User`s Manual
Contents
1. Status Indications LED Indicators Status Red LED Green LED Normal state Flash Valid card Light Invalid card Light Open Light Key Press Light Program Mode Light Flash frequent Set OK Light Light Alarm Flash Buzzer Status Description Buzz Valid card Two short beeps BiBi Invalid card Long beep once pim Key Press Short beep once Bi Input valid Two short beeps BiBi password Input wrong Long beep once Bi password Alarm state Continuous long beeps Bi Bi Bi 4 Setup 1 Default value Login password 9999 User password 1234 2 Enter programming mode Press Login password enter programming mode 3 Function setup should be in programming mode 1 Modify login password Press 0 new password confirm new password Note the new password should be any 4 8 figures 2 Add user card Press 1 read card Input code Note the code should be three figures from 001 to 500 which should not duplicate The code must be input otherwise the card will be invalid If add more than one cards three digit code is put in before pressing 3 Delete user card three ways A Press B Press read the second card directly after the first 2 ojojoj 0 to delete all user2. ON position Power on Shift the jumper switch back to OFF position after three beeps of the buzzer now the factory setting is restored Attachment wiring diagram for installation pp e GND OPEN aon DOOR_IN 220VMA z PUSHIN O e N C TA A PUSH r GND GND 12VDC j 12V lenrs 2 mit 3 RNR MRED 4 RNB AMRA RRMAGARS ats 3 082 gt 6 RRMA 3 2 7 ii az 8 i2vim 9 mnie 10 ene NOTE 1 Power off before installation wiring hot line work is forbidden 2 Normally electrolock is connected out from power controller
3. cards 2 read card to delete the corresponding card C Press 2 input code to delete lost card 4 Set open mode Press 3 0 0 by valid card only Press 3 0 1 by valid card and password Press 3 0 2 by valid card or password Note factory setting is valid card Since the initial password can not be used to open door If set to valid card or password mode password for use should be modified 5 Set the length of open time Press 4 X Note XX is from 00 99 unit is second factory setting is 6 seconds 6 Set the length of alarm time Press 5 X Note XX is from 00 99 unit is minute factory setting is 3 minutes 7 Set door state monitoring mode Press 6 0 0 to disable this function Press 6 oju to enable this function Note to enable door state monitoring reed switches must be installed when this function is enabled the following two functions can also be enabled at the same time A If the user put in the correct password to open the door then forget to close the door the buzzer will give audible sound to note the user B If the door is opened illegally the system will activate alarm signal output at the same time buzzer emits sound alarm 8 Set safety mode Press 7 0 10 to disable this function Press 7 O
4. RFID Access Control System User s Manual Please read this manual thoroughly before installation 1 Brief Product Introduction This product is RFID access control system which is currently one of the advanced ac systems It uses the latest central process unit CPU and memory chip of large capacity There will be of no information loss even in case of power failure It takes the latest HOMMARD technology with strong power of three ways to open door open by card read open by card read adding with password and open by password The perfect security functions let the users feel much more safe which include door state monitoring alarm output safety mode anti dismantling RFID card and password While its functions of opening button close notification door bell to be connected with NO and NC locks bring more operating easiness to the users This product provides access control mode which is safe and fully automatic it is an ideal device for business organizations offices factories residences and communities 2 Technical Features No Item Specification Power supply DC Voltage 12V 10 current lt 0 1A 2 Max load Alarm output 100mA Electrolock output 5A B Dimension 116mm X 116mm X 20mm Weight 180g 5 Ambient temp 20 C 60 C 6 RH 20 90 Memory capacity Information of 500 user card and 500 passwords Induction distance 5 15CM Car type EM or EM compatible card
5. j il to read 10 invalid cards or valid cards then enter 4 wrong passwords successively the system is locked for 10 minutes Press 7 ol E to read 10 invalid cards or valid cards then enter 4 wrong passwords successively the system activates alarm signal output Note factory setting this function is disabled 9 Save the settings and exit programming mode Press Note Jshould be pressed within 1 minute to save the setting when any of the above operation is completed Modify user password no need in programming mode after pressing to read user card the green LED flashes input user password then press to enter password modifying mode Now input new password of 4 figures press and input the new password again press to save the setting How to use 1 In normal work mode can be open by one valid card 2 When valid card and password mode can be open if the correct password is put in within 10 seconds after card swiping 3 If the password of a card is forgotten the information of this card in the system should be deleted first then add this card to the system again to modify the password 4 If program password is forgotten you can use jumper switch RESET at the main board to restore factory setting First power off Then set jumper switch to
Download Pdf Manuals
Related Search