Home

ComPar KIT 1 & 2 DMX LED light set with power outputs User manual

image

Contents

1. ComPar KIT 1 amp 2 DMX LED light set with power outputs n _ EOMrAP HIT 1 COMPAR HiT E User manual Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV Introduction Thank you for purchasing the Ayra ComPar Kit You have either purchased the ComPar Kit 1 or ComPar Kit 2 This user manual is suitable for both products as the products are almost identical The main difference is the used LED light source Read this user manual before you set up the system to become familiar with the product and its accessories Also check the box contents for possible damage or missing parts lf you encounter any problems during use contact your local dealer for more information and help The Ayra ComPar Kit is a versatile lighting system used for entertainment purposes It is an ideal system for mobile DJ s solo entertainers and bands who wish to add colourful changing lights to their performance This will enhance the mood of your audience The ComPar Kit consists of a bar with four projectors mounted each projector can be individually adjusted and aimed It is possible to cross beams or make a fan shape of all projectors The options are nearly limitless Each ComPar Kit projector uses a RGB colour mix system This gives every user the possibility to choose betw
2. Plug in the power supply to a matching power outlet Power switch is not in the ON position Turn on the device by switching the ON OFF switch to the ON position if available The fixture does not respond to DMX signals Wrong DMX address Set the DMX address to the right value DMX controller blackout function activated Deactivate the blackout function of your DMX controller Faulty positioning of the DMX polarity switch on the controller flip the polarity switch on your DMX controller No response or DMX activity signal LEDs active Check your DMX cables for possible connection breaks and replace them if necessary The fixture does not respond to sound Wrong working mode selected Check if the sound activated mode of the fixture is activated Microphone sensitivity level is set too low Increase the microphone sensitivity of the built in microphone Speaker placed too far away or lack of bass Place your lighting effect closer to your speakers or vice versa and or increase low frequency volumes The microphone will not be triggered with high pitched sounds The beam output is very low Dirty dusty optics Clean the lens and or other optics with a dry or damp cloth Dimmer is not set to full output Set all dimmer levels to 100 on your DMX console Sometimes the DMX signal is lost and or some fixtures are flickering behaving odd sometimes Faul
3. 145x 10mm LED 49R 48G 48B for each projector 50 000h estimated lifespan ComPar KIT 2 7x 9W Tri Color RGB LED modules for each projector 50 000h estimated lifespan Projector features Four separate projectors on each system equipped with ventilation slots for optimal cooling and long lifespan wide angle manual pan and tilt for each projector individually for optimal beam adjustment solid cable from every projector to the main bar Connectors DMX 3p XLR male and female Power IEC power connector Foot controller 5p XLR Included accessories 1x lighting stand max height 2 8m 1x foot controller with connection cable 1x padded case for ComPar Kit 1 or 2 1x lighting stand case 1x power cable IEC Schuko 1x signal cable for foot controller 5P XLR 5P XLR Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV
4. the supervision of an adult This device is not suitable for children Every person involved with the installation operation and maintenance of this device has to Be qualified Follow the instructions of this manual Make sure there is no damage caused by transport If the device seems damaged from the outside do not use it and contact your dealer for more information and consultation To make sure the device maintains in perfect condition and for safe operation it is necessary for the user to follow the instructions and warning notes of this user manual Damage caused by improper use or modifications to the device are not covered by warranty This device does not have any user serviceable parts inside Servicing of this device needs to be done by qualified technicians Important notes regarding safety and health Never let the power cord come in contact with other cables Handle the power cord and all connectors with the mains with caution Never remove any warning or informative labels from the unit The ground contact always needs to be connected Do not cover or remove the ground contact Never leave cables lying around Do not open the device and do not modify any hard or software of this unit Do not insert this object into air vents Do not connect this device to a dimmerpack Do not switch the system on and off frequently as this will reduce the lifespan of the device Do not drive the inputs of th
5. 10 158 172 Color chase 11 173 187 Color chase 12 188 202 Color chase 13 203 217 Color chase 14 218 232 Color chase 15 233 247 Color chase 16 248 255 Stand alone CH7 Speed 000 007 Hold p 008 255 Speed slow to fast 12Channel Mode Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV 16 Channel Mode CH14 000 007 No function Strobe 008 247 Strobe slow to fast 248 255 Sound strobe CH15 000 007 Manual 008 022 Color chase 1 023 037 Color chase 2 038 052 Color chase 3 053 067 Color chase 4 068 082 Color chase 5 083 097 Color chase 6 098 112 Color chase 7 Colore 113 127 Color chase 8 128 142 Color chase 9 143 157 Golor chase 10 158 172 Color chase 11 173 187 Color chase 12 188 202 Color chase 13 203 217 Color chase 14 218 232 Color chase 15 233 247 Color chase 16 248 255 Stand alone CH16 Sneed 000 007 Hold p 008 255 Speed slow to fast Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV Installation and maintenance Installing the system in a standing position right side up The ComPar KIT 1 and 2 are equipped with a 35 mm stand adapter which makes it possible to position th
6. ComPar Kit 1 and 2 This means that it is theoretically possible to connect a total of 20 ComPar Kit fixtures in a single line without power problems As the maximum power capacity of the power outputs combined is 1610W Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV Setting up the unit The ComPar KIT series comes with a practical lighting tripod stand Extract the feet of the stands until they are fully extended Pull the distance tube out until you reach a proper install height and tighten the knob Use the included safety pin to ensure that the stand will not be able to slide down Place the ComPar KIT bar on the stand To activate the unit connect the included power supply to the unit and a suitable 230V 50 Hz power outlet The unit will activate directly after it is plugged in to a wall outlet or other power source The status of the fixture is shown on the display Certain values determine the current status and will change when you push buttons on the control panel The buttons each have their own function for easy navigation in the control panel Display codes Description display Mode sid Function Description _ _ ADDR DMX address setting A001 A512 Set the DMX start address by choosing a value between 1 and 512 CHND Channel mode 1 channe
7. controller Connect the foot controller to the first fixture with the 5P connector then feed the signal through from fixture to fixture with the DMX in and outputs DMX mode The most extended working mode as this function gives you the ability to control the system with a standard DMX 512 controller using the 3p DMX in and outputs Select one of the several channel modes and set the right starting address After this you have full control over the system with your DMX controller This unit has the following DMX channels and DMX values 1 Channel Mode 000 007 Blackout 008 037 Show 01 038 067 Show 02 068 097 Show 03 098 127 Show 04 128 157 Show 05 Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV 158 187 Show 06 188 217 Show 07 218 247 Show 08 248 255 Random Show 01 08 3 Channel Mode CH1 Red 000 255 Dimmer 0 100 000 255 Dimmer 0 100 000 255 Dimmer 0 100 7 Channel Mode CH1 Red 000 255 Dimmer 0 100 _ _ CH5 000 007 No function Strobe 008 247 Strobe slow to fast 248 255 Sound strobe CH6 000 007 Manual 008 022 Color chase 1 023 037 Color chase 2 038 052 Color chase 3 053 067 Color chase 4 068 082 Color chase 5 083 097 Color chase 6 098 112 Color chase 7 ou 113 127 Color chase 8 128 142 Color chase 9 143 157 Color chase
8. d Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV Fuses The main fuse of this device is to be found on the rear of the device In most cases directly next to the power inlet Only replace a fuse for a new one with the same type and rating Do not use a fuse with a higher or lower rating Do not bridge the fuse with electrical wires aluminum foil as the fuse is used for protection against electrical shocks and short circuit Always mount the fuse cover back to the fuse compartment Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV Light effect guidelines WARNING This lighting device is capable of suddenly producing concentrated light beams which might cause disorientation when looking directly into the optical systems on short distance Do not look directly into the optical lens from short distance WARNING This lighting device has a built in strobe mode which creates pulsating bright beams Do not use this function continuously in a dark environment as this might cause disorientation Any information and illustrations shown in this user manual are subject to change wi
9. d not be present If any visual or mechanical damage is detected contact your local dealer or a specialized technician Do not use a damaged or failing fixture Connectors and wiring schematics DMX connections Electrical wiring DMX output DMX input ALR mounting socket XLR mounting plug 1 Ground 2 Signal 3 Signal 1 Ground 2 Signal i 3 Signal Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV DMX lighting troubleshooting If you have any problems with DMX lighting consult this troubleshooting section to solve any difficulties with your product If this troubleshooting section does not solve your problem contact your dealer for more information and help This troubleshooting section contains the most frequent problems and is not a complete collection of possible faults defects and solutions The troubleshooting section applies for DMX controllers DMX cabling and DMX lighting fixtures It is possible that not all described problems causes and solutions apply to your situation as product details may vary from product to product Problem Possible Cause Solution The fixture does not activate itself Blown fuse Check the fuse compartiment for blown fuses and replace it if necessary No power cable plugged in
10. e fixture frequently with a damp cloth to remove dust and or dirt WARNING Always disconnect the fixture from your wall outlet or other power supply and let the fixture dry before reconnecting it This prevents possible electrical shocks Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV The lenses can be cleaned with a non aggressive glass cleaning solution but is not recommended Ayra recommends to clean the mirror and lens with a fine brush while removing dust and or dirt with a vacuum cleaner Avoid touching the lenses with your bare fingers to prevent fingerprints on the optics Checkup To prevent dangerous situations make sure your fixture is in optimal condition before using it Check your fixture frequently by using the following checklist All screws must be mounted tightly Check all screws and metal parts for corrosion No visible corrosion may be present The exterior of your fixture must be in optimal condition Check your fixture for dents cracks or missing parts Your installation spot must be in optimal condition Check your installation spot for corrosion cracks dents and strength Electrical components connectors and cables must be in optimal condition Any form of damage cuts exposed wire cores or any other visual deformities shoul
11. e fixture with a signal larger than required to work at full performance Only use this device indoor avoid contact with water moist or other liquids Do not place items filled with liquids on top of the unit Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV Avoid nearby flames or heat sources do not place this device near flammable liquids gas or flammable items Always disconnect the device when it is not in use for a longer period or time when servicing is needed or when the device needs cleaning Only handle the power cord by its connectors Never pull the cable to remove a connector from its socket as this could lead to damage and electrical shocks Always operate this device with a stable AC current Always operate this device with the AC ground wire connected to the electrical system s ground Never use other types of cables than specified in the manual do not use defective or bad functioning cables Contact your dealer when the included or required cables do not work properly with this device When the device has been exposed to large temperature differences for example transport from outdoor to indoor do not connect the device immediately Do not activate the unit until it has reached room temperature as moist might build up inside the uni
12. e system on a standard loudspeaker or lighting stand A screw knob is attached to the adapter used to tighten the system so it is unable to turn around This also prevents unwanted rattle noise caused by speaker vibrations and possible instability as tube diameters of stands may always vary slightly Installing the fixture in a standing position inverted It is possible to use the LED projectors as a floor spot system for example when you want to use them for uplighting purposes For this feature use the screw knobs at the top of the system and mount a floor stand on each side floor stand not included Invert the display status by using the menu option for easy reading of values After this flip the system and position the bar as you wish NOTE You may need to replace the screw knobs for standard bolts as the height of floor stands may vary Installing the fixture in a hanging position When installing the system in a hanging position for example on a truss construction detach the screw knobs and install proper G clamps or half couplers not included NOTE When installing the system in a hanging position the following list of safety precautions must be met Use at least two hanging points clamps for optimal stability and safety Use at least one recommended amount 2 safety cable s capable of holding 3x the weight of the system Safety cables must be installed in such a way that it is impossible for the system
13. een thousands of colour tones for each projector Make use of the built in features of the system for example the sound activated mode or the built in colour presets It is also possible to link multiple fixtures in a master slave mode For advanced control use the DMX mode to control the complete bar or every single projector with a DMX controller The all new ComPar Kit series have built in power outlets to pass wall outlet power through to other lighting effects Combined with the ability to mount other third party projectors directly onto the system you are able to create a unique light setup for almost every venue Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV Safety instructions A WARNING A Always keep this device away from moisture and rain Hazardous electrical shocks may occur A WARNING A Only connect this device to a matching power outlet This device is intended to work on a specified AC currency Connecting this device to power outlets with other voltages may result in permanent damage and possible hazardous situations such as fire or electrical shocks A WARNING A Be careful with every operation of this device Touching live wires inside and outside the unit may cause hazardous electrical shocks This unit must be operated by or under
14. l mode Select the DMX channel 3 channel mode mode which will determine 7 channel mode how many channels the unit 12 channel mode will fill on your DMX 16 channel mode controller More channels more specific functionalit SLND Slave mode Slave 1 Slave 2 NOTE Only possible by connecting two ComPar KIT units with each other by 3p XLR cable Set the unit to Slave 1 sync or Slave 2 mirrored mode Show mode Show 1 Show 8 Select any internal automatic show for stand alone applications Sound mode Sound on off Activate or deactivate the music controlled mode Sound sense Sound sense 0 100 Select the sensitivity of the sound active mode BLND Black out mode LED mode YES NO Activates or deactivates the beam output for the LED projectors Display inversion Display Inversion dsp dspl Inverts the display when the unit is used upside down as large floorspot with floor stands This makes it easier to read certain display statuses TEST Test mode Self test Self test program projects all colours separately This makes it possible to check if there are defect LED modules Using time of light Fixture hours 0 9999 Displays the run time of the fixture Used by rental companies to determine Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV service
15. maintenance intervals version Software version Ver XXX Firmware software version not upgradeable by users Foot controller features Blackout Blackout the unit Strobe Select color Select Show 1 Synchronous strobe in white Red 1 8 2 Sound strobe in white Green 3 Sound strobe in color Blue Red Green Red Blue Function Green Blue Red Green Blue Color change by sound Sound LED OFF Manual Color LED ON Show LED slow blinking Working modes Stand alone automatic Select one of the internal programs which will activate and run in a continuous loop Music controlled mode sound active Activate the internal microphone by using the display and set the right sensitivity for optimal music controlled shows Select one of the predefined shows The show will change step by step when sound is detected Master slave mode sync mode Connect two or multiple ComPar KIT systems with a standard 3p male to 3p female XLR cable The first system will act as a master fixture the second system will mimic the actions of the first system thus creating synchronized effects To ensure that this function works properly use the DMX OUT connector of the first system and the DMX IN connector of the second system Set the second system to Slave 1 or Slave 2 mode synchronized or mirrored mode Connecting more than 1 slave is possible with a maximum of 16 units The Master slave mode also works when using the included foot
16. njury caused by improper use Storage and transport This device is intended for mobile use When transported use the original packaging of the product ora fitting flightcase preferably filled with foam This device is not intended for permanent use Operation breaks will ensure that the lifespan of the device remains unchanged If the device is not used for a longer period of time disconnect it from its power source and store it in its original packaging or in a fitting flightcase Store the device indoor dry and do not expose the device to extreme temperature differences Housing Inspect the housing of the device frequently Severe dents cracks and missing screws should be avoided at all costs Do not use the device when the housing is not in optimal condition Contact your dealer or a skilled technician when in doubt about the state of the device Check the fixture and screws for corrosion Corrosion should not be present on the fixture Contact your dealer or a skilled technician when corrosion is found on the fixture Every power or signal chassis connector should be mounted tightly Do not use the device when connectors are loose Do not use the power cord when the cores are visible Contact your dealer for a replacement if needed Avoid the buildup of dust and dirt Clean the exterior of the fixture every month with a dry or damp cloth When using the device intensively the cleaning frequency needs to be increase
17. nputs amp outputs The ComPar Kit fixtures have independent fuses for the bar itself and the power outputs They are directly connected to the AC power input which they share The internal wiring of the fixture is built to withstand a load of 16A max total The ComPar Kit fixture electronics are equipped with a F3A 20mm fuse The Power outputs are equipped with a F7A 20mm main fuse which bears the total load for the power outputs Every power output is capable of being loaded with 7A max but the combined load for both output can not exceed 7A Doing so will result in blowing the internal fuse Even though the bar may withstand a larger load the 7A fuse is chosen for safety reasons No problems will occur when connecting one two or several LED lighting fixtures Connecting fixtures with a high power consumption such as fog machines is not recommended by Ayra Any load greater than 16A total on the power outputs will also cause the 7A fuse to blow But in addition to that chances are high that the circuit breaker of your power circuit may also cut the power causing other fixtures connected to the circuit to deactivate due to the loss of power The fuses inside the ComPar Kit act independent of each other Therefore any power issues with connected lighting fixtures that cause the output fuse to blow will not result in problems for the bar itself so it will keep running and prevent total blackout Fuses and ratings are identical for the
18. ode of the fixture If the wrong value is set change the channel mode to a different setting and try again Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV Technical specifications Compact lighting system Equipped with four projectors Projectors individually adjustable Colourful light effects thanks to RGB LED light source Automatic sound active master slave and DMX working modes Two selectable Slave modes Microphone sensitivity digitally adjustable for sound active mode Several DMX channel modes 1 3 7 12 or 16 channels LED display with menu buttons Display invert IEC power inlet Screw knobs at the top Integrated stand adapter with screw knob Included foot control for easy light show control by musicians and DJ s Included lighting stand for easy plug and play setups Included transport bag for the system lighting stand for optimal safety and convenience during transport and storage Power requirements 110 230V AC 50 60 Hz Power consumption 80W Two power outputs suitable for powering other ComPar kits ComPar fixtures or LED lighting fixtures ComPar Kit fuse F3A 20 mm glass Power outputs fuse F7A 20 mm glass Total weight 10 5 kg LED Light source ComPar KIT 1
19. t which may cause shortcuts and or electrical shocks Guidelines and types of use This device is intended to be used by professionals on stage in theaters clubs and other equal venues This device is not suitable for children and always needs to be operated by an adult Only use the device when the environment is suitable and will not cause any damage Do not use the product in moist or dusty environments or where long term damage may occur such as indoor swimming pools where chlorine is used Beaches where sand and salt are present Outdoor without roof protection Indoor areas where intense heat sources are present or where the temperature exceeds levels which are comfortable for humans Only use the included power adapter and only connect the device to a suitable power outlet with the correct output voltage Connecting the device to a power outlet with the wrong type of voltage or using the product with a wrong type of power supply may cause permanent damage to the device Avoid shocks and collision during use and transport Do not transport the device while in use Avoid brute force during the installation and operation of this device Familiarize yourself with the functions of the device before use Do not allow operation of the device by unskilled or unqualified people Use of the device in other ways than described in this user manual may cause damage and injury Ayra does not take responsibility for any damage or i
20. thout further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV Box contents Box contents 1x Ayra ComPar Kit 1 or 2 1x lighting stand 1x foot controller with connection cable 1x padded case for ComPar Kit 1 or 2 1x lighting stand bag 1x power cable IEC Schuko 1x signal cable for foot controller 5P XLR 5P XLR Unit and accessory inspection Always use the supplied power cable to connect the unit to a power supply If the cable appears broken or has visible damage do not use it If the unit is not going to be used for a longer period of time disconnect it from the power supply and store it in a dust free environment Always check the unit for possible damage before use If you suspect that something is wrong with the unit do not connect it to a power source When you suspect that your unit is broken or damaged contact your local dealer or a certified technician to inspect the unit Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV Device overview COMPAR HIT amp FOOT CONTROLLER Beam output Tightening knob for hooks light effect mounting etc Stand mounting adapter with tightening knobs for placement on the included standard oO N 4 Do
21. to fall down when one of the two mounting points breaks It is prohibited to install the system by using only safety cables or chains Warranty is void when any of the above safety precautions are not met Ayra can not be held responsible if any damage or injury occurs due to improper use of the system Transport When using this fixture in mobile setups provide sufficient protection during transport Always use the provided transport bags to protect the system and included lighting stand Replacing the internal fuses First check whether a failing power supply may be the cause of malfunction When you suspect that one of the internal fuses is broken the fuse can be replaced by removing the fuse cover located on the rear of the fixture near the power inputs outputs and control menu WARNING Before checking the fuse always disconnect the fixture from your wall outlet or any other power supply to prevent electric shocks Always replace a broken fuse with a fuse that has the same type and rating After the fuse has been replaced always close the fuse cover Reconnect the fixture to your power supply and check whether the problem is solved When this does not solve your problem contact your local dealer for help Spare parts This unit has no user serviceable parts inside When any damage to internal components occurs contact your local dealer or a specialized technician in order to repair the fixture Cleaning Clean the housing of th
22. ty oroken DMX cables Check your DMX cables for possible connection breaks and replace them if necessary Power cable interference on your Avoid installing the DMX and Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV DMX signal high power cables parallel to each other No DMX terminator Apply a DMX terminator at the end of your DMxX chain Signal loss or distortion in DMX values Apply a DMX booster in your DMX chain after 32 fixtures or less After a maximum of 32 fixtures the DMX signal needs to be refreshed Moving parts are not functioning well values do not match and or rattling sounds are noticed Faulty stepping motor positioning Possible value loss of stepping motors Activate the reset function or unplug the power supply and plug it back in to activate the reset program This will reset all values to the original O point The fixture does not respond fast enough to the set speed on my DMX controller Moving parts can not keep up with the set speed Decrease the chase speed of your DMX controller as the stepping motors of your fixture need some time to move from one point to another The fixture does not respond to all DMxX channels Wrong DMX channel mode Check the DMX channel m
23. uble braced lighting stand with extension tube safety pin and tightening knobs O1 Storage and transport bag for ComPar Kit fixture foot controller and cables Foot controller Suspend button blackout Menu button select working mode Up button select colour or show 0 Full button Full output white blinder fade function N Od Any information and illustrations shown in this user manual are subject to change without further notice User manual version 2 0 Creation date author initials 30 07 2013 RV Revision date author initials 11 02 2014 RV a rs ON Tuy OMX SLAVE N maerens esouno es COMPAR KIT Agaur OOOO KIT FUSE 100 240 V 50 60Hz O is IS 1s 1 O y f f f O o oe y PN NN Ary nN PA AC IN POWER Me m l DMX IN DMX OUT FOOT CONTROLLER PaE pl 100 240V 50 60Hz 100 240V 50 60Hz 11 AC power output 110 230V AC 50 60 Hz to power other lighting fixtures during use on a stand or in a truss construction 12 LED display with menu buttons 13 ComPar Kit fuse fuse for the ComPar Kit itself 14 AC power input 110 230V AC 50 60 Hz to power the fixture and if connected other lighting fixtures 15 Power output fuse fuse for the ComPar Kit power outputs 16 DMX input with 3P XLR 17 DMX output with 3P XLR 18 Foot connector connector 5P XLR 19 Built in microphone for sound activated mode Important notice Power i

Download Pdf Manuals

image

Related Search

Related Contents

ProLite E2003WSV-1  Dicam Data Logging Capabilities  95101 MODE D'EMPLOI - FR USER GUIDE  Samsung GH68-11254A Bluetooth Headset User Manual  Samsung CRT Television User's Manual  高画質・高品位のEIZOクオリティを 継承する、新世代15型LCD  Einhell BT-SS 405 E  

Copyright © All rights reserved.
Failed to retrieve file