HVA/HVM - CoffeeZone.sk
Contents
1. The machine is now ready for use INSTALLATION AND START UP Adjust water temperature bv pressing the buttons on membrane switch Max temperature 96 C Min temperature 70 C Fn Increase the temperature Reduce the temperature m Place a glass or decanter under the hot water tap A Pull down the tap handle to start dispensing water B Release tap handle to stop dispensing CLEANING AND CARE clean the exterior of the machine use a soft cloth and liquid cleaning agent that is non abrasive ERROR MESSAGES LEVEL CONTROL Remove the power cord from the wall socket during anv installation work The high water level Clean the level sensor sensor is triggerd Replace before the low level Cables connected is sensor incorrectly The machine fills slowly Poor water pressure Water connection tap is not open Check water connection Restart machine TEMPERATURE CONTROL Temperature sensor out of range Temperature sensor is broken Cable loose 5 C 105 C Replace temperature sensor Check cables Heating time too long Restart the machine Solid state broken Replace element Element broken Replace solid state Overheating guard Check overheating tripped or broken protection The installation work and all re2. Drip Tray Insert Drip Tray Water Connection Power Switch CO e 2 INSTALLATION AND START UP Place the machine on a flat and waterproof surface that will support the weight of the machine Make sure air is able to circulate behind the machine minimum Connect the supplied water hose to the cold water connection using a 2 R connection A When pushing the machine into position make sure there is no interference to the hose to ensure proper water flow Water supply to the machine is the customer s responsibility according to instruction and advice from the supplier In areas with high level lime problem a descaling filter should be mounted Insert the power plug in a separately earthed wall socket See fig C Turn on the machine using the power switch See fig B that is located at the back of the machine The machine will now start to fill up with water and then heat the water The display will flash while the machine is filling with water See fig D While the machine is heating the current temperature J will flash in the display When the water has reached the preset temperature of 90 C the display will show a steady light See fig E
3. USER MANUAL E UM EN Part No 1730015 02 CONTENT keik O ER OC OOO o 2 AS M M M ii 3 kin a d noa 3 VA IE a cg ec cca ce 3 3 intended Use mamma am a sna muu voo os 3 FACES VSI UN ik 4 E AO EA EA E 5 A 2118171 ERa 6 alaalia 6 Srp P OCE dIE aaa 6 Adiusting Water Temperature naa 7 Dispensing NOt Water 7 8 RE 2 P a AEE EEN O Set machine for manual water Ml E cocinan id aia 10 84155 6 ICE enana A e A H Some important information may appear in textboxes seen below A IMPORTANT A CAUTIONI More INFO INFO INFO INFO GENERAL Thank vou for choosing a HVA HVM hot water machine We hope you enjoy it Always keep this guide close at hand for future reference Read the user guide before using the machine This guide contains important instructions for proper and safe use of the vending machine Never immerse the machine plug or mains Do not use the machine if the mains cable plug cable in water because there is a danger of electric shock The appliance is not intended for use by persons including children with reduced physical sensory or
4. com
5. e machine out of the reach of children Position the mains cable so that people cannot trip over it Keep it away from sharp edges and heat sources The new hose sets supplied with this appliance are to be used old hose sets must not be re used This appliance is not suitable for installation in an area where a pressure washer may be used This appliance must not be cleaned with a pressure washer For the optimal performance of the machine these parameters shall not be exceeded Maximum permissible inlet water pressure 800KPa 8Bar Minimum permissible inlet water pressure 200KPa 2Bar Maximum working temperature 40 C Minimum working temperature 10 C EI GENERAL Facts amp weight Height Width Depth 500 225 410mm 500 225 410mm Tank volume Power supply 7 5 Litres 220 230VAC IN 2200W 50 60Hz 7 5 Litres 380VAC 3N 6600W 50 60Hz Cold water connection Capacity Y External thread 18 litres hour Y External thread 67 litres hour Water purification filter Filling and heating time HVA HVM phase Option 16 5min Option 6min HVA HVM 3 phase OVERVIEW OF COMPONENTS FRONT Hot Water Tap Display E Temperature L Adjustment Buttons BACK
6. mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety Children should be supervised to ensure they do not play with the appliance Do not use the machine outdoors so it can be exposed to weather rain snow frost It will cause material damage to the machine Do not try to open the machine or repair it in any way To avoid danger only have the machine repaired in a technical workshop Service Centre or by a qualified person Remove the mains cable from the socket when the machine is not in use for longer periods To do this pull the plug not the cable This appliance must be placed in a horizontal position which is resistant to any water that may leak This appliance is intended to be used in household and similar applications such as Staff kitchen areas in shops Offices and other commercial working environments On agricultural estates By clients in hotels motels and other residential type environments Bed and breakfast type environments is damaged or the machine has fallen down If the mains cable is damaged it must be replaced by the manufacturer service agent or similarly qualified persons in order to avoid a hazard Only plug the machine into a properly installed earthed safety socket whose line voltage matches the technical data for the machine Place th
7. pairs shall be done by a qualified technician PROGRAMMING Set machine for manual water filling Use a decanter to fill up the water tank to the long sensor pin A Keep button B pressed while turning on the power switch D The display will show TI change the type of machine with buttons B or C TI HVA automatic T2 HVM manual Confirm the choice by holding down the buttons B and C at the same time for approximately 5 seconds Install the cover plug at the inlet valve E to avoid possible leakage DIMENSION SKETCH HVA HVM phase 500mm 225mm 410mm 240mm HVA HVM 3 phase 500mm 225mm 410mm 240mm For the warrantv to be valid the conditions for maintenance must have been followed according to our instructions proper precaution has been made and warranty claim been issued without delay The affected equipment may not be used during awaiting service if there is any risk that the damage or defect would worsen The warranty will not cover consumption supplies such as glassware normal maintenance such as cleaning of filters contaminations in water lime incorrect voltages pressure or adjustment of water amounts The warranty will not cover damages of defects caused by incorrect handling and operation of the appliance FOR SERVICE Please contact your dealer Your Dealer Crem INTERNATIONAL www creminternational
Download Pdf Manuals
Related Search