Manual for CH03214
Contents
1. 256 Level Resolution HORI Color 530 TV Line BLC Of Off BLC HSBLC TV Type NTSC DWDR Off Off Indoor Outdoor Sync Type Internal Return Scanning System 2 1 Interlace Video Out 15 734 KHz i ATW AWB AWC Manual Indoor Outdoor White Bal ATW Manual R Gain Level adjust B Gain Level adjust Gamma Characteristic n Dome Camera Scanning Frequency H 59 94 Hz 1 0 Vp p Sync Negative Termination 75Q y 0 45 typ Auto Delay S Level E Level Min Illumination Day Night Auto EXT S N Ratio B W Burst Off On Gain Control Color Shutter 1 60 1 100 000 sec Test Illumination Area AVERAGE TEST ILLUMINANCE BY FRONT VIEW 3DNR On Limit 0 100 Level Selectable Off Gutrent Consumption 120mA Max Supplied Voltage Regulated DC 12V 15 Reverse Polarity Protection Yes di new r w ope 0 next Table Operation Temp 10 50 C 14 122 F Preservation Temp 20 60 C 4 140 F 0 1Lux F1 2 Dimension 123 1mm W X 123 5mm D X 84 8mm H Sharpness Adjust Blue Red 45dB or More AGC OFF Automatic Weight Approx 350g poet fe Saves all the SETUP Menu and then exits 0 31 Level Selectable 0 100 Level Selectable 0 100 Level Selectable Special Function Day amp Night Color BW Auto EXT BLC BLC HSBLC OFF amp DWDR selectable Blemish Compensation 256 Point Even 128 point Odd 128 point Auto Off Selectable limit x2 x256 English Korean Chinese Japanese On Off 4 Zone Off On 02. with the instruction manual it may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at own expense CAUTION Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Diagram amp Adjustment Angle Adjustment 1 Pan adjustment Grasp the lens cover and then adjust direction to the right or left D 180 180 2 Tilt adjustment Grasp the lens cover and then adjust direction to the up or down A 18 90 or B 21 90 3 Roll adjustment grasp the lens cover and then rotate C 180 180 Removing Mount Bracket 1 Push the button inside of main body and turn the main body counterclockwise 2 Detach the main body from mount SS Main Product User Manual Mount Bracket Screws amp Anchor OSD Menu Structure 1 Specification Setup Meru Defaut Ser O voe CH 03214 Scanning Frequency V Image Sensor 1 3 Sony SUPER HAD II CCD Shutter Shutter FLK 1 50 1 100000 MANUAL x256 Effective Pixel 768 H x 494 V Brightness z Brightness 0 100 Level Cell Size 6 35um H x 7 4um V AGC Middle Off Low Middle High Exposure Sens_up Auto Off Auto 2
3. 100 Level Adjustable On x32 Off On Off 8 Zone OSD Menu Structure 2 Special Menu Default Set Sens up Camera Title Off On OSD Language On Off Horizontal Freeze Off On Off Motion Detection Mirror Off Off Mirror V Flip Rotate DNR D Zoom Off On D Zoom x 32 PAN 100 TILT 100 Off Digital Zoom D Effect Gamma 0 45 0 05 1 0 Selectable Privacy Neg Image Off ed On Mirror H REV S Flip V REV On Off Vertical CamID 1 255 Selectable Ua On Off RS485 ID Display Off On Sharpness Level Adjustable Baudrate 2400 4800 9600 19200 38400 57600 Width 0 100 Top Bottom 0 100 Height 0 100 On Area Select 1 4 Troubleshooting Motion Area Display On Off If you have a trouble operating your camera refer to the following Left Right 0 100 If the guidelines do not enable you to solve the problem contact an authorized technician Sensitivity 0 40 Motion View Off On Area Select 1 8 Area Display On Off Left Right 0 100 Width 0 100 Top Bottom 0 100 Height 0 100 Color 0 15 INT LL English English Japanese Chinese Korean The image does not appear on the screen The image on the screen is dark The surface of the camera case is hot and a black line appears on the screen The screen blinks a lot Check the power source for the monitor and camera and assure that the voltage and polarity are properly connec
4. CH 03214 DOME Camera CAUTION To prevent electric shocks and risk of fire hazards DO NOT use other than specified power source CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL the user to the presence of important operating and maintenance servicing instructions in the literature A To prevent fire or shock hazard do not expose the unit to rain or moisture The symbol is intended to alert SA 1966 accompanying the appliance The symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be sufficient magnitude to constitute a risk of electric shock to persons SA 1965 Installation Installation 1 Opening the dome Push the latch button SCREW TP1 E 4X30 3EA 3 Camera installation amp Lens adjustment 1 Fix the mount bracket with supplied screw on ceiling or wall mount X Note The camera front sign is on the mount bracket 2 Attach the main body to the mount bracket by rotating it 3 By turning the Tele Wide knob you can access a range of focal lengths 4 Since then by turning the Near Far knob you can set the focus 5 Reassemble dome case lt Focus Adjustment gt 1 Do not attempt to disassemble the camera In order to prevent electric shock do not remove screws or cover 2 Handle the camera with care T
5. he camera could be damaged by improper handling or storage 3 Do not expose the camera to rain or moisture or try to operate in wet areas Take immediate action if the camera becomes wet Turn the power off and request service to qualified personnel Moisture can damage the camera and also create a risk of electric shock 4 Do not use strong or abrasive detergents when cleaning the camera body Use a dry cloth to clean the camera when dirty In case the dirt is hard to remove use a mild detergent and wipe gently 5 Never point the camera toward the sun Whether the camera is used outdoor or not never point it toward the sun Use with caution when operating the camera in the vicinity of spot lights or other bright lights and light reflecting objects 6 Do not operate the camera beyond its temperature humidity or power source ratings Do not use the camera in an extreme environment where high temperature or high humidity exists Use the camera under conditions where temperatures are between 14 F 122 F 10 C 50 C and humidity is below 85 This equipment has been tested and found to comply with the limits for a Class A Digital device Pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance
6. ted and being supplied correctly Check if the lens is stained If dirty clean the lens with a soft clean cloth Adjust the contrast feature of the monitor and DC level Check if you have connected the camera to a proper power source and if there is no problem with the power turn the unit off immediately and seek assistance from our After Service department Check if the camera is pointed toward the sun or a fluorescent lamp Adjust the angle or location of the camera if too much light is coming into the screen
Download Pdf Manuals
Related Search