FS-1020D - Kyocera
Contents
1. ma Pa USB Printer Rear Power Supply U J U Sunnan Before performing this step be sure to turn off both the printer and the com N puter s power switches and unplug the printer s power plug from the power Caution Outlet Failure to do so may result in electrical shock The standard Centronics parallel interface connector and USB interface connec tor are located on the rear of the printer Parallel Interface Connection 1 Plugoneendofthe printer cable not included into the parallelinterface con nector on the rear of the printer Use a parallel printer cable a that complies with the Note IEEE1284 standards e The printer will work best if it isinstalled nearthe computer The connecting cable should be shielded and not be longer than 3 meters 10 feet To printer ox 2 Close the clips on both sides to fix the connector in place er Plug the other end of the printer cable into the computer s Centronics paral lel interface connector ns USB Universal Serial Bus Interface Connection 1 Plug one end of the USB cable on the Ne A e The connecting cable should rear of the printer To printer be shielded and notbe longer USB Cable than 5 meters 16 feet e Use a cable that complies 2 with Revision 2 0 of USB stan Note dard a rectangular Type A p2. 3 Take the toner container from the bag lt gt Hold it with the protective seal orange p colored facing up Shake the toner con lH fA F tainer horizontally at least 5 times This LL Tha ensures that the toner is evenly distrib VO uted inside NASP 4 Carefully remove the protective seal 5 Installthe toner container into the printer 6 Push firmly on the top of the toner con tainer at the positions marked PUSH HERE 7 Pushthe lock lever to the lock LOCK position 8 Close the top cover To remove the toner container Pull the lock lever 1 to the release UNLOCK position pull the lock lever 2 then gently remove the toner con tainer Connecting the Printer to the Computer There are various ways of connecting the printer to the computer such as through the parallel interface connector throughthe USB Universal Serial Bus interface connec tor through the optional serial interface board kit IB 11 or through the optional net work interface board Printer Connections Network Optional Serial Interface Board kit IB 11 J Optional Network Interface Board DC 3 3V K N Serial Interface
3. 25cm 19 11 16 9 7 8 inches inches Environment Temperature 10 to 32 5 C 50 to 90 5 F ideally about 23 C 73 4 F Humidity 20 to 80 ideally 60 Do not install the printer where temperature or humidity is outside the rec ZW ommended range Print quality may suffer and there will be an increased Note chance of paper jams Places to Avoid Avoid installing the printer in locations subject to e Direct drafts of hot or cold air e Direct drafts from outside Avoid locations near building entrances e Sudden temperature or humidity changes e Sources of high temperature for example near stoves or radiators e Excessive dust e Vibration e Unstable surfaces and surfaces that are not level e Ammonia or other harmful fumes If you are planning to fumigate the room or make liberal use of insecticide remove the printer first e Excessive sunlight or humidity e Lack of ventilation e Low air pressure e g elevations greater than 2000 meters 6500 feet above sea level Before you can use the printer for the first time you must set up the printer by installing the toner container and interfacing with the computer 1 Open the printer top cover all the way 2 Confirm that the lock lever is in the ja release UNLOCK position If not pull it forward until it is in the release posi tion
4. PRECAUCION RADIACIONE LASER INVISIBLE CUANDO BE ABRE EVITAR EXPONERSE AL RAYO VAROI AVATTAESSA OLET ALTTIINA NAKYMATTOMALLE LASERS TEILYLLE ALA KATSO S TEESEEN Ki 2ODK OAB TERNAL YK MME ATOR DYKES SENEUEIELT HE id PURO AT INT MOA BHR YY Sa R L ESPOSIZIONE AL FASCIO MRAR ERENER CAUTION HOT SURFACE ACHTUNG HEISSE OBERFLACHE ATTENTION ATTENCION EXTERIOR CALIENTE ATTENZIONE p e De fey ame A DFA TEMPERATURE ELEVEE SUPERFICIE CHE SCOTIA Label inside the rear CDRH regulations The Center of Devices and Radiological Health CDRH of the U S Food and Drug Administration FS 1020D 220 240v 50 60Hz 3 8A KYOCERA MITA CORPORATION CLASS 1 LASER PRODUCT TO EC825 LASER KLASSE 1 NACH IEC825 KLASSE 1 LASER PRODUKT I H T 1EC825 LUOKAN 1 LASERLAITE CAUTION REMOVE POWER CORD BEFORE SERVICE AND FUSE REPLACEMENT VORSICHT VOR WARTUNG UND SICHERUNGS WECHSEL NETZSTECKER ZIEHEN ATTENTION POUR PREVENIR LES CHOCS ELECTRIQUES COUPER L ALIMENTATION AVANT DE REMPLACER LE FUSIBLE ATENCION DESENCHUFE EL CORDON DE ALIMENTACION ANTES DEL SERVICIO Y DEL REEMPLAZO DEL FUSIBLE PRECAUZIONE PRIMA DI CAMBIARE FIESIBILI O DI ESEGUIRE RIPARAZIONI STACCATE IL CADO DI ALIMENTAZIONE DESIGNED IN JAPAN ASSEMBLED IN CHINA gt ABS lt ACND03852444 Label inside the printer Laser radiation warning
5. Printed in China 7KKTB11E AX 2FM80010A 2003 9
6. FS 1020D 120x 60Hz 7 1A KYOCERA MITA CORPORATION TAMAKI PLANT 704 19 NOJINO TAMAKI TOWN WATARAI COUNTY MIE PREF JAPAN MANUFACTURED C11 THIS LASER PRODUCT CONFORMS TO THE APPLICABLE REQUIREMENTS OF FEDERAL REGULATIONS 21 CFR lowest CHAPTER 1 SUBCHAPTER J 3468 UL 1950 p US LISTED ested To Comply vinree FOR HOME OR OFFICE USE This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada CAUTION REMOVE POWER CORD BEFORE SERVICE AND FUSE REPLACEMENT ATTENTION POUR PREVENIR LES CHOCS ELECTRIQUES COUPER L ALIMENTATION AVANT DE REMPLACER LE FUSIBLE PRECAUZIONE PRIMA DI CAMBIARE FIESIBILI O DI ESEGUIRE RIPARAZIONI STACCATE IL CADO DI ALIMENTAZIONE DESIGNED IN JAPAN ASSEMBLED IN OHNA ABSC European Asian Pacific countries U S A Canada Label on the printer s rear panel implemented regulations for laser products on August 2 1976 These regulations apply to laser products manufactured after August 1 1976 Compliance is mandatory for products marketed in the United States A label indicating compliance with the CDRH regulations mus
7. is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the manufacturer for compliance could void the user s authority to operate the equipment Shielded circular cable should be used for interfacing with the computer E Caution to user Any modification without prior permission may cause harmful interference If any modification change is introduced to this eguipment without prior permission Kyocera Mita as the manufacturer cannot guarantee compliance with FCC rules To use eguipment which does not comply with FCC rules is prohibited The printer may be optionally installed with the following units W Options Conforming to the Class B limits e IB 11 Serial Interface Board Kit e IB 20 IB 21E 22 Network Interface Card e PF 17 Paper Feeder 250 sheets Important note on the interface connectors Be sure to turn off printer power before connecting or disconnecting an interface cable to the printer For protection against static discharge which may be applied to the printer s internal electronics through the interface connector s keep any interface connector which is not in
8. the paper cassette all the way out of the printer 3 Open the duplexer s rear cover and remove any jammed paper Duplexer s Rear Cover 4 Open the duplexer s front cover and remove any jammed paper Duplexer s Front Cover 19 Jam Inside the Printer 1 Open the printer s top cover 2 Openthe printer s front cover 3 Lift the process unit together with the toner container out of the printer 4 Remove the jammed paper When pulling the paper pull Pi gently so as not to tear it Torn Note pieces of paper are difficult to remove and may be easily over looked preventing recovery from the jam 5 Replacethe process unit and toner con tainer then close the printer 20 Jam at the MP Tray 1 Leaving any paper that may be jammed there remove the rest of the paper from the MP tray Do nottry to forcefully pull out paper that has already been fed partially in to the MP tray Instead proceed to the next step 2 Open the printer s top cover 3 Open the printer s front cover Front Cover 21 A Registration Roller metal B Registration Roller metal 22 4 Lift the process unit together with the ton
9. use capped using the protective cap supplied Note Use shielded interface cable Safety information W Laser safety This printer is certified as a Class 1 laser product under the U S Department of Health and Human Services DHHS Radiation Performance Standard according to Radiation Control for Health and Safety Act of 1968 This means that the printer does not produce hazardous laser radiation Since radiation emitted inside the printer is completely confined within protective housings and external covers the laser beam cannot escape from the printer during any phase of user operation W Laser notice This printer is certified in the U S to conform to the requirements of DHHS 21 CFR Subchapter for Class I 1 laser products and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 825 23 DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure W Caution labels VORSICHT EVITARE we Fet AU DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM ATTENTION RAYONNEMENT LASER INVISIBLE EN CAS D OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GE FFNET NICHT DEM STRAHL AUSSETZEN ATTENZIONE RADIAZIONE LASER INVISIBILE IN CASO DI APERTURA
10. CL and PJL are registered trademarks of Hewlett Packard Company Centron ics is a trade name of Centronics Data Computer Corp PostScript is a registered trademark of Adobe Systems Incorporated Adobe and Acrobat are trademarks of Adobe Systems Incorpo rated ENERGY STAR is a U S registered mark All other brand and product names are registered trademarks or trademarks of their respective companies This Kyocera Mita page printer uses PeerlessPrintXL to provide the HP LaserJet compatible PCL 6 language emulation PeerlessPrintXL is a trademark of The Peerless Group Redondo Beach CA 90278 U S A This product was developed using the Tornado Real Time Operating System and Tools from Wind River Systems AGFA This product contains UFST and MicroType fonts from Agfa Corporation IBM PROGRAM LICENSE AGREEMENT THE DEVICE YOU HAVE PURCHASED CONTAINS ONE OR MORE SOFTWARE PROGRAMS PROGRAMS WHICH BELONG TO INTERNATIONAL BUSINESS MACHINES CORPORA TION IBM THIS DOCUMENT DEFINES THE TERMS AND CONDITIONS UNDER WHICH THE SOFTWARE IS BEING LICENSED TO YOU BY IBM IF YOU DO NOT AGREE WITH THE TERMS AND CONDITIONS OF THIS LICENSE THEN WITHIN 14 DAYS AFTER YOUR ACQUISITION OF THE DEVICE YOU MAY RETURN THE DEVICE FOR A FULL REFUND IF YOU DO NOT SO RETURN THE DEVICE WITHIN THE 14 DAYS THEN YOU WILL BE ASSUMED TO HAVE AGREED TO THESE TERMS AND CONDITIONS The Programs are licensed not sold IBM or the applicable IBM country organization gr
11. E Ifthe product has been dropped or the cabinet has been damaged Canadian Department of Communications compliance statement This Class B digital apparatus complies with Canadian ICES 003 Avis de conformit aux normes du ministere des Communications du Canada Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada ISO 7779 Maschinenl rminformationsverordnung 3 GSGV 18 01 1991 Der h chste Schalldruckpegel betr gt 70 dB A oder weniger gem ISO 7779 25 CE Marking Directive according to Council Directive 89 336 EEC and 73 23 EEC Manufacturer s name Kyocera Mita Corporation Tamaki Plant Manufacturer s address 704 19 Nojino Tamaki Cho Watarai Gun Mie Ken 519 0497 Japan declares that the product Product name Page Printer Model number FS 1020D as tested with the enhancement optional unit PF 17 and IB 21E conforms to the following product specifications EN 55 022 1998 Class B EN 61 000 3 2 1995 EN 61 000 3 3 1995 EN 55 024 1998 EN 60 950 1992 A1 A2 A3 A4 A11 EN 60 825 1 1994 A11 The manufacturer and its merchandising companies retain the following technical documentation in anticipation of the inspection that may be conducted by the authorities concerned User s instruction that conforms to the applicable specifications Technical drawings Descriptions of the procedures that guarantee the conformity Other technical information Declaration of Conformity Australia Manu
12. G AND DISTRIBUTION FOR ALDC 29 3 Limitation of Remedies IBM s entire liability under this license is the following 1 For any claim including fundamental breach in any form related in any way to this license IBM s liability will be for actual damages only and will be limited to the greater of a the equivalent of U S 25 000 in your local currency or b IBM s then generally available license fee for the Program This limitation will not apply to claims for bodily injury or damages to real or tangible personal property for which IBM is legally liable IBM will not be liable for any lost profits lost savings or any incidental damages or other economic consequential damages even if IBM or its authorized supplier has been advised of the possibility of such damages IBM will not be liable for any damages claimed by you based on any third party claim This limitation of remedies also applies to any developer of Programs supplied to IBM IBM s and the developer s limitations of remedies are not cumulative Such developer is an intended ben eficiary of this Section Some jurisdictions do not allow these limitations or exclusions so they may not apply to you 4 General You may terminate your license at any time IBM may terminate your license if you fail to comply with the terms and conditions of this license In either event you must destroy all your copies of the Program You are responsible for payment of any taxes including personal
13. W KYOCERA FS 1020D Page Printer Ecosrs Installation Guide Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION Notice on Software SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER S EMULATION MODE The printer is factory set to emulate the HP PCL 6 The emulation mode can be changed by following the procedures described in the Operation Guide contained as an electronic file in the Kyocera Mita Document Library CD ROM supplied with the printer Notice The information in this manual is subject to change without notification Additional pages may be inserted in future editions The user is asked to excuse any technical inaccuracies or typographical errors in the present edition No responsibility is assumed if accidents occur while the user is following the instructions in this manual No responsibility is assumed for defects in the printer s firmware contents of its read only memory This manual any copyrightable subject matter sold or provided with or in connection with the sale of the page printer are protected by copyright All rights are reserved Copying or other reproduc tion of all or part of this manual any copyrightable subject matter without the prior written consent of Kyocera Corporation is prohibited Any copies made of all or part of this manual any copyrightable subject must contain the same copyright notice as the material from which the copy ing is done KN Table of Co
14. ants you a license for the Programs only in the country where you acquired the Programs You obtain no rights other than those granted you under this license The term Programs means the original and all whole or partial copies of it including modified cop ies or portions merged into other programs IBM retains title to the Programs IBM owns or has licensed from the owner copyrights in the Programs 1 License Under this license you may use the Programs only with the device on which they are installed and transfer possession of the Programs and the device to another party If you transfer the Programs you must transfer a copy of this license and any other documentation to the other party Your license is then terminated The other party agrees to these terms and con ditions by its first use of the Program You may not 1 use copy modify merge or transfer copies of the Program except as provided in this license 2 reverse assemble or reverse compile the Program or 3 sublicense rent lease or assign the Program 2 Limited Warranty The Programs are provided AS IS THERE ARE NO OTHER WARRANTIES COVERING THE PROGRAMS OR CONDITIONS EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not allow the exclusion of implied warranties so the above exclusion may not apply to you SUPPLEMENT TO AGREEMENT FOR SOFTWARE BUNDLIN
15. er container out of the printer Use the following procedure that corre sponds to the status of the jammed paper in order to remove that paper A If the leading edge of the jammed paper has been fed further into the printer than the metal registration roller remove the jammed paper by its leading edge B Ifthe paper has not been fed as far as the metal registration roller remove the jammed paper from the MP tray side FCC statement for users in the United States This device complies with Part 15 of the FCC Rules Operation is subject to the following two con ditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation W Note This eguipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful inter ference to radio or television reception which can be determined by turning the equipment off and on the user
16. facturer s name Kyocera Mita Corporation Tamaki Plant Manufacturer s address 704 19 Nojino Tamaki Cho Watarai Gun Mie Ken 519 0497 Japan declares that the product Product name Page Printer Model number FS 1020D as tested with the enhancement optional unit PF 17 and IB 21E Description of device The model FS 1020D is a 20 ppm A4 size plain paper supporting page printer utilizing laser dry toner etc The printer can be eguipped with the optional paper feeder model PF 17 Conforms to the following product specifications AS NZS 3548 1995 EN 55 022 1998 Class B IEC 60950 EN 60 950 1992 A1 A2 A3 A4 A11 IEC 60825 1 EN 60 825 1 1994 A11 The manufacturer and its merchandising companies retain the following technical documentation in anticipation of the inspection that may be conducted by the authorities concerned User s instruction that conforms to the applicable specifications Technical drawings Descriptions of the procedures that guarantee the conformity Other technical information Kyocera Mita Australia Pty Ltd 6 10 Talavera Road North Ryde NSW 2113 Australia Phone 61 2 9888 9999 Fax 61 2 9888 9588 26 Declaration of Conformity U S A Model Number Page Printer FS 1020D as tested with enhancement optional units PF 17 IB 21E Trade Name Kyocera Mita Responsible Party Kyocera Mita America Inc Address 225 Sand Road PO Box 40008 Fairfield New Jersey 07004 0008 U S A Telephone numbe
17. he opposite direction to counter act the curl Printed sheets will then come out flat Correct Incorrect 15 16 Envelopes Envelopes should be fed in the face up position right edge first Test a sample envelope on the printer and check that printing quality is sat ZW isfactory before purchasing Note 1 111 Jj le Some types of envelopes are not suit able for printing For details on suit able types of envelopes see the Operation Guide contained as an elec tronic file in the CD ROM supplied with the printer To close the MP tray Close the flap on the subtray then push in the subtray and close the MP tray Be careful not to push the tray back into the printer with the subtray folded out horizon tally as shown in the figure Printing a Status Page To test the printer print a status page indicating factory settings 1 Turn on the printer s power switch Upon turning on the power the printer s 4 indicators flash in sequence until printer initialization is complete then the indicator on line lights steadily If the indicator does not light Pi check that previous steps were Note performed properly If you install the toner container and turn on the power after a moment the indicators light in sequence from top to bottom When the printer is first switched on after tone
18. lug and a sguare Type B plug 2 Plugtheotherendofthe USB cable into the computer s USB interface connec tor Connecting the Power Cord This section describes the procedure for connecting the power cable and various cautions Notes on Power Supply e Install the printer near an AC wall outlet preferably one that can be used for the printer alone e Onlyusethis printer with the supply voltage indicated on the serial number label attached to the printer s rear panel e Ifan extension cord is used the totallength of the power cord plus extension should be 5 meters 16 feet or less Power Reguirements Voltage 110 V 120 V 220 to 240 V 10 at each voltage Freguency 60 Hz 110 V 120 V 2 50 60 Hz 220 to 240 V 2 Current capacity Max 6 5 A at 110 V max 7 1 A at 120 V or max 3 8 A at 220 to 240 V To Connect the Power Cord 2 e Be sure the printer s power switch is turned off e Only use the power cord supplied with the printer Caution 1 Plug the power cord into the power cord connector on the rear of the printer Power Cord 2 Connect the other end of the power cord into a power outlet Be sure to connect to a 3 wire g grounded power strip Warning Adding Paper to the Paper Cassette and MP Tray The paper cassette can accommodate A5 to Legal size paper and can hold approxi mately 250 sheets The Multi Purposetray can accommodate the various paper sizes and can h
19. ntents STEP T Un Packing ui sesescnccdetcedcisccasccacduausdedeaediveneecetenetctenssdaveeseste 1 STEP 2 Positioning the Printe cscccccccceeceeeesssesssesseseeeeeees 3 STEP 3 Installing the Toner Containel 0cccssseeseeseeseeeeeees 4 STEP 4 Connecting the Printer to the Compute cccccsss 7 STEP 5 Connecting the Power Cord cccccccccccceesssseeseseesseeeeeees 9 STEP 6 Adding Paper to the Paper Cassette and MP Tray 70 STEP 7 Printing a Status Page ccscccseceeeeeeeeessseeseneeneeeeees 17 2003 by KYOCERA MITA CORPORATION All rights reserved Revision 1 0 September 2003 Unpacking Carefully remove the printer and other items from the box Check that nothing is miss ing against the list of shipped components below List of Shipped Components Printer lt I Cleaning Cloth A Power Cord D CD ROMs A Installation Guide this booklet A T Extension Tray C for U S A only Removing Shipping Material Remove the tape on the rear side of the printer and remove the protective packing from the paper cassette Positioning the Printer Make sure that the place of installation meets the following requirements Clearance ASIN around the printer Prolonged 40 cm Warning Use without sufficient clearance 15 3 4 may cause heat to build up inches GZ Be sure to secure enough space F within the printer resulting in fire
20. old approximately 50 sheets of paper The following paper weights can be used with the printer Paper source Paper weight Paper cassette 60 to 105 g m MP tray 60 to 163 g m The edges of paper are sharp When loading paper be careful not to cut your hand on the paper Caution Paper cassette Standard paper sizes are attached to the inside of the paper cassette as shown in the following figure Align the paper guides and paper stopper to the paper size you want to print on as described on the next page Oficiol 10 Release Button Paper Guide Pull the paper cassette all the way out of the printer Adjust the position of the paper stopper located at the rear of the paper cassette Press in the release button and slide the stopper to the desired paper size When shipped from the factory the paper cas sette is set to either A4 or Letter size In order to load either Folio or Oficio II size paper into the Note paper cassette refer to Adjust ing the paper stopper for Folio and Oficio II sizes on page 14 and adjust the paper stopper Adjust the position of the paper guides located on the left and right sides of the paper cassette Press in the release but ton on the left side guide and slide to the desired
21. ommend you consult with your dealer about the additional actions you should take to avoid possible damages that may occur when the printer is used next time W Moving the Printer When you move the printer e Move it gently e Keep it as level as possible to avoid spilling toner inside the printer as shown in the figure e Ifyou ship the printer remove and ship the process unit separately Pack the process unit in a plastic bag and ship them separate from the printer itself Be sure to consult a serviceman before attempting long distance transportation of the printer 27 ENERGY STAR VIA As an ENERGY STAR Partner we have determined that this product meets the ENERGY STAR guidelines for energy efficiency The basic objective of the ENERGY STAR Program is to reduce environmental pollution by encouraging the manufacture and sale of eguipment that uses energy more efficiently This printer is eguipped with a sleep timer function that conforms with the stan dards of the ENERGY STAR Program This function makes it possible to reduce the amount of electrical power consumed by the printer For maximum power savings turn off the printer s power supply when not using the printer for extended periods of time For details on the sleep timer function and printer power consumption refer to the CD ROM instruction manual provided with the printer Initial settings of the sleep timer function and power saved using the sleep timer functi
22. on Initial sleep mode setting Power consumption in sleep mode 5 minutes 15 minutes 4 3 W 20 W 220 to 240 V 50 Hz 60 Hz 4 4 W 20 W 110 V 60 Hz 4 5 W 20 W 120 V 60 Hz ENERGY STAR program guideline Group for Energy Efficient Appliances GEEA Y Options The goal of GEEA is efficient use of energy This product has a high effi ciency profile and meets the criteria for receiving the GEEA Label Initial sleep mode setting Power consumption in sleep mode 5 minutes 15 minutes 4 3 W 10 W 220 to 240 V 50 Hz 60 Hz 4 4 W 10 W 110 V 60 Hz 4 5 W 10 W 120 V 60 Hz GEEA criteria The following options are available for the printer Printer 28 Network Interface Card IB 20 21E 22 Enables printing from multiple com g puters via a network Serial Interface Board Kit IB 11 Le Connect to the computer s serial printer port with a serial cable Network Interface Card Paper Feeder PF 17 3 3 V DC P Pran or 2 Holds approximately 250 sheets of A5 Serial Interface Board to Legal size paper Kit IB 11 Other Options Memory DIMM CompactFlash card See your dealer for purchasing informa Paper feeder tion ofthese optional devices that are best PF 17 suited for use with this printer Regarding Tradenames KPDL and KIR Kyocera Image Refinement are trademarks of Kyocera Corporation Hewlett Packard P
23. paper size When using custom size paper move the paper guides and paper stopper all the way out insert the paper then adjust the paper guides and paper stopper to the size of the paper Adjust them so that they are in light contact with the paper The printer does not automati ZT cally detect the size of the paper Note loaded into the paper cassette or MP tray As a result when ever you load paper having a different size you must adjust the paper size For details refer to the Operation Guide contained as an electronic file in the CD ROM supplied with the printer 17 Caution Fan the media paper transpar encies then tap it on a level surface to avoid media jams or skewed printing 4 Slide the paper into the paper cassette Donotload more paperthan will fit under the load limits on the top of the paper guides the paper cassette will hold approx imately 250 sheets of paper with a 80 g m 21 Ib basis weight or with a thickness of 110 microns 5 Insertthepapercassetteinto the slotin the printer Push it straight in as far as it will go To use large size paper Be sure to open the paper stopper when printing onto A4 or Letter size paper Paper Stopper When printing onto paper of a size larger than A4 or Letter be sure to Subtray open the paper stopper and then open the subtray as well When printing onto Legal size paper install the extension tray that i
24. property taxes resulting from this license Neither party may bring an action regardless of form more than two years after the cause of action arose If you acquired the Program in the United States this license is governed by the laws of the State of New York If you acquired the Program in Canada this license is gov erned by the laws of the Province of Ontario Otherwise this license is governed by the laws of the country in which you acquired the Program 30 This page intentionally left blank This page intentionally left blank OUALITY CERTIFICATE This machine has passed all guality controls and final inspection bW Operating Keys and Indicators For details on operating procedures see the F S 1020D Operation Guide contained as an electronic file in the CD ROM supplied with the printer O o 1 Number Name Function o 2 1 Ready indicator Indicates whether the printer is on line or 88 o 3 off line 81 Oo 4 2 Data indicator Indicates that the printer is receiving data 6 5 3 Attention indicator Indicates whether the paper cassette is NSA empty or a paper jam has occurred 4 Toner indicator Indicates when toner is low or when toner 6 is exhausted Operator Panel 5 Cancel key Abandons a printing job 6 Go key e Switches the printer on line and off line e When pressed for 3 or more seconds prints a user status page e Prints and feeds out one page
25. r 973 808 8444 Fax number 973 882 6000 Manufacturer s name Kyocera Mita Corporation Tamaki Plant Manufacturer s address 704 19 Nojino Tamaki Cho Watarai Gun Mie Ken 519 0497 Japan This device complies with Part 15 of the FCC Rules Operation is subject to the following two con ditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The manufacturer and its merchandising companies retain the following technical documentation in anticipation of the inspection that may be conducted by the authorities concerned User s instruction that conforms to the applicable specifications Technical drawings Descriptions of the procedures that guarantee the conformity Other technical information Kyocera Mita America Inc Disclaimer We shall have no liability or responsibility to customers or any other person or entity with respect to any liability loss or damage caused or alleged to be caused directly or indirectly by eguipment sold or furnished by us including but not limited to any interruption of service loss of business or anticipatory profits or conseguential damages resulting from the use or operation of the eguipment or software Prolonged Non Use and Moving the Printer W Prolonged Non use If you ever leave the printer unused for a long period of time remove the power cord from the wall outlet We rec
26. r installa tion there will be a delay of approximately 15 minutes before the printer gets ready to print Once the indicator lights printer installation is complete 2 The printer can print two different types of status page standard and service purpose A service purpose sta tus page contains more detailed infor mation about printer settings than a standard status page e To printa standard status page press the key for at least 3 seconds and the indicators light in seguence from top to bottom e To print a service purpose status page press the key for more than 10 seconds and the indicators light in seguence twice from top to bottom If the status page prints correctly printer setup is complete For details on using the printer refer to the Oper ation Guide contained as an electronic file in the CD ROM supplied with the printer 17 18 Correcting a Paper Jam If a paper jam occurs while you are printing remove the jammed paper as described below After you have removed the jammed paper open and close the top cover once Jam at the Face down Tray and the Rear Cover Open the rear cover and remove the jammed paper as shown in the figure Rear Cover Jam at the Paper Cassette Pull out the paper cassette and remove the jammed paper Paper Cassette Jam at the Duplexer 1 Open the rear cover and remove the jammed paper as shown in the figure Rear Cover 2 Pull
27. s included with your printer onto the paper stopper The extension tray is supplied for U S A only 13 14 Adjusting the paper stopper for Folio and Oficio II sizes Perform the following procedure in order to adjust the paper stopper when loading Folio and Oficio II size paper into the paper cassette 1 Remove the stopper extension lock from the paper stopper Stopper Extension Lock 2 Slide the paper stopper back until the edge of the cut out portions 1 of the paper stopper are aligned with the back edge of the paper cassette 3 Insert the stopper extension lock into the holes in the paper stopper 4 Tosecure the stopper extension lock in place press down on the lock and slide the paper stopper back slightly The paper stopper will be fixed in place for Folio and Oficio II size paper Multi Purpose MP tray 1 Pull the MP tray towards you until it stops 2 Pullout the subtray and unfold the flap 3 Adjust the position of the paper guides on the MP tray Standard paper sizes are attached to the MP tray For stan dard paper sizes slide the guides to the position marked correspondingly e Do not load more paper than will fit under the load limits on Note the inside of the MP tray If the paper is considerably curled in one direction for example if the paper is already printed on one side try to roll the paper in t
28. t be attached to laser products marketed in the United States Ozone concentration The printers generate ozone gas Og which may concentrate in the place of installation and cause an unpleasant smell To minimize concentration of ozone gas to less than 0 1 ppm we recommend you not to install the printer in a confined area where ventilation is blocked 24 IMPORTANT SAFEGUARDS 1 Readallofthese instructions and save these instructions for later use Unplug this product from the wall outlet before cleaning Do not use this product near water Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product 5 Slots and openings in the cabinet and the back are provided for ventilation to ensure reliable oper ation of the product and to protect it from overheating these openings must not be blocked or cov ered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation unless proper ventilation is provided 6 This product is equipped with a 3 wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature Ifyou are unable to insert the plug into the outlet contact your electrician to replace your obsolete ou
29. tlet Do not defeat the purpose of the grounding type plug Pwr 7 Donotallow anything to rest on the power cord Do not locate this product where persons will walk on the cord 8 Ifan extension cord is used with this product make sure that the total of the ampere ratings on the products plugged into the extension cord do not exceed the extension cord ampere rating 9 Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in arisk offire or electric shock Never spill liquid of any kind on the product 10 Except as explained elsewhere in User s Manual do not attempt to service this product yourself Removing covers may expose you to dangerous voltage points or other risks Refer all servicing in those compartments to service personnel 11 Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions A When the power cord or plug is damaged or frayed B Ifliquid has been spilled into the product C Ifthe product has been exposed to rain or water D Ifthe product does not operate normally when the operating instructions are followed Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation
Download Pdf Manuals
Related Search