user manual
Contents
1. LASER DISPLAY SYSTEM USER MANUAL BIG DIPPER LASER SCIENCE amp TECHNOLOGY CO LTD REV 1 01 Please read carefully before installing or operating ANIMATION LASER USER MANUAL Model M150G Notices 1 10 11 12 This is 3B laser product Avoid eyes direct exposure to the laser light Operate abide by the user manual Do not disassemble or repair the system by yourself When there is a problem please contact technician or your local dealer Installation should be done by professional technician Please set the laser product far away from those things as strobe light Do not exposure the system to wet environment Do not touch the system by wet hand and pull the power cable forcefully The work temperature is 10 40 Cso the laser conduct doesn t work until it reach the work temperature when taking it in from cold environment Do not turn on or off the system frequently avoid turning on it for long time Prevent from strong vibration or G shock to the system Prevent other harmful objects from entering the system Keep at least 1 meter between the system and the objects in the lighting Connect the power cable after the system has been installed 13 Turn on the computer after the laser display system is on Page 1 or you must power on the computer again 14 Before powering on the system be sure the power cable is connected into the power socket well 15 Turn off the system for 25 minutes after ru2. exhaust is not blocked 4 The LASER display system should be statically fixed 5 It is essential to be earthed well for the sake of saf y Back panel DMX ADDRESS Key press function instruction fan Binary address switch Binary address switch control the patterns change IN DMX512 signal input OUT DMX512 signal output F3AL 250V Input power with internal fuse 3A Page 3 Technical Parameters Model M150G Parameters 1 LASER diode Green 2 Power supply 100 240VAC 50 60Hz 3 LASER power G gt 100mW 532nm Scanner angle 30 5 Control mode Sound auto play single pattern by DMX control D Running under the mode of DMX Audio 6 Peculiarity and AUTO Capable show animation patterns by the following motion blanking zoom horizontal 7 Effect vertical or graphic s movement along the twa direction by in phase or asynctronous offset rotate wave dotline mode strobe 8 Dimensions 236 218 137 3 mm Net weight a Gross weight aaae page 4 DMX channel setting Channel No UMXSLA Content value 0 51 Shut off the LASER diode 1 Control 52 103 Sound control mode mode 104 155 AUTO mode 156 210 Auto Animation Mode 211 255 Manual mode 0 99 Static pattern 100 101 Letters 2 Pattern 102 103 Animal patterns 104 105 Guitar animati
3. mers Page 7 0 No rotate g Rotation 1 180 Manual Rotate 181217 Clockwise rotate automatic 218 255 Anti clockwise rotate automatic 0 69 Normal display 10 Display 70 139 Dot and line display mode 140 209 Subsection display 210 255 Dot Display 0 10 No wave Wave frequency from low to high 11 70 in horizontal direction Frequency and fixed extent from 11 Wave 71 130 low to high in horizontal direction Wave frequency from low to high 131 190 in vertical direction Frequency and fixed extent from 191 255 low to high in vertical direction 0 1 No gradually draw 12 Gradually 2 149 Manual gradually draw draw 150 255 Gradually draw circularly with10 grade speed Remark The effect from channel 3 to channel 12 as described can take effect only under the conditions that the graphics in the channel 2 and the DMX channel from 0 to 99 Remark On the DMX 512 mode the LASER display system will shut off if the DMX 512 signal intermit ADDRESS DMX address setup 1 When the 10th code is ON the function of 1 9 codes is the following The ist code is off seund control mode host laser The 1st code is on Auto play mode host laser The 1st and 3rd code is on automatic animation host Laser 2 When the 10th code is off DMX control Page 6 2 Be sure the power socket output voltage matches that off the LASER display system Ensure the fan and the
4. nning constantly for three hours ensure that the system is able to cool down in a suitable environment 16 When to be transported use the original package to avoid damage 17 This sign indicates separate collection for electronics and electrical equipment Inspection Check that the following components are present within the package when receiving system from the list below 1 x LASER display system 1 x User manual 1 x Power cable 1 x DMX cable optional Installation 1 Be sure that there is no flammable or explosive subjects nearby The least clear proximity from the system should be 1 5 meters At the same time keep more than half a meter between the wall and LASER display system Page 2 Maintenance Clean the lens regularly Do not use a wet cloth or chemicals use a damp cloth The maintenance period depends of the usage frequency and surrounding conditions of the LASER display system It recommended that the system should be cleaned every 15days Warning Power off any related system before maintenance Declare The end user of this product should abide by the above instructions and warnings Performing actions which was advised not to do so as stated by this manual may void the warranty of this laser display system All products made from Big Dipper Laser Company have anti fake identification please verify the anti counterfeit label at the bottom of the case to ensure the interests of consu
5. on 106 255 Dynamic patterns 0 30 No strobe 3 Stobe 31 255 Strobe 0 167 Manual move Automatic move circularly from right to 4 Horizontal 168 188 left move Automatic move circularly from left to 189 209 right 210 255 Automatic move around circularly 0 167 Manual move Automatic move circularly from down 168 188 to up Vertical 5 MOVE Automatic move circularly from up to 189 209 down Automatic fluctuate circularly from up 210 255 to down and down to up 0 10 Original size 11 104 Manual zoom 6 Zoom 105 154 Automatic zoom out circularly 155 204 Automatic zoom in circularly 205 255 Automatic zoom circularly 0 No stretch 7 Lee 1 150 Manual stretch stretch z 151 255 Automatic stretch 0 No stretch 8 ies 1 150 Manual stretch 151 255 Automatic stretch page 5
Download Pdf Manuals
Related Search