Instruction Manual
Contents
1. Ader ATD 80351 SABER 15W CORDED UNDERHOOD LIGHT USER S MANUAL FEATURES e 30 Super Bright SMD LEDs e 18 2 SJTOW 25ft cord remains flexible in cold weather and water resistant e ABS handle with double injection impact protection and ergonomic design provides comfortable usage e Aluminum alloy hook with PVC cover for protection soft coated padded hooks help prevent scratching of the vehicles surface e The bar extends from 47 to 75 and easily attaches to most SUV s and trucks e 360 degree ratcheting hooks provide safe and firm attachment e CSA listed california Prop 65 WARNING This product contains chemicals including lead known to the State of California to cause cancer birth defects or other reproductive harm Wash hands after handling General Safety Warnings WARNING The instructions and warnings contained in this manual should be read and understood before using or operating this tool Do not allow anyone to use or operate this tool until they have read this manual and have developed a thorough understanding of how this tool works Failure to observe any of the following instructions could result in severe personal injury to tool user and bystanders or cause damage to the tool and property Keep this manual for future reference Note The warnings and cautions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the ope2. extension cords If used outdoors they must be marked For Outdoor Use Those cords having a 3 prong grounding type plugs and mating receptacles are to be used with grounded tools LN WARNING Use of improper size or gauge of extension cord may cause unsafe or inefficient operation of your tool or cause damage to your tool Be sure your extension cord is rated to allow sufficient current flow to the motor If in doubt always use a larger gauge cord Be sure to check the voltage requirements of the tool to your incoming power source NOTE The table below shows the correct size to use according to cord length and the amperage draw of the tool specified on the nameplate When in doubt use the next heavier gauge The smaller the gauge number the heavier the cord AWG American Wire Gauge Minimum Gauge for Extension Cords AWG when using 120 volts only Ampere Rating Total Length of Cord in Feet meters o 0 _ 6 B tt __ M Not Recommended ATD 80351 Specific Safety Instructions L WARNING Read all instructions before using WARNING For indoor use only do not use in or around tubs showers sinks pools hot tubs or in a wet environment Use only the recommended voltage and frequency requirements gt Do not move or turn off light by pulling the power cord Do not use if the cords or Clear tube are damaged Keep out of reach of children F a i i WARNING Do not o
3. 0351 10 RIGHT HANDLE SET 6 PRT80351 07 CLEAR TUBE LOWER __ _ PRT80351 12 BRIGHTNESS INDICATE BOARD Ce E 10 PRT80351 11 ON OFF SWITCH ______ DEAE Le 13 10 11 12 13 4 Visit us at www atdtools com Copyright C 2013 ATD Tools Inc All rights reserved
4. e to follow all warnings and instructions may result in electric shock fire and or serious injury or death LN WARNING Before connecting a tool to a power supply always check to ensure the power supply corresponds to the voltage on the nameplate of the tool A power supply with a voltage greater than that specified for the tool can result in serious injury to the user as well as damage to the tool Using a power supply with a voltage less than the nameplate rating is harmful to the motor If in doubt do not plug in the tool WARNING Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances This tool is equipped with a 3 prong plug and a 3 wire grounding system Never remove the grounding prong or modify the plug in any way Do not use any adapter plugs Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded NOTE Double insulated tools are equipped with a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still doesn t fit contact a qualified electrician to install a polarized outlet Do not change the plug in any way LN WARNING To reduce the risk of electric shock DO NOT use in damp conditions on wet surfaces or expose to rain Do not plug in this tool or operate it with wet hands or while standin
5. g in water WWARNING Never use the cord for carrying pulling or unplugging the power tool Grasp plug and pull to disconnect from outlet Keep cord away from heat oil sharp edges or moving parts Replace damaged cords immediately L gt WARNING Do not carry the power tool with your finger on the switch Ensure the switch is in the off position before plugging the tool into the power outlet In the event of a power failure while a tool is being used turn the switch off to prevent surprise starting when the power is restored WARNING Always remove the power cord from the electric outlet when making adjustments changing parts cleaning or working on the tool WARNING Care should be taken to arrange the cord so it will not be stepped on tripped over or otherwise subjected to damage or stress LN WARNING Never attempt to plug in or operate equipment with defective or damaged wires power cord or power cord plug Have any defective or damaged parts replaced immediately by qualified personnel L WARNING Avoid body contact with electrically grounded surfaces There is an increased risk of electric shock if your body is grounded f WARNING If the work area is not equipped with a permanently installed Ground Fault Circuit Interrupter outlet GFCI use a plug in GFCI between the power tool or extension cord and the power receptacle WARNING if an extension cord is necessary use only Listed
6. perate light with wet hands LN WARNING Keep lamp away from hot objects Operating Instructions e To use plug the unit into any 110 120 VAC power source such as a wall receptacle e Press the on off switch I to turn unit on press the other side of switch 0 to turn it off e With the unit plugged in and turned on the brightness adjust button will toggle your underhood light between the 7W and the 15W settings The 7W setting is indicated with 3 LED s lighting up while the 15W setting is indicated by all five LED s lighting up ON OFF Switch Brightness Adjust Button OFF 15W e The hooks can be adjusted by simply pulling out on them and affixing to whatever surface you like such as a car hood Up to 75 wide e Once your light is in place it can be rotated to the desired position by simply twisting the light You will hear ratcheting clicks as you rotate it HIBER ATD 80351 in 2 im fl E ji d ay Tl H a T IF j f 0 s T I ie i t3 dl L 09 14 ITEM ORDERING PART PART DESCRIPTION ITEM ORDERING PART PART DESCRIPTION PRT80355 01 PULL ROD ASSY PRT80351 09 BRIGHTNESS INDICATE COVER PRT80351 03 LEFT HANDLE SET PRT8
7. rator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator gt WARNING Use safety equipment Users and bystanders should use safety goggles or safety glasses with side shields which comply with current national standards or when needed a face shield Use an ANSI approved dust mask or respirator when working around metal wood and chemical dusts and mists This applies to all persons in the work area Also use non skid safety shoes hardhat gloves dust collection systems and hearing protection when appropriate gt WARNING Keep bystanders and children out of the work area while operating this tool gt WARNING Always keep your work area clean uncluttered and well lit Cluttered or dark areas invite accidents and injuries DO NOT work on floor surfaces that are slippery L gt WARNING Do not operate this tool if you are tired or under the influence of alcohol drugs or medications that could affect your ability to use the tool properly WARNING Dress properly Do not wear loose clothing or jewelery as they can be caught in moving parts Wear restrictive hair covering to contain long hair WARNING Do not reach over or across running machines Keep proper footing and balance at all times Non skid footwear is recommended when working Electrical Safety Warnings gt WARNING Read all safety warnings and instructions Failur
Download Pdf Manuals
Related Search