VEHICLE ALARM SYSTEM `GN7`
Contents
1. ON OFF generates single 0 8 second pulse SN 10 Central lock is controlled by single 15 second pulse on arming and 0 8 second pulse on disarming turning ignition ON OFF generates single 0 8 second pulse SN 11 Central lock is controlled by single 40 second pulse on arming and 0 8 second pulse on disarming turning ignition ON OFF generates single 0 8 second pulse SN 12 Central lock is controlled by computer pre programmed two pulse sequence FN 56 Feature ACTION OF THE CENTRAL LOCK ON IGNITION ON WHEN THE DOORS ARE OPEN SN 1 The central lock is locked even when not all the doors are closed SN 2 The central lock is locked only when all the doors are closed FN 57 Feature ACTION OF THE CENTRAL LOCK ON TURNING THE IGNITION OFF On turning the ignition ON the central lock is locked on turning the ignition OFF the central lock is unlocked SN SN FN S8 SNTI SN FN 59 Feature PERIOD OF PULSES OF AUTOMATIC ENGINE START Pressing button when ignition is turned ON period of automatic engine start pulses can be set with 30 minute discretion for automatic engine start feature selected on FN 51 setting standard period is 30 minutes FN 65 Feature TYPE OF SIREN AND ARMING DISARMING CONFIRMATION SIGNAL LEVEL 1 Siren with no inner modulation speaker with coil impedance at least 4 Ohm Maximum sound level N f SE SNS 7 1 Silent Arming and disarming with no siren signal SN SE 4 L2. s siol sis iistol Jel iel te isl Teo telleti lt jet lt sis lt 1 e ile tT Jel kloi lt lel khem zone is triggered FEATURE SN 6 The system generates in optional output the pulse signal intended for pager in case the door engine hood or luggage compartment is opened sensor gt pre alarm zone or sensor alarm zone is triggered The negative polarity pulse is generated in optional output for trunk release gadget control in case the remote control button is pressed for over 2 seconds SN 7 The pulse duration equals to button press duration The system returns to regular armed mode as defined by FN 33 setting after the trunk is closed Automatic engine start pulse The negative polarity pulse is generated in optional output in case the remote control button is pressed over 2 seconds SN 8 The pulse duration equals to button press duration plus 1 5 second The pulse is intended for the automatic engine start module The module is enabled to turn ON the ignition within 8 seconds since the pulse first edge or the ignition is turned OFF The doors engine hood and luggage compartment are protected Periodical automatic engine start pulses The negative polarity pulses are generated in optional output in case the remote control button is pressed over 2 seconds The first pulse duration equals to button press duration plus 1 5 second the duration of other pulses is 1 5 second pulse period is defined by FN 59 setting The pu
3. 6 sch SOL SSS ISOL IS SISS cei ISL ISO pil is pe 2 ee se See Ss So Se JON ASSISTS ISIS RISE TS Ss TR SSL S seis eI 6 ISIS Soi eer es ees Esa SSIS IRIs ts ese cles 9 GN7_C WIRING DIAGRAM 14V DC 25A max Cut off Aj circuit on 4 Ultrasonic sensor External sensor E I V a2zjfi 234567 Aerial Leon A max ka 7 A Contacts of Relay K1 Right direction indicators Left direction indicators Siren without inner modulation FN 65 SN 1 4 5 o D z ral Fel Ee fod fs System LED Ultrasonic sensor D LE BON Hood switch WAVES 9 Switch in the door strut FN 19 SN 1 4 5 ee DOORS l l Switch in i the door strut CNS SN a ae Luggage compartment switch T LUG FN 18 SN 1 GSM aerial FN 18 SN 2 Automatic GSW1 engine start FN 51 SN 11 confirmation OPTIONAL FEATURE O See eee ee l l Cut off es ee eee circuit i FN 51 SN 2 PE ags CEE 12V Secret button Cut off FN 51 SN 1 10 GN7 SETUP BY PC Setup sequence a connect the RF LATCHER to PC USB port b launch CAdmin software c enter installer name and password d enter client data and alarm serial No e setup alarm settings f enter alarm PIN code and wait 13 secods for alarm switching to service mode g press programming button in CAdmin software window h observe short direction indicator flashes on each data packe
4. SING A REMOTE CONTROL SN 1 OFF Arming without using a remote control The system is armed and central lock is locked in case the ignition is turned off the secret button is pressed twice the door is opened and closed Warning don t leave the keys and remote inside vehicle FN 42 Feature WARMING UP THE ENGINE SNE With the ignition ON press a secret button twice get off of the vehicle and press remote control button System will arm and lock central lock The system will not respond to sensors however in case of opening the doors engine hood or trunk the siren will start sounding direction indicators will start flashing and after 10 seconds the system will immobilize engine and rearm setting FN 23 SN 2 or the system will immobilize engine and rearm just after turning the ignition OFF setting FN 23 SN 1 System is disarmed in the usual way i e using remote control FN 44 Feature AUTOMATIC REARMING The system is automatically armed in case vehicle door engine hood and luggage compartment no opening or ignition is not turned ON within 45 seconds after system disarming Central lock is not locked SN 2 Il N T 9 The system is automatically armed in case vehicle door engine hood and luggage compartment no opening or ignition is not turned ON within 145 seconds after system disarming Central lock is locked SN 3 Automatic rearming is OFF The system is automatically armed in case during th
5. T Central lock motor Serta ejja Lock pulses 130mA 12V IGN ap ee 0 Ignition y lock STAR To direction indicators l status input Aerial FN 17 SN 2 gt ib A Right direction indicators TIN Hazard os warning Left direction button AE a Ultrasonic sensor Dan c indicators Contacts of kes K T b d o on boar The direction indicators computer status input S ES FN 17 SN 2 i Siren without inner modulation l FN 65 SN 1 4 Secret button l Additional input x2 1s 2 g FN 17 SN 1 1 __ se a 2 a a 2 l System LED j 5 Electronic siren Ultrasonic sensor gt Jen FN 65 SN 5 3 oe E Bonnet switch 1 1 m Switch in the door strut at DOORS aa FN 19 SN 1 l Switch in the door strut Tr i FN 19 SN 2 byl Ground y o _6 Luggage F 7 Vehicle a Unlock pul compartment switch _ LUG one Sos D Battery FN 18 SN 1 GSM aerial ae FN 18 SN 2 ay py AA Central lock Automatic af la i motor GSW1 engine start Lock pulses FN 51 SN 11 confirmation 130mA OPTIONAL FEATURE A 3A y BY FN 51 SETTING IGN mi ON pok 12V a OS Ignition Cut off E a 4 A lock circuit FN 17 SN 2 Secret button Cut off FN 51 SN 1
6. TION CONDITION ACTION TIME CONTROL ae ATORS SIREN SYSTEM LED Doors is opened PIN ENTRY Double flashes long flashes REMOTE 12 seconds is extended Press simultaneously Triple flashes to 12 seconds after ORLO RAA 1 second flash after PIN is entered CONTROL LEARNING each remote control or remote contiol learning DD is learned 12 seconds after PIN entry or Indicates reme CORI FN ENTRY 8 minutes correct Double flashes FN entry learning FN is entered Short press Indicates SN Indicates SN SN FN hecked a SN CHANGE 8 minutes oe Helge of change after change after Double flashes ignition ON 3 seconds 3 seconds Indicates SN Is a 8 minutes correct Double flashes or entere FN entry Following FN Shar E Indicates SN Indicates SN is entered SN CHANGE 8 minutes of 5 change after change after Double flashes ignition ON 3 seconds 3 seconds END of FN FN 11 ENTRY or 8 mi J short press Indicates correct Double flashes settings by remote control Pte i of FN entry 6 NOTIFICATION ABOUT OPEN SYSTEM INPUTS DATA ABOUT LAST TRIGGERS If system was triggered in armed state direction indicators will flash four times when disarming the system GN7 stores the data about last three triggers This feature enables to ascertain the causes of the false alarm There are two ways to do that 1 Disarm alarm system turn the ignition ON and count the LED flashes last trigger indication 2 Or set FN 71 72 or 73 press button and c
7. VEHICLE ALARM SYSTEM GN7 Installation manual 1 THE SET a system unit with connecting wires b 2remote controls c engine bonnet switch d user and installation manual e siren optional 2 TECHNICAL SPECIFICATIONS v Operating temperature cece cece cece cece esteetssteeee 40 C to 85 C y Tated Supply VONAGE histeria ened a a aa 9 15V DC v average current consumption without inbuilt sensor lt 14mA U 12V v average current consumption with inbuilt sensor lt 20 mA U 12V v siten dive CUTE rice becca oats e aaa Toei Y cute Cercul CUNEN anenee a a lt 25 A v average distance of remote control ccceeeeeeeeeeee SS 0m 3 INSTALLATION OF THE ALARM SYSTEM Vehicle alarm system GN7 is designed for all types of vehicles except cabriolets with petrol or diesel engines and 12V batteries with negative pole connected to ground vehicle body Vehicle alarm system must be installed inside the vehicle passenger compartment in difficult to access area in accordance with manufacturer s supplied wiring directions Manufacturer of the alarm system recommends a select a qualified installer of vehicle alarm systems b mount system unit in place free from penetration of moisture and other corrosion causing materials as far as possible from heating elements in the passenger compartment and sources of electromagnetic interference vehicle compu
8. andard activation time is 40 seconds FN 31 Feature PRE ALARM ZONE OF BUILT IN SHOCK TILT SENSOR ADJUSTMENT Sensitivity of pre alarm zone is increased in steps by pressing button and decreased in steps by pressing button Number of sensitivity values 20 step indication flash of direction indicators adjustment limit indication direction indicators is on for long time FN 32 Feature ALARM ZONE OF BUILT IN SHOCK TILT SENSOR ADJUSTMENT Sensitivity of alarm zone is increased in steps by pressing button and decreased in steps by pressing button Number of sensitivity values 19 step indication flash of direction indicators adjustment limit indication direction indicators is on for long time FN 33 Feature NONE RESPONSE TIME AFTER ARMING SN 1 None response time is 5 seconds The alarm system will not react 5 seconds after arming to door hood luggage compartment and sensors trigger SN 2 None response time is 45 seconds The alarm system will not react 45 seconds after arming to door hood luggage compartment and sensors trigger FN 34 Feature ALARM ZONE OF BUILT IN ULTRASONIC SENSOR ADJUSTMENT Sensitivity of alarm zone is increased in steps by pressing button and decreased in steps by pressing button Number of Sensitivity values 20 step indication flash of direction indicators adjustment limit indication direction indicators is on for long time FN 41 Feature ARMING WITHOUT U
9. ctory setting 8 2 TABLE OF ALARM SYSTEM SETTINGS FEATURE FN 11 Feature END OF FN SETTINGS FN 15 Feature ALARM SYSTEM CONTROL USING GSWI SN 1 Alarm system control using GSWI1 is OFF eal Alarm system control using GSW1 is ON After learning first remote control the system automatically learns the connected GSW1 as a remote control Systemi y g g y y y N SN ignores the commands from not learned GSW1 FN 17 Feature ADDITIONAL INPUT PURPOSE SN 1 Input is used for secret button SN 2 Input is used for direction indicators status test FN 18 Feature INPUT TRUNK PURPOSE SN 1 Input is connected to luggage compartment switch Engine start confirmation When pulse 0 2 V is active in this input GSWI will send SMS message confirming the engine start When pulse is deactivated 2 1 5 12 V SMS message confirming the engine stop will be sent This feature is available if alarm system is equipped with GSWI and special autostart module and feature FN 51 with setting SN 8 or SN 9 is selected FN 19 Feature DOORS TRIGGER POLARITY SNCI Na 22 i Inner immobilizer operated by remote Immobilizer disables the engine after 40 seconds since the ignition is turned off or system is disarmed Immobilization is turned OFF by pressing remote button Immobilizer is turned ON or OFF with ignition ON by pressing remote control buttons and together holding them down till short si
10. e preset time time till 45 seconds is set by opening closing the door action indication short siren signals after disarming the doors are opened and closed till the time is over Central lock is not locked N Z The system is automatically armed in case during the preset time time till 45 seconds is set by opening closing the door action indication short siren signals after disarming the doors are opened and closed till the time is over Central lock is locked FN 51 Feature OPTIONAL CONTROL PURPOSE SN 1 Optional input for the secret button NST ES SN 5 2 Additional immobilization Optional output for control the relay with normally open contacts cutting off the starter operating circuit The pulse for electromechanical gadget for engine release The negative polarity pulse is generated in the optional output by pressing button for over 2 seconds Duration of pulse equals to the button pressing time N Z 3 SN 4 The 40 second negative polarity pulse is generated for power windows raising and or power sunroof closing in optional output on system is arming SN 5 The system generates in optional output the pulse signal intended for pager in case the door engine hood or luggage compartment is opened sensor alarm Ren A e E E ieee ee ee ee ERR ESRI ESERIES Re Sees eRe Ete Eee SES e SESS REA EEASEN Es EseS Sess ee bs Ol Se Foleo eet ee Sete Se es a ee Shs 9 Si ese Sere sie
11. et button and afterwards pressing remote control buttons and together and holding them down till short siren beep SN 6 Anti carjack activated upon ignition turn ON 40 second countdown begins and system follows anti carjack operation setting FN 23 Anti carjack operation or engine immobilization can be cancelled only by pressing the secret button Anti carjack feature can be turned OFF ON with ignition ON by pressing the secret button and afterwards pressing remote control buttons and together and holding them down till short siren beep FN 23 Feature OPERATION OF ANTI CARJACK SN 1 When 40 second countdown ends the system starts the siren direction indicators start flashing After ignition is turned OFF the engine is immobilized and the system rearms If system is armed cancel of engine immobilization is possible only by disarming the system and pressing the secret button SN 7 SN When 40 second countdown ends the system starts the siren direction indicators start flashing After 10 seconds the engine is immobilized and the system Trearms If system is armed cancel of engine immobilization is possible only by disarming the system and pressing the secret button FN 24 Feature TURNING ON TIME OF THE ADDITIONAL PROTECTION Pressing button when ignition is turned ON activation countdown time can be set with 5 second discretion for additional protection feature selected on FN 22 setting st
12. lses are intended for the automatic engine start module The module is enabled to turn the ignition ON within 8 seconds since the pulse first edge or the ignition is turned OFF The doors engine hood and luggage compartment are protected Sen SNc i Na SNc Double pulse Central lock is controlled by two 0 8 second pulses with 0 8 second pause on arming and disarming turning ignition ON OFF generates single 0 8 second pulse SN N f n u Z SN 5 SN 6 Double pulse to lock single pulse to unlock Central is controlled by two 0 8 second pulses with 0 8 second intermission on arming and by 0 8 second pulse on disarming turning ignition ON OFF generates single 0 8 second pulse SN 7 Single pulse to lock double pulse to unlock Central lock is cntrolled by 0 8 second pulse on arming and by two 0 8 second pulses with 0 8 second intermission Jon disarming turning ignition ON OFF generates single 0 8 second pulse Double pulse to lock double pulse to unlock Central lock is controlled by 0 8 and 15 second pulses with 0 8 second intermission on arming and by two SN 8 0 8 second pulses with 0 8 second intermission on disarming turning ignition ON OFF generates single 0 8 second pulse Double pulse to lock double pulse to unlock Central lock is controlled by 0 8 and 40 second pulses with 0 8 second intermission on arming and by two SN 9 0 8 second pulses with 0 8 second intermission on disarming turning ignition
13. nsor in mode Ron Y ksa FNe78 SENSOR SIONAL TYPE Niel Brection tcsters and siren Nie Ceecton retestors srd siren on triggering of the irer zore of the sentor Ni 3 Ceecton raicators Peta FACTORY SETTINGS Niet Restoring foctory settings and the defot FN oode Dy RF LATOHER v2 01 M Aden erenn Ua oC eae Oo a P atomo pe EL axonas O amna EN Cy Monon C DO 420 Fig 2 CAdmin software window 11 GN7_A WIRING DIAGRAM 14V DC 25A max Cut off A 7 circuit 4 ONS Ultrasonic sensor Dm E Secret button G Additional input E al System LED Ultrasonic sensor Dan Es 3E BON Bonnet switch ST Switch in the door strut ft z DOORS NF 19 SN 1 l l Switch in i the door strut ir NF 19 SN 2 De ee ee ee 12V Luggage A compartment switch T e NF 18 SN 1 NF 18 SN 2 Automatic GSWI1 engine start confirmation NF 51 SN 11 OPTIONAL FEATURE BY FN 51 SETTING Cut off _ Fn 130MA LL circuit NF 51 SN 2 Secret button NF 51 SN 1 Cutt off 12 GN7 _L WIRING DIAGRAM 14V DC Al Oo 25A max Cut off circuit a Aerial Tai 7 A Right direction indicators L7 A Left direction indicators Contacts of Relay K1 Siren without inner modulation FN 65 SN 1 4 Electronic siren NF 65 SN 5 12V for direction indicators Ground J A Vehicle Unlock pulses k A batte 130mA
14. oud silent Action as NN 2 but if the alarm system has alarmed in armed state disarming with the sound 4 sound beeps are generated N f Nn Z N Z dh Silent loud Action as NN 3 but if the alarm system has alarmed in armed state disarming with the sound 4 sound beeps are generated FN 67 Feature WARNING MELODY ON SENSOR PRE ALARM ZONE TRIGGER SN 1 Melody 1 using the siren without internal modulation SN 2 Melody 2 using the siren without internal modulation 3 r TI SN 3 Melody 3 using the siren without internal modulation SN 4 Melody 4 using the siren without internal modulation Feature INFORMATION ABOUT THE CAUSES OF THREE LAST TRIGGERS FN 72 The system informs about the causes of three last triggers after entering FN 71 FN 72 or FN 73 and pressing remote button with ignition OFF by FN 73 direction indicators flashes FN 71 last trigger cause FN 72 last but one trigger cause FN 73 last but two trigger cause FN 75 Feature ULTRASONIC SENSOR FN 76 KSD sensor in shock and tilt mode KSD sensor only in shock mode KSD sensor is turned OFF Direction indicators and siren on triggering any sensor zone Direction indicators on triggering sensor pre alarm zone Direction indicators and siren on triggering sensor alarm zone SNc ERE EE TEE E EE E eee E E E A aS see eee EE SEEE EE E e E EE a Er ee ee e eR oe e a aa e a Ea NECARE 8 oss S19 3 5
15. ount flashes of direction indicators while ignition is OFF Meaning of system LED direction indicators flashes 1 flash sensor sensors have been triggered 2 flashes doors have been opened 3 flashes bonnet has been opened 4 flashes trunk luggage compartment has been opened 5 flashes attempts to start ignition key hot wire 7 CERTIFICATE OF INSTALLATION I undersigned qualified installer Certify that installation of Name Surname the below described vehicle alarm system has been carried out by myself pursuant to installation manual supplied by the manufacturer of the system Vehicle description Manufacturer and model Serial number __ OO Registration number Description of vehicle alarm system Type GN7 Model __ Official approval number 97RA 0104829 Installation date Installing company Installer Position signature After installation of the alarm system installer must fill in CERTIFICATE OF INSTALLATION It 1s recommended to mark selected settings in the TABLE OF ALARM SYSTEM SETTINGS underline SN 8 SUMMARY OF ALARM SYSTEM SETTINGS 8 1 MARKED FIELD MEANS EU the setting complies with requirements of EU Directives Selection of settings not complying with EU requirements is permissible if vehicle is operated in non EU state GN7 C the setting is in appropriate software version amp factory setting pre programmed setting if differs from fa
16. ren beep UN at es z N f N ft N Inner immobilizer operated by secret button Immobilizer disables the engine after 40 seconds since the ignition is turned off or at once system is disarmed Immobilization is turned OFF by pressing secret button Immobilizer is turned ON or OFF with ignition ON by pressing the secret button and afterwards pressing remote control buttons and together holding them down till short siren beep SN 3 Anti carjack activated upon ignition turn ON or door opening with ignition ON 40 second countdown begins and system follows anti carjack operation setting FN 23 Anti carjack operation or engine immobilization can be cancelled only by pressing the secret button Anti carjack feature cannot be turned OFF using remote control SN 4 SN 5 Anti carjack activated upon ignition turn ON 40 second countdown begins and system follows anti carjack operation setting FN 23 Anti carjack ope ration or engine immobilization can be cancelled only by pressing the secret button Anti carjack feature cannot be turned OFF using remote control Anti carjack activated upon ignition turn ON or door opening with ignition ON 40 second countdown begins and system follows anti carjack operation setting FN 23 Anti carjack operation or engine immobilization can be cancelled only by pressing the secret button Anti carjack feature can be turned OFF ON with ignition ON by pressing the secr
17. rts flashing frequently d within 8 minutes after the PIN code entry in the same way as PIN enter the FN number of the feature you want to set Short flash of direction indicators indicates correct FN entry No flash of direction indicators means either incorrect FN entry or assigned 8 minutes elapsed e if FN code has not been entered due to elapsed time press button enter PIN code wait 12 seconds and enter FN once again f if FN code has not been entered due an error turn off the ignition wait until system LED starts flashing frequently and re enter the FN code After correct entry of the FN code the system extends control time for 8 minutes awaiting a remote control button press Within this control time check current SN settings or enter a new one The system extends control time to 8 minutes again This control time is extending every time after checking or entering SN g check SN setting only with the ignition OFF by pressing remote control button once and counting short flashes of direction indicators which equal to SN value h if SN is incorrect to change it turn the ignition ON press button with l second intervals as many times as the required number of SN Wait for 3 seconds till short siren beep and flash of direction indicators New setting has been entered into memory therefore turn the ignition OFF and check SN setting as described in article 4g 5 SUMMARY OF ALARM SYSTEM SETTING SEQUENCE CONTROL REMOTE RREC
18. t is sent and long irection indicator flash on all data is sent successfully Fig 1 Equipment for alarm setup by PC Note latest CAdmin software version is available for download on web site http www kodinis lt en products ACC 2 z Electronic siren 12V for system 5 12V for direction indicators Ground Ld ST ae Vehicle Unlock pulses battery 130mA Central lock Lock pulses ie motor 130mA 3A 12V IGN CJ yf oN n O A ni Ignition ACC lock START E y raros settings dg Sove veto e gt eco a a OSC GEA 5 Ext Usa terrgiste E Sre tensie k Prt Bi eeno A katsirr R Appication optorz MET TES Trg e tren Wihod rier oar Nies Madexty 4 uting Ihe siren without riera todien Me6S USING RELAYS OF DIRECTION INDICATORS Nel General Car direction indicaters are connected to the relays Ne Mazerc warning ight swch H KSD sensor tuning Egen different cases on arming 0 5260 on disarming 1 1200 sengor noifioation signet 0 5520 Set senstnty Adjust cernstivty Nie3 Harard warng tight s ch Hi kiemai zone 5 yrtch presses N cttterert camer are prog atned by computer bras FN 77 SENSOR TYPE ae v ne a Mi One manually adassted sens aa E n Ni 2 Two manually adusted two lew an Max Nite Two manay edusted gensors i Z Ned CSO sengor in shock and incinston mode MBE z redwi room ksa NNe5 KSD sensor only in nelination mode MEE ser ode Ran t NG KSD sensor oniy n shock mode MBE se
19. ter fans blocks of relays c avoid mounting system unit directly onto metal parts of vehicle to prevent accumulation of condensate in the system unit d mount system unit in a way wire connectors are going from the bottom side of the unit e avoid placing wires next to moving or hot parts of vehicle f avoid overload of alarm system circuits 0 cut off Circuit Curent ANS aeia faet le eel e iad lt 25A 7 unlock pulse cutrent D ariere eens lt 0 13 A y JOCK Pulse cunnen Io aieeaii a G lt 0 13 A v cut off optional output current cece eee eeeeeeees lt 0 13 A v siren drive current O ccc ccc cece rren lt 2A v right direction indicator control current 5 eeeeseeees lt 7A v left direction indicator control current 2 oo eeeeeees lt 7A 4 ALARM SYSTEM SET UP GN7 features up to 82 system settings Due to these settings GN7 can be adjusted to some particular vehicle or relevant customer requirements GN7 features are set using PIN personal identification number FN feature number and SN setting number codes Actions to be performed in the following sequence a open vehicle doors and leave it opened there is no need to open doors on entering PIN code by alternative way see user manual 7 3 b enter PIN code see user manual 7 2 or 7 3 close the doors c wait for approximately 12 seconds intended for remote control learning till system LED stops emitting triple flashes and sta
Download Pdf Manuals
Related Search