TDG133 - GSM Bidirectional Remote Control 2 IN / 2
Contents
1. aep nei rir n mera Conan dE Ta pula Mumam SEEN La UTURA A ELETTRONICA zl Numen Mader pscancele nue paeem complelo al soebena La fon pene meum pala ora uscia Mumam ee a Honma LOG Porta DOMES Agarta DOO S N A con 19 106185 Management of phone numbers enabled for the control of the device and of those related to the gate control function is done through the folder Telephone Numbers It is possible to store or delete the enabled numbers and to request the full list visible on the right of the window of those numbers in the device Every selected operation Store Delete or Request Full List must be confirmed by pres sing 20 Porta COMM Aperta GON USER MANUAL E e ei 2 Agen RA d Uscite Names Master Mamet Din del med del dena d 10411234567 Mattes Conii la memep razione del numero 332451 nella liste P apricancella Fosscne 1 HAST Home ger 5 Memoirra Cancels Pichied Liste Complet2. Reply to the message with command RISP is disabled or there is no credit in the SIM Card The device has already been started The mobile used for the call has a hidden ID Check power supply cable Change the position of the external GSM antenna Do not use the RISP command in the SMS or recharge the SIM Card Completely reset the device using the RES command Enable the ID on outcoming calls The device cannot engage The PIN on the SIM Card Disable the PIN request from in the GSM network has not been disabled the SIM Card The information in this manual is subject to change without notice Technical Assistance In case of technical problems or questions concerning the TDG133 a hotline is available Mon and Wed 2 pm 6 pm CET Central Europe Time Technical assistance 39 0331 245587 futurel 23 C 0051 Complies with all applicable european directives Produced and distributed by FUTURA ELETTRONICA SRL Via Adige 11 21013 Gallarate VA Tel 0331 799775 Fax 0331 792287 web site www futurashop it technical Information supporto futurel com futurel Relase 27 09 2010 V I 1 0 V F 2 0
3. call made on start up When the device is supplied with power LD5 will immediately flash at 1 Hz frequency The TDG133 will try to connect to the GSM network when connected LD5 will briefly flash every 2 seconds or so After the system initialization which may take several se conds the device alternately illuminates yellow LEDs LD3 and LD4 to indicate the configuration call on hold which should take place within 3 minutes If during this time the unit receives a call it stores the caller s number to which reply SMS will be sent in the first memory location it turns the two LEDs off and becomes operative otherwise at the end of the interval it switches off the yellow LEDs and waits for the configuration SMS PROFESSIONAL SETUP mode With the same phone used to make the first setup call it is also possible to switch the relay status This mode allows for simple commands without sending SMS or using a computer 2 PROFESSIONAL SETUP Configuration through SMS executable at any time This mode takes full advantage of the device with operations as output switch output status query inclusion of additional phone numbers to activate the relay inclusion of numbers for door opening function reception of reply messages change output signals timing and in general set the TDG133 with all parameters via simple SMS A full reset to restore the default settings can also be made via SMS The syntax for all available commands can be
4. found in Section 11 Configuration SMS 3 Computer SETUP Configuration through PC connection This mode easily allows you to setup the TDG133 with no additional cost through a computer with a special software connected via USB code FT782M optional Chap ter 13 provides all the necessary information to make the best use of this configuration mode Configuration through call Turn on the device wait till the yellow LEDs LD3 and LD4 start to flash alternately then with the mobile used to control the TDG133 call the phone number corresponding to the SIM Card in the remote The device will reject the call and store the caller number in the first memory location LD3 and LD4 will flash rapidly to indicate the operation Check that the mobile used for the configuration has an active ID i e the hidden call or private cal has not been enabled To return to the standard configuration with active ID please refer to the mobile instructions manual To check your own mobile configuration simply call another mobile The caller ID is active if it displays the number tse USER MANUAL TDG133 or name of the calling mobile NOTE Yellow LEDs LD3 and LD4 lighten up alternately until the TDG133 is set up with a call within the first three minutes of start up If time is up and no configuration has been made the TDG133 turns off the two LEDs and waits for the configuration SMS The EASY SETUP mode can be re
5. get setting 00 the relay clicks and remains excited until the arrival of a new call from the same number in the list that has caused the activation or from another number enabled for gate control Command MAC 39xxxxxxxxxx pwd stores the phone numbers that control the gate opener function only xxxxxxxxxxx is the phone number you want to store in the list 200 numbers max with international code 39 for Italy pwd is the current pas sword The password is required Example How to store number 3339999999 being 12345 the password MAC 393339999999 12345 futurel 15 USER MANUAL Note 1 For the gate control function there is no specific storage position Each num ber is saved in the first available position it follows that in order to delete a number it is necessary to type the number itself in the relevant command not its position Command DAC 39xxxxxxxxxxxx pwd deletes a phone number from the gate con trol list xxxxxxxxxxx is the phone number you want to delete with international code 39 for Italy pwd is the current password The password is required Example How to delete number 3339999999 being 12345 the password DAC 393339999999 12345 Command DAC pwd deletes all numbers in the gate control list pwd is the current password The password is required As already mentioned at the beginning of Chapter 11 the system accepts messages with multiple commands separated by a comma helping the user save time and m
6. the storage of the first master number the message Waiting for Call for Master Num ber Storage will appear on the log window down In order to continue with the setting make the call so as to store the number The execution will be confirmed with a message on the log window In the Information tab you can find the IMEI and the firmware version of the connected device In order to modify the access password stored on the device type in the fields Old and New the desired password and press To access the system and make all possible settings please type the current password in the field System password then press Confirm If the device does not re ply to the commands sent from the computer make sure the password stored in the PC is the same as the one specified in the management program futurel Peria 2000 komana Scheda Medie IMEI Porna Aperta DOE NOT A TD Esti Database j COM COM 1d 320 Teo Debe Scheda Figen dd dapcatva ala d Medele Ferma 10 Dae E e ra 1235 H di ati ___ _ 8 iustae per coniun sone 12345 UTURA ELETTHONICA Mursen Masher Ls
7. 2 LOW Example How to set the alarm text NO TENSION ON INPUT 2 for input 2 in absen ce of tension TIN2B NO TENSION ON INPUT 2 Note Keep in mind that messages will be sent from the remote control according to the settings made in relation to the logic level intended as an alarm The operation mode the timing and the status requests of the input relays can be ma naged by SMS Command OUTx ON activates the specified output relay x is the output relay 1 or 2 Example How to activate output relay 1 OUT1 ON Example How to activate output relay 2 OUT2 ON Command OUTx OFF disables the specified output relay x is the output relay 1 or 2 Example How to disable output relay 1 OUT1 OFF Example How to disable output relay 2 OUT2 OFF Command STA requests the condition of the remote outputs Example STA Command OUTx ss inverts the condition of the specified relay for the desired time x is output relay 1 or 2 ss is a period between 1 and 59 seconds Example How to disable output relay 1 if already active or how to activate it if not active for 10 seconds OUT1 10 In case of black out command RIPx stores the relay status and restores it when po 14 futurel USER MANUAL TDG133 wer is back on x has a value of 1 to enable restoring to disable it The default value is 1 Example How to enable the relay status recovery on start up RIP1 Example How to disable the relay status recovery on start up RIPO Comma
8. 33 65 Memonrzanone nume beta Apecancelie 0340 42 Richiesta numer Apacancelio Porta Aperta 9600 8 N 1 Dispositivo rilevato e connesso 550350 AMY SCARICO TUTTA LA MEMORIA AD INIZIATO Onn On Ons OK USER MANUAL The software version can be seen pressing on the menu bar Important Management via SMS is disabled when the TDG133 is connected to the computer 14 Troubleshooting IDG133 About Configuratore TDG cor racone per le unit w fonto gatuteserte da Future e non necessita d Jon tpe d Ne vetita la dvuiganone bi ueo commercole Per rformanone tecrace o assistenza betefonicamerte Lo The following table presents the possible solutions to some problems that may arise Problem Green LED LD5 is off Green LED LD5 flashes cyclically at 1 Hz frequency The device does not send a reply to the configuration SMS During the first start up LEDs LD1 and LD3 do not lighten alternatively The device does not react to the call from an enabled number Possible reason No supply tension or inverted polarity No GSM network available or signal intensity not enough
9. ON IN BISTABLE MODE OUTx OFF CHANGE OF MONOSTABLE RELAY STATE 01 59 OUTx ss seconds RELAY RESET x is 1 to obtain reset 0 to have the relays disabled INPUT AND OUTPUT STATUS REQUEST SEND SMS ON START UP x has a value of 1 for activa AVVx tion and 0 for deactivation STORE NUMBER FOR DELETE NUMBER FOR TOTAL DELETION OF GATE CONTROL LIST except for DAC YES the first 8 numbers continues on next page futur 17 133 USER MANUAL Continuation of Table of command and configuration SMS PWD REQUI FUNCTION DEFAULT VALUE RED TIME FOR GATE CONTROL ACTIVATION ss 00 bistable 59 JUL TIN 1A200000000X ALARM INPUT 1 HIGH ALARM TEXT INPUT 1 IF NO TENSION PRESENT max 100 characters ALARM TEXT INPUT 2 IF UNDER TENSION max 100 o E characters deii TENSION 100 TIN2B XXXXXXXXXXX ALARM INPUT 2 LOW ow START UP TEXT MESSAGE 100 characters SYSTEM START UP 13 Managing the device through a computer By means of a computer with a specific software and USB interface code FT82M optional installed directly on the board it is possible to manage all programming and function settings as well as change the list of enabled users This speeds up the initial settings and saves on the cost of SMS After starting the software verify that a communication speed of 9600 Baud 8 N 1 is set Installing and
10. USER MANUAL TDG133 TDG133 GSM Bidirectional Remote Control Technical data GSM GPRS Module SIM900 Quad 850 900 1800 1900 MHz GPRS multi slot class 10 8 GPRS mobile station class Output power Class 4 2 W 850 900 MHz Class 1 1 W 1800 1900 MHz GSM external stylus antenna e Power supply 9 to 32 Vdc stabilized or with Li lon battery 800 1 000 mA h dle current 50 mA idle peak up to 1A Relay outputs 2 to control low tension loads SELV type lt 60 Max current relay contacts 10A Digital inputs 2 logic 1 5 32 V logic 0 0 Vdc Master users 8 Dimensions 103x67x28 LxWxH mm Weight approx 100 grams Operating temperature 10 C 55 14 F 131 F Complies with EN 60950 1 2006 EN 301489 7 V 1 3 1 EN 301511 V9 0 2 future USER MANUAL 10 11 12 13 14 TABLE OF CONTENTS MOO 91421 ALOU QE ES 3 Safety instructions f _ _ _ 3 Er irum ie P 4 Operating 4 aye di 5 IMIG ENC TO lai 6 C nnectors and LEDS 6 installing the USB 7 T E EE E E O E E gt 7 RS ONO UN AON Ea mm 8 lic ERR 9 Tab
11. ctorate Condor ah 161 2 rumes renda lata Vinci LOG Loss Ports COMI Aperta 9600 8 N 1 Dispositivo nleveto 4 commesco A Tempo di inibizione impostato It is possible to ask the device for the current set Ww Ingresso2 5 minuti time ticking on Request Set Time and pressing mE Tempo di osservazione impostato immediately after you will see a window like Ingresso 1 1 secondi the one in the figure where all the requested infor onem mation will appear futurel 21 The tab Outputs is used to enable or disable the function Restore Re lay Status in absence of tension directly manage the relay and set its activation time in gate control mode Pressing Activate Extended Log it is possible to visualize in a specific window all data in transit through the communication port 22 USER MANUAL tes 13600 rfomacers Namen Tocino Uscte savas J ripristino Felt su marcenca olmertasone stato Furl gu aimertazone 23391234567 09 15 55 Pots COM14 aperta con successo 09 36 15 Dapeatvo devo conneemone i conso 093617 Croderuish 03 39 10 Memorazanone numaro rala Mta Apscancels 08 38 11 Mecrttzato primo numero 293491234567 nella ista Master mediate chamata numan rela lata Maser 08
12. digits pwd is the current password The default password is 12345 Example 54321 as the new password and 12345 as the current password PWD54321 12345 Command NUMx 39nnnnnnnnnnn pwd stores a phone number up to 8 numbers 19 digits each in the device x is its position in the list nmnnnnnnnn is the phone num ber with country code 39 for Italy pwd is the current password Example how to enter number 3498911512 in the 8th position NUM8 393498911512 12345 USER MANUAL Note the password is required only if you try to save the number in a position already occupied by another one or when the command is sent from a phone that is not in the list If the command is sent from an unknown phone the password is always required Command NUMx pwd removes a phone number from the list x is its position in the list pwd is the current password Example how to remove from the stored list the 4th telephone number NUM4 12345 Note the password is required Command NUM pwd requests the list of phone numbers currently stored in the device pwd is the current password Example NUM 12345 Note the password is required Command RES pwd resets the initial settings default of the system and deletes all stored phone numbers pwd is the current password Example RES 12345 Note the password is required The remote can send SMS to the phones of the people that must be advised of a change in the inputs status The follow
13. elds of application include gate opening control of power loads switching on and off alarm devices reception of information concerning the state of door sensors movement sensors level sensors etc all through SMS 7T Connectors and LEDs As shown in picture 1 the TDG133 remote control has a terminal for connection with different external units Pairs INT and IN2 are two opto isolated inputs while the other two pairs OUT1 and OUT2 correspond to the NC NO and C contacts of the two relays Connect the supply tension of the device to the outlet marked PWR center positive Via USB optional directly installed on the card you can connect a computer with the special TDG Configurator software it is possible to make all programming and function setting or change the list of authorized users When the device is engaged in the GSM network research LD5 flashes at 1 Hz frequency when it is hooked in the network it will flash briefly every 2 seconds the LED is on only when the module receives a call LD1 and LD2 indicate the status of the relays LD3 and LD4 indicate the status of the inputs LD1 on Relay 1 active LD2 on Relay 2 active LD3 on IN1 active logical condition set reached LD4 on IN2 active logical condition set reached LD3 and LD4 also report SMS reception both of them flash for a few seconds CALL reception both LEDs on and CONFIGURATION CALL on hold both LEDs turn on alternatively af
14. er than a SMS which may arrive with some delay Command VOCxxxxxxxx ON allows the number on the specified position to receive the ringtone on the inputs status x is the position of the number s in the list Example How to allow phone numbers on positions 1 and 5 in the list to receive a ringtone on inputs status VOC15 ON Note 1 The command will only modify memory positions 1 and 5 and not the state of the other ones 2 3 4 6 7 8 if the latter are already enabled to receive the alarm ringtone for example because previously activated they will continue receiving it Note 2 The password is required Command VOOCxxxxxxxx OFF does not allow the number in the specified position to receive the ringtone on the inputs status x is the position of the number s in the list Example How not to allow phone numbers on positions 2 and 4 in the list to receive a ringtone on inputs status VOC24 OFF Note 1 The command will only modify memory positions 2 and 4 and not the state of the other ones 1 3 5 6 7 8 if the latter are already enabled to receive the alarm ringtone for example because previously activated they will continue receiving it Note 2 The password is required Please note that by default all the phone numbers in the first eight positions of the list provided they are stored receive a notification of the input alarm via SMS or short call ringtone The same applies if the reset command which restores the initia
15. he intended field of application In case of doubt please contact a qualified technician or the Manufac turer Dealer The Manufacturer Dealer cannot be held responsible for improper handling or wrong connections therefore it cannot be held responsible for any damage that may result Devices that operate with 35 Volts must be connected by a qualified technician Before starting the device check there is no current leakage in the housing f measurements are to be made with an open housing an isolating transformer has to be integrated for safety reasons Alternatively tension can be supplied by a power supply that complies with all safety regulations limitations in current and tension All wiring work has to be done in a tension free state 3 General information For EU residents Environmental information related to this product This symbol on the device or package indicates it is forbidden to dispose of the product in the environment at the end of its lifecycle as it could be har mful for the environment itself not dispose of the product or batteries if used as unsorted waste EN more information about the recycling of this product please contact the city hall your local waste disposal service or the shop where it was purcha sed 4 Operating conditions Warning before making connections to the device carefully verify that the supply ten sion and the tension applied to the relay contacts corre
16. ing commands enable or disable that function only valid for the numbers in the list Command SMSxxxxxxxx ON allows the number in the specified position to receive SMS on input status x is the position of the number s in the list Example How to allow phone numbers on positions 1 and 5 in the list to receive the SMS on inputs status SMS15 ON Note 1 The command will only modify memory positions 1 and 5 and not the state of the other ones 2 3 4 6 7 8 if the latter are already enabled to receive alarm SMS for example because previously activated they will continue receiving those messages Note 2 The password is required Command SMSxxxxxxxx OFF does not allow the number on the specified position to receive SMS on inputs status x is the position of the number s in the list Example How not to allow phone numbers on positions 2 and 7 of the list to receive SMS on inputs status SMS27 OFF 10 futurel USER MANUAL IDGISS Note 1 The command will only modify memory positions 2 and 7 and not the state of the other ones 1 3 4 5 6 8 if the latter are already enabled to receive alarm SMS for example because previously activated they will continue receiving those messages Note 2 The password is required In addition to SMS the device can also make short calls to ring the phones of the people which number is in the list that must be advised of a change of input status the ringtone draws people s attention fast
17. ithin a shorter time than the interval of inhibition restore will take place at the next input activation The device lets you define how long the alarm condition must be for a certain input so that the circuit sends the notifications The setting is made through the following mes Sages Command OSS1 ss defines the length of the observation time regarding input 1 ss is the time in seconds Example How to set a ten second observation time for input 1 OSS1 10 Command OSS2 ss defines the length of the observation time regarding input 2 ss is the time in seconds Example how to set a 59 second observation time for input 2 OSS2 59 Note The observation time can be set between 1 and 59 seconds The default value for both inputs is 1 second Command OSS requests the current observation time setting regarding the inputs Example OSS Regarding the inputs activity it is possible to define for each of them the notification message about presence of tension as well as for the one for absence of tension Command TIN1A xxxx defines the message the device sends to the numbers in the list enabled to receive alarm SMS when input 1 gets the alert of tension presen ce xxxx is the message you want to write 100 characters max including spaces The text message does not accept the semi colon and all letters must be capitalized The default message is ALARM INPUT 1 HIGH Example How to set the alarm text TENSION ON INPUT 1 f
18. l settings is sent to the remote control It should be noted that these notifications can be made only to the eight numbers stored related to the remote and not to the 200 related to the door control Commands regarding the setting of the level that defines the alarm condition are listed below futurel 11 ILX2122 USER MANUAL Command L Vx A sets a HIGH level as the alarm condition for inputs IN1 or IN2 the input is in alarm under tension x stands for input 1 or 2 Example How to set a HIGH level of alarm activation on input 2 LIV2 A Command LIVx B sets a LOW level as the alarm condition for inputs IN1 or IN2 the input is in alarm in absence of tension x stands for input 1 or 2 Example How to set a LOW level of alarm activation on input 2 LIV2 B Command LIVx V sets a level variation as the alarm condition for inputs IN1 or IN2 the input is in alarm after going from a LOW level to a HIGH level or the opposite x stands for input 1 or 2 Example How to set a level variation as alarm activation on input 1 LIV1 V Please note that By default inputs are activated in presence of tension Command LIV requests the alarm activation level regarding the inputs Example LIV You can define a period of time known as input inhibition time following an alarm ac tivation during this time the device does not control the level on a specific input that period may be set between 0 and 59 prime minutes The default value i
19. le of command and configuration 17 18 Managing the device through a computer 18 er 23 futurel USER MANUAL TDG133 1 Important information Please carefully read the information in this manual before attempting to operate the device in order to protect yourself and use the equipment properly This device shall be exclusively utilized for its intended use In no event shall the company Futura Elettroni ca or its dealers be held responsible for any damage either extraordinary incidental or indirect of any nature financial physical etc arising from the possession use or failure of this product In case of changes to the device tampering or non compliance with the instructions in this manual the warranty will be null and void The device contains highly integrated components that can be damaged by electrostatic discharge Therefore do not touch any metal part tracks ir 4 ponent terminals etc with your hands Only handle the device by the edges in order to avoid touching the compo nents on the board Notice The user who makes the module operational by adding further components or by put ting it into a housing is seen as a manufacturer and is obliged to hand out all the ne cessary technical documentation as well as place his name and address on the device Products made with this equipment have to be considered as industrial products from the safe
20. nd RIP requests the current setting for relay status recovery Example RIP The remote gives the possibility to send a customizable SMS to the phone number on the first position in the list whenever it is fed Command AVVx enables o disables the afore mentioned function x has a value of 1 to enable it to disable it The default value is Example How to enable the function to send a start up SMS AVV1 Example How to disable the function to send a start up SMS AVVO Command TSU xxxxxxxxxxxx sets the text of the message the remote sends during Start up is the message 100 characters max including spaces The text message does not accept the semi colon and all letters must be capitali zed The default phrase is SYSTEM STARTUP Example How to set the start up message TDG140 DEVICE ON TSU DISPOSITIVO TDG133 ACCESO The following describes the commands of the functions for the gate control mode Command TAC ss defines how relay 1 related to the gate control should be enabled when there is an incoming call from one of the 200 phone numbers or one of the 8 numbers in the list ss is the time in seconds during which the relay should remain excited The default value is 3 seconds Example How to set a gate control activation time of 25 seconds TAC 25 Example Gate control activation bistable mode setting TAC 00 Note The time value can be set between 00 and 59 seconds Bistable activation is
21. oney There follows that the system replies to certain commands with more than one SMS This can be avoided by means of a command placed at the beginning of the SMS sent to the TDG133 Command RISP at the beginning of a multiple message disables all reply messages Example How to disable the answer message related to the sent commands RISP OUT1 ON DAC INI1 10 18 futurel USER MANUAL TDG133 12 Table of command and configuration SMS FUNCTION DEFAULT VALUE sum PASSWORD REPLACEMENT 12345 mmm em DELETE A NUMBER A NUMBER E T CN RN ME E wa LIII LOGIC LEVEL HIGH ALARM LIA INPUT UNDER TENSION x can represent 1 or 2 UNDER TENSION LOGIC LEVEL LOW ALARM NO TENSION IN INPUT can represent 1 or 2 IF NO TENSION ACTIVE LOGIC LEVEL ALARM VARIATION LIVx V IF NO TENSION _ INHIBITION TIME INPUT1 00 to 59 min INI1 mm INHIBITION TIME INPUT2 00 to 59 min INI2 mm RESETS INHIBITION TIME IF INPUT IS BACK TO IDLE m INPUT1 x if 0 does not reset 1 if it resets RESETS INHIBITION TIME IF INPUT IS BACK TO IDLE INPUT2 x if 0 does not reset 1 if it resets INHIBITION TIME REQUEST OBSERVATION TIME INPUT1 00 59 sec OSS1 ss OBSERVATION TIME INPUT2 00 59 sec 0SS2 ss RELAY ACTIVATION IN BISTABLE MODE 0 0 RELAY DEACTIVATI
22. or input 1 in presence of tension TIN1A TENSION ON INPUT 1 Command TIN1B xxxx defines the message the device sends to the numbers in the list enabled to receive alarm SMS when input 1 gets the alert of tension absence Xxxx is the message you want to write 100 characters max including spaces The text message does not accept the semi colon and all letters must be capitali zed futurel 13 USER MANUAL The default message is ALARM INPUT 1 LOW Example How to set the alarm text NO TENSION ON INPUT 1 for input 1 in absen ce of tension TINTB NO TENSION ON INPUT 1 Command TIN2A xxxx defines the message the device sends to the numbers in the list enabled to receive alarm SMS when input 2 gets the alert of tension presence XXXxx is the message you want to write 100 characters max including spaces The text message does not accept the semi colon and all letters must be capitali zed The default message is ALARM INPUT 2 HIGH Example How to set the alarm text TENSION ON INPUT 2 for input 2 in presence of tension TIN2A TENSION ON INPUT 2 Command TIN2B xxxx defines the message the device sends to the numbers in the list enabled to receive alarm SMS when input 2 gets the alert of tension absence Xxxx is the message you want to write 100 characters max including spaces The text message does not accept the semi colon and all letters must be capitali zed The default message is ALARM INPUT
23. paired by a qualified technician When repairing the unit original parts must be used The use of differing spare parts can cause serious material loss or personal injury the tracks connecting the relay contacts to the terminal are sized considering a load activation which absorbs 10 A for short periods of time 5 Proper use This device is designed for the remote switching of electric and electronic units via the GSM network and for the remote retrieval of status information of its inputs by means future USER MANUAL of SMS messages automatically generated after those inputs change status A different use is not allowed 6 Introduction The TDG133 is a bidirectional remote control module easy to install and simple to use With the TDG133 it is possible to remotely control two relays in monostable or bistable mode by means of special SMS commands with a password sent from any mobile phone It is possible to store up to 8 telephone numbers to which the device sends SMS and phone calls when according to the settings made during the configuration it considers the inputs active Moreover the device can also be used as a gate control receiver controlled by up to 200 enabled telephone numbers Apart from the TDG133 you will need a valid SIM Card from any network provider GSM 900 1800 MHz When using a prepaid SIM Card always check the available credit so that in case of alarm a SMS can be sent Typical fi
24. s Muse 121312245073 Heme z Horses Hone COM 1 con succes 5 hi iP ions Dispostivee rlevate econnesss USER MANUAL Mamen d Telefone Asem peaa Usata omm Hurren Master Numer Adr se l cenone SMS d Uta cu rumpi Mater VM eR Su xri Fami Ese uo d ad cus c a crake Poo sulla Fon 1 Fon 2 Poa 3 Pos 4 Pea 5 Pea Pea 7 8 Hurme 19349123407 The tab Notice is used to enable or disable the numbers on speci fic positions in the list enabled to receive SMS or alarm calls 16 22 20 Poss OM 14 sts con pce 1822 21 Coocen ah 161 20r berries ruses ista LOG Lewis Porta COMIS Aperta 8600 81 Dispasitreo nleveto commesco rwy tation F Peela COM ioma accrue en NS Come ERETTMONICA Magnes Logica di Alarme Lats dai ramai Martii aftr Miriona dal mater d Su access 1 zi completo ai sistema inches ln funziona Apricancalio Me uscita 241234557 Tempie a Tempo di kiap The tab Inputs is used to define Tesco devas the activation logic High Low aan Variation of the two inputs and their time 32 20 Pome DDH i agat con succes 162221 Re
25. s 5 minutes Command NI1 mm sets the inhibition time on input 1 mm is the time in prime minu tes Command IN I2 mm sets the inhibition time on input 2 mm is the time in prime minu tes Example How to establish that following an alarm IN1 cannot determine other alarms for two minutes INIT 02 Command NI requests the current inhibition time setting regarding the inputs Example INI When it is necessary to control sensors that monitor frequently variable phenomena and to receive real notifications about the current events it might be necessary to ignore the inhibition time The remote can temporarily disable input by input the preset inhibi tion time with the following commands Command TIZ1x resets the inhibition time if input 1 is idle x is the setting parameter if O no reset if 1 reset Example How to reset inhibition time on input 1 TIZ11 Example How to disable the inhibition time reset function on input 1 TIZ10 Command 7 22 resets the inhibition time if input 2 is idle x is the setting parameter 12 futurel USER MANUAL TDG133 if O no reset if 1 reset Example How to reset inhibition time on input 2 TIZ21 Example How to disable the inhibition time reset function on input 2 TIZ20 Note 1 The default setting for this function is O To request the status of the reset function use command INI Note 2 The inhibition time is reset when following an alarm the input is back to idle w
26. spond to those described in this manual Important information The device must be installed in compliance with the current safety standards Supply the remote TDG133 only with stabilized DC tension between 9 and 32 V to be applied to the power plug see Picture 1 keeping in mind the polarity center po sitive USER MANUAL TDG133 Use a safety current limited power supply providing current of at least 500 mA able to cope with absorption peaks of 1 The power cable must not exceed 3 meters The relay outputs in the device can only be used to control low tension loads SELV type lt 60 Vdc The tension applied to the contacts of each relay must not exceed 60 Vdc The switching current on the relays must not exceed 10 A The maximum tension applied to the digital inputs is 32 The device can work in any position Check that the section of the cables used is enough The operating temperature of the device ranges between 10 C and 55 14 F 131 F f moisture condensation occurs wait for at least 2 hours before starting the equip ment Keep the device away from flower vases sinks water pipes etc Protect the device from moisture spray water and heat The device is meant for operation in clean and dry rooms Do not expose the device to heavy vibrations Do not use the device in presence of flammable gases vapors or dust The device can only be re
27. stored by disconnecting and reconnecting the power supply you will have three minutes to set up the device 11 Configuration SMS Commands and settings can be sent from any mobile via SMS as long as the message includes the password To speed up certain commands it is possible for the device to store 8 numbers enabled to send commands without the password in the device The numbers in this list are the same to which if enabled a few rings or alarm messages will be sent However there is a series of sensitive functions that no matter who sends the SMS require a password in particular functions that add or remove other numbers from the list that change the current password or request the list of approved numbers As a result of a command or query the device replies via an execution confirmation SMS or a SMS with information about the settings Please note that all commands that do not require a password are effective only if they come from a recognized phone that is a phone which number is in the list of those stored in the remote an outsider needs a password The remote accepts multiple SMS that is SMS with more than one command regarding one or more phone numbers commands must be separated by a comma Here we present and describe all commands that can be sent to the device via SMS Note every command must be written without spaces Command PWDxxxxx pwd changes the password xxxxx is the new password nu meric five
28. ter start up and without phone numbers stored in the list USER MANUAL TDG133 Power supply USB interface connector PWR optional center positive SIM card slot III III SMA female connector for GSM antenna Picture 1 0860 gt E GI 22 821190288 22218 13 TT LD1 LD2 LD3 LD4 C C NO NC NC NO OUT 1 OUT 2 IN1 IN2 8 Installing the USB A special USB interface code FT782M available separately must be installed on the remote control card as shown in the picture alongside the mini USB connector must be upwards 9 Start up You must first obtain a valid SIM Card from a GSM network provider Use a common mobile phone to disable the SIM Card PIN To do so check the manual of the mobile If the SIM Card PIN is not disabled the device cannot work as it cannot connect to the GSM network Before feeding the TDG133 please insert the SIM Card into the SIM Card holder mind the orientation making sure it is correctly blocked then connect the antenna cable to the connector Now connect the power supply futurel 7 ILX2192 USER MANUAL 10 Configuration The device can be set as follows EASY SETUP Configuration through call PROFESSIONAL SETUP Configuration through SMS Computer SETUP Configuration through PC connection it needs a USB interface code FT782M available separately 1 EASY SETUP Configuration through
29. ty perspective The phone costs related to sending SMS generated by the de vice are charged on the SIM in the device 2 Safety instructions In accordance with the current regulations on safety whenever using a device AN under tension all necessary precautions shall be taken The device must always be installed in absence of tension e The device must be placed into a suitable housing before use During the installation the device must not be connected to the power source or to other devices e Before handling the device or opening the container where it has been placed unplug the power connector and make sure the circuit is not live e Before working with any kind of tool on the device make sure it is disconnected from the power supply and that components that store energy capacitors are dischar ged e cables connected to the device particularly the power supply ones have to be checked regularly for fractures or damage of the isolation shield If cables are visibly future USER MANUAL damaged the device has to be switched off immediately until they have been repla ced Strictly comply with the technical specifications of components or modules used with this device If the information contained herein and or the information on the com ponents or modules used with the device are not clear enough please contact a qualified technician Before starting the device carefully check whether it is suitable for t
30. using the software Deabsw F Pata LIMTA FUTURA The software can be downloaded at Realm ps 13600 Comnet SSELETTRONICA a imas www futurashop it from the page of eb the TDG1 33 Medal iit d aon cancel IU Pes Humen Mariae In order to use the management software it is first necessary to install it Launch the Setup files and follow the installation instructions as they appear Once this is done start the program After this the window TDG Configurator appears on the screen through this window it is possible to modify all the settings of the device add users change the password etc It is an intuitive program and the graphic interface simplifies this LOG verti LOG emesa p ro ce d Uu re gt Chat Ma ezeun 18 USER MANUAL TDG133 So as to use the available commands supply and connect the TDG133 to the compu ter then select the communication port COM top left created If need be with the Update button you can update the list related to the available ports in the computer Afterwards press Connect to activate the connection and wait for the screen to update with all the data on the connected module From now on the TDG133 can be managed from you computer PC mode is shown by LD3 on If the device was connected to the computer before
Download Pdf Manuals
Related Search