OmniView – User`s Guide (V1
Contents
1. Used clamps with screws for mounting the OmniClient to a panel Required Tool 2 Phillips Screw Driver Proper Torque Tighten the screws with a torque of 0 5 Nm Ensure the vertical and horizontal alignment of the system display box Table 2 Requirements for OmniView mounting into a subframe panel Mounting Position RS In order to ensure IP65 front sealing against dust and water mount the system ona non textured surface Before you install the OmniView system into a panel ora subframe for industrial cabinet verify the perfect condition of the seal at the rear of the front plate The seal has to be in place without surface imperfections defects and dirt www kontron com 8 Maintenance and Prevention Kontron systems reguire minimal maintenance and care to keep them operating correctly e Occasionally wipe the system with a soft dry cloth e Youshould only remove persistent dirt by use of a soft slightly damp cloth use only a mild detergent 8 1 Touch Screen Care and Cleaning z The front panel and the touch screen are covered by a plastic overlay and care should be taken when cleaning it Mild detergent and water is recommended for cleaning Use of strong solvents which could attack paint or plastic should be avoided The plastic overlay or the touch screen surface is subject to burning and scaring from direct heat sources such as cigarettes The display front is sealed against dust liquids etc2. 341 mm 13 467 14 94 62 62 24 l 24 Width 410mm 16 14 481 mm 18 94 544 mm 21 43 Depth total 66 5 mm 2 62 66 5 mm 2 62 66 5 mm 2 62 Depth from rear surface of 56 9 mm 2 24 56 9 mm 2 24 56 9 mm 2 24 display wim e 15 TE Front Panel Aluminum front plate with glass touch panel Housing Chemical coated Aluminum casting 9 3 Environmental Specifications Thermal Management passive cooling Operating Temperature 0 50 C Operating 20 to 90 non condensing Storage transit 5 to 90 non condensing up to 3 048 m 10 000 ft up to 4 622 m 15 000 ft 15 g 11 ms duration half sine 50 g 11 ms duration half sine Operating Vibration 10 500 Hz 1 0 g 3 axis Storage Transit Vibration 10 500 Hz 2 0 g 3 axis Protection class IP20 Front IP65 www kontron com 10 Regulatory and Certification Information 10 1 Product Regulatory Compliance 10 1 1 Product Safety Compliance The OmniView monitor complies with the following safety reguirements e UL60950 1 CSA 60950 1 USA Canada e EC60950 1 International CB Certificate amp Report including all international deviations e CE Low Voltage Directive 2006 95 EC Europe 10 1 2 Product EMC Compliance Class A Compliance The OmniView monitor has been tested and verified to copmply with following electromagnetic compatibility EMC regulations e FCC ICES 003 Emissions USA Canada
3. e CISPR 22 Emissions International e EN55022 Emissions Europe e EN55024 Immunity Europe e EN6100 3 2 Harmonics Europe e EN6100 3 3 Voltage Flicker Europe e CE EMC Directive 2004 108 EEC Europe 10 1 3 Certifications Registrations Declarations e ULListing US Canada e CE Declaration of Conformity Europe e FCC ICES 003 Class A Verification Report USA Canada www kontron com 11 Technical Appendix Interfaces The following tables contain the plug assignments for the external connections of the OmniView Low active signals are indicated by a minus sign 11 1 Power Connector DC Power Supply The external power supply is connected to the wall power out let by either the optional USA or EU AC power cable and uses a standard IEC 60320 C13 power cord See section 5 1 for details WARNING Do not attempt to modify or use an AC power cord set that is not the exact type reguired You must use a power cord set that meets the following criteria e Rating In the U S and Canada cords must be UL Underwriters Laboratories Inc Listed CSA Canadian Standards Organization Certified type SJT 18 3 AWG American Wire Gauge Outside of the U S and Canada cords must be flexible harmonized lt HAR gt or VDE Verbena Deutscher Electrotechniker German Institute of Electrical Engineers certified cord with 3x 0 75 mm conductors rated 250 VAC e Connector wall outlet end Cords must be termina
4. 75R www kontron com C2 ANALOG GREEN Analog output carrying the green color signal O 75R C3 ANALOG BLUE Analog output carrying the blue color signal O 75R c4 ANALOG HSYNC CRT horizontal synchronization output O C5 ANALOG GND Ground reference for RED GREEN and BLUE PWR C6 ANALOG GND Ground reference for RED GREEN and BLUE PWR www kontron com 11 4 DisplayPort Input Connector Conn CB102 W P 8470 2 2 1 80 TR Pin No Signal Description 1 ML L3N Main Link Ch 3 Differential Input negative 2 GND Ground 3 ML L3P Main Link Ch 3 Differential Input positive 4 ML L2N Main Link Ch 2 Differential Input negative 5 GND Ground 6 ML L2P Main Link Ch 2 Differential Input positive 7 ML LIN Main Link Ch 1 Differential Input negative 8 GND Ground 9 ML_LN1P Main Link Ch 1 Differential Input positive 10 ML_LNON Main Link Ch 0 Differential Input negative 11 GND Ground 12 ML_LNOP Main Link Ch 0 Differential Input positive 13 Config1 Config Pin1 connect to GND with 1M 14 Config2 Config Pin2 connect to GND with 1M 15 AUXP Auxiliary Ch Differential Input positive 16 GND Ground 17 AUXN Auxiliary Ch Differential Input negative 18 HPD Hot Plug Detect 19 POR Connected to Ground 20 PO Not Connected to internal circuits www kontron com 11 5 DP Connectors DPO DP1 The DP Display Port
5. The display is equipped with a Projected Capacitive touch screen The touch screen offers the same degree of user comfort as the mouse buttons The surface of the display is also mechanically protected through the touch screen The touch screen USB connected registers contacts of a finger and allows moving the mouse pointer This functions only under integration of the necessary software The corresponding touch screen driver for your operating system is installed on your OmniView monitor S Do not use a hard or a pointed object like screw drivers to operate the touch screen doing so may damage the touch screen surface The touch screen is covered with a glass panel and care should be taken when cleaning it see the section 8 1 Touch Screen Care and Cleaning 6 3 2 Front Plate The OmniView is suitable for installation in an instrument panel or other cabinet At the front side of the system an aluminum front plate bezel with integrated anti glare glass plate and capacitive touch is located For the outline dimensions of the touch monitor base refer to section 10 2 Mechanical Specifications 6 3 3 Calibrating the Touch Screen Unlike resistive touch displays the capacitive touch screen needs no further calibration after factory calibration Only special conductive styluses not included work with capacitive touch screens The capacitive touch screen is factory calibrated and needs no recalibration When using a styl
6. is based on standard DP type Foxconn 3VD51203 H7JJ 7H or Similar Figure 3 DP Connector front view Pin No Signal Description Type Note 1 Lane 0 p LVDS 2 GND PWR 3 Lane O n LVDS 4 Lane 1 p LVDS 5 GND PWR 6 Lane 1 n LVDS 7 Lane 2 p LVDS 8 GND PWR 9 Lane 2 n LVDS 10 Lane 3 p LVDS 11 GND PWR 12 Lane 3 n LVDS 13 Config1 Aux or DDC l selection 14 Config2 Not used O 15 Aux Ch p Aux Channel or AUX channel used by DP DDC Clk DDC Clk used by HDMI 16 GND PWR 17 Aux Ch n Aux Channel or AUX channel used by DP DDC Data DDC Data used by HDMI 18 Hot Plug l Internally pull down 100Kohm 19 Return PWR Same as GND 20 3 3V PWR Fused by 1 5A resetable PTC fuse common for DPO and DP1 11 6 Power Connectors The OmniView supports three power connector types Connector CN104 MOLEX 0039303045 WEL EEN EE EN a ees Connector J101 2 5mm DC Jack 12V 24V VDD max 5A ELE www kontron com 31 11 7 VGA Input Connector Connector CN101 15pin HD Sub female Pin No Signal Description 1 Red Red analog input 2 Green Green analog input 3 Blue Blue analog input 4 NC Not connected GND 5 GND red Ground 6 GND green Ground 7 GND blue Ground 8 GND Ground 9 VGA 5V 5V DC 10 GND Ground 11 NC Not connected
7. 12 SD Serial Data Line for DDC 13 HSYNC Horizontal Sync 14 VSYNC Vertical Sync 15 SCL Serial clock input for DDC www kontron com 12 Technical Support For technical support please contact our Technical Support department Tel 49 8341 803 333 e mail support kontron com Web http www kontron com support Make sure you have the following information on hand when you call e the unit part id number PN e the serial number SN of the unit the serial number can be found on the type label placed on the right side of the unit Be ready to explain the nature of your problem to the service technician If you have questions about Kontron or our products and services you can reach us by the above mentioned telephone number and on e mail address or at www kontron com 12 1 Returning Defective Merchandise Please follow these steps before you return any merchandise to Kontron 1 Download the corresponding form for returning a device with an RMA No Return of Material Authorization from our website www kontron com Support RMA Information You also can contact our Customer Service department to obtain an RMA No e Mail service kontron com 2 Ensure that you have received an RMA number from Kontron Customer Services before returning any device Write this number clearly on the outside of the package 3 Describe the fault that has occurred 4 Please provide the name and telephone number of a
8. de la class A est conforme a la norme NMB 003 du Canada 8 www kontron com 5 Scope of Delivery Please check that your package is complete and contains the items below according to the ordered unit configuration If you discover damaged or missing items please contact your dealer OmniView in the configuration ordered e OmniView 156 15 6 e OmniView 185 18 5 e OmniView 215 21 5 6x Mounting Clamp with Screws General Safety Instruction for IT Eguipment Power Supply 5 1 Optional Parts Included with your OmniView is the following optional accessory AC Power cable to be used in conjunction with the supplied Power Supply unit AC US AC EU www kontron com 5 2 Type Label and Product Identification The type label with the corresponding Kontron product part and serial number is located on the rear side of the display bezel Figure 1 depicts the type of label for a DC supply OmniView There are three primary model numbers of the OmniView based on the screen size The xxxx suffix in the model number identifies the ordered configuration System Type Model No Product ldentification OmniView 156 HMI OV156 xxxx 15 6 display OmniView OmniView 185 HMI OV185 xxxx 18 5 display OmniView OmniView 215 HMI OV215 xxxx 21 5 display OmniView Gkontron C Q MODEL NO HMI OV215 XXXX steal THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE Ol SERIAL N
9. person we can contact to obtain more information where necessary Where possible please enclose all the necessary customs documents and invoices 5 When returning a device e Pack it securely in its original box e Enclose a copy of the RMA form with the consignment www kontron com Corporate Offices Europe Middle East 8 Africa Oskar von Miller Str 1 85386 Eching Munich Germany Tel 49 0 8165 77 777 Fax 49 0 8165 77 219 info kontron com North America 14118 Stowe Drive Poway CA 92064 7147 USA Tel 1 888 294 4558 Fax 1 858 677 0898 info us kontron com Asia Pacific 17 Building Block 1 ABP 188 Southern West 4th Ring Beijing 100070 P R China Tel 86 10 63751188 Fax 86 10 83682438 info kontron cn www kontron com
10. 4 kontron uniron User s Guide Version 1 0 0096 22514 Table of Contents 1 Introduction messe MEE o RES u BEE se hide BEd ie e 3 1 Is Symbols used in this GULES sus Sy a siae Suen O E b o ees 4 2 Important Instructions ss i taadi eee eee eee eee es SES a ee 5 213 Note on the Warranty sv 80805 se n eds Gie ie n N Re ie N RE ig N ere Re ie ya n REDE ie Se Re ie ees 5 Bada Rl HS ron Of Accident Liability OBliGaE LON saesneg aeae Rn da 5 2 3 Liability Limitation Exemption from the Warranty Obligation 5 3 General Safety Instructions for IT Equipment iss ss ss ss ss ss seses 6 3 1 Electrostatic Discharge BSD dares RE Side e e poi a a ada we eS 7 Sele GESUNAIRG Methodg is EE ua SR EE p e wih Soci on in v 7 4 Electromagnetic Compatibility Class A Device 0 0 eee eee 8 4 1 Electromagnetic Compatibility EU ss ss sd is WEE srat ipid raies O I PRAVY e 8 A D ECC Statement USA sewe ss WEES ea RE See Ro a Re ai a ai 8 4 33 EMC Compliance Canada dead k U SS ese A O DE 8 b Scope of Delivery s a id SE A a A a R k 9 Bal Optional Parts s le vb slad b s RR rara b b Bow b oth eee aes 9 5 2 Type Label and Product Identification is es vee ss OA N RE e va 10 6 Product Description sses s nenene nenene rererere rererere rero 11 beba OmniView TOUGH Monitor Basie Mis a at o a LEN 12 6 2 Product Images OmniView 21 5 AC PSU other unit
11. O 3332450001 FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY LI LL ee S INTERFERENCE THAT MAY CAUSE UNDESIRED BATCH 0C00000003 sla This Class A digital device complies with Canadian MINNA z Cet apparell num rique de la classe A est conforme a 5 la norme NMB 003 du Canada Voltage Requirements MANUFACTURED NOVEMBER 2013 18 36 V 8A MAX KA ASSEMBLED IN U S A Figure 1 OmniView Label www kontron com 6 Product Description Before you begin using your OmniView you should take a few minutes to learn about the various connectors that are part of your OmniView The OmniView is a touch screen monitor designed for demanding industrial applications The OmniView is an integrated touch screen display The system is designed to be mounted in the user s application by either of the following methods Installation in an instrument panel or other cabinets preferred mounting method Installation by a heavy duty VESA 100 compliant mounting system All versions are suitable for installation in an instrument panel or other cabinet OmniView monitor must be mounted in an instrument panel or other cabinets using the corresponding supplied mounting clamps Installation using the VESA 100 mounting system must be properly designed to t support the complete load of the OmniView The OmniView is very flexible and can be customized to meet the requirements of
12. Power Connector DC Power Supply eee ec eee ss ss a 25 ll i DVI Input CONNECEOL ss AE Pa weed OE EE o OE EE ke 26 11 3 DVI Connector DVIS ses ea a r eects ee 2 11 4 DisplayPort Input Connector z ilea vd ban Va a BA ws 29 11 5 DE Connectors DPO DPL sb brand pol baw O OP eg 30 Vivo Power CONNEELOFS ye A Ske ol we ee wed wae a 31 11 7 VGA Iaput CONMECE OL ss sees sees tay Ee esa A N laced a lay Se ere Rew cel a Reg ie eee i a ee ele 32 12 Technical Support 33 12 1 Returning Defective Merchandise ss ss ss ss ee eee 33 2 www kontron com 1 Introduction The information contained in this manual may be subject to technical alteration particularly as a result of the constant upgrading of Kontron products The attached documentation does not entail any guarantee on the part of Kontron with respect to technical processes described in the manual or any product characteristics set out in the manual Kontron does not accept liability for printing errors or other inaccuracies in the manual unless it can be proven that Kontron is aware of such errors or inaccuracies or that Kontron is unaware of these as a result of gross negligence and Kontron has failed to eliminate these errors or inaccuracies for this reason Kontron expressly informs the user that this manual only contains a general description of technical processes and instructions which may not be applicable in every individual case In cases of doubt pleas
13. The front surface of the touch screen is a flexible plastic foil so care should be used to avoid using sharp objects such as knife pen or pencil tips Sharp objects can permanently damage the functionality of the touch screen www kontron com 9 Technical Data OmniView 156 OmniView 185 OmniView 215 TFT LCD Screen size 15 6 18 5 21 5 Display Active area 344 2 x 193 5 409 8 x 230 476 6 x 268 1 H x V mm Resolution 1366 x 768 1366 x 768 1920 x 1080 H x V pixel SVGA XGA SXGA Pixel Pitch 252 x252 300 x 300 248 x 248 H xv mm Colour depth 16 7M 16 7M 16 7 M Backlight Brightness cd m Control signal 1x 6bit LVDS 1x 6bit LVDS 2x 8bit LVDS r 1 u d Contrast ratio 500 1 1000 1 5000 1 DC IN Power Plug On the bottom side DC external 24 V power source limited power source AC via the optional external AC DC adapter limited power source VESA 75 100 compliant 9 1 Electrical Specifications OmniView DC 24 VDC 20 A max 1 25 A OmniviewAc 115 220 VAC 20 Hint for DC power connection The OmniView must be connected only to a LPS Limited Power Supply DC mains power supply complying with the requirements of UL IEC 60950 1 gt Hint for Using the Supplied AC power connection Use only a LPS Limited Power Supply power supply complying with the requirements of UL IEC 60950 1 to connect the OmniView to an AC power source www kontron com 9 2 Mechanical Specifications
14. afety and to ensure correct use of the device The chapter also contains information on approval and interference suppression of your device The device has been built and tested by Kontron in accordance with UL IEC 60950 1 and left the premises in a perfectly safe condition In order to maintain the safe condition and ensure safe operation the user must observe the instructions and warnings on the device and in the manual The device must be used in accordance with the instructions for use The electrical installations in the room must correspond to the requirements of the local country specific regulations Take care that there are no cables particularly power cables in areas where persons can trip over them Do not use a power cable in sockets shared by a number of other power consumers Do not use an extension cable For DC power connection The unit is only completely disconnected from the DC main power source when the DC power cord is disconnected either from the power source or the unit Therefore the DC power cord and its connectors must always remain easily accessible Do not place the device in direct sunlight near heat sources or in a damp place Make sure the device has adequate ventilation Only devices and components which fulfill the requirements of an SELV circuit safety extra low voltage in accordance with UL IEC 60950 1 may be connected to the interfaces of the system All plugs on the co
15. ce connector This connector provides connection from the touch screen to the reguired CPU Computer This cord is available as an option and only reguired if the touch screen function is reguired 6 3 5 2 DVI D Video Connector The DVI D supports both digital and analog connections Digital devices can be connected directly to this interface of the OmniView Analog devices should be connected to this interface via a DVI to VGA adapter not included 6 3 5 3 DisplayPort Video Connector One Display Port DP connector comply with Display Port 1 14 specification 6 3 5 4 VGA input VGA input is obtained by connecting to a standard 15 pin D sub female connector via a standard VGA style cable not supplied www kontron com 6 4 VO Panel View Fig 8 1 O panel of OmniView 1 USB B style connector for 4 DVI D female connector touch panel functionality 5 VGA input 15 pin HD Sub 2 DC power in connector female 3 Display Port input IS When powering on the OmniView make sure that the air intake and exhaust openings are not obstructed www kontron com 6 5 Rear Side Fig 9 Rear side of OmniView 1 Slots to attach mounting clamps for 3 Touch Monitor Base air vents securing the system to an Instrument panel 2 slots per clamp 4 Product Identification label area 2 Mounting clamps 6x Note for mounting clamps The OmniView 15 6 18 5 21 5 will be secured into an instrument panel or cabinet wi
16. e contact Kontron This manual is protected by copyright All rights are reserved by Kontron Copies of all or part of this manual or translations into a different language may only be made with the prior written consent of Kontron Kontron points out that the information contained in this manual is constantly being updated in line with the technical alterations and improvements made by Kontron to the products and thus this manual only reflects the technical status of the products by Kontron at the time of printing 2014 by Kontron Printing and duplication even of sections is only permissible with the express approval of Kontron Kontron 14118 Stowe Drive Poway CA 92064 7147 www kontron com 3 1 1 Symbols used in this Guide Meaning This symbol indicates the danger of injury to the user or the risk of damage to the product if the corresponding warning notices are not observed This symbol indicates that the product or parts thereof may be damaged if the corresponding warning notices are not observed This symbol indicates general information about the product and the user manual This symbol indicates detailed information about the specific product configuration This symbol precedes helpful hints and tips for daily use Microsoft MS DOS Windows 7 Windows 8 and Windows NT are registered trademarks of the Microsoft Corporation IBM PC AT OS 2 and PS 2 are registered trademarks
17. htness 7 300 cd m typical 300 cd m typical 300 cd m typical Color Depth 16 7 million colors 16 7 million colors 16 7 million colors Contrast Ratio 500 typical 1000 typical 5 000 4 typical Response Time 8 ms typical 5 ms typical 16ms typical Panel Backlight LED LED LED Table 2 Touch Specifications HMI OV156 xxxx HMI OV185 xxxx HMI OV215 xxxx Specification Model Touch Technology i Projected capacitive system Projected capacitive system j Projected capacitive system Sensor stack thickness EE E 11mm i 1 1mm 11mm Cover glass thickness 1 1 0 2mm 1 1 0 2mm 1 1 0 2mm Touch Method Fingers and thin gloves Fingers and thin gloves Fingers and thin gloves Touch Point 6 touches 6 touches 6 touches 25ms 25ms 25ms EEN USB 2 0 USB 2 0 USB 2 0 6 2 Product Images OmniView 21 5 AC PSU other units similar Fig 1 Bottom view Fig 2 Right view Fig 3 Front view Fig 4 Left view Fig 5 Top view Fig 6 Rear view www kontron com 6 3 Front View Fig 7 Front view of the OmniView 1 TFT display with touch screen 2 Front border www kontron com 6 3 1 Display with Touch Screen Depending on the OmniView ordered the built in display is a 15 6 18 5 21 5 size TFT display with corresponding Projected Capacitive touch screen The touch screen is USB connected For technical specification of the built in display refer to chapter 9 Technical Data
18. ion of the laws of the Member States relating to electromagnetic compatibility If the user modifies and or adds to the eguipment the prereguisites for the CE conformity declaration safety reguirements may no longer apply Generic standards Emission standard for residential commercial and light industrial environments Emission EN 61000 6 3 Emission of Information technology eguipment Radio disturbance characteristics Limits and methods of measurement EN 55022 A ITE Immunity characteristics Limits and methods of measurement EN 55024 4 2 FCC Statement USA This eguipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the eguipment is operated in commercial environment This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense 4 3 EMC Compliance Canada The method of compliance is self declaration to Canadian standard ICES 003 English This Class A digital apparatus complies with the Canadian ICES 003 French Cet appareil num rique
19. many demanding applications The rugged design offers excellent mechanical stability suitable for operation in harsh industrial environments The OmniView is a touch monitor The touch monitor base includes a display and touch screen The following sections detail each of these components and their function in the OmniView www kontron com 6 1 OmniView Touch Monitor Base The touch monitor base is configurable during ordering as a 15 6 18 5 or 21 5 display size Each touch monitor base is eguipped with a color TFT LCD screen and multi point projected capacitive touch screen PCAP The OmniView is fanless cooling of the display is through the surface of the display bezel and air openings located on the top and bottom on the rear of the display bezel The tables below detail the technical specifications of the touch monitor available options IJ When operating the OmniView make sure the air openings on the rear of the display bezel are unobstructed IJ The OmniView Touch Monitor is designed to comply with IP65 protection class at the front side Table 1 Display Specifications HMI OV156 xxxx HMI OV185 xxxx HMI OV215 xxxx Specification Model Viewable image size diagonal 39 6cm 15 6 47 01cm 18 51 54 6cm 21 5 Active Area 344 232mm H x 193 536mm V 409 8mm H x 230 4mm V 476 64mm H x 268 11mm V Maximum Resolution 1366 x 768 i 1366 x 768 i 1920 x 1080 252 x 252 300 x 300 0 248 x 0 248mm Brig
20. mpt to modify the supplied power supply or use an unapproved power cord set that is not the exact type required You must use a power cord set that meets the following criteria Rating In the U S and Canada cords must be UL Underwriters Laboratories Inc Listed CSA Canadian Standards Organization Certified type SJT 18 3 AWG American Wire Gauge Outside of the U S and Canada cords must be flexible harmonized lt HAR gt or VDE Verbena Deutscher Electrotechniker German Institute of Electrical Engineers certified cord with 3x 0 75 mm conductors rated 250 VAC Connector wall outlet end Cords must be terminated in grounding type male plug designed for use in your region The connector must have certification marks showing certification by an agency acceptable in your region and for U S must be listed and rated for 125 of the overall current rating of the server Connector OmniView end The connector that plugs into the DC power receptacle on the I O panel of the OmniView must be an approved power connector approved by Kontron America Molex power series 5539 Cord length and flexibility Cords must be less than 4 5 meters 14 8 feet long The system is only completely disconnected from the main power supply by disconnecting the power from the unit or from the wall supply www kontron com 6 3 5 Interfaces 6 3 5 1 USB 2 0 Connector The system is eguipped at the bottom side with 1x USB 2 0 type B interfa
21. nnection cables must be screwed or locked to the housing wherever possible The device is designed to be mounted and operated only in the position described in this document The proper mounting is a vertical or close to position with the interfaces downwards This device generates heat during operation Make sure it is adequately ventilated Do not cover the ventilation holes in the display housing Maintenance or repair on the open device may only be done by qualified personnel authorized by Kontron who is aware of the associated dangers The device has no components internally that requires access or any set up by Kontron personnel If the unit malfunctions or a situation is encountered that requires that the unit be opened then return to Kontron for maintenance Only approved original accessories optional parts approved by Kontron may be used 6 www kontron com The DC input must fulfill SELV requirements of UL IEC 60950 1 standard Safe operation is no longer possible when o thedevice has visible damage o thedevice no longer functions In these cases the device must be shut down and secured against unintentional operation 3 1 Electrostatic Discharge ESD A ta A sudden discharge of electrostatic electricity can destroy static sensitive devices or micro circuitry Therefore proper packaging and grounding techniques are necessary precautions to prevent damage Always take the following precauti
22. of the International Business Machines Corporation Intel and Pentium are registered trademarks of Intel Corporation AML is a registered trademark of American Megatrends Inc Other product names cited in this manual may also be trademarks and are used here solely for identification purposes 2 Important Instructions This chapter contains safety instructions which must be observed when using the OmniView The manufacturer s instructions provide useful information on your OmniView 2 1 Note on the Warranty Due to their limited service life parts which by their nature are subject to a particularly high degree of wear wearing parts are excluded from the warranty beyond that provided by law This applies to batteries and to the display backlighting for example 2 2 Exclusion of Accident Liability Obligation Kontron shall be exempted from the statutory accident liability obligation if the user fails to observe the safety instructions 2 3 Liability Limitation Exemption from the Warranty Obligation In the event of damage to the device caused by failure to observe the hints in this manual and eventually on the device Kontron shall not be reguired to honor the warranty even during the warranty period and shall be exempted from the statutory accident liability obligation www kontron com 5 A 3 General Safety Instructions for IT Eguipment Please read this chapter carefully and observe the instructions for your own s
23. ons 1 2 Transport boards in ESD safe containers such as boxes or bags Keep electrostatic sensitive parts in their containers until they arrive at the ESD safe workplace Always be properly grounded when touching a sensitive board component or assembly Store electrostatic sensitive boards in protective packaging or on antistatic mats 3 1 1 Grounding Methods By adhering to the guidelines below electrostatic damage to the device can be avoided 1 N sbs D H www kontron com 7 Cover workstations with approved antistatic material Always wear a wrist strap connected to workplace Always use properly grounded tools and equipment Use antistatic mats heel straps or air ionizers for more protection Always handle electrostatically sensitive components by their edge or by their casing Avoid contact with pins leads or circuitry Turn off power and input signals before inserting and removing connectors or connecting test equipment Keep work area free of non conductive materials such as ordinary plastic assembly aids and Styrofoam Use only field service tools which are conductive such as cutters screwdrivers and vacuum cleaners Always place drives and boards PCB assembly side down on the foam 4 Electromagnetic Compatibility Class A Device 4 1 Electromagnetic Compatibility EU This product is in conformity with the protection reguirements of EU Council Directive 2004 108 EC on the approximat
24. s Similar 13 663s PLONE VIEW soos 24 445463506 a k eae E 14 63 1 Display with Touch Sereen use ss RE tiedet e N p O Red PRI 1 5 OS wee PRONE BLAVE zis op A AR EE o A AE 15 623 32 Calibrating the Touch Screen 22 80 DRR V 15 6 324 Power and Grounding seks se EU Sod NES Ee ARE DEE wl AS SR EE RE eS 16 Os N oos de AA RE EE o o OR ER OR OO EE EE AN 17 Ga 1 0 Panel ES AR OE OE N OR EE EO Fm ells sevens 18 6 55 Readr SUDE HAAT OR TE TR EE a aw EE EE OE 19 7 Installation Instructions ss ss ss ss SE ss ee ee ne ee ee ienr Pess is 20 8 Maintenance and Prevention sis ss ss ss ss ee ss ss eee ne eee Ee se se se ee 21 8 13 Touch Screen Care and Cleaning sis sesse Res 0060 8460 a ka 21 9 Technical Data sia 6 46 54 SS ee ee ERE Se obs I Se ai 22 els Electrical SPOGIELEAL ONS Va WENE EE se RES VR EWE Soe u BOSE ERENS dom Sus Se Sad ees Bogan 22 Ose Mechanical SpEEEEDEAELSOMS ER A O 23 9 3 Environmental Specifications sk vis da a 23 10 Regulatory and Certification Information ss ss SS ss SS SS eee eee 24 10 1 Product Regulatory Compliance ss ss ss ss ss ss ss ee eee ee 24 LOL Ls BEodHEE Safety Compl iranek RE tha BAR Bie NE ee Re ER REDS DRR GE arate a 24 10 1 2 Product EMC Compliance Class A Compliance sesse stacas pe ss ss ss se eee 24 10 1 3 Certitftications Registrations Declarati nsS iss 8084 Giese as 24 11 Technical Appendix Interfaces 0 0 0 0 0 0 eee eee eens 25 11 1
25. ted in grounding type male plug designed for use in your region The connector must have certification marks showing certification by an agency acceptable in your region and for U S must be listed and rated for 125 of the overall current rating of the server e Connector OmniView end The connector that plugs into the DC power receptacle on the I O panel of the OmniView must be an approved power connector approved by Kontron America Molex power series 5539 e Cord length and flexibility Cords must be less than 4 5 meters 14 8 feet long e See section 5 1 for details of cords approved by Kontron www kontron com 11 2 DVI Input Connector Connector CN100 DVI D24P Pin No SIGNAL DESCRIPTION 1 TMDS DATA2 TMDS DATA2 Differential negative signal 2 TMDS DATA2 TMDS DATA2 Differential positive signal 3 TMDS DATA2 Shield Shield for TMDS channel 2 4 NC Not connected 5 NC Not connected 6 DDC Clock Clock DDC Interface 7 DDC Data Data DDC Interface 8 NC Not connected 9 TMDS DATA1 TMDS DATA1 Differential negative signal 10 TMDS DATA1 TMDS DATA1 Differential positive signal 11 TMDS DATA1 Shield Shield for TMDS channel 1 12 NC Not connected 13 NC Not connected 14 5V Power 5V for EDID un powered monitor 15 GND for 5V Ground 16 HPD Hot Plug Detect 17 TMDS DATAO TMDS DATAO Differential negative signal 18 TMDS DATAO TMDS DATAO Differential positi
26. th two mounting clamps on the top and bottom surfaces and one on each the left and right surfaces as shown in fig15 position 2 A Please observe the safety instruction for handling assemblies with static sensitive ta device Failure to take heed of this warning instruction can result in damage to the device www kontron com 7 Installation Instructions The OmniView should be installed and operated only by trained and gualified personnel The unit must be placed such that there is sufficient space for connecting the cables to the I O interface connectors The voltage feeds must not be overloaded Adjust the cabling and the external overload protection to correspond with the rated voltage range indicated on the type label The type label is located on the right side of the system The rear access panel must be secured by the supplied screws during operation The mount clamps with screws supplied allow the easy and fast mounting of the OmniView 156 185 215 Refer to the appropriate unit outline and mounting drawing for the correct dimensions of cut outs and air gap clearances required for mounting the unit into a wall or panel The OmniView outline and mounting drawing can be found on our web site www kontron com Dimension for OmniClient 156 185 215 Cut Out for Mounting into a Panel mm W x H Requirements for Mounting Metal mounting panel thickness for proper mounting 394 x 245 462 x 283 527 x 325
27. us make sure to use a special conductive stylus that works with capacitive touch screens www kontron com 6 3 4 Power and Grounding 6 3 4 1 DC power Input The OmniView is supplied by a 24VDC external power supply This can be connected to the mains power by either option of the US power cord or the EU power cord Electrical power disconnect The unit can be disconnected from the electrical supply by either unplugging the 4 pin power connector on the OmniView I O panel or by disconnecting the power supply from the wall supply The power cord s is considered the mains disconnect for the server and must be readily accessible either at the wall or on the unit when installed Grounding the system To avoid an electrical shock hazard you must ensure the system has proper grounding The OmniView power cord includes the safety ground conductor and provides proper grounding only for the OmniView You must ensure proper grounding is provided for the entire system into which the OmniView is embedded You must provide additional proper grounding for the OmniView and the host equipment Overcurrent protection There is no Over Current protection built into the OmniView The external power supply is designed to handle input 100 240 VAC 1 3A 50 60Hz and output 24VDC 1 67A max If overcurrent protection is required beyond the limits of the supplied power supply you must provide supplemental protection for the OmniView WARNING Do not atte
28. ve signal 19 TMDS DATAO Shield Shield for TMDS channel 0 20 NC Not connected 21 NC Not connected 22 TMDS Clock Shield Shield for TMDS clock 23 TMDS CLOCK TMDS Clock Differential positive signal 24 TMDS CLOCK TMDS Clock Differential negative signal 11 3 DVI Connector DVI I The DVI I connector support DVI Digital output and DVI analog output BREE ll aja soas elle mieles OE Figure 2 DVI I Female socket front view Signal Description DVI I connector Pin No Signal Description Type Pull U D 1 TMDS Data 2 Digital Red Link 1 LVDS OUT 2 TMDS Data 2 Digital Red Link 1 LVDS OUT 3 TMDS Data 2 4 Shield PWR 4 NC NC 5 NC NC 6 DDC Clock DDC Clock 10 2K2 7 DDC Data DDC Data 10 2K2 8 NC NC 9 TMDS Data 1 Digital Green Link 1 LVDS OUT 10 TMDS Data 1 Digital Green Link 1 LVDS OUT 11 TMDS Data 1 3 Shield PWR 12 NC NC 13 NC NC 14 5V Power for monitor when in standby PWR 15 GND PWR 16 Hot Plug Detect Hot Plug Detect l 17 TMDS Data 0 Digital Blue Link 1 Digital sync LVDS OUT 18 TMDS Data 0 Digital Blue Link 1 Digital sync LVDS OUT 19 TMDS Data 0 5 Shield PWR 20 NC NC 21 NC NC 22 TMDS Clock Shield PWR 23 TMDS Clock Digital clock Link 1 LVDS OUT 24 TMDS Clock Digital clock Link 1 LVDS OUT C1 ANALOG RED Analog output carrying the red color signal O
Download Pdf Manuals
Related Search