Home

[PDF:1.8MB]

1. ICD gu UNIVERSAL SERIAL BUS D ZLECEM Ooppopet Wireless Optical Mouse M NE2DR Series User s Manual Thank you for purchasing the ELECOM M NE2DR Series wireless optical mouse This manual describes the operating instructions and safety precautions for using the M NE2DR Series Ensure that you have read this manual before using the product After reading this manual store it somewhere safe for future reference Except in certain cases the M NE2DR Series is referred to as this product in this manual Safety Precautions E Meaning of symbols Failure to observe precautions may result in serious personal injury or death due to N WARNING y p muy fire electric shock or other causes Failure to observe precautions may result in personal injury due to electric shock or CAUTION p T piy other causes and may damage other equipment S Prohibited action Mandatory action Q Situation that needs attention Na Notes and reference information Information that is handy to know Observe these precautions carefully to avoid personal injury damage fire and other problems N WARNING n If a foreign object water metal chip etc enters the product immediately stop using the product and disconnect the receiver unit from the PC and remove the battery from the mouse If you continue to use the product under these conditions it may cause a fire or electric shock If
2. Illuminates red when the mouse body is turned on When the mouse body is moved this sensor detects mouse movement Avoid looking directly at the light of the sensor as doing so may cause eye damage Battery cover This cover is removed to install batteries Battery housing Batteries are inserted here USB connector Male Connected to a PC USB port Receiver unit cap A removable silicon cap You can adjust the orientation of the cap to match the orientation of the PC s USB port Vary the style depending on which colour you buy EN aC EKO amp ae E Removing the cap When removing the cap from the receiver unit hold both the cap and the connector and pull out in a straight manner When removing the receiver unit from the USB port the cap may come off If this happens remove the separated receiver unit by itself QD Preparation before Use Installing Replacing the Battery Before using this product install one AAA battery in the mouse body 1 Remove the battery cover 2 Insert the battery Y e Make sure that the polarity is correct 3 Install the battery cover as before E Replacing battery 1 Remove the battery cover 2 Remove the battery 3 Insert the battery 4 Install the battery cover as before When using Windows Steo Check USB ports Check the USB port on your computer USB port Y e Any USB port may be used e This product
3. Cleaning the Mouse If the product body becomes dirty wipe it with a soft dry cloth Y Use of a volatile liquid paint thinner benzene alcohol etc may affect the material quality and colour of the product Cautions for Wireless Equipment This product is wireless equipment using the entire range 2 4FH1 of the 2 4 GHz band and it is possible to avoid the band of HEHE iz mobile object identification systems FH SS is used for the radio wave method The interference distance is 10 m The 2 4 GHz band is also used by medical equipment Bluetooth and wireless LAN equipment conforming to the IEEE802 1 1b 11g 11n standard e Before using this product check that there are no other radio stations operating nearby e f electromagnetic interference occurs between this product and other radio stations move this product to another location or stop using this product Other radio stations refer to industrial scientific and medical devices using the 2 4 GHz band like this product other radio stations of this type licensed radio station premises for mobile object identification system that is used in factory production lines certain non licensed low power radio stations and amateur radio stations WARNING S e Do not use this product with a device that may have a serious function or influence There are rare cases where an external radio wave at the same frequency or the radio wave emitted fro
4. an abnormality is found with this product emission of heat smoke or abnormal smell from the product immediately stop using the product shutdown the PC and after thoroughly checking that heat from the product will not cause burns disconnect the receiver unit from the PC and remove the battery from the mouse After doing this contact the retailer from whom you purchased the product Do not drop or hit this product If this product is damaged immediately stop using the product and disconnect the receiver unit from the PC and remove the battery from the mouse If you continue to use the product under these conditions it may cause a fire or electric shock Do not attempt to disassemble modify or repair this product by yourself as this may cause a fire electric shock or product damage 9200 Do not put this product in fire as the product may burst resulting in a fire or injury Do not connect or disconnect the receiver unit with a wet hand modify the receiver unit or bend it forcibly as this may cause a fire or electric shock The receiver unit contains small parts that could be swallowed by a child Ensure that the unit is stored in an area where it is not accessible to children NCAUTION Do not place this product in any of the following environments S e In a car exposed to sunlight a place exposed to direct sunlight or a place that becomes hot around a heater etc e In a moist place or
5. EA X RNASE EMR2SABZPENR HAMA POS SBY S T 11363 2006 I ERIR EER Adobe Reader 9 to the receiver unit until operation stabilises Gaerne gt Interference may occur if multiple units of this product are used The r mouse is operating normally if the screen together or if this product is used with other wireless devices moves up and down as you scroll the wheel l In such case move the mouse closer to the receiver unit until D e Carefully check the orientation of the connector and the place where you will connect the receiver unit e If you feel strong resistance when inserting the receiver unit check that the shape and orientation eye ey of the connector is correct Using excessive force D In applications that do not support scrolling the operation stabilises C may damage the connector and cause injury screen will not move when you scroll the wheel Multiple units of this product have an automatic channel l e When removing the receiver unit from the USB avoidance function The device complies with Part 15 of the FCC Rules Operation is subject port the cap may come off If this happens gt Operation becomes unstable when battery power is low See to the following two conditions 1 this device may not cause harmful remove the separated receiver unit by itself E Disconnectin
6. Magnetic substance e g metal desk Approx 3 m Fe REL URE Ak ETEKINAREN of the USB hub a j Test values in the ELECOM environment OnE E OEA AATA D2 Display your favourite web site in Safari and change the operation stabilises even after you have deleted the driver E c00 W x875 0 x380 Himm BANA LR ante gt MSCS ART RET size of the window so that the vertical scrollbars appear gt It is possible that the receiver unit is not connected correctly to following the instructions below it is possible caer a F W T D TT TE HOARE gt FECES REN E IARR i The sample website used here is the ELECOM homepage the USB port Disconnect the receiver unit from the USB port and that there is something wrong with the PC When the cap ig removed Za FAS GES BLS ELSE Re ae FG FR EF Bz ooo ra sasae reconnect it Contact the PC manufacturer Operating temperature 5 to 40 C 90 RH max no condensation PETHE i i gt The receiver unit and the mouse body are too far apart or there idi 1 Activate the Macintosh ibility that th it ip ae fe tont With the receiver unit connected to the PC follow the May a e Wait until Mac OS X has started up completely IS 3 paa lity tha us ae unit Is amg ina ine lon trom procedure below to remove the unknown device oring Revove tuley 10 to 60 C 90 RH max no condensation which it cannot receive radio signals Adjust the position of the Be sure to log on using an administrator account when aaah l 2 Insert the r
7. Manager and then repeat Step 2 Installing the Mac OS X 10 5 to 10 5 8 10 6 to 10 6 7 FO on aa UZ in Safari gt It is possible that the reflectivity of the surface on which this Receiver Unit on the front of this sheet Resolution dpi 1000 i ae i i i i i rface USB Click the Safari icon in the Dock tui product is being used is not suitable for an optical mouse 7 3 Inte ee pe ees USB port 7 fa inek gt Use this product on a mouse pad that is designed for use with Y e If there are multiple unknown devices before Radio frequency 2 4 GHz bandwidth e U IKE EMR Safari will launch l removing a device check that it is actually this ATA optical mice i j Radio wave method FH SS modulation E E ET RTT gt AF west ii FH ie A B b d Pen product Disconnect the receiver unit and check SEE jen deb RAMS SZ RR EE BS gt FERRGT AT gt Reacts aN O e Any USB port may be used O If Safari is not in the Dock double When using this product on a metallic surface such as a steel which unknown device disappears The device Radio wave outreac Non magnetic substance e g wooden desk Approx E REISS lt ACCA SS EE oe BE o e This product can be connected to a USB hub ASSIS it click the Safari icon in the Applications desk radio wave outreach may be shortened In such cases that disapoearsits this product 10m DUE may not work depending on the power supply capability folder i ip aca ties HSI Ee aeri She CURS ana Ease ine ankron dece dees Mota cappenr
8. a place where condensation may occur In an uneven place or a place exposed to vibration e In a place where a magnetic field is generated near a magnet etc e In a dusty place This product does not have a waterproof structure Use and store this product in a place where the product body will not be splashed with water or other liquid Rain water mist juice coffee steam or sweat may also cause product damage Y e Do not use this product with any device that may significantly affect other equipment in the event that it malfunctions e If this product is used on a transparent surface such as glass or a highly reflective surface such as a mirror the optical sensor will not function correctly and mouse cursor movement will become unstable e When not using the mouse for one month or more disconnect the receiver unit from the PC e When you no longer need to use this product be sure to dispose of it in accordance with the local ordinances and laws of your area e Avoid looking directly at the light of the sensor as doing so may cause eye damage e Always keep the receiver unit out of the reach of children as there is a danger that they may swallow it E Batteries CAUTION Use AAA alkaline batteries AAA manganese batteries or AAA nickel hydride storage batteries with this product If this product will be unused for a long period of time remove the battery to avoid battery leakage and failure E
9. can be connected to a USB hub However it may not work depending on the power supply capability of the USB hub Step2 Installing the Receiver Unit 1 Activate the PC e If Windows prompts you to choose an account a user name when it starts up be sure to log on using an administrator account e Wait until Windows has started up completely 2 Insert the receiver unit into the USB port of the PC Insert here Ca USB port Ro N Y e Carefully check the orientation of the connector and the place where you will connect the receiver unit e If you feel strong resistance when inserting the receiver unit check that the shape and orientation of the connector is correct Using excessive force may damage the connector and cause injury e When removing the receiver unit from the USB port the cap may come off If this happens remove the separated receiver unit by itself 3 The mouse driver is installed automatically Turning On and Off the Mouse E Turning on the mouse When using this product turn the mouse body poweron Slide the power switch to the ON position Qs a u amp Z E Turning off the mouse When not using this product turn the mouse body off to save battery power Slide the power switch to the OFF position Ot O T T Z E Restoring from sleep state Click the right mouse button To reduce battery drain the mouse enters sleep mode automatically if it is lef
10. eceiver unit into a USB port on your Macintosh receiver unit Windows starts up Batteries AAA alkaline battery AAA manganese battery AAA ee eee a ingen Here The operable range of this Screen display may differ depending on operating nickel hydride storage battery Ta i product is the area within a system but the procedure remains the same Operating time Measure of the operating time when an AAA alkaline M NE2DR Wit battery is used 1 Display Device Manager Continuous operating time Approx 69 hours F RRE from the receiver unit eno ELECOM WEB SITE Approximately Continuous standby time Approx 75 days i ime EAB E S KN STREAK Zi Sige sca acne ea Nea E Depending on the usage reyes cr VI E ae 10m 1 From the Start menu right click Computer Estimated serviceable time Approx 31 days environment the mouse may ee i omnes JOmed oo ole fe Lo 0 not operate even when it is and 25 of the PC operation is assigned to mouse omm Oo Oo oO Oo oO 6 circle with a radius of 10 m 3 Scroll the wheel back and forth e Windows 7 and Windows Vista GB vo os Receiver unit esy within approximately 10 m a re operation aR RRR BBA AT EUR REED AIS EEE SJ T 11363 2006 i Magnifier VN l E gt o of the receiver unit In such J eie M
11. erally trademarks or registered trademarks TEL 65 6347 7747 FAX 65 6753 1791 2011 ELECOM Co Ltd All Rights Reserved EMB21 M11 Confirm Device Removal 5 Repeat the procedure from Step 2 Installing the Receiver Unit on the front of this sheet
12. face device If it is detected as an unknown device see Removing an unknown device and after removing the device from Device Manager repeat Step 2 Installing the Receiver Unit Set Program Access and Map Network Drive Defaults Disconnect Network Drive generates uses and can radiated radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communication However there is no grantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by tuning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures amp 2 Printers and Faxes Help and Support 4 Click e System Properties Stem Restore _ _ Atonement _ Remote Reorient or relocate the receiving antenna on the front of this sheet D Genemi Compter Neme Hoover Asvon M Increase the separation between the equipment and receiver gt If you have installed drivers and settings utilities produced by the pon gra Se Connect the equipment into an outlet on a circuit different from that original manufacturer for a previous mouse uninstall them first pr pera Ped towhich the receiver is connected This product may not operate correctly if a driver made by another Device Manager Con
13. g the receiver unit a f n M oon interference and 2 this device must accept any interference received Installing Replacing the Battery on the reverse of this sheet and ae i i This product is hot pluggable It is possible to disconnect the receiver unit l e Windows XP including interference that may cause undesired operation 3 The mouse driver is installed automatically when PCis running replace the batteries as soon as possible e The alkaline batteries supplied with this product are for 1 From the Start menu right click My Computer NOTE This equipment has been tested and found to comply with the Operation may become unstable if the receiver unit is checking product operation These batteries may discharge 2 Click Properties Ga limits for a Class B Digital Device pursuant to part 15 of the FCC Rules disconnected and reconnected several times when PC is f f f AE See Boore These limits are designed to provide reasonable protection against and drain during storing and shipping Search f ears running If this occurs restart PC 3 Click the Hardware tab E conr rena harmful interference in a residential installation This equipment When not using the mouse turn it off to save battery power It is possible that the standard Windows mouse driver did not install correctly and that this product is detected as an unknown device by Windows This product is usually detected as a USB human inter
14. he receiver unit is disconnected and reconnected several times when PC is running If this occurs restart PC F 7 T g l FAAUE SS 3 HEA JSA WE o Troubleshooting Basic specifications m BRN oog When using Mac OS X Ol JIE NAS BS ANUSHIISA ze ao d ASSES J K AS SSCS OH SE NAAN ASS USLC When the product appears to be Removing an unknown device ee Eee ea Mas e malfunctionin A A A Article No M NE2DR Series Sten1 Check USB ports Stepd Checking operation g If the standard Windows mouse driver did not install correctly and Os Windows 7 up to SP1 Windows Vista up to SP2 E When the mouse pointer on the screen does not move this product is detected as an unknown device remove the unknown Windows XP SP2 to SP3 2 Check the USB port on your computer Check that the vertical scrolling functions are working correctly or moves unstably when the mouse is moved device from Device
15. m a mobile phone causes this product to malfunction slow down or fail to operate e Do not use this product in a hospital or other locations where the use of radio waves is prohibited The radio waves of this product may affect electronic and medical devices e g pacemaker e The use of a wireless mouse in an aircraft is prohibited by aviation law because doing so may interfere with flight safety Turn off the power of the mouse body before boarding an aircraft and do not use it in the aircraft ELECOM is not liable for any accident or social damages incurred by the failure of this product Package Contents This product s packaging contains the items listed below Before using the product check that all items are present We make every effort to ensure that all products are packaged correctly However in the event that an item is missing or damaged contact the retailer from whom you purchased the product e Mouse x1 e Receiver unit x1 e AAA alkaline battery x1 e User s Manual x1 Part Names E Mouse E Receiver unit Left button Used for left click operation 2 Right button Used for right click operation Q Wheel The wheel can be turned back and forward with your finger or pressed like a button to operate the PC Receiver unit housing Used to store the receiver unit Power switch Used to turn the mouse body on and off Optical sensor
16. om your system 1 st edition December 1 201 1 restart the PC ELECOM Co Ltd E LECO M CO 3 LT D e This manual is copyright of ELECOM Co Ltd 4 1 Fushimi machi 4 Chome Chuoku Osaka Japan 541 8765 e Unauthorised copying and or reproducing of all or part of this RL htto al 760 inidloball manual is prohibited lisesi i aac M soprana e The specifications and appearance of this product may be changed without prior notice for product improvement purposes Hees bist BAAR l e ELECOM Co Ltd shall bear no responsibility for any and all affects isi Re kk S328 1065 FS AREBRRAIS 704 resulting from the use of this product regardless of the above fag 86 21 3368001 1 reasons FAX 86 21 64271706 e Export or service transaction permission under the Foreign URL http www elecom china com Exchange and Foreign Trade Control Law is required in order to ELECOM Korea Co Ltd export this product or parts of this product that constitute strategic 5F Suam Bldg 1358 17 Seocho2 dong Seocho gu Seoul materials or services 137 862 Korea e Windows and the Windows logo are trademarks of the Microsoft TEL 1588 9514 group of companies FAX 02 3472 5533 e Mac Mac OS and Macintosh are registered trademarks or URL www elecom co kr trademarks of Apple Inc in the United States ELECOM Singapore Pte Ltd e Company names product names and other names in this 33 UBI AVENUE 3 03 56 VERTEX SINGAPORE 408868 manual are gen
17. sult the dealer or an experienced radio TV technician for help company is installed See the instruction manual that was supplied A Notice Changes ar Ioalhications not expressly approved by the pariy pay EES Divar Siaina leta va malka sure thats divamam responsible for compliance could void the user s authority to operate with your previous mouse for uninstall instructions It is possible that the driver is conflicting with another driver such as that for a laptop touch pad To use this product the equipment Any changes or modifications not expressly approved by ELECOM responsible for compliance could void the user s authority to operate the equipment 2 The Device Manager window appears Right click the unknown device and click Uninstall correctly you must delete the touch pad driver However if you OFEN delete this driver you may not be able to use the touch pad or Pea touch pad functions Contact the PC manufacturer for more 3 WARNING This product contains a chemical known to the State of details California to cause cancer birth defects or other reproductive harm E The wheel moves but the mouse cursor does not In certain applications that do not support the scrolling function the mouse cursor will not move when you move the wheel Wireless Optical Mouse 3 Click f M NE2DR Series Unknown Device User s manual 4 Disconnect the receiver unit and Warming You are about to uninstall this device fr
18. t without being operated for a certain period of time with the power or switch turned on Inserting and Taking Out the Receiver Unit E inserting the receiver unit 7 Place the receiver unit into the receiver unit housing E Taking out the receiver unit Lf Qa 1 Take the receiver unit out of Q Fy the receiver unit housing Receiver unit stowed Step Checking operation Check that the mouse scrolls up and down correctly in Windows Internet Explorer 7 From the Start menu select All Programs and then Internet Explorer Internet Explorer will launch 2 Display your favourite web site in Internet Explorer and change the size of the window so that the vertical scrollbar appears The sample website used here is the ELECOM homepage ELECOM WEB SITE Windows Internet Looks Explorer OO B elecom c i v 4 x E sin jel tes E M D v Pager Safety Toolse e scrollbar 3 pisin the tilt wheel back and forth IM WEB SITE Windows Internet Explorer The mouse is operating ngiall if the screen moves up and down as you scroll the tilt wheel Q In applications that do not support scrolling the screen will not move when you scroll the tilt wheel E Disconnecting the receiver unit This product is hot pluggable It is possible to disconnect the receiver unit when PC is running Operation may become unstable if t

[PDF:1.8MB]

Contents

Download Pdf Manuals

Related Search

Related Contents