AI SPCA-GDH Greenwic..
Contents
1. D Left Pedestal Bottom Panel 1 E Left Pedestal Bottom Stretcher 2 F Left Pedestal Middle Crossbar 1 G Left Pedestal Back Panel 1 H Right Pedestal Left Panel 1 I Right Pedestal Right Panel 1 J Right Pedestal Bottom Panel 1 K Right Pedestal Bottom Stretcher 2 L Right Pedestal Middle Crossbar 1 M Right Pedestal Back Panel 1 N Pull out Tray 1 N1 Pull out Tray Molding 1 O Sliding Shelf 1 O1 Sliding Shelf Molding 1 P Modesty Panel 1 Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 4 Factory 16015 Model SPCA GDH Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly Q Door Panel 1 R Adjustable Shelf 1 S Utility Drawer Front 1 S1 Utility Drawer Back Panel 1 S2 Utility Drawer Left Side 1 S3 Utility Drawer Right Side 1 S4 Utility Drawer Bottom Panel 1 T File Drawer Front 1 T1 File Drawer Back Panel 1 T2 File Drawer Left Side 1 T3 File Drawer Right Side 1 T4 File Drawer Bottom Panel 1 U Guide Rail 2 V File Hanger 2 XL 12 Pull out Tray Left Slides 1 XR 12 Pull out Tray Right Slides 1 YL 14 Sliding Shelf Left Slides 1 Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 5 Factory 16015 Model SPCA GDH Parts a2. Stained surface Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 18 Factory 16015 Model SPCA GDH Assembly Instructions 46 Extend the Hinges Arms 14 and rest the Hinge Cups onto the cutouts of the Desk Door Panel Q Secure the Hinge Arms in place by using two 1 2 Zinc Screws 5 in each 47 Attach the Handle 12 to the front side of Door Panel Q with the provided Handle Bolts 13 48 Pick up the Door Panel Q and attach the extended Hinge Arms to the Hinge Bases installed on the Left Pedestal Left Panel B Loosen the bolt on the back of Hinge Base for an easy fit Align and insert the U slot on Hinge Arm under the bolt head on the back of Hinge Base Make sure that both door hinges engage and function properly Tighten the bolt on the Hinge Base to lock the hinges in place 49 Open and close the door to make sure it is aligned and shut correctly If necessary adjust the screws for a good fit wen 50 Insert the Shelf Pins 9 into the desired holes on the Left Pedestal Side Panels B and C Make sure you place the four Shelf Pins in the same level so the shelf is not tilted Tilt and rest the Adjustable Shelf R onto the Shelf Pins 9 with the finished edge facing forward Make sure that the end notches of the Shelf fit onto the Shelf Pins properly As shown Feed the cable of the USB Hub 11 through the large hole on Desk Top A and push the hub ove
3. Left and Right Side Panels H and I respectively with three 1 2 Black Screws 6 per slide track Ensure the slide opening faces the closest edge Tightly fasten with a Phillips screwdriver Mounting holes Mounting holes H i Slide opening Slide opening 31 Fasten the Left Pedestal Bottom Stretchers E to the Left Pedestal Bottom Panel D using two Wood Dowels 4 in each Make sure that the Cam Lock holes face inward 32 Pick up last assembly and attach it to the Left Pedestal Right Panel C using four Wood Dowels 4 and four Large Cam Locks 2 Make sure that the finished edge on the Bottom Panel D will face the front of the unit As shown 33 Align and attach Left Pedestal Middle Crossbar F to the Left Pedestal Right Panel C using one Wood Dowel 4 and one Large Cam Lock 2 Ensure the Cam Locks will face the floor 34 Repeat last two steps to attach the Left Pedestal Left Panel B at the other end it The finished edge faces Cam Locks will face the floor the front of the unit A ee i amp E Sx aa LE B D i 2 ee p G A 2 4 A gt Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 15 Factory 16015 Model SPCA GDH Assembly Instructions 35 Securely screw 2 Cam Bolts 3 into the designated small holes on the Right Pedestal Bottom Panel J as shown in the illustration 36 Align and attach the Right Pedestal Bottom Stretcher
4. N As shown below Slide opening Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 13 Factory 16015 Model SPCA GDH Assembly Instructions 26 Locate the Desk Top A the Left Pedestal Side Panels B and C and the Right Pedestal Side Panels H and I and securely screw the Cam Bolts 3 into the designated small holes as shown in the illustration N AIBICIHII 27 With the pilot holes as a guide fasten two Hinge Bases 14 to the Left Pedestal Left Side Panel B using two 1 2 Zinc Screws 5 per hinge As shown Make sure that the slot on the top of Hinge Base faces the closest edge 28 With the pilot holes as a guide align and attach the Left Slide Tracks CL to the Left Pedestal Left Side Panel B using three 1 2 Black Screws 6 through the small holes on the Track and screw into place Make sure the roller end of Slide Track faces forward Tightly fasten with a Phillips screwdriver 29 Repeat last step to attach the Right Slide Tracks CR to the Left Pedestal Right Panel C CLICR Roller is bottom Mounting holes 3 Roller is bottom The slot faces the closest edge Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 14 Factory 16015 Model SPCA GDH Assembly Instructions 30 Using the pilot holes as a guide attach the separated Slide Tracks YL YR and Z to the Right Pedestal
5. operation This Class B digital apparatus complies with Canadian ICES 003 SYSTEM REQUIRMENTS e Windows 98SE ME 2000 XP Vista 7 e Pentium 233 MHz or higher e At least 64 MB RAM e Available USB port e Mac OS 9 or later for USB 1 1 mode e Mac OS X or later for USB 2 0 mode WARNINGS Your hub automatically shuts off any port with a low or excessive current If USB Hub Current Limit Exceeded appears on your screen disconnect the affected USB device click Reset on the screen and reconnect the device If one of your hub ports is disabled but USB Hub Current Limit Exceeded does not appear e Disconnect and reconnect the affected device e If the port still does not work disconnect the hub and the device and then reconnect Keep your desktop hub dry if it gets wet wipe it dry immediately Do not modify or tamper with your desktop hub s internal components It may cause a malfunction and invalidate its warranty Modifications not approved by the party responsible for compliance could void user s authority to operate the equipment Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 3 Factory 16015 Model SPCA GDH Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly A Desk Top 1 B Left Pedestal Left Panel 1 C Left Pedestal Right Panel 1
6. 4 into the inner end holes of the Sliding Shelf O Tap in with a rubber mallet if necessary Make sure that you use a small amount of glue with both ends of all dowels NOTE It is very important to use a small amount of glue on both ends of dowels 21 Align the drilled holes on the Sliding Shelf Front Molding O1 with the inserted Wood Dowels 4 on the Sliding Shelf O and then press them together Secure the Sliding Shelf Front Molding O1 in place by engaging three Large Cam Locks 2 As shown 22 Repeat last two steps to attach the Pull out Tray Front Molding N1 to the Pull out Tray N Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 12 Factory 16015 Model SPCA GDH Assembly Instructions 23 Pick up 14 Left and Right Sliding Shelf Slides YL and YR and separate the Slide Runners for the following step Extend the Slide Runner all the way forward Press the plastic release lever of the slides up and pull the Slide Runner complete out 24 With the pilot holes as a guide attach the separated Left and Right Slide Runners YL and YR to the bottom of Sliding Shelf O using four 1 2 Black Screws 6 through the metal tabs and screw into the pilot holes Ensure the closed end of the slides points towards the sliding shelf front molding Slide opening 25 Apply the same technique to attach the 12 Pull out Tray Slides XL and XR to the Pull out Tray
7. PCA GDH Desk Top Modesty Panel Left Pedestal Left Panel Left Pedestal Right Panel Left Pedestal Bottom Panel Left Pedestal Bottom Stretcher Left Pedestal Middle Crossbar Left Pedestal Back Panel Desk Door Panel Desk Adjustable Shelf Right Pedestal Left Panel Right Pedestal Right Panel Right Pedestal Bottom Panel Right Pedestal Bottom Stretcher Right Pedestal Middle Crossbar Right Pedestal Back Panel Pull out Tray Pull out Tray Molding Sliding Shelf Sliding Shelf Molding Utility Drawer Front Utility Drawer Back Panel Utility Drawer Left Side Utility Drawer Right Side Utility Drawer Bottom Panel File Drawer Front File Drawer Back Panel SPCA GDH 28 FDLS SPCA GDH 29 FDRS SPCA GDH 30 FDBP SPCA GDH 31 GR SPCA GDH 32 FH SPCA GDH 33 GB SPCA GDH 34 12PTLS SPCA GDH 35 12PTRS SPCA GDH 36 14SSLS SPCA GDH 37 14SSRS SPCA GDH 38 16BBS SPCA GDH 39 LST SPCA GDH 40 RST SPCA GDH 41 LSR SPCA GDH 42 RSR SPCA GDH 43 HTP SPCA GDH 44 HLOP SPCA GDH 45 HROP SPCA GDH 46 HBS SPCA GDH 47 HLIP SPCA GDH 48 HRIP SPCA GDH 49 HLPP SPCA GDH 50 HRPP SPCA GDH 51 HSFS SPCA GDH 52 HLFS SPCA GDH 53 HMFS hume gg Suan oN File Drawer Left Side File Drawer Right Side File Drawer Bottom Panel Guide Rail File Hanger Guide Block 12 Pull out Tray Left Slides 12 Pull out Tray Right Slides 14 Sliding Shelf Left Slides 14 Sliding Shelf Right Slides 16 Ball Bearing Slides Left Slide
8. Track Right Slide Track Left Slide Runner Right Slide Runner Hutch Top Panel Hutch Left Outer Panel Hutch Right Outer Panel Hutch Bottom Stretcher Hutch Left Inner Panel Hutch Right Inner Panel Hutch Left Partition Panel Hutch Right Partition Panel Hutch Small Fixed Shelf Hutch Large Fixed Shelf Hutch Medium Fixed Shelf SPCA GDH 54 HDP SPCA GDH 55 HAS SPCA GDH 56 HLBP SPCA GDH 57 HRBP SPCA GDH 58 HMBP SPCA GDH 59 SCL SPCA GDH 60 LCL SPCA GDH 61 CB SPCA GDH 62 M8x30WD SPCA GDH 63 1 2ZS SPCA GDH 64 1 2BS SPCA GDH 65 1 1 4S SPCA GDH 66 1 1 2S SPCA GDH 67 3 4 RSN SPCA GDH 68 5 8S SPCA GDH 69 SP SPCA GDH 70 CLC SPCA GDH 71 USBH SPCA GDH 72 H SPCA GDH 73 HB SPCA GDH 74 DH SPCA GDH 75 MB SPCA GDH 76 G SPCA GDH 77 TUP SPCA GDH 78 TRHK SPCA GDH CHH SPCA GDH CHD Hutch Door Panel Hutch Adjustable Shelf Hutch Left Back Panel Hutch Right Back Panel Hutch Middle Back Panel Small Cam Lock Large Cam Lock Cam Bolt M8 x30 mm Wood Dowel 6 x 1 2 Zinc Screw 6 x 1 2 Black Screw 8 x 1 1 4 Screw 8 x 1 1 2 Screw 3 4 Ring Shank Nail 6 x 5 8 Screw Shelf Pin Cam Lock Cover USB Hub Handle Handle Bolt Door Hinge Metal Bracket Glue Touch up Pen Tipping Restraint Hardware Kit Complete Hardware for Hutch Complete Hardware for Desk
9. WHALEN sits DATE PURCHASED Greenwich Computer Desk Desk Model SPCA GDH ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS SHARP POINTS SHARP EDGES AS RECEIVED 2 PEOPLE RECOMMENDED If you have any questions regarding assembly or if parts are missing DO NOT return this item to the store where it was purchased Please call our toll free customer service number and have your instructions and parts list ready to provide the model name part name or factory number 1 866 942 5362 Pacific Standard Time 8 30 a m 4 30 p m Monday Friday Or visit our web site 24 hours a day 7 days a week for product assistance at www whalenfurniture com Or e mail your request to parts whalenfurniture com THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION PLEASE READ AND KEEP FOR FUTURE REFERENCE Whalen Furniture Mfg Inc Page 1 Factory 16015 Model SPCA BWC Important Before you begin Open identify and count all parts prior to assembly Lay out parts on a flat and non abrasive surface You will need the parts identified on page 4 5 and 6 of this instruction manual NOTE IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH Insert Dowel at least half way by tapping lightly with a rubber mallet IF NECESSARY CAM LOCK SYSTEM OPERATION HOW THE KNOCK DOWN KD ASSEMBLY SYSTEM WORKS 1 Screw the Cam Bolt into the threaded inserts on the pane
10. computer that has a version 1 1 USB interface all of the devices attached to the hub will run at USB 1 1 speed NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired
11. hat will not scratch the surface when dusting Use of furniture polish is not necessary Should you choose to use polish test first in an inconspicuous area Using solvents of any kind on your furniture may damage your furniture s finish Never use water to clean your furniture as it may cause damage to the finish Always use coasters under beverage glasses and flowerpots Liquid spills should be removed immediately Using a soft clean cloth blot the spill gently Avoid rubbing Always use protective pads under hot dishes and plates Heat can cause chemical changes that may create spotting within the furniture finish Stains or marks from crayons or ink markers will be difficult to remove In the event that your furniture is stained or otherwise damaged during use we recommend that you call a professional to repair your furniture Check bolts screws periodically and tighten them if necessary Further advice about wood furniture care It is best to keep your furniture in a climate controlled environment Extreme temperature and humidity changes can cause fading warping shrinking and splitting of wood It is advised to keep furniture away from direct sunlight as sun may damage the finish Proper care and cleaning at home will extend the life of your purchase Following these important and helpful tips will enhance your furniture as it ages A Touch up Pen has been provided to repair any small nicks or scratches that may occur during asse
12. l Connect both panels together making sure Cam Bolt goes into the pre drilled hole on the end of panel for Cam Lock 2 Insert the Cam Lock into the pre drilled large hole on the panel Make sure the arrow on the face of Cam Lock faces out and points towards Cam Bolt 3 Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place 4 Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam You are now ready to assemble the KD unit Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 2 Factory 16015 Model SPCA BWC 4 Port USB Desktop Hub User Guide Please read this user guide before installing and using your integrated desktop hub INTRODUCTION The integrated 4 Port USB 2 0 Desktop Hub offers 480 Mbps high transmission rate and can connect up to three devices such as a digital camera MP3 player cell phone or wireless mouse With plug and play capability you can add a device without restarting your computer INSTALLATION The hub installs automatically If necessary follow the onscreen instructions to complete installation Once the default drivers are installed the red LED status indicator light will glow and you can connect devices to the hub NOTES e To reach USB 2 0 high speed your computer or host adapter card must support USB 2 0 This hub is also backwards compatible with USB 1 1 e When using the hub with a
13. ll face up Unfinished gt gt surface T4 T3 T2 Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 10 Factory 16015 Model SPCA GDH File Drawer Assembling 15 Fasten the File Drawer Back Panel T1 to File Drawer Side Panels T2 and T3 using four 1 1 4 Wood Screws 7 Make sure that Drawer Bottom Panel T4 fits securely into the groove of the Drawer Back Panel T1 Tighten all the screws with a Phillips screwdriver Ti QA P N ag P 7 T4 l T4 T2 T2 16 Turn the assembled drawer upright Fit the Guide Rails U onto the File Drawer Side Panels T2 and T3 with the high side facing inward 17 Hook 2 Guide Blocks W onto the high edge of each Guide Rail U Now set the File Hanger V into the slot of each pair Guide Blocks W Slide the File Plates forward and backward to keep hanging files organized 18 Attach a Drawer Handle 12 to the outside of the File Drawer Front T using two Handle Bolts 13 Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 11 Factory 16015 Model SPCA GDH Assembly Instructions 19 Locate the Pull out Tray Molding N1 and the Sliding Shelf Molding O1 and securely screw the Cam Bolts 3 into the designated small holes as shown in the illustration oO WERO ge ae U G HR amp O1 N1 20 Insert two Wood Dowels
14. mbly or shipping We hope you enjoy your purchase for many years Thank you for your purchase QUALITY GUARANTEE We are confident that you will be delighted with your Whalen Furniture purchase Should this product be defective in workmanship or materials or fail under normal use we will repair or replace it for up to one 1 year from date of purchase Every Whalen Furniture product is designed to meet your highest expectations We guarantee that you will immediately see the value of our fine furniture This warranty gives you specific legal rights and you may also have other rights which vary from province to province state to state Customer Service 1 866 942 5362 8 30 a m 4 30 p m PST Monday to Friday www whalenfurniture com Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 21 Factory 16015 SPCA GDH 1 DT SPCA GDH 2 MP SPCA GDH 3 LPLP SPCA GDH 4 LPRP SPCA GDH 5 LPBP SPCA GDH 6 LPBS SPCA GDH 7 LPMC SPCA GDH 8 LPBP SPCA GDH 9 DDP SPCA GDH 10 DAS SPCA GDH 11 RPLP SPCA GDH 12 RPRP SPCA GDH 13 RPBP SPCA GDH 14 RPBS SPCA GDH 15 RPMC SPCA GDH 16 RPBP SPCA GDH 17 PT SPCA GDH 18 PTM SPCA GDH 19 SS SPCA GDH 20 SSM SPCA GDH 21 UDF SPCA GDH 22 UDBP SPCA GDH 23 UDLS SPCA GDH 24 UDRS SPCA GDH 25 UDBP SPCA GDH 26 FDF SPCA GDH 27 FDBP IF YOU NEED TO ORDER ANY REPLACEMENT PARTS PLEASE USE THE LIST BELOW Greenwich Computer Desk with Hutch S
15. nd Hardware List Please read completely through the instructions and verify that all parts listed are present before beginning assembly YR 14 Sliding Shelf Right Slides 1 Z 16 Ball Bearing Slides 2 CL Left Slide Track 1 a i DL Left Slide Runner 1 DR Right Slide Runner 1 D 1 Small Cam Lock 2 Large Cam Lock 3 Cam Bolt 4 M8 x30 mm Wood Dowel 8 1 extra 42 2 extra 50 2 extra 46 2 extra unnm 5 6 x 1 2 Zinc Screw 6 6 x 1 2 Black Screw 7 8 x 1 1 4 Screw 8 3 4 Ring Shank Nail 8 1 extra 44 2 extra 8 1 extra 34 1 extra 9 Shelf Pin 10 Cam Lock Cover 11 4 Port USB Hub 12 Handle 4 1 extra 4 1 extra 1 3 LS 13 Handle Bolt 6 1 extra 14 Door Hinge 2 sets Glue 1 Tools required Phillips screwdriver not provided Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 6 Factory 16015 Model SPCA GDH Utility Drawer Assembling Unpack the unit and confirm that you have all the hardware and required parts Assembly the unit on a 1 carpeted floor or the empty carton to avoid any scratch 2 Securely screw 4 Cam Bolts 3 into the designated small holes on the Utility Drawer Front S as shown in the illustration 3 Attach the Utility Drawer Side Panels S2 and S3 to the Drawer Front S by engaging four Small Cam Locks 1 Refer to page 2 on Cam Lock system operation supplement Make
16. r the top hole 5 eT Finished edge Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 19 Factory 16015 Model SPCA GDH Assembly Instructions 52 Plug the Cam Lock Covers 10 onto the visible Cams Locks o to conceal the Cam Locks 53 Extend the 16 Ball Bearing Slide Tracks on the pedestal side panels all the way forward including ball bearing cart Align the Slide Runners on the File Drawer with the Slide Tracks and push the drawer carefully inside until it stops NOTE If the drawer does not go in smoothly please take it out and repeat the step If you need to remove the drawer please pull the drawer all the way out then simultaneously push the plastic release lever of the ball bearing slides up on one side and down on the other side and then pull it completely out 54 Repeat the same procedure to install the Pull out Tray N and Sliding Shelf O in the frame 55 To insert the assembled utility drawers into place tip the front of drawer down and drop the rollers of the drawer Slide Runners behind the rollers of Slide Tracks on the unit Lift the front of the drawer up and slide it into the unit Ball bearing cart Ball bearing cart Drawer Installation Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 20 Factory 16015 Model SPCA GDH Care and Maintenance Use a soft clean cloth t
17. s K to the Right Pedestal Bottom Panel J using two Wood Dowels 4 and one Large Cam Lock 2 in each Make sure that the Cam Locks face inward Cam Locks faces inward ao we 37 Pick up last assembly and attach it to the Right Pedestal Right Panel I using four Wood Dowels 4 and four Large Cam Locks 2 Make sure that the finished edge on the Right Pedestal Bottom Panel J will face the front of the unit As shown 38 Align and attach Right Pedestal Middle Crossbar L to the Right Pedestal Right Panel I using one Wood Dowel 4 and one Large Cam Lock 2 Ensure the Cam Locks point towards the bottom of the unit 39 Repeat last two steps to attach the Right Pedestal Left Panel H at the other end The finished edge facing forward when the desk is turned upright Cam Locks will face the bottom of unit A S P A p p yl H a d KA 4 a 2 l pA Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 16 Factory 16015 Model SPCA GDH Assembly Instructions 40 Attach the separated 12 Slide Tracks XL and XR to the Left Pedestal Right Panel C and the Right Pedestal Left Panel H respectively with three 1 2 Black Screws 6 per slide track Ensure the slide opening points towards the front of the unit 41 Securely screw the Cam Bolts 3 into the designated small holes on the Left Pedestal Right Panel C and the Right Pede
18. ssembled drawer upright 9 Attach one Handle 12 to the outside of the Drawer Front S using two provided Handle Bolts 13 10 Pick up the 16 Ball Bearing Slides Z and separate the Slide Runners for the following step Extend the Slide Runner all the way forward Press the plastic release lever of the ball bearing slides up and pull the Slide Runner complete out 11 Attach the separated Slide Runners Z to the File Drawer Left and Right Side Panels T2 and T3 respectively with three 1 2 Black Screws 6 per slide runner Make sure that the closed end of the Slide Runner against the front edge of drawer side panel Mounting holes Fd SF SS t t t Slide opening Slide opening Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 9 Factory 16015 Model SPCA GDH File Drawer Assembling 12 Securely screw 4 Cam Bolts 3 into the designated small holes on the File Drawer Front T as shown 13 Attach File Drawer Side Panels T2 and T3 to the File Drawer Front T by engaging four Small Cam Locks 1 Make sure that the grooves face inward and line up with each other Grooves line up with each other and face inward Slide opening T2 taro V Legato 14 Slide the File Drawer Bottom Panel T4 into the grooves between the Drawer Side Panels T2 and T3 until fully inserted into the File Drawer Front T Make sure the finished surface wi
19. stal Left Panel E as shown in the illustration XL XR g t Mounting holes l Slide opening Slide opening 42 Attach the Modesty Panel P between the assembled Left and Right Pedestals using four Wood Dowels 4 and four Large Cam Locks 2 As shown Make sure that the Cam Locks point backwards and the cut out of the Modesty Panel is up Cam Locks point toward back of unit Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 17 Factory 16015 Model SPCA GDH Assembly Instructions 43 Insert ten Wood Dowels 4 into the top inner holes of the assembled unit DO NOT put dowels into the Cam Bolt holes Position the Desk Top A onto the inserted Wood Dowels 4 and attach it in place by engaging ten Large Cam Locks 2 44 Now go back and tighten all Cam Locks and Screws Make sure that all the parts are tight and there are no gaps between the pieces This will help keep the unit square 45 Align and attach the Pedestal Back Panels G and M onto the assembled unit with the stained surface facing backward As shown Make sure that the overlaps on the panels are even all the way around Gently hammer the 3 4 Ring Shank Nails 8 through the pre drilled holes on the Back Panels NOTE We recommend attaching the back panels with the Ring Shank Nails at the corners first re Se The notch for metal bracket A 7 ra a Tal Per GIMS
20. sure that the grooves face inward and line up with each other Grooves line up with each other and face inward 4 Slide the Utility Drawer Bottom Panel S4 into the grooves between the Drawer Side Panels S2 and S3 until fully inserted into the Drawer Front S Make sure the finished surface will face up Unfinished surface S4 3 N s2 S Please call for replacement parts or assistance 1 866 942 5362 Page 7 Factory 16015 Whalen Furniture Mfg Inc Model SPCA GDH Utility Drawer Assembling 5 Fasten the Utility Drawer Back Panel S1 to Drawer Side Panels S2 and S3 using four 1 1 4 Wood Screws 7 Make sure that the Drawer Bottom Panel S4 fits securely into the groove of the Drawer Back Panel S1 Tighten all the screws with a Phillips screwdriver S1 te S3 a Bs a s n tees 6 Using the pilot holes as a guide align and attach the Left Slide Runner DL to the Drawer Left Side Panel S2 using three 1 2 Black Screws 6 Make sure that the roller end of Slide Runner faces backward Tightly fasten with a Phillips screwdriver 7 Repeat last step to attach the Right Slide Runner DR to the Drawer Right Side Panel S3 DLIDR Mounting holes D lt i P Roller end S2 l keg 6 Mago edge faces upward 6 Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 8 Factory 16015 Model SPCA GDH Assembly Instructions 8 Turn the a
Download Pdf Manuals
Related Search