Home

Manual

1. The Ethernet ports will auto sense for Full or Half duplex operation Duplex Operation Verifying After all Ethernet connections are made check the LED s corresponding to the ports that each of the devices are connected to Ensure that for each port that is in use the LED is on or blinking If a port LED is off go back and check for connectivity problems between that port and the network device connected to that particular port In addition the color of the LED should indicate the speed for which your device is connected at see prior section on LEDs Connection SECTION 6 SB CONFIGURATION PORT These managed switches have a USB port for device configuration Use a standard USB cable with a mini USB plug on one end and an A type USB plug on the other end The A type plug goes into a standard USB port ona computer The mini USB plug goes into the USB port on the switch Configuration Ports Refer to the software user manual for how to interface with the switch using the USB port TURCK 3000 Campus Drive Minneapolis MN 55441 Application Support 1 800 544 7769 Fax 763 553 0708 www turck com 5 SECTION 7 ECHNICAL SPECIFICATIONS Technical Here are the technical specifications for the Managed Switches covered by this manual Specs Copper RJ45 Ports 10 100BaseT or 10 100 1000BaseT Shielded RJ45 All standard IEEE 802 3 IEEE 802 3 802 3u 802 3x 802 3z 802 1p and more Yes allows you to use straight
2. Industr A IP20 Industrial Ethernet se Managed Switch MANUAL blisked 11 21 2019 minutemenn INDUSTRIAL ETHERNET MANAGED SWITCH USER MANUAL Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Section 6 General Information LED Indicators Installation Power Wiring Ethernet and Serial Port Wiring USB Configuration Port Technical Specifications Applicable standards and certifications hu cL us 3 Standard European Locations Directives TURCK 3000 Campus Drive Minneapolis MN 55441 Application Support 1 800 544 7769 Fax 763 553 0708 www turck com SECTION 1 ENERAL INFORMATION This manual will help you install and maintain the Managed Switches Installation of these managed switches will enable the user to wire redundant connections between nodes manage the network by monitoring gathering network data allow for browser or telnet configuration increase network performance and more Overview Unlike an Ethernet hub that broadcasts all messages out all ports the Managed Switches will intelligently route Ethernet messages only out the appropriate port Most importantly unlike a regular Ethernet switch very resilient networks can be implemented because the Managed Switch has the intelligence to detect and allow for ring Ethernet topologies In other words implementing this switch will optimize the network for optimal bandwidth conditions reduce the num
3. or cross wired cables 10 100BaseT ports Protocols supported Ethernet compliancy Auto crossover Auto sensing operation Full and half duplex 10BaseT and 100BaseT Yes on the TD and RD pair Automatic 1500 VRMS 1 minute es Auto negotiating Auto polarity Flow control Ethernet isolation lt Plug and play Cable requirements Twisted pair Cat 5 or better shielded recommended Max cable distance 100 meters General Specifications Ethernet switch type Managed with 8 Ethernet ports and USB configuration port Latency for 10 Mbps ports 16 us frame time typical Varies on load and settings Latency for 100 Mbps ports 5 us frame time typical Full or half duplex operation Configurable Input power typical all ports active at 100 Mbps 4 3 W 8 port 10 W maximum Extended protection 1 5 000 watts 10x for 10 uS or 250 volts 50x for 100 uS UL508 CSA C22 EN61010 1 EMI emissions C g FCC part 15 ICES 003 EN55022 EMC immunity IEC61326 1 IEEE C37 90 TURCK 3000 Campus Drive Minneapolis MN 55441 Application Support 1 800 544 7769 Fax 763 553 0708 www turck com
4. Power 1 and Power 2 have power applied to them It will be OFF if either input does not have power or the switch software is not running Power LED TURCK 3000 Campus Drive Minneapolis MN 55441 Application Support 1 800 544 7769 Fax 763 553 0708 www turck com 3 SECTION 3 NSTALLATION The Managed Switches can be mounted directly on a DIN rail Refer to the drawing below Note Make sure to allow enough room to route your Ethernet cables Recommended DIN rail mounting steps 1 Hook the top back of the DIN rail clip on the unit over the din rail 2 Push the bottom of the unit towards the DIN rail until it snaps into place JTD TURCK 3000 Campus Drive Minneapolis MN 55441 Application Support 1 800 544 7769 Fax 763 553 0708 www turck com SECTION 4 POWER WIRING These industrial Ethernet switches can be powered from the same DC source that is used to power your I O devices Voltage ranging from 10 to 30 VDC must be applied between the P1 plus terminal and the Minus terminal The chassis screw terminal should be tied to panel or chassis ground Overview Single DC Supply Dual DC Supplies Alarm Chassis Alarm Chassis Output cach Output GND pane Load panel Back of Switch DIN rail Single DC Power Redundant DC Power To r
5. ber of collisions and allow for redundant data path connections to reduce eliminate downtime Operation To further aid in network reliability and performance SNMP is available to extract and exchange network Statistical information Through the use of SNMP various groups of statistical information can be obtained such as TCP RMON IP and more to aid the user s job to extrapolate the health of the network The Managed Switches can support 10BaseT 10 Mbps and 100BaseT 100 Mbps on their M12 ports Each of these ports will independently auto sense the speed allowing you to interface to regular fast or gigabit Ethernet devices These general specifications apply to the Managed Switches Refer to Section 7 for complete technical Performance der 4 specifications Specifications Ethernet ports 8xRJ45 Ethernet Switch Type Managed with SNMP RSTP IGMP VLANs and much more Ethernet Protocols All standard IEEE 802 3 M12 Ports shielded 10 100 with auto negotiation auto crossover and auto polarity Standards The Managed Switches meet the following standards plus others and Safety Electrical safety UL 508 CSA C22 EN61010 1 IEC1010 EMC immunity IEC61326 1 IEEE C37 90 Install the Managed Switches in accordance with local and national electrical codes Lightning Danger Do not work on equipment during periods ofl ightning activity CER LISTED TURCK 3000 Campus Drive Minneapolis MN 55441 Applicatio
6. educe down time resulting from power loss these industrial Ethernet switches can optionally be powered redundantly with a second power supply as shown in the diagram The OK output that can be tied to a PLC input or other device to indicate when there is a power loss output is ON when both P1 and P2 are properly supplied with 10 30 VDC This output sources the same voltage applied to the switch power terminals SECTION 5 THERNET AND SERIAL PORT WIRING The Managed Switches provides connections to Ethernet devices on the factory floor managed devices and agents The other Ethernet ports are then connected to Ethernet devices such as PLCs Ethernet I O or industrial computers Electrical isolation is provided on the Ethernet ports for increased reliability Overview Use data quality not voice quality twisted pair cable rated category 5 or better with standard RJ45 connectors For best performance use shielded cable Straight through or crossover RJ45 cables can be used regardless of the device the switch is to be connected to as the Managed Switche is capable of auto crossover of MDI versus MDIX detection M12 Wiring Guidelines The RJ45 Ethernet port connector bodies on these products are metallic and are connected to the Chassis GND terminal Therefore shielded cables may be used to provide further protection To prevent ground loops the cable shield should be tied to the metal connector body at one end of the cable only
7. n Support 1 800 544 7769 Fax 763 553 0708 www turck com SECTION 2 ED INDICATORS The Managed Switches have communication LEDs for each port an OK output LED a status LED and dual power LEDs Refer to the sample pictures below for the location of these LEDs Overview Status LED Activity link and speed LEDs are integrated into the RJ45 ports Power LEDs Ok There are two Power LEDs on the Managed Switch Power 1 is used for primary power and Power2 is used for Power LEDs ie l i secondary power Both indicate if there is power applied to the respective terminal ACT LNK The two LEDs adjacent to each port indicates activity and link confirmation 10 100 LEDs ACT LNK LED This would indicate that there is not a proper Ethernet connection Link between the port and another Ethernet device Make sure the cable has been plugged securely into the ports at both ends On Solid This would indicate that there is a proper Ethernet connection Link between the port and another not flashing Ethernet device but no communications activity is detected This would indicate that there is a proper Ethernet connection Link between the port and another Ethernet device and that there is communications activity SPEED 10 100 LED Gren A 100 Mbps 100BaseT connection is detected Off A 10Mbps 10BaseT connection is detected OK Redundant This LED indicates the status of the power inputs The LED will be ON when both the

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents