2 - Webee
Contents
1. F Button SIDE VIEW FRONT VIEW Webee Plugee Getting started Page 03 2014 Webee LLC All rights reserved The Webee logo Boss and Bees are trademarks or registered trademarks of Webee LLC webee GETTING STARTED WITH PLUGEE CONNECTING TO SMARTEE Adding to Zigbee Network To add the Plugee to the Smartee click on the Add Device function of your App and the Smartee will automatically connect your Plugee to the network For more detailed instructions check our Smartee User Manual Ifthe Plugee does not automatically join the network press and hold the Plugee button The Plugee will continuously blink as it attempts to join the hub Upon a successful joining of the Plugee to the ZigBee network of your Smartee the status LED will stop blinking If after following these steps the Plugee will not join the Smartee Zigbee network do as follows eMake sure the Plugee is powered up eEnsure the Plugee is within RF range of a routing device e Make sure the network on your Smartee is open for joining Keep in mind that once you clicked on Add Devices the network will be open for 60 seconds eCheck if the Plugee hasn t join another network the light will be static see the next step to learn how to remove it from a network in order to add it to a new one Once the Plugee is added to your Smartee you will be able to start controlling it trough your Webee App Removing from Zigbee Network If it becomes necessar2. GETTING STARTED WITH PLUGEE This document is the property of Webee L L C The data contained here in whole or in part may not be duplicated used or disclosed outside the recipient for any purpose This restriction does not limit the recipient s right to use information contained in the data if it is obtained from another source without restriction webee GETTING STARTED WITH PLUGEE INDEX Section 1 Mounting your Plugee INSTUCIONS Sumatra 03 DIMENSIONS botar ataca 03 Section 2 Connecting to Smartee Adding Plugee to Zigbee Network ooooooooccoooconoono0 gt 04 Removing Plugee from Zigbee Network 04 Section 3 Specs Electrical S PSCC AON rada 05 RF Characterisiies sepia arce 05 Section 4 Security Instructions Security Guidelines 06 Webee Plugee Getting started 2014 Webee LLC All rights reserved The Webee logo Boss and Bees are trademarks or registered trademarks of Webee LLC Page 02 webee GETTING STARTED WITH PLUGEE MOUNTING YOUR PLUGEE Instructions 1 Attach the plug from the appliance to be controlled into the receptacle of the Plugee 2 Attach the Plugee to wall receptacle Verify that the receptacle is powered If the receptacle is powered by a wall switch the wall switch must be kept ON at all times for the module to operate properly Dimensions 1 56 2 41 2 62 NE I I i O N Status LED ON OF
3. ment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help C Contains FCC ID W7Z ZICM357SP2 Webee Plugee Getting started 2014 Webee LLC All rights reserved The Webee logo Boss and Bees are trademarks or registered trademarks of Webee LLC
4. nsure about any of these instructions consult a qualified electrician Unplug unit when servicing connected appliances Follow all guidelines carefully if you have any questions contact us at support webeelife com Warning Each module outlet is rated to 12A only if the connecting cord is rated at 90C or greater Warning If a load greater than 12 amps is attached to the output the Plugee will be damage and will no longer function Warning The total current of the device is 12A Do not exceed this value Warning If a direct short is created on the output the Plugee will be damage and will no longer function FCC Information This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful inerference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equip
5. y to remove the Plugee from a Zigbee network then you must factory defaultthe Plugee To factory defaultthe Plugee A Remove the Plugee from the wall receptacle B Press and hold the Plugee s button C Reinstallthe Pligee into the wall receptacle while holding the button D After 2 seconds the status LED willturn ON E Once the LED is ON let go of the button F The Plugee will now be reset to factory defaults and begin scanning for a ZigBee to join Webee Plugee Getting started Page 04 2014 Webee LLC All rights reserved The Webee logo Boss and Bees are trademarks or registered trademarks of Webee LLC webee GETTING STARTED WITH PLUGEE 6 PLUGEE s SPECS Electrical specifications Description Min Typ Max Unit Rated 120 VAC Input frequency 60 Hz Operating temperature 0 40 G Storage temperature 20 50 C Operating Humidity 0 90 RH non condensing Output 12A General Purpose Wireless RF Characteristics Description Min Typ Max Unit RF Channels TX Strength Range Protocol Zigbee HA 1 2 Webee Plugee Getting started Page 05 O 2014 Webee LLC All rights reserved The Webee logo Boss and Bees are trademarks or registered trademarks of Webee LLC webee is SAFETY INSTRUCTIONS A Safety Guidelines To be installed and or used in accordance with appropriate electrical codes and regulations lf you are u
Download Pdf Manuals
Related Search