AutoSat Light DIGITAL
Contents
1. check the consignment for completeness The following items are contained in the shipment AutoSat Light Digital Control unit box External unit and satellite aerial dish or flat aerial 6 way connecting cable for power supply and receiver 0 4 m length 12 way connector housing Washers M6 A2 srews M6 x 12 Sprengringe M6 A2 Self tapping screws 3 9x20 Cable gland feed through for the roof digital receiver optional User manual Guarantee card 1 1 Important Note Before installation and start up of your AutoSat light please read this user manual carefully Always make sure even when your AutoSat light will be retracted by your starter key that the system has really retracted when starting your vehicle In case of interrupted supply voltage for instance the aerial can no longer be automatically retracted Very important The external unit must be mounted on the vehicle roof with the aerial retracted in a direction opposite to the driving direction as otherwise one cannot rule out that the aerial will be blown up by wind during high speed driving When transporting the vehicle on a train the aerial must be fixed in the retracted position by additional suitable means expander belts etc due to railway wagons being turned around when re coupling Do not clean your AutoSat light external unit with a steam cleaner The rubber seals used for sealing will be OK for rain and water spray but cannot survive a water jet w2. connector may be plugged in 6 1 3 Connection power supply Prior to connecting the control unit with the vehicle power supply check the supply connector again to avoid possible damage due to incorrect connections AUTOSAT LIGHT DIGITAL USER MANUAL PAGE 15 6 1 4 Connection receiver The provided 6 pole connector plug comes with a ready made 12V circular plug with a 2 3 mm diameter for all standard satellite receivers This connector is designed for receivers with 8 maximum power input of 20 watts If your satellite receiver has a different 12V connector plug you need to replace that plug The receiver is only supplied with 12V when the antenna is extended This prevents the receiver from consuming power when the antenna is retracted 6 1 5 Remote control connection If the AutoSat Light Digital is mounted in a hidden position an optional external remote control may be connected to the AutoSat Light Digital The cable connecting the remote control is 2 5 m long Extensions to 10 m are possible Plug the cable to the socket labelled Remote located on the underside of the AutoSat Light Digital Make sure the plug is engaged fully in its socket 6 1 6 Initial operation If all the steps described have been carried out the system can be commissioned If you are not yet familiar with the details of operation please read the Operating Instructions first 7 Fault elimination Fan preme Blink codes See Section 4 3 of these O
3. 6 Connection and commissioning 6 1 Mounting the AutoSat Light Digital To fix the AutoSat Light Digital or the receiver it is best to use double sided adhesive tape Scotch 3M or Tesa Power Strip If screws are used always make sure they do not make contact with the electronic circuit or cause any other damage 6 1 1 Satellite aerial connector The satellite aerial cable is terminated with an F Connector on delivery Check the connector for damage and good seating before mounting The centre conductor must not be bent If the aerial cable has been shortened or lengthened a new F Connector must be fitted Either a crimp or screw connector may be used In either case the cable must be prepared as shown in the following figure Warning Take care that no small wires of the outer screen touch the inner conductor when mounting the connector causing a short circuit The aerial cable from the external unit is screwed to the left F connection labelled in Warning Do not use any tools to screw up a screw type F Connector on the cable and to fix the connector at the F connection These connections should only be finger tight The right F connection labelled out is the connection to the receiver 6 1 2 Connection external motor unit Prior to plugging in the connector to the external motor unit check it again for correct seating of the contacts If all contacts are fully inserted and in the correct positions see page 21 the
4. EC type label e1 according to 034609 the EMC Directive 2005 83 EC for installation and operation in motor vehicles AUTOSAT LIGHT DIGITAL USER MANUAL PAGE 17 Page 18 USER MANUAL AUTOSAT LIGHT DIGITAL AUTOSAT LIGHT DIGITAL USER MANUAL PAGE 19 CRYSTOP ISPLAY Gesellschaft fur Anzeigesysteme mbH Durlacher Allee 47 76 131 Karlsruhe 0721 611071 E 0721 62 27 57 info crystop de www crystop de No warranty for information in this manual Subject to technical alteration 05 08 Page 20 USER MANUAL AUTOSAT LIGHT DIGITAL
5. CRYSTOP DISPLAY GMBH AUTQSAT Light hi DIGITAL Digital Control Unit Intelligent satellite Receiver System for Motor Homes and Caravans H User Manual AUS GB Index 1 A 4 1 1 2a aaa a 4 1 2 Safety considerations iiiiiiernereiiceeeini cicala 5 1 3 Important operating considerations rwrennnnnnnnnnnnnnnnnnnnnnnnnnnnnnna 5 1 4 Disposal considerations ii ni tinie dna nici aan aan 6 1 5 een 6 2 Figure Control Paine 7 2 1 Figure Digital Control BoX ara 7 3 Sequence of automatic satellite search rrrr iii 8 4 Operating INSTUCHONS 9 4 1 QUICK reference orina dad 9 4 2 Special functions iiiaae ae a eenaa ae esaea a aeneae peosaal iaie ias eneee kani 9 4 3 Error code table uuu iii 10 5 aaa iene han 11 5 1 Choice of 11 5 2 External indiana 11 5 3 Mounting the external unit aan 12 5 4 Cable connection to the AutoSat Light Digital 221222n22nnnnnnnnn nne 13 5 4 1 AutoSat Light Digital connectors illustration ccocnnnnnnonoconcnnncnonnnononnnnnnnos 13 5 4 2 Sketch of connector housing rear view ii 14 5 5 Power supply asili a 14 6 Connection and CO
6. MMISSIONING ccocccocccccconononcncncnnnnnnnnenonenonenonenonenonenonenenenenenenenenenens 15 6 1 Mounting the AutoSat Light Digital ccceceee cece eens eeeeeeee sees sees sees eeeeeeeeeeeeeeeeees 15 6 1 1 Satellite aerial COMME CON wa sec 15 6 1 2 Connection external motor unit lai iaia a 15 6 1 3 Connection power SUPPLY acacia aid 15 6 1 4 Connection receive oea a A A Ad ste 16 6 1 5 Remote control connection accio aia 16 6 1 6 Initial ONS real cir adore 16 7 Fault GUAT 16 8 ana 17 Page 2 USER MANUAL AUTOSAT LIGHT DIGITAL AutoSat Light DIGITAL Dear Customer congratulations that you have decided on a AutoSat light This User Manual should help you to utilise the functions of your new satellite system optimally We have kept the operational details as understandable as possible while keeping them short The functional range of your device will be expanded steadily with software updates That way there may be additional operational steps which are not explained in this user manual or the operation of functions already available may change For this reason you should visit the Crystop homepage www crystop de from time to time to download the current user manual We wish you much joy with your AutoSat Light satellite system Your Crystop Team AUTOSAT LIGHT DIGITAL USER MANUAL PAGE 3 1 Please read this first Before commencing the installation
7. core Kabel 3 core Kabel brown brown pink thin thick green yellow grey white black 5 5 Power supply Warning For 24 volt vehicle mains a 24 V to 12 V converter will be required Run the AutoSat Light Digital only on batteries or a stabilised and requlated battery charger or power pack supplying a continuous current of 5 Amps DC A 6 pole connector with a short cable is provided Connect the 3 wires red black blue to the vehicle power supply with suitable connectors The bipolar twin wire with attached circular plug is designed for the 12V supply of a satellite receiver Attention If the power supply cable is altered or a different cable is used make sure the polarity is correct If the polarity is wrong the AutoSat Light Digital will be damaged To keep cable losses to a minimum use a cable with a cross section of at least 4 mm for the voltage supply The AutoSat Light Digital should ideally be directly connected to the battery by a dedicated supply cable Ensure that no other users are connected to the same supply cable If others are connected the cable cross section must be adjusted to a suitable larger size Connect the 1 mm blue cable to terminal 15 ignition on or to D alternator This will ensure automatic retraction of the dish to the parking position when starting to drive Botha 12 V and 24 V signal may be connected applies ONLY to the D control cable Page 14 USER MANUAL AUTOSAT LIGHT DIGITAL
8. he AutoSat Light Digital on whilst pressing the Sel button so that the mirror is moved to the upright position Use the washers and retainer rings supplied for all four nuts This concludes work on the roof 5 4 Cable connection to the AutoSat Light Digital 5 4 1 AutoSat Light Digital connectors illustration Service Display Remote Control PC connectio Motor Drive Connector LED Satellite Aerial output Aerial input S D Receiver Power Connector found Lay cables from the external unit on the inside of the vehicle to the AutoSat Light Digital The cables should not rub on sharp edges and should not be laid close to sources of heat Prior to inserting contacts in the connector housing ensure that the contacts are in a faultless condition and are not bent In particular contact blades must not be excessively spaced Insert contacts in the connector housing according to the following sketch Individual cable cores are marked in colours and connector housing recesses are numbered to eliminate confusion Please work very carefully because once the contacts have been inserted they cannot be removed without damage Ensure that each contact is fully inserted so that the contact blade is engaged After all contacts have been inserted push the connector housing together in a vertical direction to the contacts AUTOSAT LIGHT DIGITAL USER MANUAL PAGE 13 5 4 2 Sketch of connector housing rear view 6
9. he motor overcurrent fuse has switched the motors off Remove the obstruction Overcurrent elevation Aerial mirror has collided with an obstacle during its lifting or lowering movement The motor overcurrent fuse has siwtched the motors off Remove the obstacle Azimuth standstill The rotational movement motor doesn t move any longer The movement of this motor has run into a timeout The motor may be blocked by an obstacle Elevation standstill The motor for the lifting or lowering movement doesn t move any longer The motor may be blocked by an obstacle parameters or order a current update 4 Check the Aerial cable to the external unit tight fit of the connectors break in the cable User abort A user has aborted the current process by pressing a button 10 No satellite found 1 Check that there is a free line of sight to the satellite Trees will block reception 2 Make sure that the required satellite can be received with your size aerial at your current location 3 The Satellite search parameters have changed Check with us whether there are new Tuner faults Tuner module registers faults Try to search again after switching off the control devices If the fault remains send in the control device for repairs Page 10 USER MANUAL AUTOSAT LIGHT DIGITAL 5 Mounting instructions Please read the mounting instructions before starting the installation 5 1 Choice of installation site Firstly chec
10. itable free space on your roof The direct vicinity of the site selected must be free from objects higher than 20 cm which might shadow the aerial When this installation site has been found once again make sure that the control unit is within a cable length of 4 m If not relocate the installation site or the control unit or extend the cable by an additional extension set obtainable from us Please do not extend the cables to the external unit without prior consultation with us Note Secure the external unit with mechanical fastening systems which preclude loosening or detachment of the unit For sandwich roofs not offering adequate facilities for fastening through screws and internal counter plates are recommended In case of doubt please consult the manufacturer of your vehicle 5 3 Mounting the external unit Please proceed in the following order Use Sikaflex 252 as an adhesive sealant 1 Position the external unit with the outgoing cable pointing towards the rear of the vehicle 2 Using the base plate of the external unit as a template drill 2 holes on diagonally opposite corners with a 2 4 mm drill 3 Fix the external unit with two 3 9 x 20 self tapping screws to the roof Tighten the screws lightly Please keep in mind that an aluminium roof coating is only thin and the screws may easily be over tightened Then drill the remaining holes 4 Raise the external unit and clean the underside and edges of the base p
11. ith a pressure of several bars The use of drive in wash stations is deprecated and is entirely at your own risk A condition for satellite reception is free sight to the satellite i e even trees cannot be penetrated by a satellite signal Page 4 USER MANUAL AUTOSAT LIGHT DIGITAL 1 2 Safety considerations For your protection read the safety considerations carefully before you start running your new equipment The manufacturer accepts no liability for damages arising from faulty handling and failure to comply with safety provisions If the equipment has been modified Crystop is no longer responsible for ensuring that the legal requirements i e equipment and product safety laws electromagnetic compatibility are complied with On resale of the modified equipment the person responsible for the modification becomes the manufacturer and is liable accordingly Furthermore the Crystop Guarantee becomes inapplicable which may lead to a loss of warranty rights WARNING In order to prevent damage to your vehicle roof your AutoSat2 should not be operated in high winds and gusts AutoSat light is designed solely for installation and operation in motor vehicles and caravans The D conductor should always be connected The screws of the external unit should be checked regularly for tightness 1 3 Important operating considerations Installation location Ventilation Like any electronic device the AutoSat light unit produces heat H
12. k the location where you would like to place the AutoSat Light Digital and the receiver When selecting the installation location for the AutoSat Light Digital please observe that the system is operated from the device itself Optionally a remote controller is available however it cannot be used to change satellite selection The receiver should be in the vicinity of the TV if possible and visible from your seat because the system is operated using an infrared remote controller If the receiver has an external infrared receiver it can also be built in and concealed Please keep the following in mind ensure sufficient ventilation for the receiver avoid additional sources of heat in the mounting location ensure that the cables from the roof to the control unit fit ensure that the cable from the control unit to the receiver fits and that the cable from the receiver to the TV set fits 5 2 External unit Offset aerial The AutoSat Light 65 cm mirror has a base of 30 x 30 cm and requires a maximum radius of 40 cm because the LNB for example in North Europe The space requirement in the stationary position is shown in the following sketch AutoSat light F AutoSat light S Drehbereich Drehbereich AUTOSAT LIGHT DIGITAL USER MANUAL PAGE 11 When choosing the mounting location keep in mind that the cables to the external unit are 6 m long and that the external unit must have sufficient free space to turn Now select a su
13. late and the corresponding roof area removing all dirt and fatty residues Fully coat the base plate with a 3 mm thin coating of Sikaflex 252 and position the external unit on the roof as envisaged 5 Before screwing in the screws please fill the holes with Sikaflex Make a sealing joint around edge of the base plate 6 Drill a hole through the roof for the three outgoing cables min 15 mm diameter 7 Wrap the cable contacts with adhesive tape to avoid damage Each of the 3 cables is already fitted with a grey plastic PG gland Unscrew the 3 narrow plastic nuts and pull them off the cables Carefully push the cables with the PG glands through the side into the cable bushing push the plastic nuts back onto the cables and screw the 3 PG glands into the holes of the cable bushing Now push the 3 cables through the roof clean the roof surface in this area and fix the cable bushing above the hole with Sikaflex 252 and three 3 9 x 25 self tapping screws Fix the cables to the roof We use a 20 x 20 mm cable duct here and stick it to the roof with Sikaflex 252 Finally tighten the sealing caps for the PG gland caps so that the cables cannot be pulled out any longer Page 12 USER MANUAL AUTOSAT LIGHT DIGITAL 8 The aerial dish can only be mounted after the system has been connected electrically to the power supply and is ready for operation since the aerial arm has to be raised from its parking position electrically For this purpose switch t
14. owever the heat produced is innocuous and is discharged effectively Do not place any objects on the device Maintain a space of 5 cm above the device to allow the heat produced in the device to discharge Do not place burning objects i e burning candles on the device The rubber feet of the device may cause a colour change in treated furniture surfaces If necessary place the device on an appropriate mat Supply voltage Operate the control unit with a voltage of 12 to 14 4 V DC only Never open the device If repair becomes necessary it should be carried out be trained personnel Moisture Protect the device from moisture drips and splashes and do not place objects containing liquids i e vases on it Heat Radiation Do not place the control unit near a heating element or in direct sun light AUTOSAT LIGHT DIGITAL USER MANUAL PAGE 5 In the following cases disconnect the device from the power supply and ask an expert for help gt the device was subjected to moisture i e liquid got inside gt on major malfunction gt on major external damage 1 4 Disposal considerations The packaging of your unit consists exclusively of reusable materials which should be recycled Make sure that empty batteries from the remote control unit are not disposed in the household rubbish but are returned for disposal as hazardous waste to a dealer 1 5 General considerations Always make sure even when your AutoSat light will be retrac
15. perating instructions No picture 1 Try other programs at the receiver although the 2 Maybe the wrong satellite was found push the SAT button aerial is ina 3 Check the connection to the TV set If the connection is by coax receiving cable check the TV settings channel If the connection is by orientation SCART cable the TV set must set to AV or channel 0 Wrong Satellite 1 Repeat the Satellite search found Press SAT gt SEARCH SATELLITE Bad picture 1 You are in the fringe zone of the satellite footprint quality 2 if 1 does not apply check the aerial cable to the receiver for tight fit of the connectors 4 LNB has been turned System shuts 1 Check the battery voltage down 2 Your vehicle was started immediately Inexplicable 1 Switch your AutoSat Light Digital off and then on again by briefly error condition unplugging the connection plug Page 16 USER MANUAL AUTOSAT LIGHT DIGITAL 8 Technical data Power supply Supply voltage max ratings Voltage on control line D Current Power input Search mode type Reception mode type Current limit motors LNB LOF Noise level low high band Single LNB Twin LNB LNB control Measurements AutoSat Light Digital Approval by the German Federal Motor Transport 10 15V DC 10 30V DC 1 5A 20W 0 01 A 0 03W approx 2 5 A 9 75 10 6 MHz 0 3 dB 0 4 dB 14 18 V max 400 MA 20x15x7cm WxHxD Authority KBA of the
16. ted by your starter key that the system has really retracted when starting your vehicle In case of interrupted supply voltage for instance the aerial can no longer be automatically retracted A condition for satellite reception is free sight to the satellite i e even trees cannot be penetrated by a satellite signal At the edges of the reception area signal quality may be improved by turning the LNB South western Europe i e Agadir Canaries turn LNB by approx 35 clockwise looking from LNB to mirror North eastern Europe i e Greece Western Russia turn LNB um approx 15 anti clockwise For Australia consult the LNBF POLARISATION Satellite Signal Location Map Page 6 USER MANUAL AUTOSAT LIGHT DIGITAL 2 Figure Control Panel On Off Power Select Next light satellite satellite 2 1 Figure Digital Control Box AUTOSAT LIGHT DIGITAL USER MANUAL PAGE 7 3 Sequence of automatic satellite search The AutoSat Light Digital satellite system is turned on with the On Off button After turn on the satellite to be searched for will be shown in the display by one of the red light emitting diodes factory setting ASTRA1 or the last received You now still have some 5 seconds to change this setting using the Sel button To confirm press the Sat button If no button is pressed satellite search commences LED next to the On Off button goes out Once a satellite has been found by the s
17. the On Off button on the control unit or on the I On Off button optional remote control unit After switching on O the system automatically starts to search for the satellite which was set previously Retract antenna Ifthe AutoSat Light Digital is switched off LED Switch off off the On Off button is pressed again to On Off button retract the antenna after the AutoSat Light Digital is switched on If the AutoSat Light Digital O is already on LED on the On Off button needs to be pressed only once Change satellite If the currently found satellite is not the one you require then a search for the next satellite is Sat Sat button initiated by pressing the Sat button Satellite selection Press the Sel button to set a new satellite for the following search To confirm press the Sat Sel Sel button button 4 2 Special functions If the Sel button is kept pressed during the process of switching on the system drives to an upright position for mirror and LNB assembly AUTOSAT LIGHT DIGITAL USER MANUAL PAGE 9 4 3 Error code table In case of fault the operating display shows an error code next to the On Off button The number of blinks defines the following blink code Blink code Meaning rectification The vehicle was started The aerial moves to parking position Overcurrent azimuth Aerial mirror has collided with an obstacle in rotational direction T
18. ystem fine positioning is carried out Following this LED next to the On Off button lights up again the aerial signal is switched through to the receiver If the receiver is set to a program of the requested satellite the program will now be visible on the TV set Should this not be the case there is a possibility that the AutoSat Light Digital has found a different satellite By pressing the Sat button the search may be continued If no button is pressed within 120 seconds the AutoSat Light Digital is deactivated and must be switched on again However if the satellite system had found the correct satellites and you press the Sat key anyway it is possible that the satellite required is not found any more If the required programme cannot be seen switch the programming locations further on the receiver and check the reception for other TV channels After switching off the satellite receiver the LED next to the On Off button or on the optional remote control starts to blink as a reminder that the antenna is still extended To retract the antenna you must activate the AutoSat Light Digital by pressing the On Off button once and then press it again to retract the antenna On reaching the parking position the AutoSat Light Digital switches itself off completely Page 8 USER MANUAL AUTOSAT LIGHT DIGITAL 4 Operating instructions 4 1 Quick reference Switch on The satellite system is switched on with
Download Pdf Manuals
Related Search