Technical Manual Of Intel Haswell / Broadwell
Contents
1. Serial Port FIFO Mode The optional settings 16 Byte FIFO 32 Byte FIFO 64 Byte FIFO 128 Byte FIFO ERP Function The optional settings Disabled Enabled This item should be set as Disabled if you wish to have all active wake up functions Case Open Detect This item controls detect case open function The optional settings are Enabled Disabled WatchDog Reset Timer Use this item to enable or disable WatchDog Timer reset function When set as Enabled the following sub items shall appear WatchDog Reset Timer Value User can set a value in the range of 10 to 255 WatchDog Timer Unit The optional settings are Sec Min 25 WatchDog Wake up Timer Use this item to enable or disable WatchDog Timer Wake up function When set as Enabled the following sub items shall appear WatchDog Wake up Timer Value in ERP User can select a value in the range of 10 to 4095 seconds when WatchDog Timer Unit in ERP set as Sec or in the range of 1 to 4095 minutes when WatchDog Timer Unit in ERP set as Min WatchDog Timer Unit The optional settings are Sec Min ATX Power Emulate AT Power This item support Emulate AT power function MB power On Off control by power supply User needs to select AT or ATX Mode on MB jumper at first ATX Mode amp AT Mode Select PC Health Status Press Enter to view current hardware health status amp make further setting2. Auto Gen2 Gen 1 PCH LAN Controller For user to enable or disable onboard NIC The optional settings are Enabled Disabled When set as Enabled user can make further settings in Wake on LAN Use this item to enable or disable integrated LAN to wake the system The Wake On LAN cannot be disabled if ME is on at Sx state Audio Controller Use this item to control the detection of the Azalia HD Audio device The optional settings are Disabled Enabled Disabled Azalia will be unconditionally disabled Enabled Azalia will be unconditionally enabled USB Devices Configuration Press Enter to further setting USB device configuration USB Confiquration Mode Use this item to control the USB XHCI controller The optional settings are Smart Auto Auto Enabled Disabled Note When set as Disabled user can make further settings in EHCI1 Use this item to control the USB EHCI USB 2 0 functions One EHCI controller must always be enabled The optional settings are Disabled Enabled Restore AC Power Loss Use this item to select AC power state when ACpower is re applied after a power failure The optional settings are Always On Always Off Former State On and Former State options are affected by ERP function Please disable ERP to support Always On and Former State 3 9 Security Menu Utility Copyright C 2015 American Hegatren
3. KEEEEIFEEEERE 9 1 2 Open Normal Defualt L 1 2 Closed Case Open Function Selected One Touch Pin 1 2 Closed When cu open function pin short to GND the Case open function was detected When Used needs to enter BIOS and enable Case Open Detect function In this case if your case is removed next time when you restart your computer a message will be displayed on screen to inform you of this ME UNLOCK tiia Flash Y Security Override Select 5 1 2 Open Enable Security Measures in the Flash Descriptor Default LL 1 2 Closed Disable Security Measures in the Flash Descriptor Override ME UNLOCK 2 2 Connectors and Headers 2 2 1 Connectors Rear IO Panel Diagram RJ 45 LAN Port HDMI Ports USB 3 0 Ports 9V 24V DC Power in Connector Line OUT Optical SPDIF OUT Front IO Panel Diagram USB 3 0 Port ese Clear CMOS Button This connector is standard RJ 45 LAN jack for Network connection To connect USB keyboard mouse or other devices USB 3 0 Port compatible with USB specification USB 3 0 ports supports up to 5Gbps data transfer rate HDMI Port To connect display device that support HDMI specification For user to connect external speaker earphones Line Out Connector etc to transfer system audio output Optical SPDIF Out This connector can function as optical SPDIF Out Connector jack with compatible cables amp devices 9V 24V DC_IN SATA 7 pin Blo
4. SATA Port The optional settings are Enabled Disabled SATA Device Type The optional settings are Hard Disk Driver Solid State Drive Use this item to identify the SATA port is connected to Solid State Drive or Hard Disk Drive m SATA mSATA The optional settings are Disabled Enabled Intel R Rapid Start Technology Press Enter to go Intel R Rapid Start Technology screen to make further settings Intel R Rapid Start Technology The optional settings Disabled Enabled When set as Enabled the following sub items shall appear Entry on 53 RTC Wake Use this item to enable or disable RapidStart invocation upon S3 RTC wake The optional settings are Disabled Enabled When set as Enabled the following sub items shall appear Entry After Use this item to enable RTC wake timer at S3 entry Value ranges from 0 Immediately to 120 minutes Active Page Threshold Support The optional settings are Disabled Enabled Network Stack Configuration Press Enter to go to Network Stack screen to make further settings Network Stack Use this item to enable or disable UEFI Network Stack The optional settings are Enabled Disabled When set as Enabled the following sub items shall appear 4 PXE Support The optional settings are Disabled Enabled Use this item to enable 4 PXE Boot Support When set as Disabled 4 boot option will n
5. ALME Iz il oc ae E eae 12 CHAPTER 3 INTRODUCING BIOS 31 ENTERING SETUP cossin e Ea aeaea Eleg 16 32 BIOS MENUSCREEN E er ege 17 3 3 FUNCTION gi 2lc M 18 34 GETTING HEE eo t 18 39 MEMU BAR nnnm 19 3 6 MAIN MENU 20 ADVANCED MENU p aE E 21 CHIPSET l5 E 32 35 340 BOOT 36 3 11 SAVE amp EXIT MENU 37 iii caurion Environmental Safety Instruction Avoid the dusty humidity and temperature extremes Do not place the product in any area where it may become wet 0 to 60 centigrade is the suitable temperature The figure comes from the request of the main chipset Generally speaking dramatic changes in temperature may lead to contact malfunction and crackles due to constant thermal expansion and contraction from the welding spots that connect components and PCB Computer should go through an adaptive phase before it boots when it is moved from a cold environment to a warmer one to avoid condensation phenomenon These water drops attached on PCB or the surface of the components can bring about phenomena as minor as computer instability resulted from corrosion and oxidation
6. from components and PCB or as major as short circuit that can burn the components Suggest starting the computer until the temperature goes up The increasing temperature of the capacitor may decrease the life of computer Using the close case may decrease the life of other device because the higher temperature in the inner of the case Attention to the heat sink when you over clocking The higher temperature may decrease the life of the device and burned the capacitor iv USER S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER NO PART OF THIS MANUAL INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER BOARD SERIES AND WE DO ASSURE THIS MANUAL MEETS USER S REQUIREMENT BUT WILL CHANGE CORRECT ANY TIME WITHOUT NOTICE MANUFACTURER PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND AND WILL NOT BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTIAL OR CONSEQUENTIAL DAMAGES INCLUDING DAMANGES FOR LOSS OF PROFIT LOSS OF BUSINESS LOSS OF USE OF DATA INTERRUPTION OF BUSINESS AND THE LIKE PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER S BENEFIT WITHO
7. Bc Save gt Sustem Age system Agent SA Parameters F PCH IO pant igurat ion Select Screen Ti Select Item Enter Select Change Opt F1 2n eral E Pi evious Values F3 Optim idi Defaults Fd Save B it ESC Exit Version 2 17 1246 Copyright C 2015 American NEvatrercs Inc gt System Agent SA Configuration Press Enter to make settings for the following sub items VT d The optional settings are Enabled Disabled This item might not be available depending on configuration gt Graphics Configuration Press Enter to make further settings for Graphics Configuration Graphics Configuration Aperture Size The optional settings are 128MB 256MB 512MB DVMT Pre Allocated Use this item to select DVMT 5 0 pre allocated fixed graphics memory size used by the internal graphics device The optional settings are 32M 64M 96M 128M 160M 192M 224M 256M 288M 320M 352M 384M 416M 448M 480M 512M DVMT Total Gfx Mem Use this item to select DVMT 5 0 total graphics memory size used by the internal graphics device The optional settings are 128M 256M MAX Memory Configuration Press Enter to view current memory configuration Configuration Press Enter to make settings for the following sub items Mini PCIE The optional settings are Enabled Disabled Mini PCIE Speed The optional settings are
8. Built in EFI Shell xx Press this item to select the device as boot disk after save configuration and reset Lauch EFI Shell from filesystem device Use this item to launch EFI shell application shell efi from one of the available filesystem device
9. Dynamic Time Use this item to enable or disable system wake up by RTC alarm The optional settings Disabled Enabled When set as Enabled system will wake on the current time increased minute s UABO 1 Wake up from 53 54 The optional settings Enabled Disabled 29 Note USB Wake up is affected by ERP function in S4 Please disable ERP before activating this function in S4 USB Configuration Press Enter to make settings for the following sub items USB Configuration Legacy USB Support The optional settings are Enabled Disabled Auto Enabled To enable legacy USB support Disabled To keep USB devices available only for EFI specification Auto To disable legacy support if no USB devices are connected XHCI Hand off This is a workaround for OSes without XHCI hand off support The XHCI ownership change should be claimed by XHCI driver The optional settings are Enabled Disabled EHCI Hand off This is a workaround for OSes without EHCI hand off support The EHCI ownership change should be claimed by EHCI driver The optional settings are Disabled Enabled USB Mass Storage Driver Support The optional settings are Disabled Enabled USB hardware delay and time outs USB Transfer Time out Use this item to set the time out value for control bulk and interrupt transfers The optional settings are 1 sec 5 sec 10 sec 20 sec Device Reset Time out Use this
10. Technical Manual Of Intel Haswell Broadwell Series CPU Based SBC NO G03 NU92 F Revision 1 0 Release date 14 2015 Trademark Specifications and Information contained in this documentation are furnished for information use only and are subject to change at any time without notice and should not be construed as a commitment by manufacturer Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding To minimize pollution and ensure environment protection of mother earth please recycle li TABLE OF CONTENT ENVIRONMENTAL SAFETY Iv USER S NOTICE LEE t V MANUAL REVISION nnn nnn nnns V GS FG cy CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD 1 1 FEATURE OF 2 ss etesensvsearieaetienneteieeaveennae 1 1 2 SPECIFICATION 2 1 3 LAYOUT DIAGRAM 3 CHAPTER 2 HARDWARE INSTALLATION 2 4 JUMPER SETTING sericea cee LEDE 7 2 2 CONNECTORS AND HEADERS wesitecencccnneetesdscewveshanectestencanseceestecdawebuseduninceseneecwaceee 9 CONNECTORS c a inince 9
11. UT INTENT TO INFRINGE Manual Revision Information Reversion Revision History Date 1 0 First Edition May 14 2015 Item Checklist Motherboard User s Manual DVD for motherboard utilities Cable s Chapter 1 Introduction of the Motherboard Feature of Motherboard Onboard Intel Haswell U Broadwell U Series Processor with low power consumption never denies high performance Support 2 DDR3L 1333 1600Mhz dual channel SO DIMM max up to 16GB Onboard 1 mSATA slot Onboard 1 half size Mini PCIE slot Onboard gigabit Ethernet LAN port Support dual HDMI outputs Support USB 3 0 data transport demand Support CPU Smart FAN Compliance with ErP standard Support Watchdog function Support DC 9V 24V wide range power input 1 2 Specification Spec _ Description 2020 Design 9 8 SBC PCB size 10 1 cm x 10 1 cm Embedded CPU Integrated with Intel Haswell U Broadwell U series SoC CPU e 2 DDR3L SODIMM Slot for un buffered Single Channel DDR3L 1333 1600 MHz SDRAM expandable to 16GB Memory Slot Support dual channel function Please refer to the actual product you purchase and consult your dealer for more information Expansion Slot e 1 Half size Mini PCIE slot o St 1 SATAIII 6Gb s port orage e 1 MSATA slot e Integrated with Intel i218LM Gigabit LAN chip LAN Chip Support Fast Ethernet LAN function of providing 10 100 1000Mbps Ethernet data transfer rate Audio Chi
12. ate elements System Time Set the time Please use Tab to switch between time elements 3 7 Advanced Menu 10 Setup Utility Copyright C 2015 American Megatrends Inc E Advanced BETTE tu Save 2 Exit 7 Cont CPU Configuration Parameters Trusted Comput ing ACPI Settings Configuration Configuration Super Configuration PC Health Status SATA Configuration Intel R Rapid Start Technology Network Stack Configuration CSM Configuration Hake up Function Settings USB Configuration H Select Screen Intel R Ethernet Connection IZ18 LM 88 88 88 88 87 88 T1 Select Item Driver Health Enter Select t Change Opt F1 General Help Previous Values Optimized Defaults Save 8 Exit ESC Extt Copyright C 2015 American Megatrends Inc CPU Configuration Press Enter to view current CPU configuration and make settings for the following sub items Hyper Threading The optional settings Disabled Enabled Enabled for Windows XP and Linux OS optimized for Hyper Threading Technology Disabled for other OS OS optimized not for Hyper Threading Technology Limit CPUID Maximum The optional settings Disabled Enabled This item should be set as Disabled for Windows XP 21 Execute Disable Bit The optional settings Disabled Enabled Intel Virtualiza
13. ck SATAIII Port connector The board come with a SATAIII port that supports 6GB s transfer rate Pinl es V 2 2 2 Header F USB 9 pin USB 2 0 Port Header m i 2 225 O 0 Pin 1 2 zot amp c zU Jg gt JO gt gt JW 9 pin Front Panel Header HEER o EIE 17 O Pin 1 Da SPEAK CON 4 pin Speaker Header COM 9 pin Serial Port Header EST deb WH eae LIN NEU GND Pin 7 NC CTS NC NC NC NC ND NC NC NC NC Pin1 Un 4 63 Notice User should go to BIOS settings at first to set Transmission Mode Select for COM as RS422 or RS485 refer to Page 25 to support RS422 RS485 function CPUFAN 3 pin CPUFAN Header 3 Fan Detect Chapter 3 Introducing BIOS Notice The BIOS options in this manual are for reference only Different configurations may lead to difference in BIOS screen and BIOS screens in manuals are usually the first BIOS version when the board is released and may be different from your purchased motherboard Users are welcome to download the latest BIOS version form our official website The BIOS is a program located on a Flash Memory on the motherboard This program is a br
14. ds Inc Password Description Set Administrator Password If ONLY the Administrator s password is set then this only limits access to Setup and is only asked for when entering Setup If ONLY the User s password is set then this 15 power password and must be entered to boot or enter Setup In Setup the User will have Administrator rights The password length must be in the following range Minimum length Maximum length 4t Select Screen ti select Item zT Enter Select User Password Change Opt F1 General Help Previous Values Optimized Defaults Save amp Exit ESC Exit Version 2 17 1246 Copyright 2015 American Hezatrends Inc Security menu allow users to change administrator password and user password settings 3 10 Boot Menu Aptio Setup Utility Copyright 2015 American Megatrends Inc Coke SECULI TH lE Boot Configuration Number of seconds to wait for Setup Prompt Timeout setup activation Keu Bootup NumLock State On 65535 means indefinite waiting Quiet Boot Disabled Boot Option Priorities Boot Option 1 UEFI Built in EFI Shell Select Screen TL Select Item Enter Select Change Opt Fl beneral Help Fe Previous Values Optimized Defaults Fd Save Exit ESE EX Version 2 17 1246 Copyright C 2015 American HMegatrends Inc Boot Configuration Setup Prompt Timeout Use this it
15. e the system will enter when the suspend button is pressed The optional settings are Suspend Disabled 53 Suspend to RAM PCH FW Configuration Press Enter to view ME information and make settings in the following sub items gt Firmware Update Configuration Press Enter to make settings for ME FW Image Re Flash ME FW Image Re Flash Use this item to enable or disable ME FW Image Re Flash function The optional settings Disabled Enabled the case that user needs to update ME firmware user should set FW Image Re Flash as Enabled save the settings and exit The system will turn off and reboot after 4 seconds If the user goes to BIOS screen again will find this item is set again as Disabled but user can still re flash to update firmware next time AMT Configuration Use this item to configure Active Management Technology parameters Press Enter to make settings for the following sub items Intel AMT Use this item to enable or disable Intel Active Management Technology BIOS extension The optional settings Disabled Enabled BIOS Hotkey Pressed Use this function to enable or disable BIOS Hotkey Press function 23 MEBx Selection Screen Use this function to enable or disable MEBx Selection Screen function Hide Un Configure ME Confirmation Use this function to enable or disable Hide Un Configure ME without password Configuration Prompt function MEBx Debug Message Ou
16. eader Jumper Jumper Description ME UNLOCK Flash Descriptor Security Override Select 2 Pin Block COPEN Case Open Message Display Function 2 Pin Block Select MODE ATX Mode amp AT Mode Select 2 Pin Block COM Header Pin9 Function Select 4 Pin Block Connectors Connector 2 Name LINE OUT Line Out Connector JSPorOuCamedo __ ___ Internal 9V 24V DC Power in Connector SATA SATA Port Connector SATAPW SATA Power out Connector Headers Header Name Description F USB USB 2 0 Port Header 9 pin Block JW FP Front Panel Header 9 pin Block SPEAK CON Speaker Header 4 pin Block Serial Port Header 9 pin Block LAN LED LAN Activity LED Header 2 Block CPUFAN CPUFAN Header 3 pin Block Chapter 2 Hardware Installation 2 1 Jumper Setting JP1 Header Function Select 1 2 1 2 1 2 3 4 3 4 3 4 5 6 5 6 5 6 2 4 Closed 3 4 Closed 4 6 Closed Pin9 RING Pin9 5V Pin9 DCIN MODE pin LATA amp AT Mode Select 6 MESA EEREEFEEEERE 9 MODE 1 2 Open ATX Mode Selected E 1 2 Closed AT Mode Selected ATX Mode Selected TESS power per to power on after power input ready AT Mode Selected Directly power on as power input ready User needs to restart the system for the settings to take effect COPEN 2 pin Case Message Display Function Select 226 Bi
17. em to set number of seconds to wait for setup activation key Bootup Numlock State Use this item to select keyboard numlock state The optional settings are On Off Quiet Boot The optional settings are Disabled Enabled Boot Option Priorities Boot Option 1 2 The optional settings are UEFI Built in EFI Shell Disabled 36 3 11 Save amp Exit Menu Setup Uti 11119 Copyright C 2015 American Megatrends Inc Save amp Exit 7 and R eset 5 Discard Changes ann Reset Reset the system after saving the changes Restore Defaults Save as User Defaults Restore User Defaults Boot Override UEFI Built in EFI Shell Launch EFI Shell fram Filesustem Device Select Screen Select Item Select Change Opt General Help Previous Values Optimized Defaults Save amp Exit ESC Exit Version 2 17 1246 Copyright 2015 American Hegatrends Inc Save Changes and Reset This item allows user to reset the system after saving the changes Discard Changes and Reset This item allows user to reset the system without saving any changes Restore Defaults Use this item to restore load default values for all the setup options Save as User Defaults Use this item to save the changes done so far as user defaults Restore User Defaults Use this item to restore defaults to all the setup options Boot Override UEFI
18. idge between motherboard and operating system When you start the computer the BIOS program will gain control The BIOS first operates an auto diagnostic test called POST power on self test for all the necessary hardware it detects the entire hardware device and configures the parameters of the hardware synchronization Only when these tasks are completed done it gives up control of the computer to operating system OS Since the BIOS is the only channel for hardware and software to communicate it is the key factor for system stability and in ensuring that your system performance as its best 3 1 Entering Setup Power on the computer and by pressing lt Del gt immediately allows you to enter Setup If the message disappears before your respond and you still wish to enter Setup restart the system to try again by turning it OFF then ON or pressing the RESET button on the system case You may also restart by simultaneously pressing Ctrl lt Alt gt and lt Delete gt keys If you do not press the keys at the correct time and the system does not boot an error message will be displayed and you will again be asked to Press lt Del gt to enter Setup 3 2 BIOS Menu Screen The following diagram show a general BIOS menu screen Menu Bar Rptio Setup UTILITY vopyrignt C 2015 Americin Megatrends Inc Lela eT T I ntormat ian Set the Date Use Tab to BIOS Vendor American Megatrend
19. item to set USB mass storage device start unit command time out The optional settings are 10 sec 20 sec 30 sec 40 sec Device Power up Delay Use this item to set maximum time the device will take before it properly reports itself to the host controller Auto uses default value for a root port it is 100 ms for a hub port the delay is taken from hub descriptor 30 The optional settings Auto Manual Select Manual you can set value for the following sub item Device Power up Delay in Seconds Device Power up Delay in Seconds The delay range is from 1 to 40 seconds in one second increments Intel R Ethernet Connection 1218 LM XX XX XX XX XX XX Press Enter to view current network information and make further settings in NIC Configuration gt NIC Configuration Press Enter to configure the network device port Link Speed Use this item to specify the port speed used for the selected boot protocol The optional settings are Auto Negotiated 10 Mbps Half 10 Mbps Full 10 OMbps Half 100 Mbps Full Wake On LAN Use this item to enable the server to be powered on using an in hand magic packet Blink LEDs Use this item to identify the physical network port by blinking the associated LED Driver Health Press Enter to get driver Health Status information for the drivers controllers 3 8 oppur ieh ce 2015 American Megatrends Inc anc ed chipset Ssecuritu
20. ot be created PXE Support The optional settings are Disabled Enabled Use this item to enable PXE Boot Support When set as Disabled 4 boot optional will not be created PXE boot wait time Use this item to set wait time to press ESC key to abort the PXE boot 28 Media Detect Count Use this item to set number of times presence of media will be checked CSM Configuration Press Enter to make settings for the following sub items Compatibility Support Module Configuration Boot Option Filter This item controls Legacy UEFI ROMs priority The optional settings and Legacy UEFI only Legacy only Network This item controls the execution of UEFI and legacy PXE OpROM The optional settings are Do not launch only Legacy only Storage This item controls the execution of UEFI and Legacy Storage OpROM The optional settings are Do not launch UEFI only Legacy Other PCI devices This item determines OpROM execution policy for devices other than Network storage or video The optional settings are Do not launch UEFI only Legacy Wake up Function Settings Press Enter to make settings for the following sub items Wake up System with Fixed Time Use this item to enable or disable system wake up by RTC alarm The optional settings Disabled Enabled When set as Enabled system will wake on the hour min sec specified Wake up System with
21. p BIOS 9 _ e 1 RJ 45 LAN port e 2 USB 3 0 port Rear Panel I O e 2 HDMI port 1 Audio Line Out SPDIF Out jack e 1 DC 9V 24V power in connector e 1 USB 3 0 port 1 Clear CMOS button e 1 2 Internal 9V 24V power in connector 1 SATA Power connector Internal I O e 1 9 Pin USB 2 0 1 1 header for 2 USB 2 0 1 1 ports e 1 Front panel header 1 SPEAK CON header e 1 LAN LED activity header e 1 serial port header e 1 CPU FAN header 1 5 Layout Diagram Rear IO Panel Diagram RJ 45 LAN Port HDMI Ports USB 3 0 Ports 9V 24V DC Connector Line OUT Optical SPDIF OUT Front IO Panel Diagram USB 3 0 Port ese Clear CMOS Button Internal Diagram Front Side ME UNLOCK SATA Hard Disk USB 2 0 Port Header Power Out Connector SATAII Port Front Panel Header COPEN ar 86 98 Bs sh S ER Clear CMOS Em 4 Button RJ 45 LAN Port Tus o ull size USB 3 0 Port LANLED om Header USB 3 0 Ports cader Half size Mini PCIE Slot zH Serial Port Header lt lt cm COM1 HDMI Ports 0 DDR3L SODIMM Slots SODIMMI 2 Speaker Connector Line Out Optical SPDIF Out H 9 24V DC Power in Connector LI Internal Power Connector Internal Diagram Back Side Power Button CPUFAN H
22. p window that describes the appropriate keys to use and the possible selections for the highlighted item To exit the Help Window press lt Esc gt 3 5 Menu Bars There are six menu bars on top of BIOS screen Main To change system basic configuration Advanced To change system advanced configuration Chipset To change chipset configuration Security Password settings Boot To change boot settings Save amp Exit Save setting loading and exit options User can press the right or left arrow key on the keyboard to switch from menu bar The selected one is highlighted 3 6 Main Menu Main menu screen includes some basic system information Highlight the item and then use the lt gt or lt gt and numerical keyboard keys to select the value you want in each item Aptio Setup Utility Copyright C 2015 American Megatrends Inc Main MENEN Exi Chipset erie pti Boo due BIOS Information set the Date Use Tab to i BIOS Vendor American Megatrends switch between Date elements Core Version 5 010 Filename BARUAADL Build Bate and Time 05 27 2015 17 29 15 Sfi Thu I01 2015 System Time 00 22 48 ACCESS Level Administrator e Select Screen TL Select Item Select Change Opt General Help gt Previous Values Optimized Defaults Save 8 Exit ESC Exit i Version 2 17 1246 Copyright C 2015 American Megatrends Inc System Date Set the date Please use Tab to switch between d
23. s in SmartFAN Configuration amp Shutdown Temperature gt SmartFAN Configuration Press Enter to make settings for SmartFAN Configuration SmartFAN Configuration CPUFAN Smart Mode The optional settings are Disabled Enabled When set as Enabled the following sub items shall appear CPUFAN Full Speed Temperature Use this item to set CPUFAN full speed temperature Fan will run at full speed when above the pre set temperature CPUFAN Full Speed Duty Use this item to set CPUFAN full speed duty Fan will run at full soeed when above the pre set duty CPUFAN Idle Speed Temperature Use this item to set CPUFAN idle speed temperature Fan will run at idle speed when below the pre set temperature CPUFAN Idle Speed Duty Use this item to set CPUFAN idle speed duty Fan will run at idle speed when below the pre set duty Shutdown Temperature Configuration Use this item to select system shutdown temperature The optional settings are Disabled 70 C 156 75 C 164 F 80 172 F 85 C 180 F 90 C 188 SATA Configuration Press Enter to make settings for the following sub items SATA Controller s The optional settings Disabled Enabled SATA Mode Selection The optional settings are AHCI RAID SATA Controller Speed The item is for user to set the maximum speed the SATA controller can support The optional settings are Default Gen1 Gen2 Gen3 SATA Port
24. s switch between Date elements Core Version 5 010 Filename BARUAADL Build Date and Time OS 27 2015 17 29 15 TAU 701720151 System Time 00 22 48 General Help Items ACCESS Level Administrator e Select Screen TL Select Item Enter Select Current Setting Value Change Opt Fi General Help Fe Previous Values Menu Items Function Keys F3 Optimized Default Save 2 Exit Exit sion 2 17 1248 Copuright C 2015 American Hegatrends Inc BIOS Menu Screen 3 5 Function Keys In the above BIOS Setup main menu of you can see several options We will explain these options step by step in the following pages of this chapter but let us first see a short description of the function keys you may use here Press left right to select screen Press TY up down to choose in the main menu the option you want to confirm or to modify Press Enter to select Press lt gt lt gt keys when you want to modify the BIOS parameters for the active option F1 General help F2 Previous value F3 Optimized defaults F4 Save amp Exit Press Esc to quit the BIOS Setup F7 User can press this key to enter Boot Menu when system starts up 3 4 Getting Help Main Menu The on line description of the highlighted setup function is displayed at the top right corner the screen Status Page Setup Menu Option Page Setup Menu Press F1 to pop up a small hel
25. tion Technology The optional settings Enabled Disabled When set as Enabled a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology Hardware Prefetcher The optional settings are Disabled Enabled Use this item to enable or disable the Mid Level Cache L2 streamer prefetcher Adjacent Cache Line Prefetch The optional settings are Disabled Enabled Use this item to enable or disable the Mid Level Cache L2 prefetching of adjacent cache lines EIST Use this item to enable or disable Intel SpeedStep The optional settings are Disabled Enabled CPU C states The optional settings are Disabled Enabled When set as Enabled user can make further settings in the following items CPU C6 Report Use this item to enable or disable CPU C6 ACPI C3 report to OS The optional settings are Disabled Enabled CPU C7 Report Use this item to enable or disable CPU C7 ACPI C3 report to OS The optional settings are Disabled Enabled Trusted Computing Press Enter to make settings to make further settings in Security Device Support Configuration Security Device Support Use this item to enable or disable BIOS support for security device The optional settings are Disabled Enabled ACPI Settings Press Enter to make settings for the following sub item ACPI Settings ACPI Sleep State Use this item to select the highest ACPI sleep stat
26. tput Use this function to enable or disable MEBx Debug Message Output function Un Configure ME Use this function to enable or disable Un Configure ME without password function Amt Wait Timer Use this item to set time to wait before sending ASF_GET BOOT OPTIONS Disable ME Use this item to set ME to soft Temporary Disabled function ASF Use this item to enable or disable Alert Specification Format Active Remote Assistance Process Use this item to enable or disable Trigger CIRA boot function USB Configure Use this item to enable or disable USB configure function PET Progress Use this item to enable or disable PET events progress to receive PET event or not WatchDog Use this item to enable or disable WatchDog Timer When set as Enabled the following sub items shall appear OS Timer Use this item to set OS watch dog timer BIOS Timer Use this item to set BIOS watch dog timer Super I O Configuration Press Enter to make settings for the following sub items Super IO Confiquration gt Serial Port 1 Configuration Press Enter to make settings for the following items Serial Port Use this item to enable or disable serial port COM Change Settings Use this item to select an optimal setting for super IO device Transmission Mode Select The optional settings are RS422 RS232 RS485 Mode Speed Select The optional settings RS232 RS422 RS485 250kbps RS232 1Mbps RS422 RS485 10Mbps
Download Pdf Manuals
Related Search