Systems Driveway Alert Systems Rev 09 12 2014 Page 1 of 9 Copyright 2014 Miltronics Manufacturing Inc Made Better In The USA by Phone 603 352 3333 Miltronics Manufacturing Inc Ail Sales 800 828 9089 95 Krif Road f t Fax 603 352 4444 Keene NH 03431 QTronIcs www drivewayalert com www miltronics com info drivewayalert com DRIV
7. below Antenna FCC Label on back Cover Screws Coding DIP Switch Only change DIP Switch settings if experiencing interference DRIVEWAY ALERT Systems Air Hose Alert Transmitter www drivewayalert com Matronics Mig inc 95 Krif Rd Keene NH ON 1 2 S Q 5 lauuuo Five Position Transmitter Coding DIP Switch Pressure Sensor Switch AIR HOSE ALERT Pressure Switch Sensor Transmitter Driveway Alert Systems Rev 09 12 2014 Page 4 of 9 Copyright 2014 Miltronics Manufacturing Inc Made Better In The USA by Miltronics Manufacturing Inc Ail 95 Krif Road A A f t Keene NH 03431 wren ICS www miltronics com RECEIVER OPERATION AND INSTALLATION Phone 603 352 3333 Sales 800 828 9089 Fax 603 352 4444 www drivewayalert com info drivewayalert com Plug the transformer into a 110 volt indoor outlet Stand the Receiver up or mount it to the wall with the included hook and loop fasteners Extend the wire antenna straight upward Deluxe Extended Long Range Model attach the rigid bayonet mount antenna to the connector on the Receiver The Receiver will sound the alert and the Event Diode will illuminate when the sensor is activated and the signal is received The alert sound resets itself after five seconds and the Event Diode remains on Pressing the Reset Button after an event will shut off the Event Diode The Alert Tone will continue to alert you with ever
8. er operating appliances Hard wired Sensor Transmitters and Receivers are available when transmission is not possible or practical RECEIVER CODING ADJUSTMENT The system coding is factory pre set and should be adjusted only in the event of interference from another source Prior to adjustment unplug the 110 volt transformer from the power outlet and disconnect power cord from the Receiver Remove the volume control knob and cover to access the Five Position Coding DIP Switch See diagram on page 6 The DIP Switch settings in the Receiver must match the settings in the Sensor Transmitter Replace cover and volume knob prior to operation WALK TEST After setting up your system perform a Walk Test to ensure proper system operation Walk and drive through the detection area and have someone listen for the receiver to sound The Sensor Transmitter and or the Receiver can then easily be repositioned if not performing as desired See the FCC Statement at the end of this Manual for more information Driveway Alert Systems Rev 09 12 2014 Copyright 2014 Miltronics Manufacturing Inc Page 5 of 9 Made Better In The USA by Miltronics Manufacturing Inc 95 Krif Road f t Keene NH 03431 YEr ones www miltronics com DRIVEWAY ALERT Deluxe Long Range Receiver Wire Antenna Volume Control lt ei oe eae Deluxe LR and Deluxe ELR Models only Models only DELUXE CA DRIVEWAY ALERT 00998 LONG RANGE T A J Even
9. itch Sensor Transmitter Driveway Alert Systems Rev 09 12 2014 Page 3 of 9 Copyright 2014 Miltronics Manufacturing Inc Made Better In The USA by Phone 603 352 3333 Miltronics Manufacturing Inc Ais Sales 800 828 9089 95 Krif Road f t Fax 603 352 4444 Keene NH 03431 QTETronics www drivewayalert com www miltronics com info drivewayalert com Mount the weatherproof sensor approximately 2 to 3 feet above the ground to a tree wooden post or side of a building DO NOT PLACE SENSOR TRANSMITTER ON THE GROUND Straighten the wire antenna and extend upwards Extend the Rubber Hose across the pathway or roadway to be monitored Refer to the System Set Up on page 7 Perform the Walk Test see page 5 prior to mounting permanently Once your system is operating properly permanently mount the Air Hose Alert Sensor Transmitter using the supplied mounting screws PLEASE NOTE A shorter transmission range may occur when the outside temperature falls below 20 degrees F due to a natural drop in battery voltage The Sensor Transmitters are completely weatherproof and will operate to 40 degrees Fahrenheit TRANSMITTER CODING ADJUSTMENT The system coding is factory pre set and should be adjusted only in the event of interference from another source Remove the battery cover to access the Five Position Coding DIP Switch The DIP Switch settings in the Sensor Transmitter must match the settings in the Receiver See diagram
10. nd a 9 Volt Battery PRESSURE SWITCH SENSOR TRANSMITTER OPERATION AND INSTALLATION First remove the four cover screws and install a high quality 9 volt alkaline battery in the space located at the bottom of the Transmitter case Replace the cover and install the cover screws The Battery will last about six months under normal use The pressure sensor is positioned at the bottom of the Sensor Transmitter case inside the black pressure switch Next attach the open end of the 25 foot rubber pressure hose to the pressure switch Slip the rubber tube over the pressure switch nipple and secure with the circular clamp See diagram below The pressure switch will activate when a vehicle drives over the pressure tube When the battery s voltage has dropped below the Sensor Transmitter s required operating voltage transmissions are sent to the Receiver until the battery voltage becomes too low to transmit Antenna Straighten and extend upward Mounting Holes Mount vertically to side of building post or tree DRIVEWAY ALERT Systems Cover Screws Remove to access Battery Compartment and System Coding DIP Switch Air Hose Alert Transmitter Battery Compartment Install high quality 9 Volt alkaline battery Replace cover and screws www drivewayalert com Miltromics Mig inc 95 Kril Rd Keene WH Pressure Sensor Switch Attach Rubber Pressure Tube and tighten circular clamp AIR HOSE ALERT Pressure Sw
11. t Diode RESET lt Reset Button MILTRONICS Phone 603 352 3333 Sales 800 828 9089 Fax 603 352 4444 www drivewayalert com info drivewayalert com Accessory Connector Deluxe LR and Deluxe ELR Models only Power Connector Five Position Receiver Coding DIP Switch Vv 5 SEC E Jumper STAY on 10 SEC E J2 E Receiver Alert Timer Duration Jumper Settings Deluxe LR and Deluxe ELR Receivers only Driveway Alert Systems Rev 09 12 2014 Copyright 2014 Miltronics Manufacturing Inc Page 6 of 9 Made Better In The USA by Phone 603 352 3333 Miltronics Manufacturing Inc Ai Sales 800 828 9089 95 Krif Road f t Fax 603 352 4444 Keene NH 03431 FrOnIcs www drivewayalert com www miltronics com info drivewayalert com Place your Receiver in a convenient Optional Additional Receivers and location in your home Read the other Driveway Alert Sensor operating instructions and the FCC Transmitters can be added to enhance statement for locating suggestions your Air Hose Alert System t y Mount the Transmitter to the side of a Maximum distance building or to a post or tree about 2 to between Transmitter 3 feet above ground Extend Rubber and Receiver is up to Hose across pathway or roadway to 1 000 feet be monitored Air Hose Alert System Set Up Driveway Alert Systems Rev 09 12 2014 Page 7 of 9 Copyright 2014 Miltronics Manufacturing
12. ting from malfunction of the product or resulting from its unsuitable use In any event liability shall not exceed the original purchase price WARRANTY REPAIR POLICY The entire system requiring warranty repair must be returned to Miltronics by prepaid freight with proof of purchase a brief description of the problem your email address and a daytime phone number to contact you if necessary Beginning with year three of this warranty a minimal labor fee will apply A handling fee will apply to products sent to Miltronics that are not covered under warranty CUSTOMER RETURN POLICY Return of unused product must be done within 30 days of purchase Shipping and handling charges are not refundable A 20 restock fee may apply MILTRONICS Manufacturing Inc 95 Krif Road Keene NH 03431 Sales amp Info 1 888 NH ALERT Technical Support 1 603 355 6677 Driveway Alert Systems Rev 09 12 2014 Page 2 of 9 Copyright 2014 Miltronics Manufacturing Inc Made Better In The USA by Phone 603 352 3333 Miltronics Manufacturing Inc Ais Sales 800 828 9089 95 Krif Road f t Fax 603 352 4444 Keene NH 03431 QTETronics www drivewayalert com www miltronics com info drivewayalert com AIR HOSE ALERT SYSTEM KIT CONTENTS Driveway Alert Receiver Receiver Power Cable with Transformer and Hook amp Loop Mounting Fasteners Air Hose Alert Pressure Switch Sensor Transmitter Rubber Tube 25 feet with Clamp Mounting Screws a
13. uch as garage door openers and Wi Fi networks can transmit wireless signals that interfere or create false alarms in your Driveway Alert System PROBLEM My Receiver will not activate when objects pass through the sensor detection zone CORRECT THE ADVERSE CONDITIONS THAT EXIST The Battery in the Sensor Transmitter is not a new high quality alkaline battery The Battery in the Sensor Transmitter is depleted below the voltage required to sense and transmit The Sensor Transmitter is not mounted two to three feet above the ground The Sensor Transmitter is out of range and the signal is too weak to be received The Sensor Transmitter is very close to the Receiver The transmitted signal does not have a clear path to the Receiver for maximum unobstructed reception The transmitted signal is not propagating through the dense trees for maximum unobstructed reception The transmitted signal is not propagating through dense earth rock or cement The Receiver is behind or shrouded by thick or dense walls The Receiver is plugged into an outlet with other devices or appliances The Receiver is plugged into the same circuit with other devices or appliances The Receiver is obstructed and not placed near a window for maximum unobstructed reception There is interference in the area and the system coding needs to be changed PROBLEM My Receiver activates when nothing passes through the sensor detection zone CORRECT THE ADVERSE CONDITIONS THAT EXIST
14. y intrusion The Alert Tone Duration is factory pre set for five seconds By changing the on board Jumper settings you can change the tone duration to 10 seconds or constant on Deluxe LR and Deluxe ELR Receivers only See diagram on page 6 When in the constant on mode the Alert Tone and Event Diode can be reset by pressing the Reset Button The volume control Deluxe LR and Deluxe ELR Receivers Only is used to change the sound level of the Alert Tone Driveway Alert Long Range Deluxe Driveway Alert Long Range Deluxe Driveway Alert Extended LR The Deluxe Long Range and Deluxe Extended Long Range Receiver Models come equipped with an accessory jack for the easy addition of accessories sold separately adding to the versatility of the Deluxe systems Carefully align and plug your Accessory plug into the jack on the Receiver and ensure you feel two clicks indicating proper engagement The accessory output supports 12 volt DC accessories with a maximum current draw of 300 mAmp In unobstructed space the reception range can reach up to 1 000 feet up to 2 500 feet for Extended Long Range models Range may be reduced by certain obstructions such as metal buildings dense woods brick walls etc For maximum range locate the receiver in an area in your home with some direct visibility to the sensor In order to minimize interference it may be necessary to plug the Driveway Alert Receiver into an electrical circuit with no oth

Air Hose Alert System Manual

Contents

Download Pdf Manuals

Related Search

Related Contents