USER MANUAL - Tanning Bed Parts
Contents
1. 15 ed p 3 a KS Timer Maintenance Your SunOuest sunbed is eguipped with a backup shut off timer which will automat ically turn off the sunbed in the unlikely event of a malfunction of the primary timer This important safety feature also prevents the user from re setting the timer before the end of the pre set maximum time interval The electronic timer limiting circuit is automatically reset each time the primary timer is turned to the OFF posi tion Annually or whenever your sunbed is re lamped check the operation and accura cy of the timer system as follows DO NOT perform these tests with a person in the sunbed 16 R Care and Maintenance Timer Maintenance Step 1 Obtain an accurate watch capa ble of measuring in seconds Set the timer to its maximum inter val Using the watch time how long the lamps remain on The lamps should shut off within plus or minus 10 of the maxi mum timer interval Set the timer to the maximum time interval Wait ten minutes then turn the knob back to the maximum time position The electronic time limiting circuit should turn the lamps off at an elapsed time egual to approxi mately 10 beyond the maxi mum timer interval even though the primary timer con tinues to show time left Step 2 Call ETS Customer Service if your timer does not operate properly or if you expe rience difficulty2. 9 22675B 1 Attaching Canopy to Bench Lift the canopy and hold it between the hinge brackets You may want to use some of the cardboard packing laid across the bench to support the canopy 2 wee Installation Assembly Procedures A 4 ma Insert the 5 16 x 1 1 2 bolts with the nylon washers into both hinge brackets Tighten bolts into the end cap threaded inserts until snug then an additional half turn Do not over tighten to avoid damaging threaded inserts 7 RY A Ti Attaching Gas Springs 1 PIVOT STUD l D ed O Installation Assembly Procedures The gas springs are shipped with locking clips installed These clips must be removed before the gas springs can be installed With a helper holding the canopy open align open ends of gas spring ball joints with pivot studs and push into place Be sure spring cylinder is in up position as shown DO NOT lower canopy until both gas springs are installed Failure to install locking clips may result in the gas springs working loose allowing the canopy to fall which may cause serious injury 3 Lift and lower canopy a few times to lubricate gas springs for optimum performance Your gas springs contain one of these two types of ends Remove locking clips as shown X 9 22675B D d N 4 Installation Making Electrical Connections A Rh ma Making
3. F 26RS 26RST ro 24RS 24RST 24RS USER MANUAL 226758 Limited Lifetime Warranty SunQuest warrants your tanning unit to be free of structural defects in its material and workmanship under normal use for its lifetime SunQuest will repair or replace at their discretion any defect to the structure which affects the performance of the unit For 6 months from the date of purchase SunQuest will provide replacements for parts that prove to be defective in material or workmanship Acrylic shields fluorescent lamps and lamp starters are excluded from this warranty Labor will be covered for 30 days from pur chase date Normal wear damage from misuse or abuse damage incurred in transit or damage done by unauthorized repairs or modifications are not covered by this warranty ETS Inc disclaims any implied warranty of merchantability or fitness for any period beyond the expressed warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you No one has authority to change or modify this Limited Lifetime Warranty in any respect To obtain service under the Limited Lifetime Warranty contact ETS Inc at 1 800 449 3605 and ask for the Technical Service Department ETS Inc shall not be liable for loss of use loss of time inconvenience rental or substitute products loss of business loss of income or any other incidental or consequential damages Some states
4. Se LO lt T T LU T x gt oO O m XG y mE W X O 3 MX E amp Q LAMPS LEGS 22675B Parts List When calling for parts first state your bed model as H 24RS H 24RST H 24RSF H 26RS or H 26RST Then refer to this list and illustration for proper part identification Acrylic Bench Acrylic Canopy Acrylic Vinyl Strips 24RS 24RST only Ballast 30W for Turbo lamps Ballast 80W for short lamps on 24SF Ballast 100W 1 for each main lamp 4 for each face tanner lamp Capacitor 75uF Contactor Relay Cover Bench Cover Canopy Endcap Kit 1 left and 1 right endcap Fan Gas Spring set Hardware Kit assembly hardware Hinge Brackets left and right Lamp Holder Turbo Starter Holder Turbo Lamp Holder w Starter Lamp Holder w o Starter Lamp Holder Face Tanner Lamps Leg Mounts found inside the bench Legs Manual Pillow Profile blank Redundant Timer Remote Bypass Plug Schematic Packet Silk screened Profile Skirt Kit front 2 sides and screws optional Starter S 2 Turbo Starter K 11 main lamps Starter Face Tanner ignitor Switch Face Tanner Thermostat Face Tanner Timer Timer Bezel Timer Knob Trim Profile blue Not shown Record this information for ease of service Date of purchase Bench serial number Canopy serial number CALL FOR SERVICE OR QUESTIONS 108000449 3605 ETS Inc 6270 Corporate Drive
5. x 1 Quantity 8 5 16 Metal Washer BRL Ouantity 6 5 16 Metal Washer Ouantity 2 Bushing Ouantity 2 Allen head Bolt 5 16 x 1 1 2 Ouantity 2 Nylon Washer Ouantity 2 Hinge Brackets Ouantity 2 left and right aSZ9TT 22675B Installation Assembly Procedures Attaching Legs to Bench 1 Using six 5 16 x 1 bolts and the six Lay the bench upside down on the floor larger 5 16 washers may be pre Locate the two stand legs and attach to the installed attach the stand legs with bench as shown below the skirt mounting holes toward the back of the bench as shown Install center bolt first You may have to gen tly push sides of legs in to align holes Tighten with the Allen wrench SKIRT MOUNTING HOLES ELECTRICAL CONNECTOR INDICATES BACK OF BENCH 2 Turn bench right side up on floor Place so that the power cord connec tor is facing toward the wall outlet ed M A i Installation Assembly Procedures PR Attaching Hinge Brackets to Bench Locate the two hinge brackets and identify the left and right brackets 1 Install the hinge brackets to the ends of the bench such that the short boss engages the stud above the bolt hole and the long boss engages the hole below the bolt hole Secure using the 5 16 x 1 Allen head bolts and 5 16 metal washers Tighten bolt snug then an additional half turn 2 Place the bushings into the hinge brackets as shown below
6. 24RST 22675B i 2 09 lu 1 o W Ea ow x 4 lt Z Ps A I Ka z og 5 lt A Q Eu zo U lt H 8 qe TT y O 4 gt A lt ZM o JPN Vi Lal D WE vee m A O i Z J lt 1 gt 4 S l r LU az Z Og E TE KL Fu op vo pY E va TRIM PROFILE COVER BENCH LAMPS LEGS H 24RSF COVER CANOPY TRIM PROFILE CAPACITOR 9 Z o na nd 5 O U L E lt o 2 gt lt lt a S oc Os ja N ES H N O lt X z lt A Fi 6 E 2 0 l y lt A 5 M AN 7 gt ZDA Va VA N N M Y V 4 x m 9 i AN M m o W Z gt MY Ul S ae gt E O Z p W Lu 5 lt Yu EE 22 Su va NO 2 73 COVER BENCH PROFILE LAMPS 94977 H 26RS CONTACTOR RELAY BALLAST CAPACITOR COVER CANOPY TRIM PROFILE GAS SPRING LAMP HOLDERS REDUNDANT TIMER LAMPS ENDCAP TIMER KNOB TIMER SILK SCREENED PROFILE COVER BENCH PROFILE LEGS H 26RST O 7 79 X a amp gt A 2 3 2 n 5 gt lt lt X lt lt PS 8 o S lt A G Fi A ZE a OQ O n a S l lt m gt x S E lt sl m E 38 25 Der gt Y gt a US 2 O N x lt TZ Li LH OZ EE Yu
7. soft cloth We recommend SunQuest disinfectant and SunQuest acrylic cleaner Thorough Periodic Cleaning Introduction The cooling fans draw air through the bed and over time will cause a dust buildup on the lamps and reflectors This will reduce the tanning effectiveness of the bed When a dust buildup is observed it is necessary to thoroughly clean the inside of the bench and canopy Warning Disconnect sunbed from electrical power before cleaning Cleaning the Canopy and Bench Step 1 Remove the acrylic shields and lamps as described in Replacing Lamps With a soft cloth wipe the entire length of each lamp to remove any film buildup Step 2 12 AGE Pp lg and Maintenance Step3 Clean both sides of the acrylic shields with a non ammonia dis infectant cleaner Step 4 Wipe the reflectors with a clean damp cloth Step 5 Re install the lamps and acrylic shields Mechanical Inspection Your tanning bed has been built for years of service To ensure trouble free operation throughout its life inspect the unit s mechanical integrity every 400 500 hours of use e Inspect the units fasteners verifying that all are firmly in place Pay partic ular attention to the hinge bolts e Inspect gas springs for signs of wear Gas springs that will not hold the canopy in the full open position when raised should be immediately replaced e Inspect the timer as indicated in this manual under Timer Maintenance e Insp
8. tanner unit 14 9 22675B Care and Maintenance Replacing Lamps N Removing Replacing Face Tanner Lamp on F Models After removing the canopy acrylic shield replace the face tanner lamp as follows Step 1 Support the face tanner assembly with your hand while unscrew ing the two retaining screws The face tanner glass casing will swing downward Step 2 The lamp can now be exchanged The lamp holders are eguipped with spring con tacts which enable the lamp to be removed easily Remove the old lamp and discard Install the new lamp using a clean cloth or paper towel Ensure that the lamp is firmly seated in the lamp holders wi 7 RE Note Never take hold of the lamp such that your fingers are in contact with the lamp glass Finger oils will greatly reduce the lamp s operational life Step 3 Gently close the face tanner glass casing and lock it closed with the screws Ensure that the screws firmly secure the glass casing WARNING Never turn the equipment on while the face tanner is disassembled or when the glass filters have been removed The direct light can cause severe injury to the eyes and to other areas of the body Immediately discontinue use of this equipment if the face tanner glass is bro ken or if any unfiltered light can be seen escaping the face tanner assembly RETAINING 18 SCREWS
9. Connections 9 Operation seses iva ar A a wines 10 Before YOU Tanseer cceur tiua salat ASEEN 4 10 Exposure TIMES 4354004 436 460 5 de di da 10 Using Your Sunbed A Greide eden 11 Care and Maintenance 12 Cleaning After Usuario 12 Thorough Periodic Cleaning lt lt lt 12 Mechanical Inspection esci 64 00508 ead hea ee nels 12 Replacing Lamps suusta aasia aan Kiinan ananas teed 13 Timer Maintenance s lt a Pea ia ea 16 Troubleshooting lt sasasssa asa usa a Essu at 17 Obtaining Service 4 44 4400 back cover D M N n gt BOP afety Information PI LABELING NOTICE Labels are affixed on all systems to inform the user of possible dangers Regulations are stated in 21 CFR Section 1040 20 and require that all products manufactured after September 8 1986 which use sunlamps must display the following DANGE Ultraviolet radiation Follow instructions Avoid overexposure As with natural sunlight overexposure can cause eye and skin injury and allergic reactions Repeated exposure may cause premature aging of the skin and skin cancer WEAR PROTECTIVE EYEWEAR FAILURE TO MAY RESULT IN SEVERE BURNS OR LONGTERM INJURY TO THE EYES Medications or cosmetics may increase your sensitivity to the ultraviolet radiation Consult physician before using sunlamp if you are using medications or hav
10. Electrical Connections 1 Connect the canopy to bench power Warning Be sure AC power is discon cord to the bench receptacle The plug is polarized Align the terminals and firmly push on until seated then tighten the threaded locking ring nected before connecting cables POWER CORD THREADED 2 Plug the three prong 220V AC power LOCKING W cord into a dedicated outlet see Pre Installation Planning RECEPTACLE ON BENCH CANOPY TO BENCH POWER CORD we id gt 4 ASIN peration F RR Before You Before using your sunbed please note the following important precautions e Your skin should be free of cosmetics tanning oils or other body lotions prior to tanning except for those specifically made for use with tanning devices However do not remove nat ural body oils by bathing or showering immediately before tanning e Your hair should be free of gels mousses sprays or other hair products prior to tanning These products can cause damage to the sunbed acrylic As an alternative a shower cap or towel can be worn to keep treated hair away from the sunbed surfaces e As with all electrical appliances do not operate this device near water or while you are wet Level 1 Week 1 Ist 3rd Sessions Skin Type e Some medication may increase your sensitivity to ultraviolet light It is rec ommended that you consult a physi cian before using this sunbed if taking any medication or if you su
11. Indianapolis IN 46278 2900 CALL FOR SERVICE OR QUESTIONS 1 800 449 3605 FAN 6270 Corporate Drive Indianapolis IN 46278 2900
12. do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which may vary from state to state All warranty service must be performed by an authorized service person If your tanning unit must be returned for service all freight charges must be at your expense Contact your place of purchase for the address of the SunQuest Service Center nearest you Proof of purchase is required to obtain warranty service W3 This warranty covers the original purchaser only This warranty is void if the unit is modi NE PA i PRS fied in any manner from its original design Wez gsZ9tz 22675B we PUY k come Congratulations on your purchase of this technologically advanced sun tanning unit It has been designed to provide years of dependable service for you Please read all the instructions in this booklet before installing and using the unit Always be sure to observe all safety precautions ld M RC ontents PR Safety Information iii ET deda a necne KEEN KA A A 1 Unpacking and Inspection sessa Aa ne SSR edan ukia 1 ToolS Required 2325338 838 a 6 dd id kanne 2 Pre Installation Planning lt 44 44 lt lt lt raner 3 Assembly Procedures 2 sos eee eee eee 4 Making Electrical
13. e a history of skin problems or believe yourself especially sensitive to sunlight If you do not tan in the sun you are unlikely to tan from the use of this product To use lie down under canopy and pull down as far as adjustment will allow Minimum use distance from face tanner is 1 inch or 2 54 centimeters Minimum use distance elsewhere is touching the clear plastic panels Do not use without clear plastic panels in place Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tanning nor mally appears after the first few sessions and maximizes after approximately four weeks Tan once or twice per week thereafter to main tain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 20 MINUTES Level 1 Week 1 Subsequent Skin Type Ist 3rd Sessions UNGE revers BM Maximum 8 12 16 20 20 IV Dark Burns minimally tans easily and above average New lamps emit approximately 20 more ultraviolet radiation during the first 50 hours of operation Recommended tanning times should therefore be reduced by approximately 20 during that period WARNING e Read the instructions booklet before using this sunlamp product All persons in the room should wear protective eyewear when lamps are on Recommended eyewear provided eyeshields Lucas Products Super Sunnie
14. ect the AC power cord and its connections e Inspect the acrylic Broken cracked or badly scratched acrylics should be immediately replaced 9 22675B W Care and Maintenance Replacing Lamps N N Replacing Lamps Introduction To be assured of maximum tanning effec tiveness change lamps after approximate ly 800 1000 hours of use Tanning will continue after this time but at a slower rate To ensure trouble free operation of your sunbed replace the lamp starters whenever the lamps are replaced Warning Disconnect sunbed from elec trical power before servicing Removing Replacing Acrylic Shield The acrylic shields in the bench and canopy are secured in place by hinged profiles which run the length of the bed both front and back Simply pry up on the inside edge of the profile until it releases its latching action see figure at right Continue to pry up the profile across its entire length until it swings back freely Repeat for the other profile The long edges of the acrylic shield are now exposed Standing in front of the sunbed grasp the exposed edge of the acrylic and carefully slide it toward you until it is removed After changing the lamps replace the acrylic shields by reversing the above directions Close the hinged profile by pushing it back into place until it snaps tight NOTE Be careful The edges of the acrylic shield may be sharp 13 2 E Removing Replacing Lamp
15. lastic wrap and the carton packaging Do the same for the canopy Do not try to lift either unit with the plastic still on as it may slip Note The cartons are reusable in the unlikely event that you may find it neces sary to return your sunbed The canopy box contains the canopy unit and a pair of gas springs The bench box contains the following items e Bench Unit e Box containing necessary assembly hardware safety goggles and pillow e Box containing two stand legs Inspect these items including the canopy and bench and make sure they are free from any visible damage Report the extent of any damage to the transportation company Record the serial numbers of the canopy and bench in the area provided at the back of this manual This information will be reguired whenever you call customer service RY Pp 3 ms A Installation Tools Required PR Tools Required You will need the following tools to assemble your sunbed Utility Knife Allen Wrench Supplied in hardware kit 9 22675B Pre Installation Planning Before you begin to assemble your sunbed you should observe the following pre installation considerations Your sunbed operates from a 220V AC source You should have a NEMA 6 20R electrical outlet like the one shown below installed in the room in which you will use the unit The outlet should be on a dedicated cir cuit capable of providing 20 Amp service We recomme
16. nd installation by a professional electrician The outlet must be earth grounded 20 AMP NEMA 6 20R RECEPTACLE D d N Installation Pre Installation Planning N N RA e Make sure the room in which you intend to use your sunbed is well ventilated Air from the room is used to cool the sunbed and a poorly ventilated room may cause the unit to become hot and cause discomfort to the user e Your sunbed is designed to operate in an ambient room temperature of 80 F maximum and 70 relative humidity e Place your sunbed no closer than 6 from any wall Make sure that cur tains drapes and other room furni ture do not obstruct the airflow into the end caps or out of the fan open ing areas e Proper assembly of your sunbed requires three people Plan to have a couple of helpers assist you Use of a voltage source above 230V AC may prevent proper operation of the sunbed and could cause damage and void the warranty ed M gt KA E AN A Installation Assembly Procedures PR Assembly Procedures Hardware Inventory Use the utility knife to cut open the hard ware box and remove the small bag of hardware In addition to a small Allen wrench and pillow make sure you have the following hardware items NOTE The larger 5 16 metal washers and six 5 16 x 1 Allen head bolts may be pre installed in the bottom of the bench Safety Goggles CeTe gt Ouantity 1 Allen head Bolt 5 16
17. rned on without wearing the appropri ate protective goggles Step 1 For units equipped with a face tanner activate the face tanner by placing the rocker switch located next to the timer knob into the 1 ON position If you do not wish to use the face tan ner leave the switch in the O OFF position NOTE The F model face tanner lamps need a longer after use cooling period before they will light again Put on your goggles Set the timer to the desired number of minutes after first determining the proper time period from the Step 2 Step 3 Step 4 FACE TANNER ROCKER SWITCH table on the previous page The lamps will turn on as soon as you move the rotary dial from the 0 position Lift the canopy lie down on the bench face up and lower the canopy toward your body For best results position the canopy as close as possible to your body but do not bring the canopies with face tanners any closer than 1 inch from your body When the timer reaches 0 the lamps will automatically turn off and the cooling fans will run for approximately 3 minutes during the Cool Down period 11 D yy Cleaning After Use Clean and disinfect your tanning bed s bench and canopy after each use Use a non abrasive disinfectant cleaner that does not contain ammonia or ammonia deriva tives Ammonia may damage the acrylic shields Spray the acrylic lightly with disin fectant and wipe dry with a clean
18. s AE After removing the acrylic shields replace lamps as follows Step 1 Grasp a lamp at one end and at the middle then turn the lamp a quarter turn The lamp may then be gently removed from its holder Step 2 To reinstall a lamp insert the pins located on the ends of the lamp into the slots on top of the lamp holder and turn the lamp a quarter turn Care and Maintenance Replacing Lamps Recommended Replacement Lamps We recommend using the lamps specified below Use of uncertified lamps is a viola tion of Federal regulations and will void your warranty These lamps have an aver age life of 800 1000 hours of effective tanning use Lamps used longer than that begin to lose their effectiveness even though they will continue to light ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RS MODEL SERIES Velocity Wolff amp Model VEL 71 T12 100W 24RS 24RST 24RSF Diamond Sun amp S Wolff amp Model DSS71 T12 100W 24RS 24RST 24RSF and 26RS 26RST THE FOLLOWING ADDITIONAL LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RST MODELS Turbo Sun S Wolff amp Model F8 T5 10W 24RST and 26RST Turbo face tanners THE FOLLOWING ADDITIONAL LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RSF MODELS Velocity Wolff amp Model VEL 59 T12 080W 24RSF short lamps Diamond Sun amp S Wolff amp Model DSS59 T12 080W 24RSF short lamps Philips Model HPA 400 30s or CosmoTech Model 23045 or CosmoTech 20046 24RSF Face
19. s or Intrexco No 5635 1 or eguivalent eyewear as defined under 21 CFR 1040 20 Other types of eyewear may not provide adeguate protection ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RS MODEL SERIES Velocity Wolff Model VEL 71 T12 100W 24RS 24RST 24RSF Diamond Sun S Wolff Model DSS71 T12 100W 24RS 24RST 24RSF and 26RS 26RST THE FOLLOWING ADDITIONAL LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RST MODELS Turbo Sun S Wolff Model F8 T5 10W 24RST and 26RST Turbo face tanners THE FOLLOWING ADDITIONAL LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RSF MODELS Velocity Wolff Model VEL 59 T12 080W 24RSF Short lamps Diamond Sun S Wolff Model DSS59 T12 080W 24RSF Short lamps Philips Model HPA 400 30s or CosmoTech Model 23045 or CosmoTech 20046 24RSF Face tanner unit DISCONNECT POWER CORD BEFORE ATTEMPTING TO CLEAN RELAMP OR ENGAGE IN THE MAINTENANCE OF THIS PRODUCT THIS EQUIPMENT MUST BE EARTH GROUNDED THIS PRODUCT IS INCONFORMITY WITH PERFORMANCE STANDARDS FOR SUN LAMP PRODUCTS UNDER 21 CFR PART 1040 20 gsZ9zz 22675B e M ME sc 3 nstallation F RE Unpacking and Inspection Your sunbed comes in two cardboard car tons one for the bench and one for the canopy Open the cartons and remove the bench and canopy as follows The bench and canopy are each wrapped in plastic Pull back the plastic and with a helper grasp the bench and pull it from the carton bottom leaving the p
20. spect that your skin might be especially sensitive to sunlight Included with this manual is an FDA booklet on medications that increase sensitivity to light Exposure Times Follow the guidelines for skin type and exposure times as shown in the table below Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approxi mately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan Subsequent 1901 Maximum Level 2 Level 3 I Sensitive Skin Burns easily and severely and does not tan NOT RECOMMENDED FOR TANNING 11 Light Burns easily and severely and tans minimally 4 8 12 16 20 III Normal Burns moderately and tans average 10 15 20 20 IV Dark Burns minimally tans easily and above average 10 6 8 12 16 20 20 9 22675B Using Your Sunbed Once you have read Before You Tan and Exposure Times you are ready to use your sunbed Proceed as follows WARNING Your sunbed is designed for individual use Only one pair of protec tive goggles is provided Always wear these or another approved pair of goggles Regular sunglasses do not provide ade quate protection from ultraviolet light You should never look at the lamps when tu
21. with these tests 9 22675B Lamps fail to light One or more lamps fail to light Canopy fails to stay in the up or down position Sunbed does not stay lit Check source of AC power Reset circuit breaker or replace fuse if necessary Make sure the unit is plugged into outlet Make sure cord between canopy and bench is properly connected Make sure timer dial is turned to a number past 0 Check that lamp is installed correctly Switch unlit lamp with a lamp that lights If the new lamp lights and the old lamp still does not replace old lamp If replacing lamp does not remedy problem con tact your service representative Gas springs should hold the canopy fully open as well as allow it to rest fully closed If the canopy is left open for an extended period of time it may creep down This is considered normal Keep the canopy closed when not in use Replace gas springs when they no longer have sufficient power to hold the canopy open when raised Check source of AC power Reset circuit breaker or replace fuse if necessary Check timer system per maintenance instructions in this guide Contact your service representative 22675B SdWV1 s931 SHIGTOH dIAVT dVO0N3 ONIYdS SVO YAWIL J 1404d GANA44IS M IIS 2 HONE HIA00 J 1404d JIWIL INVANNAIY Av138 HOLOVLNOO 1SVTIVE YOLIOVdVD v AdONVO HIA00 WIR SUPT H H
Download Pdf Manuals
Related Search