Quick Start VSP198S
Contents
1. TSC SECAM Step 4 DVI Input Used to input DVI signal from DVI player or computer with DVI connector Step 5 VGA Input player or computer with VGA connector VSP 198CVS Quick Start Rev 1 0 Page of 3 Step 11 10 100M interface Used to connect the computer or console Support the speed of network connection with 10M or 100M Step 12 RS232 interface Used to connect the computer or console Step 13 USB interface Used to connect the computer or console Sending card module port Power has been already supplied by video processor itself no external power supply needed for sending card Step 14 Sending Card interface Step 15 Power Interface and Switch AC 85 264V 50 60Hz IEC 3 Power Interface Step 16 Power On Connect with power cable press the POWER and the power indicator is turned on and after 10 seconds the monitor will be switched on and get into working status Front Panel Operation Local Control VERE PACES SOR User Guideline Inputs cable outputs cable control cable power cable were connected to interface finish turn on the power switch user guideline The fist step set up OLED display language The second step set up output format The third step set up LED screen height size The fourth step set up LED screen width size The fifth step set up LED screen horizontal size The sixth step set up LED screen Vertical size The seven2. VSP 198CVS Quick Start NOTE For full installation configuration and operation details please refer to the VSP 198CVS user manual This guide provides quick start instructions for an experienced installer to set up and operate the VSP 198CVS Installation and cabling features Rear Panel 2 2 a a Ga rYale li 11 12 ih coe Connections DG CVBS Input 2 Power Switch 2 VGA Input 3 HDMI Input SDI Input DVI Input SDI Loop Out DVI Loop Out Push button switch 67 DVI Output 10 100M Interface VGA Ouput USB Interface 0 Power interface RJ11 RS232 Interface AD 19 Sending card interface GOOWOHY Step 6 HDMI Input HDMI A interface can be compatible with HDMI inputs Step 1 Mounting Turn off or disconnect all equipment power sources Step 2 SDI Input rough Standard BNC connector support Step 7 SDI Loop Through Output 3D HD SD SDI Standard BNC connector can connect Step 3 CVBS Input Composite video input BNC connector the device with SDI input or SDI monitor Step 8 DVI Loop Through Output Can connect the device with DVI input or DVI monitor Step 9 DVI Output Connect to the monitor or LED screen qi which has DVI interface Step 10 VGA Output Can connect the device with VGA owe input or VGA monitor 2 J Support composite signal include PAL N
3. modes Screen has no output image The forth step press MENU return to TEXT 1 Check if connect the wrong interface OVERLAY rotate the knob choose ABOVE BELOW 2 Check if the input and output interfaces are in to select the layer position for IMAGE B good connection The fifth step press MENU return to TEXT OVERLAY rotate the knob choose BLEND LEVEL and set the image display transparency regulating range 3 Check if support the resolution 4 Check if select the right signal source between 0 16 Display flips The sixth step press MENU return to TEXT Enter into the Menu option select SYSTEM then OVERLAY rotate the knob choose the color value select FLIP push OK rotary select OFF and The seventh step you can view the effect through the press OK key to ensure screen to get a better setting There is no audio output Check if input the wrong signal only SDI HDMI supported by DVI input are available for audio The first step LAN physical connection Connect VSP monitoring 628S and router with network cable then connect Screen protector installation computer and router with network cable also use the LAN port of router WAN port is used for connecting to outer net The second step IP address setting processor s default IP address is 192 168 0 100 a labeled step 1 This side is applied to the screen How to Realize Single Image Switching 3 Align and apply the exposed portion along
4. n choose ON it can realize the main and sub picture exchange ALPHA Can set the image display transparency regulating range between 0 16 SELECT Can choose to set the size or position of IMAGE A or IMAGE B individually VSP 198CVS Quick Start Rev 1 0 Page 3 of 3
5. nd the image will be zoom in to the top direction from its bottom part V DOWN Zoom in vertical and the image will be zoom in to the down direction from its top part V UP DOWN Zoom in vertical but in both top and down direction from its middle part H LEFT Zoom in horizontal and the image will be zoom in to the left direction from its right part H RIGHT Zoom in horizontal and the image will be zoom in to the right direction from its left part H JEFT RIGHT Zoom in horizontal but in both left and right direction from its middle part CENTER Zoom in 4 corner direction from center VSP 198CVS Quick Start Rev 1 0 Page 2 of 3 How to Realize the Text Overlay Setting Common Questions and Solution The first step press MENU button rotate the knob choose LTEXT OVERLAY 4 and enter KTEXT chock if POWER key lights If the light goes OVERLAY press the knob to confirm out please check if power is disconnect and press The second step rotate the knob choose TEXT POWER key again OVERLAY mode choose ON TEXT OVERLAY function open The third step press MENU return to TEXT OVERLAY rotate the knob OLED screen displays Screen is black after boot 2 Check if input the signal if screen displays lt NO INPUT gt then there is no input signal 3 If there is input signal press SOURCE key and menu options select 13 modes in PRESET or select switch the signals and the screen will be normal BLEND which includes two
6. one side The first step boot the system default CV1 to the current of the screen Lift and reapply until correct Peel off the How to realize LAN remote control settings 1 Clean the device screen throughly with cleaning cloth Make sure the surface is completely dry before you apply the screen protector 2 Peel down a small portion of the PET material layer input source key light and scintillation if need reset of the mask and slowly brush down seamless switching other source such as DVI direct 4 Remove the electrostatic layer labeled step 2 light touch DVI key Gently brush out any air bubbles by the air bubble The second step choose DVI buttons button lamp CV1 scraper destroy and DVI key light and shining can realize Screen protector removal single image of input signal source switching input The screen protector film can be easily removed by signal source by original CV1 switching to DVI The releasing the air vacuum which can be done by same method can be switched CV2 VGA1 VGA2 1 Using a piece of strong adhesive to lift one of the DVI HDMI SDI corners How to Set up the PIP 2 By sliding a thin piece of plastic polymer between the screen protector film and the device Note screen protector can be cleaned with water and used repeatedly Press the PIP button button led light turn on enter the pip function menu LAYOUT Can choose PIP layout SWAP IMAGE It can set PIP to swap exchange whe
7. th step set up input source The eighth step up save How to Set up the SPLIT The first step pushress the SPLIT button the button led light will turn on enter the SPLIT function menu The second step push and turn the knob will enable open split function H TOTAL LED screen Horizontal total size V TOTAL LED screen Vertical total size H POS this device display image Horizontal size V POS this device display image Vertical size H SIZE this device display image Width setting V SIZE this device display image Height setting RESET Restore the factory Settings How to Set up the Size and Position of the Single Image The first step press the SCALE button enter the SCALE function menu The second step touch the knob and turn the knob open split function H SIZE Width setting V SIZE Height setting H Pos Horizontal phase setting V Pos Vertical phase setting How to do customized output resolution The first step push MENU button to open the main menu The second step turn Knob and go to lt OUTPUT FORMATS The third step push knob and confirm to go into the lt OUTPUT FORMAT gt menu STANDARD standard resolution CUSTOMIZED user defined resolution setting a How to Set up image zoom The first step push MENU button to go into the main menu The second step turn Knob goes to ZOOM menu The third step push Knob to confirm to go inside ZOOM menu V UP Zoom in vertical a
Download Pdf Manuals
Related Search