OCTOPUSTRI - Industry Gear
Contents
1. WWW LIGHTEMOTION COM AU OCTOPUSTRI DMX LED Tri Mover 1 X 9W Tri Led RGB in 1 User s instruction manual This manual contains important information about the safe installation and use of this product Please read this instruction manual carefully before installing or operating Please keep these instructions in a safe place for future reference www lightemotion com au 1 of 6 pages Congratulations on the purchase of your OCTOPUSTRI by Light Emotion We are confident that you will be satisfied with your purchase We have prepared this manual to assist you with the operation of this item This is the newest series of DMX LED EFFECT LIGHT containing 1 x 9W Tri LED It can run with the digital display for built in programs sound active mode with sensitivity control master slave mode and DMX mode OCTOPUSTRI s applications include use in clubs bars and home parties This ultra strong beam effect is best when used in conjunction with a fog machine CONTENTS SECTION Page WHAT IS INCLUDED SAFETY INSTRUCIONTS 2 INSTALLATION MAINTENANCE 3 POWER FUSE DMX LEAD DMX TERMINATOR 4 OPERATION SPECIFICATIONS Please note that as part of out ongoing commitment to continuous improvement and product development the specifications in this manual are subject to change without notice Whilst every care has been taken in the preparation of this manual we reserve the right to change specifications in the course of product impr2. serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Never connect the device to a dimmer pack e Make sure power cord is never crimped or damaged e Never disconnect power cord by pulling or tugging on the cord e Avoid direct eye exposure to the light source while it is on INSTALLATION CAUTION For safe mounting read the following instructions carefully e Wire e Use suitable hook clamps for hanging the lighting effect e Use a safety wire with a breaking strain of more than double the lighting effect e Donotlook directly into the light source Boo m e Make sure the lighting effect has suitable ventilation as per the ae instructions below e This lighting effect is intended for indoor use only to avoid electrical shock keep away from rain and moisture e Keep unit out of reach from children NOTE Use washers and spring washers when attaching your hook clamp to the yoke 1 For installation of the hook clamps and safety wire 2 This lighting effect must be 0 5m away from any flammable materials or any walls or ceilings 3 Do not block or inhibit the air flow from the ventilation vents Light Emotion has various hook clamps and safety wires suitable for your OCTOPUS
3. O1 to SU99 sensitivity control less sensitive to very sensitive Auto Mode Press the mode button till the display shows AUTO The unit will run slowly and with colour change effect Slave Mode Press the mode button till the display shows SLAU SPECIFICATION e Weight 2kgs e Dimension LxWxH 250 x 177 x 240mm e Power input AC 110 240V 50Hz 60Hz e Fuse F3A 250V e Maximum consumption 30W e LED RGB 3IN1 9Wx1 6 of 6 pages
4. TRI Please contact your local dealer for more information MAINTENANCE amp PERIODIC CHECKS CAUTION Some maintenance and checks may require the product to be opened and should only be done by qualified persons Warranty may be void if damage has been caused by improper maintenance Perspex lenses should be wiped with a clean moist cloth to remove dust and residue 3 of 6 pages POWER CAUTION This lighting effect is designed to operate at 110 240V 50Hz 60Hz Connect the supplied power lead to the lighting effect Power input socket Power Consumption 30W FUSE CAUTION Only use the correct fuse as specified on the rear panel of the lighting effect Disconnect the lighting effect from the mains before attempting to replace the fuse To replace the fuse please follow the following steps 1 Remove the fuse holder cover with a screwdriver 2 Remove existing fuse 3 Fit new fuse 4 Refit the fuse holder Fuse M205 3A fast 250V DMX LEAD The DMX lead is used to link up multiple units SIN ROT OH O DMX TERMINATOR A DMX terminator helps to reduce noise on the DMX chain and makes the light respond to control more accurately It should be plugged in to the last fixture in any chain DMX TERMINATOR CONNECTION Connect a 120 OHM resistor across pins 2 and 3 in an XLR plug and insert into the DMX OUT socket on the last unit in the chain 4 of 6 pages OPERATION NOTE Unit uses a 4
5. button LED control panel The display will switch off after 5 seconds without any operation DMX Mode Press the mode button till the display shows AXXX and then press the set up button to select the address XXX would flash And then push the up or down buttons to select the address from A001 to A512 Then press the set up button to confirm DMX Map CH1 000 007 COLOR 01 008 015 COLOR 02 016 023 COLOR 03 024 031 COLOR 04 032 039 COLOR 05 040 047 COLOR 06 048 055 COLOR 07 056 063 COLOR 08 064 071 COLOR 09 072 079 COLOR 10 080 087 COLOR 11 088 095 COLOR 12 096 103 COLOR 13 104 111 COLOR 14 112 119 COLOR 15 0 9 120 127 COLOR 16 NO 128 135 COLOR 17 ROTATION 136 143 COLOR 18 144 151 COLOR 19 152 159 COLOR 20 160 167 COLOR 21 168 175 COLOR 22 176 183 COLOR 23 184 191 COLOR 24 192 199 COLOR 25 200 207 COLOR 26 208 215 COLOR 27 216 223 COLOR 28 224 231 COLOR 29 232 239 COLOR 30 240 247 COLOR 31 248 255 COLOR 32 10 120 CLOCKWISE FAST SLOW CH2 135 245 121 134 246 255 COUNTER CL NO NO OCKWISE ROTATION ROTATION SLOW FAST 5 of 6 pages CH3 1 255 STROBING SLOW FAST CH4 Sound Active Mode Press the mode button till the display shows SUXX press set up button to set up the sensitivity The XX would flash And press the up or down buttons to adjust the sensitivity and then press the set up button to confirm SUOO no sound and the unit runs automatically SU
6. ovement WHAT IS INCLUDED CAUTION Do not use sharp objects whilst unpacking this product e 1x OCTOPUSTRI e 1x Warranty card e 1x User manual Please note Some of the items above may be fitted to the product by the manufacturer SAFETY INSTRUCTIONS Please read these instructions carefully It includes important information about the installation usage and maintenance of this product e Please keep this User Manual for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet e Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on the rear panel of the fixture e This product is intended for indoor use only To prevent risk of fire or shock do not expose fixture to rain or moisture e Make sure there are no flammable materials close to the unit while operating 2 of 6 pages e The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surface Be sure that no ventilation slots are blocked e Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse source e Secure fixture to fastening device using a safety chain Never carry the fixture solely by its head Use its carrying handles e Maximum ambient temperature is 35 C Do not operate fixture at temperatures higher than this In the event of
Download Pdf Manuals
Related Search