Freedom Par Hex-4 User Manual Rev. 2
Contents
1. DOWN to select the transmitting signal dt 1 dt16 Manual Sync en os Ce I For the receiving product s 1 Press lt MENU gt repeatedly until S tr shows on the display 2 Press ENTER 3 Press UP or DOWN until drCH appears on the display 4 Press ENTER 5 Use UP or DOWN to select the receiving signal dr 1 dr16 The channel number should match the transmitting signal you chose when setting up the transmitting product N To sync multiple transmitters in one room manually set each receiver and the designated transmitter to a specific frequency and then perform the syncing steps Freedom Par Hex 4 is fully compatible with the D Fi 2 4 GHz wireless transceiver E transmitter receiver from Chauvet sold separately For more detailed information about D Fi 2 4 GHz functionality refer to the D Fi 2 4 GHz User Manual available at the Chauvet website www chauvetlighting com D Manual syncing is recommended for best results Page 12 of 21 Freedom Par Hex 4 User Manual Rev 2 D Fi M 2 4 GHz The Freedom Par Hex 4 offers wireless control of 2 or more products with a single DMX controller To DMX Mode automatically set up D Fi 2 4 GHz syncing for DMX do the following For the receiving product s Auto Sync 1 Press lt MENU gt repeatedly until S tr shows on the display 2 Press lt ENTER gt 3 Press UP or lt DOWN gt until drAS appears on the display 4 Press2. ENTER 5 The display should show drAU For the transmitting product 1 Press lt MENU gt repeatedly until S tr shows on the display 2 Press ENTER 3 Press UP or DOWN until dtAS appears on the display 4 Press ENTER 5 The display should show dtAU Receiving units must be set up before the transmitting unit Once the steps above are done press and hold lt AUTO gt on just the transmitter for approximately 30 seconds The display and signal LED will flash to indicate sync is activated You can then back out to a general menu level and configure the transmitting product to operate it with a DMX controller To configure your product to work with DMX refer to the Starting Address section To add additional Freedom products turn the synced ones off and repeat the above steps with unsynced products Once all products are synced turn them all back on Auto scan syncing must be done within a distance of about 32 ft 10 m Manual syncing is recommended for best results when adding products after initial system setup If you are experiencing issues or need to improve signal quality keep the line of sight between products unobstructed Ensure that all linked products are configured to the same DMX personality transmitter and receiver such as water snow or people For best results keep the line of sight Caution D Fi 2 4 GHz operation can be interrupted or inhibited by liquid masses between the
3. D clear of any liquid mass DM X Controller Board Hue 100 OO mL Linking Products mos O YEN3T1081NO2 o Wireless D Fi Hub DM X compatible Brand X product gt To more DM X compatible products DM X compatible Brand X product Freedom Par sends wireless DM X signal to DM X compatible products wirelessly or via DM X cable Freedom Par Hex 4 User Manual Rev 2 Page 13 of 21 DMX Channel The following tables show which DMX channels control which functions in each of the DMX personalities Assignments and Be sure to become familiar with these values when operating the product with a DMX controller Values 12CH Channel Function Value Setting No function 011 030 R 100 G 0 100 B 0 031U 050 R 100 0 G 100 B 0 0510 070 R 0 G 100 B 0 100 0710 090 R 0 G 100 0 B 100 091 110 R 0 100 G 0 B 100 111U 130 R 100 G 0 B 100 0 131 150 R 100 G 0 100 B 0 100 151U 170 R 100 0 G 100 0 B 100 R 100 G 100 B 100 A 100 8 Manual Color 201 U 205 Color temperature 1 Color temperature 2 211U 215 Color temperature 3 Color temperature 4 221U 225 Color temperature 5 Color temperature 6 231 U 235 Color temperature 7 Color temperature 8 Color temperature 9 Color temperature 10 Color temperature 1 1 B SE No function 0110 255 Slow to fast Page 14 of 21 Freedom Par Hex 4 User Manual Rev 2 12CH Channel 10 11 12 8 C
4. uktech chauvetlighting com Brookhill Road Industrial Estate Pinxton Nottingham UK World Wide Web www chauvetlighting co uk NG16 6NT Voice 44 0 1773 511115 Fax 44 0 1773 511110 MEXICO Chauvet Mexico General Information Technical Support Address Av Santa Ana 30 Email servicioMOchauvet com mx Parque Industrial Lerma Lerma Mexico C P 52000 World Wide Web www chauvet com mx Voice 52 728 285 5000 Outside the U S United Kingdom Ireland or Mexico contact your dealer Follow their instructions to request support or to return a product Visit our website for contact details Freedom Par Hex 4 User Manual Rev 2 Page 21 of 21
5. 1 S100 slow to fast 3 Press ENTER To select a dimmer speed mode do the following 1 Press lt MENU gt repeatedly until dIM shows on the display 2 Press ENTER and one of the following shows on the display OFF dimmer speed off dIM1 dimmer speed mode 1 fast speed dIM2 dimmer speed mode 2 middle speed dIM3 dimmer speed mode 3 slow speed 3 Use UP or DOWN to select the desired dimmer speed mode 4 Press ENTER To select a preset static color do the following 1 Press lt MENU gt repeatedly until C shows on the display 2 Press ENTER 3 Use UP or DOWN to select the desired preset color C 1 C 63 4 Press ENTER To custom mix a color follow the instructions below 1 Press lt MENU gt repeatedly until U shows on the display 2 Press ENTER and one of the following colors shows on the display rXXX red gXXX green bXXX blue AXXX amber WXXX white or PXXX UV 3 Press lt ENTER gt repeatedly to select the desired color 4 Use UP or DOWN to select the desired color value 0 255 NOTE Selecting 0 will turn the color off 5 Press lt ENTER gt to select color value and continue to the next color 6 Repeat steps 3 to 5 until you create your desired color Freedom Par Hex 4 User Manual Rev 2 Infrared Mode Infrared IR mode allows the product to be controlled with an infrared remote controller The IRC 6 can remotely set the produc
6. Consumption 35 W 34 W Operating current 0 3 A 0 2A Power linking current units 8 A 26 units 8 A 50 units Fuse T2A 250V T 2A 250 V Power I O US Canada UK Worldwide Power input connector IEC IEC Power output connector Edison IEC Power cord plug Edison US Local plug Type Power Lifespan LED 10 W 50 000 hours Color Quantity Current Hex color RGBAW UV 4 2A Parameter Field angle 34 Beam angle 23 Strobe rate 0 to 25 Hz Illuminance O 2 m 1 372 lux Maximum External Temp Cooling System 104 F 40 C I O Connectors Convection Connector Type Channel Range 3 pin XLR Sockets 6 8 or 12 Product Name Item Code UPC Number Freedom Par Hex 4 03030875 781462212230 ROHS Page 19 of 21 To return a product or request support R ETU RNS In the U S contact Chauvet World Headquarters see Contact Us In the UK or Ireland contact Chauvet Europe Ltd see Contact Us In Mexico contact Chauvet Mexico see Contact Us In any other country DO NOT contact Chauvet Contact your distributor See www chauvetlighting com for distributors outside the U S United Kingdom Ireland or Mexico If you live outside the U S United Kingdom Ireland or Mexico contact your distributor of record and follow their instructions on how to return Chauvet products to them Visit our website for contact details Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization RMA number befor
7. ee 13 Wiaiinelziiosiic tH nen S 13 DMX Channel Assignments and Values cccccccsseececceeeeececcaeueeceeceeseeeeesaeauceeeseaasceeessaaeeeesseausceesseaaeeeeesuaueeeesssagecesssaneeess 14 Gornfiduratondoteandalorig soam tie itio nt ted indonesia 16 Sound Active Modera dl rH 16 SUN IIS ASMA e dd dd e do Souls o 16 A A een iuter 16 o A e 16 Selecting the Dimmer Speed Mode leser a e a e iia a 16 S A O O En nn LE AR 16 CUSTOM COMINO sra Dm 16 lc IMIOG GS ihc ME Fe MN 17 HAG GOD A E o m ES 17 9 Technical INTOFM AION aii E E 18 PROG UGE IVI IUCN AIG o sennae E E E A TP eee ee 18 6 technical SHECINCAUONS e 19 A NEN NE Rm NO E TN 20 Goin rz A EE CR RR 21 1 BEFORE YOU BEGIN What Is Freedom Par Hex 4 Warranty Card Power Cord Quick Reference Guide Included IRC 6 Infrared Remote Control Unpacking carefully unpack the Freedom Par Hex 4 and check that all the parts are in the package and are in Instructions good condition Claims f the box or any of the contents appear damaged from shipping save all the packaging and file a claim with the carrier immediately Failure to report damage to the carrier immediately or failure to save all the packaging can invalidate a claim For other issues such as missing components or parts damage not related to shipping or concealed damage fil
8. FREEDOM Parm HEXx 4 User Manual CHAUVET CS Green Thinking Freedom Par Hex 4 User Manual Rev 2 TABLE OF CONTENTS 1 BOTORS You BOON wc t 3 Wat zw AC UGS Cia cae ete tcn DOE Tcr Teo 3 WAP ack linGh ASMA utr c soeeaeeancceauie eee 3 CGI Store sear veces tragic D UI NITET 3 TEXT CONV 7 110 ER RTT TN 9 VITO I SE NM DT OD Ems 3 a 3 PEO UC AULA delos o cali el iO 4 2 uiigerellleire m de 5 A A O A esc sas cae a eae Stacia scien Se sevens aay Shanda 5 OSC UO Meise ten si cera heen eri cnt T MM 5 Ba nye as E AE E ENEY BA EE TERETA VE EE coh d ducc du us t LU i dii 6 NO p E eT 7 A ui eee ere 7 Use nena c MIN NN ET 7 Fuse Replacement LI AGQKANN EDU T em 7 Ao AP ue eee 8 Batten RUM TINO Mn c D E 8 Setting he LISI DUO s asccumes A PP A 8 OTC o O OUT NM 9 SO A Ur EH 9 miele ME NE E m EM 9 4 ODeFalloli iei ss 10 ControlPanel OPEN stas ia aaa 10 Ment MA e ata de o eta nto dd ee o o eS 10 A A AN 11 o Reet et ne I te ee nee eee 11 MAS ESO V1 0 6 ani rns ie tener TORTE E TRES 11 DMA PCRS OM ANS RENTE dd is 11 DRM 2 4 GHz DMX Mode Mantel SY MC ad A estoit cruce Ac 12 DF 2 4 GHZ DMX Mod Auto SYNC Janasa a a
9. H Channel 1 NIOO AJOJN 6 CH Channel oO o1 RR WO NY Function Value Setting Auto and Sound 061U 120 Auto program 2 Programs 1210 180 Auto program 3 181 U 240 Auto program 4 241 0 Auto Speed when Channel 10 000 240 Sound Sensitivity when Channel 10 is 241 255 0000 010 No function 011 060 Auto program 1 255 Sound Active mode 000 U 255 Program speed slow to fast 000 010 No function 011 U 255 Sound sensitivity low to high 000 U 051 Preset dimmer speed set in menu options 052U 101 Dimmer speed mode off Dimmer Mode 102U 152 Dimmer speed mode 1 fast speed 153U 203 Dimmer speed mode 2 medium speed 2040 255 Dimmer speed mode 3 slow speed Function Value Percent Setting 0000 255 0 100956 0000 255 0 100 0000 255 0 100 0000 255 0 100956 0000 255 0 100 White 0000 255 0 100 U 0000 255 0 100 000 U 010 No function Strobe z 011 U 255 Slow to fast Function Value Percent Setting 0000 255 0 100956 0000 255 0 100956 0000 255 0 100 0000 255 0 100 0000 255 0 100956 0000 255 0 100 White c lt Freedom Par Hex 4 User Manual Rev 2 Page 15 of 21 Configuration Standalone D Sound Active Mode Sound Sensitivity Auto Programs Program Speed Selecting the Dimmer Speed Mode Static Colors Custom Color Mixing Page 16 of 21 Use standalone configuration to operate the product without a DMX controller Ther
10. P X Sound Activated Replaceable Fuse DMX User Serviceable Master Slave Safety Notes These notes include important information about the mounting usage and maintenance of this product read before using the product Always connect the product to a grounded circuit to avoid the risk of electrocution Always disconnect the product from the power source before cleaning or replacing the fuse Avoid direct eye exposure to the light source while the product is on Make sure the power cord is not crimped or damaged Never disconnect the product from power by pulling or tugging on the cord If mounting the product overhead always secure to a fastening device using a safety cable Make sure there are no flammable materials close to the product when operating Do not touch the product s housing when operating because it may be very hot Always make sure that the voltage of the outlet to which you are connecting the product is within the range stated on the decal or rear panel of the product The product is for indoor use only IP20 To prevent risk of fire or shock do not expose the product to rain or moisture Always install the product in a location with adequate ventilation at least 20 in 50 cm from adjacent surfaces Be sure that no ventilation slots on the product s housing are blocked Never connect the product to a dimmer D Make sure to replace the fuse with another of the same type and rating Never carry the product from
11. Power Charging the Battery D Battery Life Indicator Battery Run Time Setting the Limiter Option Page 8 of 21 Daisy chaining products together through their Power In and Power Out sockets called power linking allows many products to be powered from one power outlet Up to 26 Freedom Par Hex 4 products can be power linked at 120 V and up to 50 Freedom Par Hex 4 products can be power linked at 230 V The Freedom Par Hex 4 comes with a rechargeable lithium battery for cable free operation The battery charges whenever the product is plugged into a power source If the product is plugged in and not in operation make sure the On Off switch is in the Off position For optimal battery life charge the Freedom Par Hex 4 battery for 24 hours prior to initial use The battery life indicators are the 4 small green LEDs on either side of the D Fi M lt AUTO gt button The indicators show how much battery life remains available The diagram below provides a key to reading the battery life indicators D Fi AUTO Button The Freedom Par Hex 4 has a limiter option that decreases the power output and extends battery life when more than 4 colors are turned on This option is set in the control panel Note The battery times listed below assume that the limiter option is enabled Maximum Run Time Maximum Run Time all colors on single color on Recharge Time Up to 8 hours Up to 20 hours 6 hours To select wheth
12. e a claim with Chauvet within 7 days of delivery See Contact Us Text Convention Meaning Conventions 1 512 A range of values 50 60 A set of values of which only one can be chosen Settings A menu option not to be modified Menu Settings A sequence of menu options to be followed lt Enter gt A key to be pressed on the product s control panel ON A value to be entered or selected Sym bols Symbol Meaning Critical installation configuration or operation information Not following these instructions may make the product not work cause damage to the product or cause harm to the operator Important installation or configuration information The product may not function correctly if this information is not used Useful information Disclaimer The information and specifications contained in this User Manual are subject to change without notice Chauvet assumes no responsibility or liability for any errors or omissions and reserves the right to revise or recreate this manual at any time The latest version of this manual can be downloaded from http www chauvetlighting com product manuals literature O Copyright 2015 Chauvet All rights reserved Electronically published by Chauvet in the United States of America Author Date Editor Date M Trouard 01 30 2015 A Leon 02 11 15 Freedom Par Hex 4 User Manual Rev 2 Page 3 of 21 Auto Program Product at a Use on Dimmer P Glance outdoor Use Auto Ranging Power Supply P
13. e are a variety of Standalone modes and they are powerful tools for making exciting looks Never connect a product operating in a standalone mode Static Sound Active Auto or Infrared to a DMX chain that includes a DMX controller Products in a standalone mode can transmit DMX signals that interfere with the DMX signals from the controller Sound Active mode sets the product to respond to sounds and music To enable the Sound Active mode do the following 1 Press MENU repeatedly until Snd shows on the display 2 Press ENTER To set the sound sensitivity follow the instructions below 5 Press lt MENU gt repeatedly until SenS shows on the display 6 Use UP or DOWN to select the desired sound sensitivity u 0 u100 low to high 7 Press ENTER The product will respond only to low frequencies of music bass and drums If the product is not responding to sound increase the sensitivity Auto programs set the product to 1 of 4 preset color programs To set the product to an auto program do the following 1 Press lt MENU gt repeatedly until P shows on the display 2 Press ENTER and P 1 P 4 shows on the display 3 Use UP or DOWN to select the desired auto program P 1 P 4 4 Press ENTER To set the auto program speed follow the instructions below 1 Press lt MENU gt repeatedly until S shows on the display 2 Use UP or DOWN to select the desired auto program speed S
14. e shipping the product Be prepared to provide the model number serial number and a brief description of the cause for the return You must send the merchandise prepaid in its original box and with its original packing and accessories Chauvet will not issue call tags Clearly label the package with the RMA number Chauvet will refuse any product returned without an RMA number Write the RMA number on a properly affixed label DO NOT write the RMA number directly on the box Before sending the product clearly write the following information on a piece of paper and place it inside the box Your name Your address Your phone number RMA number A brief description of the problem Be sure to pack the product properly Any shipping damage resulting from inadequate packaging will be your responsibility FedEx packing or double boxing is recommended Chauvetreserves the right to use its own discretion to repair or replace returned product s Page 20 of 21 Freedom Par Hex 4 User Manual Rev 2 CONTACT Us WORLD HEADQUARTERS Chauvet General Information Technical Support Address 5200 NW 108th Avenue Voice 954 577 4455 Press 4 Sunrise FL 33351 Fax 954 756 8015 Voice 954 577 4455 Email tech 2chauvetlighting com Fax 954 929 5560 Toll free 800 762 1084 World Wide Web www chauvetlighting com UNITED KINGDOM AND IRELAND Chauvet Europe Ltd General Information Technical Support Address Unit 1C Email
15. er allow wireless Master Slave control of up to 32 Freedom Par Hex 4s The Freedom Par Hex 4 can also be controlled with a D Fi compatible controller such as the Obey 40 D Fi Freedom Par Hex 4 User Manual Rev 2 Page 5 of 21 Dimensions Page 6 of 21 Freedom Par Hex 4 User Manual Rev 2 3 SETUP The Freedom Par Hex 4 has an internal auto ranging power supply and it can work with an input voltage AC Power range of 100 to 240 VAC 50 60 Hz N Always connect the product to a protected circuit circuit breaker or fuse Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire D Never connect the product to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel serves only as a 0 to 100 switch Disconnect the product from power Wedge the tip of a flat head screwdriver into the slot of the fuse holder Pry the fuse holder out of the housing Remove the blown fuse from the holder Replace with a fuse of the exact same type and rating Insert the fuse holder back in place and reconnect power Fuse Replacement SE a N Disconnect the product from power before replacing the fuse Installed Fuse d held by plastic clip a Safety I E Cap Fuse Replacement Spare Fuse Diagram holder inside safety cap Freedom Par Hex 4 User Manual Rev 2 Page 7 of 21 Power Linking D Battery
16. er the limiter is on or off follow the instructions below Press lt MENU gt repeatedly until Limi shows on the display Press ENTER and On activates limiter or OFF deactivates limiter shows on the display Use UP or DOWN to select the desired option Press ENTER mue Freedom Par Hex 4 User Manual Rev 2 Mou nting Before mounting the product read and follow the safety recommendations indicated in Safety Notes Orientation The Freedom Par Hex 4 has a compact design to fit perfectly inside the TRUSST truss systems It attaches to 35 50 mm truss without the need for a bracket using an M12 threaded rigging point Floor mounting is a cinch with a built in adjustable kickstand The product may be mounted in any position however place the product so there is at least 20 of space around it and it is accessible for programming and control panel operation Rigging Rig the product from a structure or surface that can support the products weight See Technical Specifications in this manual for the product s weight When mounting the product overhead always use a mounting clamp and safety cable Mount the product securely to a rigging point such as a pipe or truss The CHAUVET CH 05 safety cable is appropriate for this product When rigging the product onto a truss you should use a mounting clamp of appropriate weight capacity The Freedom Par Hex 4 has an M12 threaded mounting hole which is appropriate for this p
17. ess MANUAL on the IRC 6 2 Press any number between 0 and 9 to choose your color To manually control the RGBAW UV percentage 1 Press lt MANUALS on the IRC 6 2 Press R5 lt G gt lt B gt lt A gt W or lt UV gt red green blue amber white or ultraviolet to choose your color 3 Press lt gt or to increase or decrease the percentage of each color Miscellaneous Operation To adjust the strobe rate of the program 1 Press lt STROBE gt on the IRC 6 2 Press lt gt or lt gt to increase or decrease the strobe rate 3 Press lt STROBE gt again to turn off the strobe To choose a fade auto program Press lt FADE gt repeatedly on the IRC 6 to choose between the two auto program fade options To black out the lights Press BLACK OUT gt on the IRC 6 This will turn off all the lights until the button is pressed again TL M H __ Mm oo Gecooo6e008 LOOODOE 9Ge9e9ooe owe Note The IRC 6 will not respond to any inputs when the Black Out mode is activated If the remote does not respond when a button is pressed try pressing BLACK OUT gt You may have inadvertently activated the Black Out mode Freedom Par Hex 4 User Manual Rev 2 Page 17 of 21 5 TECHNICAL INFORMATION Product Dust build up reduces light output performance and can cause overheating This can lead to reduction of the light s
18. first product slave to DMX In of the next product slave Continue connecting each subsequent product until all the products are part of the chain Information about DMX is in the DMX Primer which is available from the Chauvet website www chauvetlighting com download When DMX linking Freedom Par Hex 4 products for Master Slave operation the DMX controller is not a part of the DMX daisy chain and the master is the first product in the chain See Master Slave Mode for details To ensure full access to all channels in each DMX mode the highest recommended DMX address is 501 Master Slave mode allows a single Freedom Par Hex 4 the master to control the actions of one or more Freedom Par Hex 4 units the slaves without a DMX controller The master will be set to operate in either an auto program or Sound Active mode while the slaves will be set to DMX starting address d 1 Once set and connected the slaves will operate in unison with the master Configure the units as indicated below Slaves Press MENU repeatedly until any DMX personality shows on the display Press ENTER to accept Set the DMX address to d 1 Connect the DMX input of the first slave to the DMX output of the master Connect the DMX input of the subsequent slaves to the DMX output of the previous slave Finish setting and connecting all the slaves aster Set the master to operate in either an auto program or Sound Active mode Make the master the fir
19. ource s life To maintain optimum performance and minimize wear clean the product at least Maintenance twice a month However usage and environmental conditions may require more frequent cleaning To clean the product follow the instructions below 1 Unplug the product from power 2 Wait until the product is at room temperature 3 Use a vacuum or dry compressed air and a soft brush to remove dust collected on the external surfaces and vents 4 Clean all external optics and transparent surfaces with a mild soap solution ammonia free glass cleaner or isopropyl alcohol 5 Apply the solution directly to a soft lint free cotton cloth or a lens cleaning tissue 6 Softly wipe any dirt or grime to the outside edges of the external optics or transparent surface 7 Gently polish the external optics and transparent surfaces until they are free of haze and lint D Always dry the lens surfaces carefully after cleaning them Page 18 of 21 Freedom Par Hex 4 User Manual Rev 2 6 TECHNICAL SPECIFICATIONS Dimensions and Weight Power LED Photometrics Thermal DMX Ordering Freedom Par Hex 4 User Manual Rev 2 Weight 6 2 Ib 2 9 kg Width Height 5 7 in 145 mm 7 2 in 184 mm Note Dimensions in inches rounded to the nearest decimal digit Length 5 4 in 138 mm Range Voltage Selection 100 240 VAC 50 60 Hz Input Voltage Switching internal Auto ranging Parameter 120 VAC 60 Hz 230 VAC 50 Hz
20. st unit in the DMX daisy chain Configure all the slaves to Slave mode before connecting the master to the DMX daisy chain Never connect a DMX controller to a DMX daisy chain of master and slaves Make the master the first unit in the DMX daisy chain Always put the male DMX connector DMX Out into the master DO NOT connect more than 31 slaves to the master using DMX cable When selecting a starting DMX address always consider the number of DMX channels the selected DMX mode uses If you choose a starting address that is too high you could restrict the access to some of the product s channels NS HIS I Ic If unfamiliar with DMX download the DMX Primer from www chauvetlighting com To select the DMX personality and starting address do the following 1 Press lt MENU gt repeatedly until 6 CH 6 channel mode 8 CH 8 channel mode or 12CH 12 channel mode shows on the display Press ENTER and d 1 d512 shows on the display 2 3 Use UP or DOWN to select the starting address 4 Press ENTER Page 11 of 21 D Fi M 2 4 GHz The Freedom Par Hex 4 series offers wireless control of 2 or more products with a single DMX DMX Mode controller To manually set up the D Fi 2 4 GHz syncing for DMX do the following For the transmitting product 1 Press lt MENU gt repeatedly until S tr shows on the display Press ENTER Press UP or DOWN until dtCH appears on the display Press ENTER Use UP or
21. t to various modes adjust the color soeed and sensitivity and set the strobe The Freedom Par Hex 4 is compatible with the included IRC 6 from Chauvet To enable use with the IRC 6 follow the instructions below 1 Press MENU repeatedly until SET shows on the display 2 Press ENTER and On turns on the infrared sensor or OFF turns off the infrared sensor shows on the display 3 Press UP or DOWN to select the desired option 4 Press ENTER IRC 6 Operations Be sure the IRC 6 remote is pointing directly at the product and there is nothing in between the remote and the product UN Automatic Mode Automatic mode will enable you to run the automatic programs on the product on To turn on Automatic mode 1 Press AUTO on the IRC 6 2 Press lt gt or to choose between the four different auto programs To adjust the speed of the automatic program 1 Press lt SPEED gt on the IRC 6 2 Press 96 3 Press lt gt or lt gt to either increase or decrease the speed of the program Sound Active Mode Sound Active mode will enable the product to respond to the music To turn on Sound Active mode Press SOUND on the IRC 6 To adjust sound sensitivity in Sound Active mode 1 Press lt SENSITIVITY gt on the IRC 6 2 Press 96 3 Press lt gt or lt gt to either increase or decrease sound sensitivity Manual Color Control To choose a specific color with the IRC 6 1 Pr
22. the power cord The maximum ambient temperature Ta is 104 F 40 C Do not operate the product at higher temperatures In the event of a serious operating problem stop using the product immediately Never try to repair the product Repairs carried out by unskilled people can lead to damage or malfunction Contact the nearest authorized technical assistance center This product is not intended for permanent installation To eliminate unnecessary wear and improve its lifespan during periods of non use completely disconnect the product from power via breaker or by unplugging it Keep this User Manual for future use If you sell the product to another user be sure to give this document to the next owner Page 4 of 21 Freedom Par Hex 4 User Manual Rev 2 2 INTRODUCTION On Off Switch Kickstand Infrared Sensor DMX Out Carry Handle DMX In Glare Shield Menu Buttons Overview Microphone Fuse Holder Display Battery Life Indicator LEDs Power In Power Out D Fi AUTO Sync Clear Button Description The Freedom Par Hex 4 is a wireless battery operated hex color LED wash fixture It can be used as an uplight on the floor or suspended overhead It has a compact design that works with TRUSST and an adjustable kickstand for easy floor placement The RGBAW UV LEDs allow for infinite color mixing with the added punch of ultra violet light The built in wireless D Fi transmitter and receiv
23. tivity SeS ET Sets sound sensitivity low to high Red 0 100 Green 0 100 Blue 0 100 Amber 0 100 W 0 W255 White 0 100 UV 0 100 aM Sets the dimming speed mode dIM1 fast to Custom Color Mixing ames stow or OFF drAS drAU Automatically select receive frequency i drCH dri dri6 Manually select receive frequency 2 4 GHz D Fi dtAS dtAU Automatically select transmit frequency dtCH dt 1 dt16 Manually select transmit frequency oon E On Turns limiter on enabling extended battery life Limiter Limi Off Turns limiter off disabling extended battery life Page 10 of 21 Freedom Par Hex 4 User Manual Rev 2 DMX Linking D Starting Address Master Slave Mode D DMX Personalities Freedom Par Hex 4 User Manual Rev 2 The Freedom Par Hex 4 operates in Master Slave mode or in DMX mode both of which require DMX linking In Master Slave mode the master product sends DMX signals to the slaves In DMX mode the lighting control board sends DMX signals to the products To DMX link a number of Freedom Par Hex 4 using wireless D Fi M see D Fi 2 4 GHz DMX Mode Manual Sync To DMX link a number of Freedom Par Hex 4 using DMX cable connect the DMX cable from DMX Out of the board to DMX In of the first product or connect the DMX cable from DMX Out of the master to DMX In of the first slave Then connect another DMX cable from DMX Out of the
24. urpose For the Chauvet line of mounting clamps go to www chauvetlighting com cables clamps main html When mounting the product on the floor make sure that the product and any cables are away from people and vehicles Mounting Clamp fer such as the CLP 15 clamp Threaded Mounting e ev Y d from Chauvet Hole Size M12 Mounting Hr Diagram Mm Safety Cable such as CH 05 from Chauvet Freedom M Par Hex 4 User Manual Rev 2 Page 9 of 21 4 OPERATION Control Panel access the control panel functions use the buttons located underneath the display Operation Button Function lt MENU gt Selects an operation mode lt UP gt Scrolls up the list of options or selects a higher value lt DOWN gt Scrolls down the list of options or selects a lower value lt ENTER gt Activates a menu option or a selected value lt AUTO gt Auto syncs D Fi or displays information about D Fi status Menu Map The Menu Map outlines the functions available through the menu the programming levels that can be entered and a description for each function Main Function Programming Levels Description DMX Personality and Starting Address 8 BCH Selects DMX personality and DMX starting value m Static Colors C 1 C 63 Selects 1 of 63 static colors Auto Programs o trea Selects 1 of 4 auto programs Program Speed S1 S00 Sets auto program speed slow to fast Sound Active ass Selects Sound Active mode Sound Sensi
Download Pdf Manuals
Related Search