DW37i - Kleenmaid
Contents
1. Check the indicator light and fill the tank completely If the tank is not empty after approximately 60 washings call a technician Arrange the items to restrict water retention as much as possible Leave the door ajar for a few minutes if possible Droplets on plastic items Tefal coatings etc These items have a low calori fic mass Arrange the items in the upper basket Poorer drying on rapid programmes On rapid programmes the drying temperature and drying period are reduced to cut down the duration of the cycle as much as possible Leave the door ajar for a few minutes Condensation on the wall of the inside door or the tub Condensation may form on the walls particularly after the appliance has cooled down sound insulation increases this occurance 29 15 INDICATIONS FOR THE TESTING LABORATORIES ENERGY EFFICIENCY TESTS ACCORDING TO AS NZS 2007 PROGRAMME Yo Normal Eco Washing capacity 13 standard place settings Arrangement of the items Figs A B C IEC load next page Loading as per the indications on next page without side shelves Setting for upper basket Low position Dosage of detergent 5 26 25 g of detergent Setting for rinsing product distributor 2 The water softene2. A short audible signal beep confirm the but ton s selection except for the On Off but ton 20 11 PROGRAMMING e Delaying the end of a programme Programme the finishing time in quarter of an hour stages by pressing the or buttons until you reach the desired time Confirm by pressing Start The screen counts down hour by hour until the programme starts End of the programme The light flashes 15 minutes before the end of the programme and then lights permanently once the programme has finished e Cancelling a programme Hold down the Start Cancel button for a few seconds the screen shows the pro gramme finishing time and two minutes later the current time You can reprogramme e Stopping the appliance When the programme has finished press the On Off button Q e Setting the audible signal The setting enables you to activate or de acti vate the beep at the end of the programme Access the setting by holding down the Set button until you hear a double signal long beep Keep on pressing Set successively until you have access to the parameter The setting is confirmed automatically after 10 seconds or by pressing Set switching to the next parameter Screen brightness Waiting for delayed start 130 Programme time remaining ic progress End of programme Beep activated POF Beep de activated 12 YOUR
3. Q The waste filter The large main filter The micro filter The filters are located in the centre of the tub and must be washed regularly to obtain opti mum washing results Actions Before removing the filters remove any waste on the large main filter with a sponge so that the waste does not block the sprinkler arms Rotate the spray arm as shown in the drawing Fig 14 Loosen the waste filter a quarter of a turn and then remove it Remove the main filter B O Remove the micro filter O Carefully clean filters Q B and C under running water Fig 15 Re installation Proceed in reverse order inserting filters C and and then Important Remember to lock the waste filter Q in place by pushing it in fully and turning it a quarter turn 23 13 CLEANING YOUR APPLIANCE e Periodically Every 3 or 4 months in order to remove any deposits run a special maintenance programme with out any items in the machine using a special dishwasher cleaning product Important Keep this product out of children s reach If not using your dishwasher for a prolonged period Clean your dishwasher completely and then unplug it from the electricity supply and close the water tap Protect your machine from potential frost Advice Do not use abrasive powders metal sponges and alcohol based or thinner based products Use a cloth or a sponge If you are moving house run a soaking pr
4. DISHWASHER S SAFETY SYSTEMS e SAFETY SYSTEMS e Door poorly closed If the door is poorly closed the confirmed programme is automatically cancelled after 3 minutes If you open the door during the cycle the programme light flashes e Programme access lock Throughout the period the programme is running or the full duration of the programme the programme selector and the buttons are automatically protected from any kind of manipula tion This unlocks automatically at the end of the programme or when the programme is can celled by holding down the Start button for 3 seconds e Advice on cleaning the filters Approximately every month your dishwasher advises you to proceed to service the F E filters see Section Cleaning the waste filters Fig 14 15 e Anti overflow system This system activates the drain pump automatically if the water in the tank reaches an abnormal level Anti leak protection system This system cuts off the water supply if a leak is detected under the appliance e Total safety This supply pipe is fitted with a device to cut off the water supply directly at the tap if there is a leak Alarm light For programme errors or incidents please refer to Section 14 If an operating abnormality occurs NB To unlock hold down the Start Cancel button for three seconds 22 13 CLEANING YOUR APPLIANCE e CLEANING THE WASTE FILTERS The filtration system consists of several elements
5. Washing at 55 65 C Rinse Rinse Rinse Hot rinse Hot rinse Hot rinse Fan assisted drying Natural drying Fan assisted drying 100 min 30 min 15 min 90 110 min 14 3 L 11L 4 5L 17 19 L 0 56 Kwh 0 8 Kwh 0 02 Kwh 1 3 1 5 Kwh 19 11 PROGRAMMING kleenmoid Advice Consult the Programmes table on the preceding pages to determine the programme you need for the type of items the quantity and the amount of food residue e Starting the appliance Press the On Off button Q to switch the machine on e Starting a programme immediately Select your programme by pressing one of the selection buttons The Auto programme canbe accessed by pressing the Auto button The X button scrolls the programmes to the left if the Power Jet programme is selec ted pressing this button causes the Prewash programme to be selected The button scrolls the programmes to the left if the Prewash programme is selec ted pressing this button causes the Power Jet programme to be selected When a programme is selected the relevant Finishing time 335e indicator light illuminates The screens shows l the envisaged time that the programme will end Programme time remaining L 2 Press Start the screen shows the progress remaining time for the programme Close the door the programme starts
6. and clean the filters and the drain Initiate a Soaking programme If the fault persists call a tech nician e POOR WASHING RESULTS Problem Possible causes What to do Food traces and deposits in the glasses Items poorly arranged mas ked by another larger item or situated underneath it items nested or jammed together Upper spray arm blocked by cutlery or a dish etc Filter poorly locked and lifting during washing Micro filter screen clogged One or more holes in the spray arm blocked Arrange the items properly Use the most appropriate areas and accessories for each type of item see instructions Check that the spray arm rotates freely Set the basket in the high position if necessary Check the filter s facing and that the filter is locked in place push it in fully turning it to the right Remove all the filters and clean them in warm water including the micro filter s screen once a month Remove the spray arm by turn ing the lever a quarter of a turn and clean it under the tap do not use any tool that could damage the holes Re install the spray arm Traces of grease Detergent dose too low ineffi cient detergent stale product Inappropriate programme temperature too low duration too short Increase the dose try another detergent Select a programme with a higher temperature 27 14 IF OPERATING A
7. be added After the tank has been filled with regenerat ing salt the indicator light may remain lit until the salt has dissolved sufficiently usually after one cycle or if the tank has not been filled completely for example when first put ting the machine into service using the sam ple This can be deactivated as indicated in the paragraph For multi purpose products set ting table Important If the salt overflows when filling the tank to avoid oxidization of the tub it is advisable to remove the salt crystals or to run a Prewash programme 12 7 LOADING OF RINSING PRODUCT Loading of rinsing product Fig 07 Important Only use a rinsing product designed for dishwashers The rinsing product ensures your items shine and are well dried Q When first putting the machine into service fill the tank until the level is flush with the top of the adjustment lever Pour in at least all the rinsing product provided The tank contains 120 ml approximately one glass The original setting is in the centre middle position reference mark 2 If you encounter marks or poor drying after a few cycles you can adjust the setting using the adjustment lever fig 07 Reference mark 3 will increase the setting Close the tank lightly g os 2 Rinsing liquid indicator light This illuminates when rinsing product is required It can be deactivated as shown in the para grap
8. one side and then the other Small leak around or under the appliance move the appliance to locate the leak Leak from the tap Leak from the appliance Cf table fault d07 Check that a seal is fitted and retighten the nut Close the water tap and call a technician Small leak at the door Appliance not stable or not level Door not centred on the tub Adjust the feet Re centre by adjusting the rear feet 25 14 IF OPERATING ABNORMALITIES OCCUR e THE INDICATOR LIGHTS Problem Possible causes What to do The salt light does not go out No salt or an insufficient quan tity of salt in the tank to trigger the float Refill the tank and wait for the cycle to end If you have soft water that requires no salt the light is constantly lit The lights all light up one after the other A light flashes and the pro gramme does not start Wrong programme Programme selector wrongly positioned between two not ches Cancel the current program ming by holding down the Start button for 3 seconds and then re programme Reposition the selector on a programme e RELATING TO PROGRAMMING DISPLAY Problem Possible causes What to do The cycle lasts too long The energy saving program mes last longer because the agitation and drying times are longer to compensate for the lower washing and drying tem perature
9. water Only use products specially designed for your dishwasher water softening salt deter gent and rinsing products As far as possible avoid opening the dish washer s door when it is operating and in par ticular during the heating phases because scalding steam may escape or you may be splashed with hot water The machine is fitted 1 FOR THE USER S ATTENTION with a safety system that immediately blocks the dishwasher s operation if the door is opened Never use chemical solvents in your appliance because these could cause an explosion Always close your appliance s door after loading or removing your items Do not lean or sit on your appliance s door when it is open You are strongly advised to disconnect the machine after use and turn off the water supply Unplug your machine before carrying out any technical work on it Avoid placing your machine immediately next to a cooking or heating appliance to prevent any risk of heat damage Do not place any items in your machine which are not certified as dishwasher safe If you have removed an item before the end of the washing programme it is important to rinse it carefully to remove any residual washing products If your appliance breaks down never attempt to repair it yourself Any repairs made by non qual ified personnel can cause significant damage or lack of control The machine complies with applicable safety regu
10. A normal amount of A normal amount of amount dried on dried on dried on adhering residue and greasy residue residue on baked on stains on everyday items grease residue everyday items from frying cooked Faster but cheese sauce etc consumes more energy PROGRAMMES g Power Jet g Universal dU Normal Yo Normal Ec PROGRAMME Hot pre wash Pre wash Pre wash SEQUENCE Washing at 70 C Washing at 65 C Washing at 55 C Rinse Rinse Rinse Hot rinse Hot rinse Hot rinse Fan assisted drying Fan assisted drying Fan assisted drying These values refer to normal conditions of use with separate products detergent salt rinsing product They may vary according to the load the temperature if you use combined washing products the water hardness and the supply voltage 18 10 WASHING PROGRAMMES Mixed Mixed Mixed Mixed Normally dirty Very short 30 Very short cycle Automatically Recommanded for minute wash with no detects the amount normally soiled specially designed detergent for of washing up and load for a small amount rinsing and the level of soiling less consuming in of daily items with a re dampening the Normal amount of energy limited amount of items while dried on residue on non greasy residue waiting for a wash everyday items not dried on expected Faster but in the following two consumes more days energy lt Normal YE normal Eco Quick is Prewash AUTO Pre wash Cold pre wash Pre wash Washing at 45 C Washing at 45 C
11. BNORMALITIES OCCUR e POOR WASHING RESULTS White marks Chalky film removable with Check that there is salt in the identify what type vinegar tank light unlit OK Check the water hardness at the tap and that the water sof tener is set correctly Adjust it to a higher level if necessary Water too hard for using a 4 in 1 detergent without the addition of salt Traces of salt items have al_ Check that the stopper on the salty taste salt container is closed correctly White marks Glass cloudy because water Check the water hardness at identify what type too soft cannot be removed the tap and that the water sof tener is set correctly Some detergents in pellet form are more aggressive to glasses and decorations change the product and use a protective product if necessary Coloured marks tea wine cof Items poorly arranged Turn the cavities in the items ____ towards the jets Detergent dose too low ineffi increase the dose try another cient detergent detergent Programme temperature tool Select amore suitable programme low with a higher temperature If you use a multifunction Use the 4 in 1 option product depending on the model Streaks or dried droplets on Lack or insufficient amount of Check the indicator light and rinsing product fill the tank completely Adjust the dispensing unit to a higher position if necessary Rinsing product out
12. DISHWASHER collection Vv Instructions for Use and Warranty Details Dishwasher DW37 Zkleenmoid The best you can own Zkleenmoid The best you can own 2 CONTENTS 1 FOR THE USER S ATTENTION e Safety instructions 4 e Environmental Protection 5 e Economical environmentally friendly washing 5 2 DESCRIPTION OF YOUR APPLIANCE e General presentation of the dishwasher 6 e Presentation of the control panel 7 3 INFORMATION 8 4 WHAT TO DO BEFORE FIRST USING THE MACHINE e Measure the water hardness and select the type of detergent __ 9 e Hardness table 9 5 DETERGENT PRODUCTS AND ADJUSTING THE WATER SOFTENER e For traditional products 10 e For multi purpose products 11 6 LOADING OF REGENERATING SALT 12 7 LOADING OF RINSING PRODUCT 13 8 YOUR DISHWASHER S EQUIPMENT The lower basket 14 e The upper basket 15 e The cutlery basket 16 9 SETTING THE PARAMETERS 17 10 WASHING PROGRAMMES TABLE 18 11 PROGRAMMING 20 12 YOUR DISHWASHER S SAFETY SYSTEMS 22 13 CLEANING YOUR APPLIANCE e Cleaning the waste filters 23 14 IF OPERATING ABNORMALITIES OCCUR 25 15 INDICATIONS FOR THE TESTING LABORATORIES 30 16 WARRANTY AND SERVICE 1 FOR THE USER S ATTENTION Important Keep this user s manual with your appliance If the appliance is sold or trans ferred to someone else ensure that the man ual is with it Please take note of th
13. Set A long press Access to the Settings menus Set the current time Set the water softener Activate or deactivate use of regenerating salt rinsing product or Washing product depending on the water softener setting see next page Beep at end of programme Set screen brightness e The screen shows you the current time the finishing time the remaining time for the programme and the parameter settings Delaying the end of a programme Press one of the buttons or the other to select the time for the programme to end Advice The indicator lights S Salt When lit it indicates lack of regenerating salt Sie 2 Rinsing liquid When lit it indicates lack of rinsing product Washing product Indicates that your dishwasher is set for using 2 3 or 4 in 1 tablets End lit indicates that your programme has finished Start Cancel Briefly press this button to start your programme If you make an error to cancel a selection or cancel a programme while it is running hold down this button for 3 seconds A short audible signal beep confirms the button s selection except for the On Off button 3 INFORMATION Important To obtain impeccable washing and drying results from your dishwasher without any marks you must set it carefully using the water softening system which utilises rege nerating salt As rainwater infiltrates into
14. ce is not intended for use by young children or infirm persons unless they have been adequately supervised by a respon sible person to ensure that they can use the appliance safely This appliance must only be used by adults Ensure that children do not touch it and do not use it as a toy Ensure that they do not operate the appliance s controls Keep young children away from the appli ance when it is operating Detergents contain irritant and abrasive sub stances These products can have caustic effects on the eyes the mouth or the throat They can be extremely dangerous if ingested Avoid any contact with the skin and the eyes Ensure that the appliance s detergent contain er is empty at the end of the washing cycle Place detergents out of children s reach and do not put any detergent in the machine until just before you start the washing programme The water in your dishwasher is not drinking water this is why children must not go near the appliance when its door is open Do not let your children play or sit on the door when it is open Once you have unpacked your appliance place the packaging out of children s reach Keep all the packaging materials e g plastic bags polystyrene etc out of children s reach because they can be dangerous for children ie risk of suffocation e Use When machine is running do not open door This may provoke steam leakage or splattering of
15. e first five years of ownership as the original purchaser of this Kleenmaid appliance we guarantee that any fault caused by faulty material or workmanship beco ming apparent will be rectified free of charge for parts and labour provided that all service is per formed during normal working hours by Kleenmaid or their designated Agents Where the appliance is installed outside the normal servicing area of the above the Purchaser must pay for the cost of transporting the appliance to and from the Agent or the Agent s travelling cost to and from the Purchaser s home COMMERCIAL WARRANTY ONE YEAR WARRANTY When this appliance is installed in a commercial application you the Consumer have under the relevant laws in respect of this appliance during your first one year of ownership as the original purchaser of the Kleenmaid appliance we guarantee that any fault caused by faulty material or workmanship becoming apparent will be rectified free of charge for parts and labour provided that all service is performed during normal working hours by Kleenmaid or their designated Agents Where the appliance is installed outside the normal servicing area of the above the Purchaser must pay for the cost of transporting the appliance to and from the Agent or the Agent s travelling cost to and from the Purchaser s home WHAT THESE WARRANTIES DO NOT COVER We are not responsible for any damage or malfunction unless caused by a defect in material or workman
16. ese instructions before installing and using your appliance They have been drawn up for your own and other people s safety e SAFETY INSTRUCTIONS e Installation When you receive your appliance unpack it or have it unpacked immediately Check that it has not suffered any damage during transport Express any reservations in writing on the delivery note of which you keep a copy Never connect up a damaged machine If your appli ance is damaged please contact your dealer Before proceeding to connect up your machine please refer to the instructions in your Installation Guide Your dishwasher must be kept disconnected from the mains supply throughout the whole of the installation process The electrical connection details on your appliance s description plate must comply with those for the mains supply The socket must still be accessible once your appliance has been installed Do not alter or attempt to alter the appli ance s characteristics This could put you at risk If your installation has to be altered only entrust the electrical and plumbing work to a qualified electrician or plumber respectively Your appliance is designed for normal domestic use Do not use it for industrial or commercial purposes or for any other pur pose than that for which it has been designed The dishwasher s walls must not be pierced under any circumstances e Children s safety This applian
17. f in any doubt please contact the detergent s manufacturer if the items are very wet at the end of the programme or if chalky deposits appear 4 WHAT TO DO BEFORE FIRST USING THE MACHINE e MEASURE THE WATER HARDNESS AND SELECT THE TYPE OF DETER GENT TRADITIONAL OR MULTI PURPOSE In one simple action you can test the your water s lime content using the testing strip supplied with your dishwasher Alternatively contact your local water utility to ascertain your water s hardness Let the water run from the tap for a few moments Fill a glass with water Take the test strip from its holder and immerse it for 3 seconds Wait 1 minute shake it and look at the colours to ascertain your water s hardness e HARDNESS TABLE 0 10 F 10 25 F 25 40 F 40 55 F 55 70 F Water Sort Sightiy hard Sighty hard Very hard F Essential if using Essential if using Fe Optional traditional traditional Mandatory Mandatory Mandatory products products or Multi purpose Traditional products P Powder detergent or L Liquid detergent S Regenerating Salt R Rinsing product Multi purpose products Multi purpose tablets 9 5 DETERGENT PRODUCTS AND ADJUSTING THE WATER SOFTENER e FOR TRADITIONAL PRODUCTS Your machine must be specially adjusted to use traditional products e Proceed as follow
18. h For multi purpose products setting table Important If any of the product overflows during filling sponge up the excess to avoid pro Fig 07 Adjustment lever ducing foam 13 8 YOUR DISHWASHER S EQUIPMENT Very important Items not suitable for washing in a dishwasher Wooden cutting boards Stainless steel utensils or plastic utensils that are not heat resistant Copper or pewter items Glued crockery and cutlery Cutlery with wooden horn or mother of pearl handles Antique or hand painted porcelain When purchasing crockery glasses or cutlery ensure that it is dishwasher safe THE LOWER BASKET Arrange your items so that the water can cir culate freely and spray over all the utensils Place large diameter dishes and pans at the sides Do not intersperse jam together or superim pose flat plates and concave dishes Fig 08 A The flexible racking spikes makes it easier to ANA iy dishes Fig 09 i AN arrange your large dishes Fig 09 AD Advice INAN When you re insert the lower basket ty ensure that nothing catches on the oversize plate barrier to avoid blocking the rotating spray arm mae ma Y UAP TH Unloading your items Empty the lower basket first to avoid drips from the upper basket falling onto the lower basket 14 8 YOUR DISHWASHER S EQUIPMENT THE UPPER BASKET This basket is particularly designed to take glasses cups ramekins small
19. ing light lit On Rinsing light lit multi purpose light flashing NB You can deactivate the Salt and Rinsing lights when using multi purpose products this is done using the salt button page 17 e Loading the multi purpose tablet dispenser To assist in loading the detergent the distributor is situated on the front of the upper basket It is compatible with all the products recommended for dishwashers e Place the tablet in the external compartment Fig 04 on previous page or for optimum results pull out the distributor s drawer and lay the tablet inside Fig 05 on previous page Close the dispenser 11 6 LOADING OF REGENERATING SALT e Loading of regenerating salt Fig 06 Filling with salt is essential for providing a good wash without marks It regenerates the resins that soften the water by removing its lime content unless the mains water supply is soft enough Refer to Setting the water sof tener Important Only use special dishwasher regener ating salt Do not use table salt or any type of cooking salt this could damage your appli ance s water softener Q Unscrew and remove the stopper on the salt tank B Fill the tank with regenerating salt special ly designed for dishwashers O Use the funnel supplied with your dish washer The first time top up with water up to the rim of the tank e Regenerating salt indicator S This illuminates when salt must
20. kery bones pips etc Do not pre wash your items by hand useless waste of water Utilise your dishwasher s capabilities to the full for an economical environmentally friendly wash Always select a washing programme suitable for the crockery type and how dirty they are Avoid overdosing with detergent regenerating salt and rinsing liquid Follow the recommenda tions in this guide pages 9 13 and the instructions on the product packs Ensure that the water softener is correctly set see pages 10 11 2 DESCRIPTION OF YOUR APPLIANCE e GENERAL PRESENTATION OF THE DISHWASHER W Lg Za Ss Q Control panel Regenerating salt tank Q Upper basket waste filter C Washing products dispenser Main filter D Anti blocking gauge wire Q Rinsing product dispenser Lower sprinkler arm J Description plate After Sales Ref Advice This user s guide is applicable to several models There may be some slight differences in the details and the equipment between your appliance and the descriptions provided here 2 DESCRIPTION OF YOUR APPLIANCE e PRESENTATION OF THE CONTROL PANEL Zkleenmoid Q on off Press this button to start your dishwasher AUTO press this button to select the Automatic programme Choosing a programme briefly press one button or the other in succession to select your programme
21. l compartment Fig 04 or for optimum performance pull out the dispenser drawer and lay the tablet inside Fig 05 e Powders or liquids Fig 03 Fill at least up to the minimum mark for slightly dirty crockery and to the maximum mark for dirty crockery If the crockery is very dirty and for programmes with a pre wash we recommend that you add 5g of detergent a dessert spoonful into your dishwasher s tub in accordance with the pro grammes table Important Keep these products out of children s reach and away from dampness Only use products specially designed for dishwashers 5 DETERGENT PRODUCTS AND ADJUSTING THE WATER SOFTENER e FOR MULTI PURPOSE PRODUCTS e Your appliance can be specially set to use multi purpose if the water hardness is lt 25 F Advice To provide better coverage of the wide range of multi purpose products available your dishwasher s option has two possible settings accessible via the Set button Extra Dry improves the drying results in the event of reduced performance from the 2 in 1 3 in 1 or 4 in 1 types of multi purpose product Sparkling Clean enables you to prioritise the sparkle of your crockery whatever the type of multi purpose product used e Proceed to set water softener Access setting mode by holding down the Set button until you hear a double audible signal long beep The water softener setting is displayed on the scree
22. lations Any repairs should be carried out by qualified technicians Repairs or changes that do not conform may be dangerous for the users In case of replacement only use original parts If the machine malfunctions due to other causes than those mentioned in this booklet disconnect the machine remove the plug or break the circuit concerned and contact Kleenmaid s after sales service ENVIRONMENTAL PROTECTION This appliance s packaging material is recyclable Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose Broken machines should be taken to the closest recycling centre Destroy the door closing system so it no longer works children may close themselves in whilst playing and suffocate Cut the elec tric cable after having removed the plug from the socket Your appliance also contains a great amount of recyclable material It is marked with this label to indicate the used appliances that should not be mixed with other waste This way the appliance recycling organised by your manufacturer will be done under the best possi ble conditions in compliance with European Directive 2002 96 EC on Waste Electrical and Electronic Equipment Contact your council for the used appliance collection points closest to your home We thank you doing your part to protect the environment e ECONOMICAL ENVIRONMENTALLY FRIENDLY WASHING Remove any food residue from your croc
23. n for example C3 To use multi purpose tablets you must select setting CO or ci depending on the water hardness To do this keep on briefly pressing one or other of the lt gt keys until you reach the desired setting e Proceed to select the Multi purpose option and set it OFF deactivates the J option Qn corresponds to activation of the option with the Sparkling Clean setting This enables you to prioritise a brilliant finish for your crockery Qn corresponds to activation of the J option with the Extra Dry setting Extra dry enhances the drying results if performance is reduced The light then illuminates permanently if this option has been selected The setting is validated automatically after 10 seconds if the Set button is not pressed again Pressing Set enables you to validate the setting and move on to the next parameter 5 7 m Testing strip T s Hardness 0 10 F 10 25 F Pea thy 0 Multi purpose e Zk ua B c products Function Deactivated cg gt OFF ci OFF DIE a Multi purpose 2 lt products Sparkling Clean c On a gt In Multi purpose e e products Extra Dry cdl On ci aee On Oa Dry
24. of date or _ Use a recent product a good inefficient product dilutes easily and foams in cold water If you use a multifunction Use the 4 in 1 option with a product setting prioritizing drying parametering from the menu depending on the model Dried on marks on glasses dull If you use a multifunction Use the 4 in 1 option with a product setting prioritizing brilliance parametering from the menu depending on the model 14 IF OPERATING ABNORMALITIES OCCUR e POOR OPERATION Problem Possible causes What to do Constant filling A lot of waste on the large filter at the end of the cycle Drain hole situated too low for the appliance Cf table fault d012 The filters and drain outlets are blocked with too much residue Drain wand has fallen on the floor Remove and clean the filters and the bottom of the drain outlets Remove large residue from the plates before putting them in the machine Traces of rust on stainless steel Quality of the stainless steel not dishwasher safe knives in particular Use special dishwasher safe cutlery Check that the lid on the salt con tainer is closed correctly e POOR DRYING RESULTS Problem Possible causes What to do A lot of droplets on the glasses Lack or insufficient amount of rinsing product The dose has not been distrib uted Positioning of the items
25. ogramme first of all in order to avoid any water escaping 24 14 IF OPERATING ABNORMALITIES OCCUR e SUMMARY OF THE FAULTS d01 water supply fault tap d02 draining fault d03 heating fault d04 temperature fault d05 fault motor under load d07 overflow anti leak fault d08 sprinkling distribution fault d11 pressure sensor fault d12 filling fault water inlet detection system d13 overheating fault d06 fault motor overload d14 pump filling fault e BEFORE CALLING FOR SERVICE Problem Possible causes What to do The door falls heavily when opened integratable model Door springs not tensioned enough to compensate for the weight of the panel Tighten the two tensioning screws accessible in the bot tom section above the front feet The door does not stay horizontal when open or returns too quickly integratable model Door springs tensioned too much No wooden panel Loosen the two tensioning screws accessible in the bot tom section above the front feet Fit a temporary wooden panel on the appliance and adjust the springs The door catches when closing Appliance not stable Door not centred on the tub Adjust the feet Re centre by adjusting the rear feet The upper basket does not stay in the high position Poor manipulation the basket is being pulled upwards too quickly Act more progressively see instructions
26. r must be set to 0 10 F instructions in the paragraph on Adjusting the water softener Door ajar 100 mm upon completion of dry test For more information on the comparison tests in accordance with AS NZS 2007 please contact the manufacturer of the machine before commencing testing NB When conducting tests using a multi function tablet Check that the water softener is correctly set for the water hardness Chapter 5 DETERGENT PRODUCTS AND ADJUSTING THE WATER SOFTENER e FOR MULTI FUNCTION PRODUCTS Pull out the detergent distribution drawer and place the tablet in the interior compartment e Measuring the noise level in accordance with Standard EN60704 2 3 Align the plinth on the housing unit with the door panel 30 15 INDICATIONS FOR THE TESTING LABORATORIES IEC LOAD A ME aee il eC Sas w or 3 G Lor VOD EPS 000 222 pane 224 FY mH 15 INDICATIONS FOR THE TESTING LABORATORIES AS NZS LOAD Lor Lor AA J K Lo S NOTES 33 NOTES 34 16 WARRANTY AND SERVICE DOMESTIC WARRANTY FULL FIVE YEAR WARRANTY In addition to all statutory rights which you the Consumer have under the relevant laws in res pect of this appliance during th
27. s Use these programmes prefe rably at night when it is not so important how long the pro gramme lasts or when it ends The appliance trips the circuit breaker Insufficient amperage to sup ply all the appliances being operated simultaneously Internal fault in the appliance Check the socket s amperage 10A minimum and the meter s capacity Call a technician The appliance does not start No mains power to the socket Tap closed Cf table fault d01 Water supply hose kinked Selection error or programme blocked Start button pressed too long greater than 2 secs Appliance in Safety mode anti leak Cf table fault d07 Check the socket and the fuse Check the tap is open Check the hose line is OK Cancel by holding down Start for 3 secs and re programme Just press Start briefly to start the programme Call a technician 26 14 IF OPERATING ABNORMALITIES OCCUR Problem The appliance will not restart The appliance does not drain Cf table fault d02 Possible causes Door opened during a washing cycle The cover has not been remo ved from the sink s U bend Drain hose kinked Filters totally blocked Pump blocked What to do Wait for the time delay to end controlled internally by the appliance Remove the cover Check the drain hose line behind the machine is OK Remove
28. s to adjust the water softe ner on the control panel Access setting mode by holding down the Set button until L I ouik B J you hear a double audible signal long beep Then press a twice briefly to access the water softener setting The water softener setting is displayed on the screen for example C3 To adjust and alter the setting to suit the water hardness keep on briefly pressing one of the E keys or the other The screen shows you the setting CQ Ci Ce etc The setting is validated automatically after 10 seconds if the Set button is not pressed again Pressing Set enables you to validate the setting and move on to the next parameter S O Tes sa ele S68 See ee 2222F Hardness 0 10 F 10 25 F 25 40 F 40 55 F 55 70 F gt 70 F Softener Traditional gt setting products cu Ci Cc cs c4 c5 Nb Factory setting C Important It is very important to set the water softener correctly If the setting is too low there is the risk of chalky marks appearing if the setting is too high there is the risk of causing clouding of the glasses If you relocate adjust the water softener setting as required e Traditional tablets Non multipurpose tablets should be placed in the externa
29. salad bowls bowls and saucers Arrange your items methodically to save on space arranging glasses cups or bowls together You can also arrange cups ladles etc on the folding cup racks Fig 10 Advice Position the cavities of glasses cups or bowls facing downwards e Adjusting the height of the upper basket For large dishes to be loaded in the lower basket the upper basket must be set to the high position This can be done with the bas ket fully loaded Fig 11 Setting in HIGH POSITION Gently raise your basket on each side until it engages Setting in LOW POSITION Raise your basket completely on both sides to unlock it and then lower it to the low position Important Check that the two slides are set to the same height and the basket is horizontal 15 Cutlery basket 8 YOUR DISHWASHER S EQUIPMENT e THE CUTLERY BASKET The cutlery basket slides to allow flexible loading It can be placed anywhere in the lower basket You can therefore make a variety of loads depending on the items Fig 12 If your cutlery items or your dishes are too Wey large alter the height setting for the upper Se NY XA basket ADN Y VS SS y Movable grills are available if you wish to load your cutlery in an orderly manner Fig 13 Optimum washing and drying use these sep aration grills partially or totally Point the handles on the cutlery downwards Importan
30. ship This includes but is not limited to abuse misuse improper installation and trans portation damage We are not responsible for any consequential damages from any malfunction The Consumer must make the appliance available for servicing and shall bear any costs incurred for any de installation and or re installation required to make the appliance available for servicing Kleenmaid are not liable for any consequential damage incurred during de installation or re instal lation WARRANTY DOES NOT COVER REPLACEMENT OF LIGHT GLOBES OR GLASS BREAKAGE DUE TO IMPACT In case of fractured glass do not use your appliance WARRANTY REGISTRATION Please complete warranty details below and retain together with your proof of purchase docu ment These documents will need to be viewed by our Service Representative should you request in warranty service SERVICE ASSISTANCE To assist you when phoning our After Sales Service number to arrange a service call please com plete the following details and have them ready when you call Model Number Date of purchase Kleenmaid Store purchased from Date of installation KLEENMAID CUSTOMER SERVICE CONTACT NUMBER 1300 652 100 Kleenmaid Head Office PO Box 5560 MAROOCHYDORE BC QLD 4558 For your nearest store call 131308 or visit www kleenmaid com B3097C 01 07 Z Kleenmoid The best you can own
31. t For safety reasons we recommend that you place knives with pointed ends with the point facing downwards in the cutlery basket to avoid the risk of an accident Long bladed knives and other sharp kitchen utensils must be placed flat in the upper bas ket Avoid washing cutlery with horn handles in your dishwasher Separate silverware from other metals using the separation grill 16 9 SETTING THE PARAMETERS e SETTINGS POSSIBLE USING THE SET AND SELECTION BUTTONS 1 long press on the Set button and then a short press enables you to move on to the following parameters Set the parameters by pressing one of the programme selection buttons or the other Move on to the next parameter by pressing Set 1 long press Briefly press the Set button once and then press one or other of the selection buttons Advice gt Setting the clock hour To do this hold down the Set button When the time starts to flash press one of the selection but tons or the other until you reach the desired time Press SeT to move on to the next parameter gt Setting the clock minutes Proceed in the same way as above press one of the selection buttons or the other to set the minutes gt Setting the water softener Set to the level corresponding to the hardness of your water CU to cS gt Product use You can cancel display of the relevant indicators depending on the prod
32. the ground it picks up mineral salts some minerals are found in solid form and are commonly called lime This reduces the detergent s washing perfor mance and leaves white marks on the crockery The more lime there is in the water the harder the water is Use the most suitable washing products for the hardness of your town s water supply There are several types of products Important Never use normal washing up liquid For ease of use and in certain water hardness conditions only lt 35 F multi purpose_ products can make the use of regenerating salt and rinsing liquid unnecessary e Two in one tablets contain deter gents and rinsing liquid or an agent serving the function of the salt e Three in one tablets contain detergents and rinsing liquid as well as an agent serving the function of the salt e Four in one tablets also contain additives that prevent wear on poor quality glasses or the risk of stainless items corro ding For an impeccable clean opt for using traditional products together Washing product for a perfect clean standard powder liquid or tablets Regenerating salt for your dishwa sher s water softener to work correctly Rinsing liquid to assist drying and eli minate drip marks Important Follow the instructions in the user s manual and the recommendations on the multi purpose detergent s pack NB I
33. ucts used Salt gt Set to OFF if you do not use salt or if you are using multi purpose tablets Rinsing product Set to OFF if you do not use a rinsing product or if you are using multi purpose tablets gt Multi purpose tablets only for CO or Ci activate the option For optimum product performance depending on the water softener setting table on page 11 set OFF To deactivate the option n to select 3 with Extra Dry Dn to select with Sparkling Clean gt Beep at the end of the programme ON to activate the function OFF if you do not wish to hear the beep at the end of the program gt Screen brightness Set the screen brightness to suit yourself from Lul minimum to LUS maximum Display J IbP OF Lu e Lu 3 The setting is confirmed automatically when you move on to the next parameter or if the Set button is not pressed again within the next 10 seconds 17 10 WASHING PROGRAMMES e PROGRAMMES TABLE As an indication only Duration in min 130 min 90 min 130 min Water L 17 L 17 L 15L Energy Kwh 1 7 Kwh 1 5 Kwh 1 3 Kwh ITEM TYPE porcelain pans cut Resistant Mixed Mixed lery glasses FOOD RESIDUE Very dirty Normally dirty Normally dirty Quantity typeand A large amount of
Download Pdf Manuals
Related Search