Network Settings
Contents
1. 38 Audio Video Codec Parameters Audio Parameters Mute Check the option will make the Network Camera reboot to force all the connection using HTTP mode to view the video therefore no audio can be heard at any client side Improve audio quality in low bandwidth environment Check the option will make the Network Camera reboot to make communication of audio channel more efficient Audio Source The selection can be Internal microphone or External microphone When External microphone is selected the red light of the Network Camera will blink once a second Video Parameters Text on video The text will be displayed in the black bar above the video window with a timestamp The timestamp is captured from the date and time of the Network Camera that is maintained by a built in real time clock Color Select either for color or monochrome video display Size There are five options for three video sizes Half is the quarter size of Normal Half x 2 has the same video size as Normal but of a lesser quality while consuming less network bandwidth Normal x 2 will do digital zoom with factor of 200 for both width and height of the video and Double will have the Network Camera sending 704x480 NTSC 704x576 PAL size video to every connections with the maximum frame rate of 10 Maximum frame rate This limits the maximal refresh frame rate which can be combined with the Video quality control to o2. Troubleshooting chapter of the Appendix Add Password to Prevent Unauthorized Access The default Administrator s password is blank and the Network Camera initially will not ask for any password The Administrator should immediately implement a new password as a matter of prudent security practice Once the Administrator s password is saved the Network Camera will ask for the user s name and password before each access The Administrator can set up a maximum of twenty 20 user accounts Each user can access the Network Camera except to perform system configuration Some critical functions are exclusive for the Administrator such as system configuration user administration and software upgrades The user name for the Administrator is permanently assigned as root Once the password is changed the browser will display an authentication window to ask for the new password Once the password is set there is no provision to recover the Administrator s password The only option ts to restore to the original factory default settings How to Use Authentication After opening the Web browser and typing in the URL of the Network Camera a dialogue window pops up to request a username and password Upon successful authentication the following figure is displayed The foreground is the login window and the background shows the message if authentication fails The user may check the option box to save the password for future conve
3. IPaddress Network Camera s IP address 56 keep the original way O h WLAN infrastructure mode WLAN Ad Hoc mode channel in USA channel in Canada channel in Europe channel in Spain channel in France channel in Japan all 1 Mbps transmission rate 2 Mbps transmission rate 5 Mbps transmission rate 11 Mbps transmission rate Mbps transmission rate Mbps transmission rate 12 Mbps transmission rate 18 Mbps transmission rate 24 Mbps transmission rate 36 Mbps transmission rate 48 Mbps transmission rate 54 Mbps transmission rate n C Un gt CU Q 5 10 13 X 73 A CU L O 91 e s c O D e D m Ly CU D 3 gt lt i O UI O gt iO OV z z ect D UD WQ Y Q E ct UO CU ect D Q ect TR CU UD 3 UD Uu O CU ect D N I UJ ong preamble short preamble enable data encryption disable data encryption auto authentication most strict shared key authentication open key authentication 64 bits key length 128 bits key length hexadecimal format of key ASCII format of key one of four keys exadecimal string 00 FF network key 1 D C I3 J N HB Uu D x W e e e e NI U1 BR U0 N Re e e Re Re A2 O 2 ect n S n e II v m A D EE XE 9X es JA WJ Re HR Q y Q g T _ 0 D V Q Uu 2 O 73 ct D 73 ct gt CU 2 CJ CJ O auto open key D 5
4. Factory default Version 0100d amp Done url http Network Camera gt setup config html Network Camera is the domain name or original IP address of the Network Camera Host name e WCS 2010 P T IP Camera LevelOne wCS 2010 P T IP Camera C Turn aff the LED indicator 9 Keep current date and time Sync with computer time PC date C2 Manual Date Time Automatic MTP server Time zone Update interval 2004 07 13 Dry mm dd PC time 7 2 5 hh mm ss 2004 07 13 yyyy mm dd 17 08 12 hh mm ss skip to invoke default server GMT vil One month 31 System Parameters Host name The text displays the title at the top of the main page Turn off the LED indicator Check this option to shut off the LED beside the lens It can prevent the camera s operation being noticed Keep current date and time Click on this to reserve the current date and time of the Network Camera An internal real time clock maintains the date and time even when the power of the system is turned off Sync with computer time Synchronizes the date and time of the Network Camera with the local computer The read only date and time of the PC is displayed as updated Manual Adjust the date and time according to what is entered by the Administrator Notice the format in the related fields while doing the entry Automatic Synchronize with the NTP server over the Intern
5. Right Up Down and Home functions The Home button centers the camera Go to Once the Administrator has determined the preset positions the User can aim the camera using this control Pan speed This button sets the moving range of the Left and Right commands Tilt speed This button sets the moving range of the Up and Down commands Auto pan This button commands the camera to pan from the current position to the left most and then to the right most position After panning the camera returns to the original position Auto patrol This button commands the camera to patrol between the preset positions on the Patrol List which can be modified on the Camera control page After one patrol cycle the camera returns to the original position Stop This stops the Auto Pan command or Auto Patrol command 11 Client Settings At the initial access to the Connection type page in Windows the web browser will ask for a new plug in installation the plug in being the Network Camera This plug in has been registered for certification and can be used to change the parameters at the client s site The user may click on to install the plug in If the web browser does not allow the user to complete the installation check the Internet security to lower the security level or contact your IT or networking supervisor Client settings Microsoft Internet Ex
6. Select one Signing 2001 CA Pan speed In iml Caution DOCA Co Ltd asserts that this content iz sale You should anl install vssve thes content i vau trust COCA Go Ltd to make that agsertion Tibsueed fo Pan Stop Patrol Always bust content from DOCA Co Ltd Digital Output Jo More Into ON OFF Snapshot l Client Settings Configuration Zocm E I RS RERM Primary User s Capabilities Main Screen with Camera View The main page layout has three parts Configuration functions The camera can be configured using these user interfaces Camera View What the camera sees Pan Tilt control buttons These buttons provide a command interface to control the aim of the camera Click on the configuration link to the left of the image window to enter the configuration page E LevelOne WCS 2010 F T IP Camera Microsoft Intemet Explorer ERO RAEO RRA RRB A IAT HAH E gt O44 Que Genet Que C zh 59 EX 3 FED http 192 168 0 133 CRE m LevelOne WCS 2010 P T IP Camera eet Tilt speed o zi E Digital Output eme The Configuration Digital Output Clicking on the On or Off button turns the digital output to either on or off status Snapshot The button provides users a fast way to capture a single image of the video from the Network Camera Client Settings Clicking on this button links
7. AN Never turn off the power during the upgrade firmware process verzon 1 1 DO NOT POWER OFF THE CAMERA WHEN UPGRADING 11 After successfully upgrading the finish dialog will show and ask you if you need to upgrade another machine Uperade Wizard X Update firmware O E Another i version 1 0 29 12 Launch the IE browser to connect to the Video Server After inputting the User Name and password the main page should display Click the Configuration linkage Z Levels BRE HE RAG EREA IAM HAU StH 9 QOD Que genet Que 65 50 43 SEQ http 192 168 0 133 ne WCS 2010 P T IP Camera Microsoft Internet Explorer LevelOne WCS 2010 P T IP Camera ulti A J a F Configuration By I eme 30 Definitions in Configuration Only the Administrator can access system configuration Each category in the left column will be explained in the following pages The bold texts are the specific phrases on the Option pages The Administrator may type the URL below the figure to directly enter the frame page of configuration If the Administrator also wants to set certain options through the URL read the reference appendix for details H MI MI m M mM M gt HOME System Security Network Mail amp FTP DONS amp UPnP Audio Video Camera control Motion detection Application View log file View parameters
8. Chinese The default software is English Please skip the steps if you don t need to upgrade multi language e Please follow up the steps as below if you have to upgrade your language manually WCS 2010 Network Camera Upgrade Software Procedure 1 Launch the Installer exe from your CDROM IF Installer Please restart your device and select one by clicking the serial number Current IP Address O0 02 D7 00 20 6D 192 168 0209 IP Installer Link to selected device Selected device Mone Enter the IP address you want to assign and click the Set IP Address buttan 0 0 0 Use this IP whenever system boot Check this option will skip installation procedure whenever the device starts up Set P Address 25 2 Select the Camera you want to setup and click Link to selected device button IF Installer X IP Installer Version 1 0 Please restart your device and select one by clicking the serial number 7 Senes Number C rent IP Address l 19P 168 0 209 Assigned OD 1 00 20 60 2 2 Link to selected device Selected device This server has already been assigned IP Search Enter the IP address you want to assign and click the Set IP Address button 152 168 0 209 Use this IP whenever system boot Check this option will skip installation procedure whenever the device starts up Set P Address 3 Please Enter root as username
9. DDNS amp UPnP Configuration URL Mail amp FTP Configuration URL Audio Video Configuration URL Camera Control URL Image Quality Configuration URL Application Configuration URL 42 42 43 44 46 47 47 48 48 49 52 52 52 52 52 53 54 54 54 55 56 56 58 58 59 61 61 62 Installation Hardware Installation Please verify that your product package contains all the accessories listed in the foregoing Package Contents Depending on the user s application an Ethernet cable may be needed The Ethernet cable Should meet the specs of UTP Category 5 and not em exceed 100 meters in length EXT VO ae amp Connect the power adapter jack to the Network Power cord socket Camera before plugging in to the power socket This will reduce the risk of accidental electric shock Upon powering up the device runs through a self test procedure and the front LEDs will blink between green and red a few times If self test passes the LEDs will shut off and the Network Camera will be on stand by and ready for software installation If self test fails the red LED will blink several times Refer to Appendix A for troubleshooting The LevelOne WCS 2010 Network Camera will first detect Ethernet If it does not connect to Ethernet the Network Camera will try WLAN During the searching and connecting process to the wireless access point or station the red LED of the Network Camera will flash every second Until the Network Camera connects to t
10. default Preset function Jersian 0100d area Selects J Select gt Remove DN On the Camera Control page there are two main function control areas Camera Control Area The pan and tilt functions can be controlled with these buttons The Left button aims the camera to the left the Right Up and Down buttons aim the camera accordingly The Home button aims the camera to the center Pan speed This controls the range of the horizontal movement of the camera The greater the value the greater angular movement when performing the Left or Right functions Tilt speed This controls the range of the vertical movement of the camera The greater the value the greater angular movement when performing the Up or Down functions would be Auto pan patrol speed This defines the speed of panning and patrol the greater the value the faster the speed 44 Preset Function Area Enable IR control Checking this box allows the Administrator to enable the IR controller to move the aim of the camera To allow controls only through URL commands or web pages leave this box unchecked Current position If the User wants to save the current view as a preset location enter a name for each of the current video view at current position and click on the Add button The camera allows for 20 preset locations Preset position This keeps a l
11. if the network is protected by a firewall and it only allows HTTP Port 80 to be opened In this mode audio will not be sent and only video is operational Ifno special need is required UDP protocol is recommended Generally speaking the client s choice will be in the order of UDP TCP HTTP After the Network Camera is connected successfully Protocol Option will indicate the selected protocol The selected protocol will be recorded in the user s PC and will be used for the next connection If the network environment is changed or the user wants to let the web browser to detect again manually select the UDP protocol save and return HOME to re connect HOME dedia Option Disable audio Pratacal Option The auto detecoon order of transmission protocol is UDP gt TCP 2 HTTP Please select ane protocol as the default protocol C UDP e TCP C HTTP Video only Save url http Network Camera gt protocol html Network Camera is the domain name or the original IP address of the Network Camera 13 Administrator s Capabilities Fine tuning for Best Performance There are a few choices the Administrator is allowed to maximize the capabilities of the Network Camera Best performance generally equates to the fastest image refresh rate with the best video quality and at the lowest network bandwidth as possible The three factors Maximum frame rate Fix bit rate and Fix quali
12. link on the configuration page to restore factory default settings Any changes made so far will be lost and the system will be reset to the initial factory settings After clicking on the Restore button and make confirmation the system will restart and require the installer program to set up the network again Calibrate Recalibrate the home position to the default center to recover the tolerance cased by some external forces This function is the same as the Center button on the Remote Controller Please note that there is no confirming message box after clicking on the Calibrate button the Network Camera will calibrate immediately 47 Appendix A Troubleshooting Status LED After powering up the Network Camera performs a self diagnostic to detect any hardware defects The following table lists the LED patterns in general In case of any fatal error the LED will blink in a pattern other than those below Condition LED color During self diagnostic after power on Blink in interchanged green and red Ethernet signal is lost Red LED is blinking till Ethernet is detected Before network is setup Steady green till IP address is confirmed After network is setup Blink green every second Any hardware failure Other patterns Reset and Restore i i i i m Nor a y E ee E f a Ik E m uas NRestoring the factory defaults will erase any previous settings Reset or re
13. must be filled Please input the hostname that is registered in the DDNS server Username E mail The Username or E mail field is necessary for logging in the DDNS server or notify the User of the new IP address Note when this field is input as Username the following field must be input as Password Password Key Please input the password or key to get the DDNS service Enable UPnP This turns on or off the UPnP function When UPnP is turned off the camera cannot be found through network neighbors in MS Windows XP If the UPnP network component is installed in Windows XP the hostname of the Network Camera will be shown with bracketed IP address in the Network neighbors Ex Network Camera with Pan Tilt 96 That is The hostname of the Network Camera is Network Camera with Pan Tilt and the IP address of the Network Camera is xxx xxx xxx 96 depends on the last value of the IP address assigned to the Network Camera Save Click on this button to save current settings for the DDNS service and UPnP function 46 Viewing System Log Click on the link on the configuration page to view the system log file The content of this file provides useful information about configuration and connections after system boot up Viewing System Parameters Click on this link on the configuration page to view the entire system s parameter set The content is the same as those in CONFIG INI Factory Default Factory default Click on this
14. user name on the external FTP server 1st FTP password Granted password on the external FTP server 1st FTP remote folder Granted folder on the external FTP server The string must conform to that of the external FTP server Some FTP servers cannot accept preceding slash symbol before the path without virtual path mapping Refer to the instructions for the external FTP server for details The folder privilege must be open for upload Primary FTP passive mode The Network Camera is located inside the network protected by a firewall data connection for FTP may be prohibited By selecting passive mode the FTP can bypass the rule and allow snapshot upload to proceed If the passive mode is selected the Network Camera can automatically attempt for active mode if the external FTP server does not support passive mode 2nd FTP server The domain name or IP address of the backup external FTP server 2nd FTP user name Granted user name on the backup FTP server 2nd FTP password Granted password on the backup FTP server 2nd FTP remote folder Granted folder on the backup FTP server Secondary FTP passive mode Passive mode setting for the backup FTP server 37 Some invalid settings may cause the system failing to respond Change the configuration only if necessary and consult with your network supervisor or experienced users for correct settings Once the system has lost contact refer to Appendix A for reset and restore procedures
15. when I set up some options in the application Al Since the Network Camera is a network camera any incorrect network settings will make it inaccessible If this happens restore the factory default settings following the procedures in Appendix A 51 C URL Commands of the Network Camera For some customers who already have their own web site or web control application the Network Camera can be easily integrated through convenient URLs This section lists the commands in URL format corresponding to the basic functions of the Network Camera Capture Update Snapshot of JPEG Image cgi bin video jpg The Network Camera will return the most up to date snapshot in JPEG format Query Status of the Digital Input cgi bin getdi cgi The Network Camera will return the status of digital input Drive the Digital Output cgi bin setdo cgi do lt state gt The state is either h or I h means high that is NC is connected with COMMON and I means low that is NO is connected with COMMON For instance typing http 192 168 0 201 cgi bin setdo cgi do h in the address bar of the web browser will command the Network Camera with IP address of 192 168 0 201 to set digital output to connect to NC with COMMON Restore Factory Default Settings setup restore cgi The Network Camera will automatically restart after restoring factory default configurations 52 Restart System setup reset cgi Restart the N
16. you to the client setting pages please check the following session for more details Configuration Only the Administrator can access camera configurations The camera view The information bar at the top of the camera view shows the connection type to the Network Camera and the current date time The camera view provides not only the live video but also a way to aim the Network Camera to different target Using mouse to click on the target inside the video will command the Network Camera to aim at the target Zoom This feature allows users to open a digital zoom control window to specify the zoom factor for specified area in the camera view Users can also move the white frame to select the area of the video that she he wants to view a LevelOne WCS 2010 P T IP Camera Microsoft Internet Explorer ay ch uu x a A P Search ST Favorites QI Media e B 2 E Address http 192 168 10 193 v Sy Go Link Goto Select one v Sl Hide Disable digital zoom zoom Factors 155 Client Settings Done Internet 10 Disable digital zoom The checkbox selection allows users to disable enable the digital zoom function Zoom Factors The range of zoom factor is from 100 to 400 users can select any integer factor inside this area Hide Click on this button can close the digital zoom control window The pan tilt control buttons The direction buttons are for Left
17. 0 Yes They may be from the O0 02 D1 00 00 12 192 168 0 186 Yes 00 02 D T DO OD 1 7 132 158 1 131 Yes DHCP server If there is O0 02 D1 00 00 10 192 168 0184 Yes 00 02 07 00 00 11 132 158 0 3 Ma no DHCP server the camera will try to find a free IP address this takes from 15 second to 3 Link to selected device Search minutes depending on the LAN status The Selected device This server has already been assigned IP method of findi ng IP Enter the IP address vou want to assign and click the Set IP Address button address is seeking from 192 168 0 99 to 192 168 0 254 If any of Check this option will skip installation the address inside this procedure whenever the device starts up range is free the Network Camera will be assigned to this IP and its subnet mask would be 255 255 255 0 If none of the addresses is free the Network Camera will try the range from 192 168 0 2 to 192 168 0 98 After an IP address is assigned to the camera the Activity status LED blinks The LevelOne s new f IP Installer UPnP function will Please restart your device and select one by IP Installer a Iways assig n an IP clicking the serial number Version 2 0 address for the Network Series Number Curent IP Address Assigned iB 1921580190 Yes Camera The O0 02 01 00 00 12 192 168 0 186 Yes un l O0 02 01 00 00 17 192168 0 191 Yes Administrator can click O0 02 01 00 00 10 192 168 0 184 Yes 00 02 01 00 00 11 19
18. 2 168 0 9 Ma on button Link to selected device to connect the I E to the camera Link ta zelected device Search If the camera is not on the IP insta ler list Cl ick Selected device This server has already been assigned IP on the Search button Enter the IF address you want to assign and click the Set IP Address button to search for the 18 189 OT camera on the LAN E Check this option will skip installation procedure whenever the device starts up For the series number in the Serial Number field please check the label on the bottom of the camera It is the same i O as the MAC address M Initial Access to the Network Camera Check Network Settings The Network Camera can be connected either before or immediately after software installation onto the Local Area Network The Administrator should complete the network settings on the configuration page including the correct Subnet mask and IP address of gateway and DNS Ask your network administrator or Internet service provider for the detail information By default the Network Camera requires the Administrator to run installation every time it reboots If the network settings are to remain unchanged disable the Install option Refer to Network settings on the System Configuration page for details If any setting is entered incorrectly and cannot proceed to setting up the Network Camera restore the factory settings following the steps in the
19. 61 Application Configuration URL URL setup app cgi smethod event post event condition condition condition matched mdalarm lt not required gt trigger DO when motion detected ioupload lt not required gt upload snapshot when DI condition matched 62 detected mode Sbegin hh mm ss time to start sequential mode send ___ lt hh mm ss gt time to stop sequential mode 63
20. 7 netkey2 hexadecimal string 00 FF network key 2 netkey3 hexadecimal string 00 FF jnetwork key 3 netkey4 hexadecimal string 00 FF Inetwork key 4 Hexadecimal string means the string is composed of two digit ASCII code indicating the hexadecimal value For example if the network key is abcdefg in ASCII format the hexadecimal string will be 6162636465666 7 I DDNS amp UPnP Configuration URL URL A setup ddns cgi NAME VALUE DESCRIPTION enddns anything Enable DDNS function This option must be Uem whenever the URL is called if DDNS function is to be enabled provider email address registered in DDNS server passkey password or key The login password of DDNS server or the key Pr emet a enupnp janything Enable UPnP function This option must be oem whenever the URL is called if UPnP function is to be enabled Mail amp FTP Configuration URL URL setup mailftp cgi NAME VALUE DESCRIPTION smtp1 domain name or IP primary SMTP server address mailto1 string shorter than 80 mail recipient address characters mailnamel max 14 characters irst account name in SMTP server 58 server address gt characters gt server server characters gt ftpp number less than 65535 FTP port address characters characters characters server address characters server ftppass2 a for secondary FTP characters gt server ftpfolder2 lt text string shorte
21. amera for the first time using Internet Explorer adjust the security level of Internet Explorer to allow installation of plug ins 3 If the problem still exists after adjusting and the message over the image window is showing connecting the network traffic may be too crowded Q What is the plug in for Al The plug in provided by the Network Camera is used to display motion pictures and audio in Internet Explorer If your system does not allow installation of any plug in software the security level of the web browser may need to be lowered It is recommended that you consult your network Supervisors in your office regarding adjustment of the security level Software installation may be regulated in some offices Q Why is the timestamp different from the system time of my PC or notebook A The timestamp is based on the system time of the Network Camera It is maintained by a real time clock inside and can be automatically synchronized with the time server if the Network Camera is connected to the Internet and the function is enabled Differences of several hours may result from the time zone setting Q Can I install it on ceiling 49 Al Yes There are flip and mirror options in the video configuration page to correct the images for upside down installation Q The image is not clear enough Al Rotate the lens to adjust the focus after the Network Camera has been installed in the proper position The image settings and white balance c
22. an be fine tuned to achieve the best visual effect Also notice the power line frequency must match the local utility to synchronize and minimize the effect of flickering florescent lights Q Why does the image not refresh regularly Al Some anti virus programs filter the received web content It takes time to perform data examination and affect the streaming application such as that of the Network Camera However it only affects the HTP mode of the Network Camera If the network allows only HTTP mode disable the web filtering function of the anti virus program temporarily During this period the User Should be aware of the risk of malicious network activity Q I have opened motion detection windows but it cannot work Al If the motion detection windows are set up and names are given check to see if the function is checked on the first line While it is enabled adjust the sensitivity and percentage to monitor the level indicator for best results Q I cannot hear any sound while watching Al If there is V_ONLY shown above the image click on connection type to uncheck Disable audio If there is V shown instead of AV the sound card in your PC may not have been properly installed If AV is shown check the audio source of the Network Camera make sure you are using internal or external microphone Q How many users are allowed to watch the Network Camera at the same time Al Too many users requesting the real time multimedia conte
23. and MAC number as password Connect to 192 168 0 99 Levelone WiCS z 10 PIT IP Camera User name root v Remember my password 26 4 After log on to the camera please click Configuration button e LevelOne WCS 2010 P T IP Camera 2004 06 25 04 25 34 PM Go to Select one Pan speed o Tilt speed o A zoom m or Tro Digital Output ON OFF Snapshot 5 Select Network linkage in left frame Once entering to the network page please execute the following step 5 1 Disable the Reset the IP address at next boot option 5 2 Change the IP address you want 5 3 Click Save button to save the modified information u J 0 HOME System ir Security 5 gt Network IP address 5 2 gt Mail amp FTP Subnet mask 255 255 255 0 b DONS amp UPnP Default rauter 192 168 0 5 b Audio Video Primary DNS 168 935 1 1 amp Camera control Secondary DNS 192 168 0 7 gt l Motion detection HTTP gt Application HTTP port an mj View log file Streaming B View parameters Control channel port 5001 amp Factory default Video channel port 5003 Audio channel port 5002 27 6 Launch the Upgrade Wizard from your CDROM EH EH orade Wizard Application EH BH Disital Data Communications Asia 7 Type the Camera s IP address amp root s password which you have to upgrade its firmware Then click Next button llpzrade Wizard With power
24. anyone who types in demo as user name No password is needed for demo account Note that a demo account is restricted to view only Allow more viewers with snapshot mode There can only be a maximum of 10 users to simultaneously view the video This option allows for the 11 viewer on the overloaded viewers to see only still images These still images are automatically refreshed by the interval defined below This feature must be supported by the java script capability of the web browsers Snapshot interval defines the refresh rate of the still image in the homepage seen by the overloaded viewers 33 Network Settings Any changes made on this page will restart the system in order to validate the changes Make sure every field is entered correctly before clicking on Sae Reset IP address at next boot the default status is checked to avoid erroneous entries during installation This can be tedious having to perform software installation whenever the Network Camera starts Therefore once the network settings especially the IP address have been entered correctly uncheck this option If this option is disabled the Network Camera will skip installation at the next boot The Network Camera can automatically restart and operate normally after a power outage Users can run IP installer to check the IP address assigned to the Network Camera if the IP address is forgotten or using the UPnP function provided by the Network Camera MS Wi
25. applied to the device enter the device IP address and root password click an Next below Depending on the communication environment the procedure can take up to 1 minutae IF address 192 488 T 102 ettr tetett reer 1 root password Cancel version 1 1 7 1 If the root s password or Video Server s FTP port is changed the dialog will pop up to ask VM rr aue A merver eettmes x IF you have changed the server FTP port or root password Please input the correct settings Server FTP Port 21 Server root password poss 8 Specify the firmware location or click Browse button to select the firmware location Then click Next button Upgrade Wizard The updated device is WCS 2010 5 N 000201 O000F 1 Please enter the full path or browse the firmware file name for update File name Browse version 1 1 28 9 After clicking the Next button the program will check if the firmware is compatible with the Video Server and pop up the message dialog to ask If the firmware version is correct click Yes button i Upgrade Wizard The updated device ig Wo The firmware version you directed iz Please enter the Full path i PT 27 e4 L LO 0100b Upgrade it File name CD version 1 1 10 Then the firmware will start to upload the firmware to Video server The process bar will indicate current status Illpzrade Wizard WTnting Flash Ham naw please wait EE
26. bandwidth environment If the Network Camera seems to work in a low bandwidth network environment the User can use this option to see if audio quality can be improved by sacrificing some real time synchronization WLAN Configuration SSID Service Set Identifier it is a name that identifies a wireless network Access Points and wireless clients attempting to connect to a specific WLAN Wireless Local Area Network must use the same SSID The default setting is default Note The maximum length of SSID is 32 single byte characters and SSID can t be any of lt gt and space character Wireless mode Clicking on the pull down menu to select from the following options Infrastructure Make the Network Camera connect to the WLAN via an Access Point The default setting Ad Hoc Make the Network Camera connect directly to a host equipped with a wireless adapter in a peer to peer environment Channel While in infrastructure mode the channel is selected automatically to match the channel setting for the selected Access Point In Ad Hoc mode the channel must be manually set to the same channel for each wireless adapter The default channel setting depends on the installed region TX rate This field is for selecting the maximum transmission rate on the network The default setting is auto that is the Network Camera will try to connect to the other wireless device with highest transmitting rate Prea
27. c which must handle the picture refreshing from the Network Camera If the web server space has FTP service set the Network Camera up as an FTP 17 client to upload the pictures The access to the Network Camera will be independent of the number of viewers and the picture quality will remain constant 1 Click on Configuration on the homepage 2 Click on Network in the left column 3 Fill in the FTP related settings including server user name and password as well as the upload path if it is specified by the web space and click on Save button HOME Weekly schedule System Osun Omon L rue Owed OThu Ceri Sat Security snapshots begin at 00 00 00 hh mm ss fe Network snapshots stop at 00 00 00 hh mm ss m Mail amp FTP All the time except for the above schedule DONS amp UPnP Event operation a Audio Video General el Camera control Delay 3 second s before detecting the next event ie Motion detection Take snapshot at 1 secondi after event s Application Trigger condition View log file input is high LJ Input is law Input is rising LJ Input is falling Bj view parameters Detect motion in amp Factory default undefined Undefined Undefined Mate Motion detection must be setup first version 0100d Trigger action C Trigger output alarm while input condition matched C Trigger output alarm while motion detected C Upload snapshots while input condition matched C Upload
28. d set the maximum frame rate to 25 fps or 30 fps If you are shooting fast moving images you may want to slow the maximum frame rate down to 20 fps in order to lower the rate of data transmission This allows for better video quality and the human eyes cannot readily detect the differences between those of 20 25 or 30 frames per second If your network bandwidth is below 384 Kbps set the Fix bit rate according to your bandwidth and try to get the best performance by fine tuning with the Maximum frame rate In a slow network greater frame rate results in blur images Another work around is to choose Half in the Size option for better images or Halfx2 for a larger image view Video quality performance will vary somewhat due to the number of users viewing on the network even when the parameters have initially been finely tuned Performance will also suffer due to poor connectivity because of the network s burst constraint Only Quality Images Will Do To have the best video quality you should set Fix quality at Detailed or Excellent and adjust the Maximum frame rate to match your network s bandwidth If your network is slow and you receive broken pictures go to the TCP protocol in Connection type and choose a more appropriate mode of transmission The images may suffer a time delay due to a slower connection The delay will also increase with added number of users Somewhere B
29. e External microphone Video Text on Video Color COLOR v Size Normal Maximum frame rate 30 iM Video quality contral Fix bit rate 384Kbps w Fix quality Good Flip Mirror Image Settings Save 40 Motion Detection Enable motion detection Check this option to turn on motion detection New Click on this button to add a new window At most three windows can exist simultaneously Use the mouse to click hold and drag the window frame to resize or the title bar to move Clicking on the x at the upper right hand corner of the window to delete the window Remember to save in order to validate the changes Save Click on this button to save the related window settings A graphic bar will rise or fall depending on the image variations A green bar means the image variation is under monitoring level and a red bar means the image variation is over monitoring level When the bar goes red the detected window will also be outlined in red Going back to the homepage the monitored window is hidden but the red frame shows when motion is detected Window Name The text will show at the top of the window Sensitivity This sets the endurable difference between two sequential images Percentage This sets the space ratio of moving objects in the monitoring window Higher sensitivity and small percentage will allow easier motion detection The following figure shows the screen when Sae
30. e leve LevelOne WCS 2010 11g Wireless P T Network Camera User s Manual O Power off the Network Camera Keep the Network Camera as soon as it is found away from the water If the smoking or smelt unusual Network Camera is wet power off immediately Contact your distributor when such cases happen f Contact your distributor when such cases happen i 1 a Do not place the Network O Refer to your user s manual Camera around the heat for the operating temperature sources such as television or oven Keep the Network Camera O Do not place the Network away from the direct Camera in high humid sunlight environments EN d s a E ODo not place the Network Camera on unsteady surfaces m4 fi a S i 1 i 5 BN e n S a LEM Rue c Do not disassemble the Network Camera Do not manually pan and tilt the Network Camera when the power is on E LI Soe F af J pP ES m ri rm i id B E wen ij h Ea m S __ Jf E a D oa F Z z te lH F4 E kn y Do not touch the Network Camera when it s lightening Do not drop the Network Camera ODo not insert any object into the Network Camera such as needles Package Contents Network Camera Power adapter with Pan Tilt Camera stand OAIV cable Software CD O Antennas dure Ii Table of Contents Installation Hard
31. e with SW_OPEN when DO is set to ON OUTPUT Max 1A 24VDC or 0 5A 125VAC Software Installation In this manual User refers to whoever has access to the Network Camera and Administrator refers to the person who can configure the Network Camera and grant user access to the camera At the end of the hardware installation the Administrator must place the product software CD into the CD ROM drive of the PC running in MS Windows An auto run program will pop up If the program is not on auto run go to the root directory of the software CD and click on autorun exe Z a m PES p i s HI j N 151 1 One one worlLd one LevelOne WCS 2010 Wireless Pan Tilt IP Camera Utility Upgrade Wizard Close Click on the IP installer and run LevelOne s Installation program Install the Network Camera on Ethernet before install it on WLAN Refer to the network setting chapter to setup wireless network parameters Upon IP installer s start up a searching box will STE pop up This program searches for LevelOne s product on the same LAN Searching devices please wait After searching the LAN the main window of IP installer will pop up The IP addresses shown IP Installer in the Current IP Please restart your device and select one by IF Installer Add ress field reflect clicking the serial number Verzi ersion 3 0 those on the local network Series Number Curent IP Address Assigned SRR RE 192168015
32. ering via external voltage input rising falling is for edge triggering There are three windows for motion detection each can be assigned a name If motion detection has not been set up undefined will be shown instead of the window title If this happens clicking on Motion detection and a note will show to direct the User to the configuration page for motion detection Trigger action There are four options for two types of action More than one condition can be selected at once While choosing to trigger an output alarm the digital output will short both pins and complete the external device s circuit The normal state is open Either email or FTP can be used to command uploading snapshots The snapshot names will be vpre jpg vtrg jpg and vpos jpg respectively They stand for the snapshots before event right upon event and after event The date and time suffix may also be added as an option Confirm the external mail or FTP server settings in the network configuration 42 Reset output Select and save this option to reset the external device at the digital output to return to the original state Sequential Operation Snapshot every second s The Network Camera will send snapshots at the specified intervals to the external server using the method selected below Remember This operation is still subject to the conditions set in the weekly schedule Send snapshots by email Thi
33. et whenever the Network Camera starts up It will fail if the assigned time server cannot be reached NTP server Assign the IP address or domain name of the time server Leaving the text box blank connects the Network Camera to the default time servers Time zone Adjust the time with that of the time servers for local settings Update interval Select hourly daily weekly or monthly update with the time on the NTP server Remember to click on e to immediately validate the changes Otherwise the correct time will not be synchronized 32 User Group Administration Root password Change the Administrator s password by typing in the new password identically in both text boxes The typed entries will be displayed as asterisks for security purposes After pressing Save the web browser will ask the Administrator for the new password for access Add user Type the new user s name and password and press Add to insert the new entry The new user will be displayed in the user name list There is a maximum of twenty user accounts Each user can have the privilege to Permit for I O control and Permit for PT control Delete user Pull down the user list to find the user s name and press Dete to complete Permit for I O control Allows user to control the DO and get status of the DI Permit for PT control Allows user to aim the Network Camera to different targets Allow demo account to view Check this to permit
34. etween Real time and Clear Images If you have a broadband network set Fix quality at Normal or better rather than setting Fix bit rate You can also fix the bandwidth according to your actual network speed and adjust the frame rate Start from 30 fps down for best results but not below 15 fps If the image qualities are not improved select a lower bandwidth setting Viewing Double size image The Network Camera not only provide standard CIF SIF format video but also provide 4CIF 4SIF format video For selecting Double video size the video from the Network Camera can provide more details but less frame rate up to 10 frames sec Besides Normal x 2 selection will do 200 digital zoom for both the width and height of the video 15 Opening Accounts for New Users Protect Network Camera by passwords E http 192 168 10 193 setup config html Microsoft Internet Explorer File Edit view Favorites Tools Help w Back j x a 5 J9 Search gr Favorites ea Media vr Z Address E http 192 168 10 193 setup config html v Go Links one HOME System Root password gt Security Blank root password will disable user authentication gt Network Root password eeeeeececce gt Mail amp FTP Confirm password eeeseeceese gt DDNS amp UPnP i gt Audio Video f Add user gt Camera control User name Motion detection t2 User password OOO Application l C Per
35. etwork Camera without warning 53 Page URL The configuration page has a frame layout including an option list frame and an option page frame Referenced URLs except for the configuration page direct users to the option page frame only Some pages such as image quality setting and preset setting are opened in new windows for preview Only the Administrator can access these URLs configuration page ig System Resource URL There are some images used on the homepage when the homepage layout is in image mode The Administrator may use the following links to show the images saved in the Network Camera on another page system logo image pic logo gif background image pic wallppr jpg General Format of Command URL Every configuration can be set through URL with the POST method by the Administrator only 54 lt general format gt URL name value amp name value lt method gt POST lt authorized user gt root System Configuration URL URL setup system cgi by slash separated by colon ntp lt domain name or IP address gt updateintervallone hour Synchronize with NTP hourly 55 Security Configuration URL URL setup security cgi NAME VALUE DESCRIPTION characters gt characters gt characters gt deluser text string shorter than 15 existing user name characters eo pes _permission for DIDO access _ Network Configuration URL URL setup network cgi ip
36. he other wireless device the red LED will become lighted Operating in either network mode the green LED will flash every second as heartbeat to indicate alive To install in Ethernet Make sure the Ethernet is firmly connected to a switch hub After attaching the Ethernet cable plug in the power adapter If the LED turns out to be steady green after self test go to next paragraph Software installation If the Ethernet is not available Network Camera will switch to wireless LAN mode To install in wireless LAN If the Ethernet is not available while power on the Network Camera will search for any access point with the SSID default Once any access point is found the LED will turn green to wait for installation If the network environment cannot meet the default settings install Network Camera in Ethernet to proceed with wireless LAN configuration The Network Camera provides a general I O terminal block with one digital input and one relay switch for device control Pin 1 and Pin 2 can be connected to an external sensor device and the state of voltage can be monitored from the initial state LOW The relay switches Pin 3 and Pin 4 can be used to turn on or off an external device 4 Consult with the dealer of the peripherals for correct installation 4 3 2 1 41 KOO DOU DI DI SW_COMMON SW_NOPEN INPUT Max 50mA 12VDC INPUT Initial state of DI is Low OUTPUT open from SW_OPEN at initial state clos
37. ilding a Security Application The Administrator can combine options on the application page to perform many useful security applications There are two trigger sources coming from attached devices such as for motion detection There are also two kinds of actions responding to such events including uploading snapshots over the Internet and driving other attached devices To upload the snapshots the User can choose either email or FTP according to user s needs Both e mail and FTP use the network settings on the network page Refer to the definition section for detail configuration LevelOne WCS 2010 P T IP Camera HOME eekly schedule gt System Osun Omon OTue Owed Thu Ofri C Sat gt Security snapshots begin at 00 00 00 hh mm ss Network snapshots stop at 00 00 00 hh mm ss gt Mail amp FTP C All the time except for the above schedule a DDNS amp UPnP Event opc i Audio Video General 4 Camera control Delay 3 second s before detecting the next event Motion detection Take snapshot at 1 second s after event Application Trigger condition View log file Input is high Input is low Input is rising Cl Input is falling amp View parameters Detect motion in amp Factory default undefined C Undefined C Undefined Note Motion detection must be setup first Version 0100d Trigger action C Trigger output alarm while input condition matched C Trigger output alarm while motion detected CI Upl
38. is clicked B LevelOne WCS 2010 P T IP Camera HOME Enable motion detection f System b Security Window Name gt Network porti b Mail amp FTP Sensitivity DDNS amp UPnP 60 B Audio Video JOrt Motion Detection ig Camera control a Save window completed 2 F 59 4 Motion detection 7 Application i gt View log file l gt View parameters New Save Factory default Version 0100d amp Done 41 Application Setup Weekly Schedule Sun Sat Select the days of the week to perform the following operations Snapshots begin at Set the time to start operations Snapshots stop at Set the time to stop operations Setting identical begin time and stop time means 24 hour operation Event Operation Delay second s before detecting next event Set the time delay before restarting to check on the triggering condition when the current condition is triggered Take snapshots at second s after event After the camera has taken a Snapshot when a condition is triggered another snapshot will be taken after this configured interval in seconds Trigger condition There are four conditions relative to the digital input and the three windows for motion detection More than one condition can be selected at once Select the appropriate digital input condition that suits the characteristics of the external device high low selects level trigg
39. ist for preset positions Clicking on the Delete button will remove the current selected position from the preset list Dwelling time The value set here specifies 1 The stop time of each preset location during auto patrol of the Network Camera 2 The stay time at the most left and the most right positions when the Network Camera is doing auto panning Patrol selection After the User has saved a list of preset positions the Preset locations box will also keep a list of the preset positions And once the Select gt button is clicked the Selected location box will keep a list of the patrol stops The Remove button removes the preset position from the patrol stops The UP DOWN buttons adjust the order of the patrol stops Several preset positions can be added to the patrol stops The camera can accept up to 40 patrol stops Save button The button is valid for Pan speed Tilt speed Auto pan patrol speed Enable IR control Dwelling time and Patrol selections In other words after changing these settings and the Save button is not clicked the new setting of the camera will not take effect 45 UPnP and DDNS Settings Enable DDNS This option turns on the DDNS function Provider The provider list contains four hosts that provide DDNS services Please connect to the service provider s website to make sure the service charges Host name If the User wants to use DDNS service this field
40. ler objects 13 Clicking on Save enables the activity display Green means the motion in the window is under the watermark set by the Administrator and red means it is over the watermark 14 Click on Application in the left column 15 Check on the window name set in Step 10 16 Check Upload snapshots while motion detected if e mailing the Snapshots is preferred 17 Check Send snapshots by email 18 Click on Save to validate 23 Software Revision Upgrade Customers can obtain the up to date software from the web site of LevelOne www levell com An easy to use Upgrade Wizard is provided to upgrade the Network Camera with just a few clicks The upgrade function is opened to the Administrator only To upgrade the system follow the procedures below 1 Download the software file named FLASH BIN from the appropriate product folder 2 Run the Upgrade Wizard and proceed following the prompts Refer to the instructions of the Upgrade Wizard for details 3 The whole process will finish in a few minutes and it will automatically restart the system S if power fails during the writing process of Flash memory the program in the memory of the Network Camera may be destroyed permanently If the Network Camera cannot restart properly ask your dealer for technical service 24 Multi Language by Software Upgrade The software in WCS 2010 Network Camera is four language English German Korean and
41. mble either Long preamble or Short preamble defines the length of the CRC block Cyclic Redundancy Check is a common technique for 35 detecting data transmission errors for communication between the Access Point and the roaming wireless device Long Preamble is the default setting Note High network traffic areas should use the shorter preamble type Data encryption Checking the box to enable the data encryption By default it is disabled Auth Mode Choosing one of the following modes Open is the default setting e Auto The selection will apply both Shared and Open mode authentication method this is the most strict mode of all e Shared allows communication only with other devices with identical WEP settings e Open communicates the key across the network Key length The administrator can select the key length among 64 or 128 bits 64bits is the default setting Key format Hexadecimal or ASCII HEX is the default setting e HEX digits consist of the numbers 0 9 and the letters A F e ASCII is a code for representing English letters as numbers from 0 127 except and space characters that are reserved Network Key Entering a key in either hexadecimal or ASCII format When selecting different key length acceptable input length is listed as following 64 bits key length 10 Hex digits or 5 characters 128 bites key length 26 Hex digits or 13 character
42. mission for 1 0 control View log file a C Permission for PT control Add gt View parameters Factory default Delete user Version 0100d User name no user v Allow demo account to view Allow more guests with snapshot mode Snapshot interval 10 Second s amp 4B Internet Network Camera is shipped without any password by default That means everyone can access Network Camera including the configuration as long as the IP address is known It is necessary to assign a password if the Network Camera is intended to be accessed by others Type a new word twice in to enable protection This password is used to identify the administrator Then add an account with user name and password for your friends in Network Camera can provide twenty accounts for your valuable customers or friends Each account identifies the access right rather than the real visitor That allows multiple visitors share the same account of different level An option to access DI DO is provided for each account Some users may need to prohibit from controlling your attached devices Another option allows different control to pan tilt functions of the Network Camera You may delete some users from O More flexible options for viewers The first option allows anyone uses demo as the user name to view without 16 password The Administrator can also decide if more viewers are allowed to watch the video if the viewers exceed the limit The o
43. ndows XP provides UPnP function at Network Neighbors General IP address This is necessary for network identification Subnet mask This is used to determine if the destination is in the same subnet The default value is 255 255 255 0 Default router This is the gateway used to forward frames to destinations in a different subnet Invalid router setting will fail the transmission to destinations in different subnet Primary DNS The primary domain name server that translates hostnames into IP addresses Secondary DNS Secondary domain name server that backups the Primary DNS HTTP Http port This can be other than the default Port 80 Once the port is changed the User must be notified the change for the connection to be successful For instance when the Administrator changes the HTTP port of the Network Camera whose IP address is 192 168 0 100 from 80 to 8080 the User must type in the web browser http 192 168 0 100 8080 instead of 34 http 192 168 0 100 Streaming Control channel port This can be something other than the default port 5001 in order to work with the port opened by the firewall Audio channel port This can be something other than the default port 5002 in order to work with the port opened by the firewall Video channel port This can be something other than the default port 5003 in order to work with the port opened by the firewall Improve audio quality in low
44. nience This option is not available to the Administrator for obvious reason 3 Mic rosoft Internet Explorer e L x a A pP Search Sf Favorites QU Media E2 Connect to 192 168 10 193 N LevelOne WCS 2010 P T IP Camera User name Password Remember my password kd Web site Found Waiting For reply TJ Installing Plug in For the initial access to the Network Camera in Windows the web browser may prompt for permission to install a new plug in for the Network Camera Permission request depends on the Internet security settings of the user s PC or notebook If the highest security level is set the computer may prohibit any installation and execution attempt This plug in has been registered for certificate and is used to display the video in the browser Users may click on to proceed If the web browser does not allow the user to continue to install check the Internet security option and lower the security levels or contact your IT or networking supervisor for help AB LevslDie WiCS 2000 2 T E Camera Miczosoft Iate met 3splocer E jax TEE Ga K ceux Aleea TACS HEH 3 wo 3 QO 4 Gs ufeRE Jus GR E c9 RN H i AED LevelOne WCS 2010 P T IP Camera Do vou want bo inztal and run MPEGS SHM uda Caria agred an 1 28 2004 50 PM and disnbuted bi Digital Data Communications Asie Co Lid m Publisher aulhenkicty verified by VeriSign Class 3 Code Ga rn
45. nt will jam the network For best results the Network Camera is designed to accommodate a maximum of ten 10 users to watch and listen at the same time For a larger number of users it is recommended to build another web server to host the retrieved contents from the Network Camera Q How fast is the video rate of the Network Camera 50 Al The MPEG4 codec engine can process up to 30 frames per second internally However the total performance is subject to many coefficients such as 1 Network throughput 2 Bandwidth share 3 Number of users 4 The complicated detailed objects and movement in view 5 The power of your PC or notebook computer that is responsible for displaying images In general the transfer rate in a general local network environment can achieve over 200 kilobytes per second and approximately 10 to 20 pictures per second from a regular environment Q How can I keep the Network Camera as private as possible Al The Network Camera is designed for surveillance purposes and has many flexible interfaces The user authentication and special confirmation in installation can keep the Network Camera from unauthorized access You may also change the HTTP port to a non public number The demo account is good to separate guests from normal users and thus you can easily block the guests anytime You can check the system log to examine any abnormal activities and trace the origins Q Why can I not access the Network Camera
46. oad snapshots while input condition matched CI Upload snapshots while motion detected Reset output Sequential operation Snapshot every 0 second s Done 4B Internet 1 Click on Configuration on homepage 2 Click on Application in the left column 3 Check the weekdays as you need and give the period of Snapshots begin time and Snapshots end time to monitor the triggering conditions every day 4 Check the Event operation The triggering condition can be set to detected motion or status of the attached device 5 Set the delay before detecting next event to avoid continuous false alarms following the original event 6 Set the delay to take snapshots after event to capture the direction of the moving objects 21 9j RI Rm iR ie i i RJ ER i 9j iw HOME System Security Network Mail amp FTP DDNS amp UPnP Audio Video Camera control Motion detection Application View log file View parameters Factory default o I o e p a e a amp Done Configuration C All the time except for the above schedule Cl Event operation General Delay 3 second s before detecting the next event Take snapshot at second s after event Trigger condition CJ Input is high Cl Input is low Cl Input is rising O Input is falling Detect motion in lundefined C Undefined C Undefined Note Motion detection must be setup first Trigger action CI Trigger output alarm while input c
47. ondition matched CI Trigger output alarm while motion detected CI upload snapshots while input condition matched C Upload snapshots while motion detected C Reset output Sequential operation Send snapshots by email 9 Send snapshots by FTP v FTP put snapshots with date and time suffix 8B Internet Send Snapshots When Motion is Detected If no external sensor is available the Administrator can use the built in motion detection to monitor any movement and sends snapshots via email for security check Configuration View parameters mm HOME Enable motion detection gt System gt Security Window Name gt Network porti gt Mail amp FTP Sensitivity 5 DONS amp UPnP e 9m b Audio Video b Camera control bic 3 o Motion detection Application i View log file gt gt Factory default lt BU x 2 o e n ae e e 4D Internet g Done 7 Click on Motion detection in the left column 22 8 Check Enable motion detection 9 Click on New to have a new window to monitor video 10 Type in a name to identify the new window 11 Use the mouse to click hold and drag the window corner to resize or the title bar to move 12 Fine tune using the Sensitivity and Percentage fields to best suit the camera s environment Higher Sensitivity detects the slighter motion Higher Percentage discriminates smal
48. plorer Q es cJ x ie 5 P Search ST Favorites GA media C3 au Address http 192 168 10 193 client html v Eje ue Security Warning Do you want to install and run MPEG4 SHM Client Settings signed on 6 28 2004 6 49 PM and distributed by Digital Data Communications Asia Co Ltd Publisher authenticity verified by VeriSign Class 3 Code Signing 2001 CA Caution Digital Data Communications amp sia Co Ltd asserts that this content is safe You should only install view this content if you trust Digital Data Communications Asia Co Ltd to make that assertion Cl Always trust content from Digital Data Communications Asia Co Ltd Yes More Info amp Opening page http 192 168 10 193 client html M Internet There are two settings for the Client site One is Media Option for the User to determine if audio should be muted The other is Protocol Option which allows choices on connection protocol between client and server There are three protocol choices to optimize your usage UDP TCP and HTTP The UDP protocol allows for more real time audio and video streams However some packets may be lost due to network burst traffic and images may be obscured The TCP protocol allows for less packet loss and produce a more accurate video display The downside with this protocol is that the real time effect is worse 12 than that with the UDP protocol The HTTP protocol must be selected
49. ptimize bandwidth utilization and video quality If the User wants to fix the bandwidth utilization regardless of the video quality choose Fix bit rate and select the desired bandwidth The video quality may be poor due to the sending of maximal frame rate within the limited bandwidth when images are moving rapidly Consequently to ensure detailed video quality quantization rate regardless of the network it will utilize more bandwidth to send the maximal frames when images change drastically 39 Flip Vertically rotate the video Mirror Horizontally rotate the video Check options both if the Network Camera is installed upside down White balance Adjust the value for best color temperature Image Seting Click on this button to pop up another window to tune Brightness Contrast Hue and Saturation for video compensation Each field has eleven levels ranging from 5 to 5 The User may press preview to fine tune the image When the image is O K press to set the image settings see Click on this to recall the original settings without incorporating the changes m L2 M Pl HOME j System Security Network Mail amp FTF DONS amp UPnP Audiovideo Camera control Motion detection Application View log file View parameters Factory default Version 0100d Audio Mute improve audio quality in low bandwidth environment Audio source 9 Internal microphon
50. r than 40 upload folder in secondary FTP characters gt server Audio Video Configuration URL URL setup video cgi NAME VALUE DESCRIPTION text lt text string shorter than 15 j enclosed caption Icha racters gt size frame 1 2 J 3 Ooa 4 1 Ooa 5 double 440 9 B W monochrome 2 E o audiui 2 Jewerquaityofvideo 3 normalquality of video 4 Jhgherqualtyofvideo set bit rate to 512K bps E set maximum frame rate to 30 fps NTSC only flip image no normal image ye ms image normal image 60 mute anthing to turn off audio connections This will make the Network Camera reboot improve anthing to improve audio quality in low bandwidth environment this option must be resent whenever the URL is called if it is to be enabled mphone internal set the audio source from built in microphone external set the audio source from line in microphone Camera Control URL URL setup ptcamera cgi NAME VALUE DESCRIPTION addpos the position name add preset location with its name mee D position name delete preset location with its name selloc index value 019 add preset location into patrol list irenable yes enable the pan tilt control using remote controller no disable the pan tilt control using n n Speedapp 1 5 change the speed of auto pan or auto patrol Image Quality Configuration URL URL setup image cgi
51. s Note When 22 3C lt or 3E gt are input in network key the key format can t be changed to ASCII format Mail amp FTP SMTP SMTP mail server 1 The domain name or IP address of the external email server Recipient email address 1 The email address of the recipients for snapshots or log file Multiple recipients must be separated by semicolons SMTP account name 1 Some SMTP server requires an account name for logging in Refer to your SMTP administrator for detailed information SMTP password 1 The password for the SMTP server account 36 SMTP mail server 2 The domain name or IP address of another email server once the previous server is unreachable Recipient email address 2 The email addresses of the recipients for the backup server SMTP account name 2 The account login name for the second SMTP server SMTP password 2 The password for the second SMTP account name Return email address The return email address used in the event the mails fail to be sent out FTP Local FTP server port This can be other than the default Port 21 The user can change this value from 1 to 65535 After the change the external FTP client program must change the server port of connection accordingly 1st FTP server The domain name or the IP address of the external FTP server The following user settings must be correctly configured for remote access ist FTP user name Granted
52. s selects the uploading method following the intervals set above The snapshot named video jpg will be attached in the email with the subject title Periodic snapshots Send snapshots by FTP The snapshots will be uploaded to the external FTP server with the file name defined in the next option This can also be used to refresh the captured images stored in the external web server to build creative homepages FTP put snapshots with date and time suffix This option sets up the Snapshot capture date and time which can be used to easily differentiate the Snapshot file names in either the sequential or event operation For instance video 20030102030405 jpg means the JPEG image was captured in the year 2003 January the 2 at 3 o clock 4 minute and 5 second If this suffix is omitted the file named video jpg on the external FTP server will be refreshed at the specified interval 43 Camera Control HOME FOO4 07 15 11 55 38 35 ie System Security Network l Mail amp FTF f DONS amp UPnP a Left m Right Camera control Pan speed TilE speed Ji Auto pan patrol 1 speed BE tu 3 im TOM tu C n 3 T 5 Motion detection Application View log file View parameters A A amp amp M Enable IR control Current position Add Preset position m None Delete Dwelling time sec fo Patrol selection Factory
53. snapshots while motion detected Reset output Sequential operation Snapshot every i seconds O Send snapshots by email 9 Send snapshots by FTP FTP put snapshots with date and time suffix 4 Click on Application in the left column 5 Select the day or days of the week in Weekly schedule you want to upload the pictures 6 Select Sequential operation and set the interval 7 Unselect FTP put snapshots with date and time suffix as the upload method and click on Save 8 The image file uploaded to the web space is named video jpg Check if the file is successfully uploaded to the correct folder 9 Prepare a homepage with the embedded image reference to the image file 18 uploaded via FTP in advance If the web space has no FIP service An auto refresh homepage can be used to periodically poll the newest image from the Network Camera It is most efficient if using a free web space provider as the FTP service may be limiting 1 Prepare an auto refresh homepage as the following example The URL of image is http IP address of the Network Camera cgi bin video jpg Modify the IP address according to your Network Camera Define the refresh interval according to your network bandwidth for best result If the refresh rate is too fast and there is a large number of visitors this may overload the Network Camera and slows the response 19 Example of an auto refresh web page 20 Bu
54. store the system after power on At the left side of the camera there is a button hidden in the pinhole as shown in the picture It is used to reset the system or restore the factory default settings Sometimes resetting the system sets the system back to normal state If the system problems remain after reset restore the factory settings and install again RESET Poke the wrench to click on the button RESTORE 1 Poke the wrench to press on the button continuously 2 Wait for self diagnostic to run twice 3 Withdraw the wrench as soon as the second self diagnostic starts 48 B Frequently Asked Questions Q What if I forget my password Al After the Administrator s password has been assigned every access to the Network Camera needs authentication If you are one of the managed users you have to ask the Administrator for the password If you are the Administrator there is no way to recover the root password except by restoring the factory default settings Refer to Appendix A for the procedures Q Why can I not watch video from the Network Camera after it is authenticated Al There are many possible scenarios regarding this problem 1 If you have just installed the Network Camera and are unable to watch the video check if the heartbeat LED is blinking or the lens cap is off If the heartbeat LED is dim perform the software installation again 2 If the Network Camera is well installed and you are accessing the Network C
55. ty on the Video Configuration page are correlative to allow for achieving the best performance possible A http 192 168 10 193 setup config html Microsoft Internet Explorer fe X File Edit Yiew Favorites Tools Help a o Back x a 5 P Search Ke Favorites ea Media 697 2 E Address E http 192 168 10 193 setup config html v Go Links one NOME Audio Rhee rene mute B Security Improve audio quality in low bandwidth environment a Network i gt Mail amp FTP Audio source gt DDNS amp UPnP 9 Internal microphone 3 Audio Video External microphone Camera contral 2 gt Motion detection INQUAM Text on Video Application Color COLOR gt View log file Size Normal v gt View parameters Maximum frame rate 30 v Factory default g Y Video quality control O Fix bit rate 384 Kbps Version 0100d z 9 Fix quality Good v C Flip Mirror amp 8D Internet For Best Real time Video Images To achieve good real time visual effect the network bandwidth should be large enough to allow a transmission rate of greater than 20 image frames per second Ifthe broadband network is over 1 Mbps set the Fix bit rate to 1000Kbps or 1200Kbps or set Fix quality at the highest quality The maximum frame rate is 25 fps in a 50Hz system and 30 fps in a 60Hz system 14 If your network bandwidth is more than 384Kbps you can fix the bit rate according to your bandwidth an
56. verloaded viewers will have snapshot mode instead Building a Multimedia Web Attraction Site Demo on Multiple Sites Mid Scale Service The Network Camera can allow ten visitors to view on line simultaneously After Installation focus the Network Camera on any object you wish to share and tell the visitors to type in the web browser address Caution You may want to maintain your visitor s list in the security configuration page to block out unexpected visitors Product Demo for e Business Large Scale Service If the number of visitors has exceeded the limit the Network Camera can allow the overload viewers to see the snapshots in JPEG mode on the homepage These are still images and will be refreshed periodically and automatically It needs a script function supported by the web browser Version 0100a Delete user Username no user Delete Allow demo account to view Allow more guests with snapshot mode Snapshot interval 10 Second s 1 Click on Configuration on the homepage 2 Click on Security in the left column 3 Go to the bottom of the page and check off on Allow more viewers with Snapshot mode 4 Set the snapshot interval to refresh the still image automatically The longer the snapshot interval the better the snapshot mode works for multiple viewers If you want to expand to allow in more viewers the host server should be able to handle large network traffi
57. ware Installation Software Installation Initial Access to the Network Camera Check Network Settings Add Password to Prevent Unauthorized Access How to Use Authentication Installing Plug in Primary User s Capabilities Main Screen with Camera View Client Settings Administrator s Capabilities Fine tuning for Best Performance Opening Accounts for New Users Building a Multimedia Web Attraction Site Building a Security Application Building a Security Application Software Revision Upgrade Multi Language by Software Upgrade Definitions in Configuration System Parameters User Group Administration Network Settings General HTTP Streaming WLAN Configuration Mail amp FTP SMTP FTP Audio Video Codec Parameters Audio Parameters Video Parameters Motion Detection Application Setup O O ON JO OD DW FH e KF A U C WWW WW C0 WW C0 C0 WwW C NN NN YN N FH e KF FF Hc N e O O ON A AU UM BH AHAPWNeHE UH HBr ON WD HB AN Weekly Schedule Event Operation Sequential Operation Camera Control UPnP and DDNS Settings Viewing System Parameters Factory Default Appendix A Troubleshooting B Frequently Asked Questions C URL Commands of the Network Camera Capture Update Snapshot of JPEG Image Query Status of the Digital Input Drive the Digital Output Restore Factory Default Settings Restart System Page URL System Resource URL General Format of Command URL System Configuration URL Security Configuration URL Network Configuration URL
Download Pdf Manuals
Related Search