Home

QIG

1. default antenna on unit to install your antenna 6 Mounting the N Type external antenna While selecting the N type external antenna you must notice that the antenna should support Dual Polarization for 2T2R MIMO radio transmission The JetWave 3200 series external antenna mounting L plate is available for both SMA and N Type antenna Purchase the external N type antenna mounting kit from your sales Using the External Antenna Consult your system integrator or our technical support engineer to choose the suitable external antenna with SMA type or N Type connector for your application Different antenna supports different bands and different range of coverage Front Left The antenna of the Radio 1 There are 2 SMA connectors for MIMO radio transmission Front Right The antenna of the Radio 2 There are 1 2 SMA connectors It may be WIFI MIMO 3G or LTE antenna connector depending on the model you purchase Lightning Arrestor While you install the external antenna in outside area the Arrestor is a must accessory to avoid the environment attack through the antenna The arrestor protects the insulation and conductors of the system from the damaging effects of lightning For example the JWA Arrestor 5803 is 0 6G Arrestor for N Type Antenna Note gt When preparing the external antenna make sure the antenna can support Dual Polarization Most of the high gain antenna supports Dual Polarization gt Most of high gain external ante
2. ot pi Ant B gt M12 Ethernet for J etWave 3320 M12 zil M12 Ethernet for J etWave 3420 M12 Dual Power Input Digital Input Output Ant D Antenna No A WIFI 1 1 B WIFI 1 2 5 Antenna No ip c3c D Reserved GPS is A WIFI 1 1 B WIFI 1 2 C LTE Main D LTE Aux J etWave 3320 3320 M12 Appearance J etWave 3420 3420 M12 Appearance Connect up The system provides both DC power input and PoE power input DC Input Insert the positive and negative wires into the V and V contact on the terminal block connector The typical power source is DC 24V Powered by PoE 1 Connect the Ethernet cable to the Ethernet Port in the front of the JetWave 3200 Series The Ethernet Mta d port 1 is an IEEE 802 3at compliant PoE port 2 If you are connecting the JetWave 3200 Series the i ee pn PoE function is applied to the port Eth 1 Eth 2 is only mit available for data transmission 3 While selecting power source by PoE connect the gt other end of the Ethernet cable to the PoE Switch or _ o PoE Injector Then the AP can be powered and user can access its management interface through the cable The figure on the right is an example of Connect AP to the PoE injector Note Please choose Korenix Industrial IEEE 802 3at compliant PoE Injector or Switch as power input source Thus Korenix can provide better quality assurance for your network Mounting 1 Mounting the AP The JetWave 3200 series support
3. del you chosen gt 2 4G 5G Dual Band Antenna Ex 4 for dual WIFI radio 3 for WIFI 3G LTE radio gt Mounting Kit gt Quick Installation Guide Optional External Antenna Mounting Accessory includes gt Antenna Mounting L Plate gt 90cm RG 316 Extended SMA Type Radio Cable gt Wall Mounting Plate Note Different model needs different number of the accessories If you are not aware of the number please consult with our Sales or Technical Service Engineer Installation Hardware Installation Appearance i Ant A Fo Ant a T i m Ant C H ji am is i System LED J LED i i i i Reset r Reset i Ethernet ane i foe H Sallie i Port LED th2 a 1 9 Eth 2 M12 H Ct i e i 5 i ee Aha Fr i i 1 Eth 1 PoE Dual Power Input M12 PoE j p j a fate it i Digital Input Output il i ie gital Input Outp Ant B Ant D Ant B T OOE S T Ant D Antenna No Antenna No A WIFI 1 1 B WIFI 1 2 A WIFI 1 1 B WIFI 1 2 C WIFI 2 1 D WIFI 2 2 C WIFI 2 1 D WIFI 2 2 J etWave 3220 Appearance J etWave 3220 M12 Appearance i Ant A Ant C Ant A gt Ant C E zm D z peni Sa System LED 5 System LED SM Serial Port Serial Port EEn E RS232 422 485 RS232 422 485 Reset ise Ethernet Reset gt i Ethernet oy Port LED Eth 2 lt Port LED Eth 1 PoE T 3 2 Dual Power Input Eth 1 PoE 7i a Digital Input Output aer o at
4. e information through Web GUI gt Follow above Login steps and you can find the 3G Cellular Setup page Configure the related account info and check its status Note If you still can t access the Internet after checking the settings please send the 3G Status and Settings to the distributor for further help J etWave Korenix View Utility The Korenix View Utility provides you convenient tool to scan the network and configure the AP Step 1 Open the Korenix View Utility Must later than V1 5 4 Step 2 Select the correct NIC Network Interface Card from the NIC list Step 3 Click Discovery and then the Nodes and its IP address can be found and listed in Node list Fae ieee Combe le Te Goa ae beg Dep sole sie fe bee Ea cael Ha iise iT Sidon 1 ee Ne LEL ba L Step 4 After you scan the network select the AP and click MS oe a e A e ld Open Web GUI to access the web management interface P P iming Configuration Fle Famme You can also modify the IP address Netmask directly on Utility and then click Change IP to change IP settings ew Rat Note Please check the User Manual to configure the other ene ie o Augn iP software settings DHCP Client Enable Fera Uporade Bort Loach Lipgrede UP Check Conlin File r Open iiba Reboot Oreca Load Factory Gefeok f Troubleshooting What if I cannot access the Web based management interface Please check the followings gt Chec
5. k whether the power supply is OK try to power on the unit again gt Check whether the IP address of PC is correct in the same network segment as the unit gt Login the unit via other browsers such as Firefox Google Chrome gt Use Korenix View Utility to scan the AP and modify the IP address 5 Years Warranty Each of Korenix s product line is designed produced and tested with high industrial standard Korenix warrants that the Product s shall be free from defects in materials and workmanship for a period of five 5 years from the date of delivery provided that the Product was properly installed and used This warranty is voided if defects malfunctions or failures of the warranted Product are caused by damage resulting from force measure such as floods fire etc other external forces such as power disturbances over spec power input or incorrect cabling or the warranted Product is misused abused or operated altered and repaired in an unauthorized or improper way Attention To avoid system damage caused by sparks please DO NOT plug in power connector when power is on The product is in compliance with Directive 2002 95 EC and 2011 65 EU of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronics equipment RoHS Directives amp RoHS 2 0 Korenix Customer Service KoreCARE is Korenix Technology s global service center where o
6. korenix A Beij er Electronics Group Company J etWave 3200 3300 3400 Series Quick Installation Guide V1 1 The Quick Installation Guide is applied to Korenix JetWave 3200 Series Industrial IEEE 802 11n 2 4G 5G MIMO Wireless AP Bridge JetWave 3300 Series Industrial Ethernet 802 11n WIFI to 3G IP Gateway and JetWave 3400 Series Industrial Ethernet 802 11n WIFI to LTE IP Gateway The 3 product series are equipped with the same 802 11n WIFI technology the same hardware software platform and the same installation consideration for indoor or outdoor field box Please refer to the product datasheet and user manual for detailed product specification In the description below the JetWave 3200 series stands for the whole JetWave 3200 3300 3400 product series Preparation before Installation This chapter describes safety precautions and product information before installing the product Professional Installation Required 1 Please seek assistance from a professional installer for field installation or professional IT Engineer for indoor outdoor installation The engineers must be well trained in the RF Radio Frequency installation and knowledgeable for the Wireless AP setup and field plan 2 The JetWave 3200 series is distributed by distributors and system installers with professional technicians and will not be sold directly through retail stores Safety Precautions 1 To keep you safe and install the hardware properly please read and fo
7. llow these safety precautions 2 If you are installing Jet Wave 3200 series in the field box for your safety as well as others please seek assistance from a professional installer who has received safety training on the hazards involved Keep safety as well as performance in mind when selecting your installation site especially where there are electric power and phone lines Please note the following things as well gt Do not use a metal ladder gt Do not work on a wet or windy day gt Wear shoes with rubber soles and heels rubber gloves long sleeved shirt or jacket 3 If you are installing JetWave 3200 series in the indoor office or factory be aware of the power source and grounding must be well installed The professional Wireless IT Engineer can provide service for AP location channel and field plan to get better performance and coverage 4 Users MUST use the safety certificated PoE switch injector with the JetWave 3200 series The Korenix JetNet Industrial PoE Switch is recommended 5 When the system is operating with high gain antenna avoid standing directly in front of it Strong RF fields are present when the transmitter is on Note that Field EMD Lightning DAMAGE IS NOT COVERED UNDER WARRNTY Package Check List The product package you have received should contain the following items If any of them are not included or damaged please contact your local vendor for support gt JetWave 3200 Series Unit depends on the mo
8. nnas are installed in higher place than AP Get low power lost antenna cable in advance gt While installing the AP within metal field box connect the extended antenna cable to outside the box is must to avoid the Radio lost Web GUI Settings The JetWave 3200 Series provides web management interface for basic and advanced settings Before configuration please make sure your system meets the following requirements gt A computer coupled with 10 100 1000 Base T X adapter gt Configure the computer with a static IP address of 192 168 1 X 192 168 10 X X can not be 0 1 nor 255 gt The default IP Address of JetWave 3220 is 192 168 10 1 Bridge mode gt The default IP address of JetWave 3320 3420 Eth 1 WAN is 192 168 1 1 Eth 2 LAN is 192 168 10 1 and DHCP Server mode is enabled Router mode How to Login the Web based Interface gt Open IE and enter the IP address Default 192 168 10 1 JetWave 3200 series into the address jamii field You will see the System Login page If you fe iL vis bhiin ES pim a emr ee ee haree mrmr s bae beter Lija Se miei kF dont know the IP address you can use Korenix View Utility to discover the device find its IP address or change IP address gt Enter the name of Account Default admin and password Default admin respectively and click Login to login the main page of JetWave 3200 series J etWave 3200 WLAN Setup gt Go to the Wireless Set
9. s Din Rail mounting The Din Rail mounting kit is Din 35 compliant and pre installed in the back of the AP The JetWave 3200 series also provide celling mount plate as optional accessory The ceiling mount plate is available for both ceiling and wall mount a installation in for example the vehicle PE ET railway and warehouse 2 Ground Mounting the grounding it is located in the bottom of the JetWave 3200 series 3 Mounting the default antenna on unit There are dual band antennas for the JetWave3200 Series in the product package You can install the default antenna to the SMA socket on the front Each radio supports 2T2R MIMO technology and you must install 2 antennas for one radio 4 Mounting the default antenna for vibration environment You can purchase our external antenna mount kit accessories There are antenna mounting L plates and extended RF cable package to ease such mounting installation need The antenna mounting L plate is available for both N Type and SMA type antenna N pe fine External AF Cathe 5 Mounting the SMA Type external antenna If the default antenna is not suitable for your environment you can purchase the external antenna per your environment need While selecting the SMA type external antenna you must notice that the antenna should support Dual Polarization for 2T2R MIMO radio transmission You can choose SMA type Dual Polarization antenna and follow the same steps as Mounting the
10. up Choose the WLAN 1 or WLAN 2 you would like to configure gt The WLAN 1 Basic Settings allows you to Disable Wireless LAN Interface or configure the Wireless Mode SSID Output power etc Wireless Mode A service set of the wireless mode F which includes the AP Client WDS AP Wises WDS Client Redundant AP and Redundant Client modes E SSID A service set identifier SSID is a name that z identifies a particular 802 11 wireless LAN a A Broadcast SSID Network administrator can i choose to broadcast beacon messages of a virtual AP gt Select the other 802 11 Mode and the chance settings Radio Output power and data rate per your environment need gt Select the Security Settings Advanced Settings and Access Control of the Radio Refer to the user manual for detailed configuration Note Please check the User Manual to configure the other software settings J etWave 3300 3400 Cellular Setup gt The 3G LTE cellular module is pre installed within the system Plug in the 3G LTE SIM and make sure your account is available before you start the cellular connection gt Power off the device first Plug in the SIM card to the SIM socket and then power on the system gt Normally the system will directly connect to the Internet Service Provider ISP after power on gt If you are not available to connect to the ISP please check the account information with your ISP and then configure th
11. ur professional staffs are ready to solve your problems at any time Korenix global service center s e mail is KoreCARE korenix com For more information and documents download please visit our website http www korenix com downloads htm Patent No Taiwan Granted Invention 313547 Granted Invention 321415 Granted Invention 344766 Granted Invention 346480 Granted Invention 356616 Granted Invention 364684 Granted Invention 376118 Granted Invention 393317 Granted Invention 398066 Granted Invention 398125 Granted Invention 459757 Utility Model M 339841 Utility Model M 339840 Korenix Technology Co Ltd A Beijer Electronics Group Company Tel 886 2 89111000 Fax 886 2 29123328 Business service sales korenix com Customer service koreCARE koreni x com www korenix com CPQOOOW3400001

QIG

Contents

Download Pdf Manuals

Related Search

Related Contents