Home

USER MANUAL - Carts & Wheels

1. recovery service 7 3 1 Assembly disassembly the battery pack 1 Cut off the power supply of WindRunner unplug the charging cable turn over and put aside place a cushion or soft cloth on the ground surface to avoid scratching of the hub 2 Unscrew the four fastening bolts shown as figure below with an internal hex wrench then take out the battery pack 7 3 2 Improve the cycle life of the battery pack WindRunner self balancing electric vehicle user s manual Lithium battery packs may emit gases when working so the battery pack can t be completely sealed Avoid dropping into a water pit and do not immerse the battery pack in water If you have to pass a water pit please be sure to a Make sure the maximum depth of water pit is not more than 6cm m Try to speed down and slowly pass to avoid splashing of water After you have passed the water pit try to leach and dry by inclining the WindRunner forward and backward respectively for about 10s Avoid using WindRunner under 10 C or above 40 C Do not put the battery pack directly under the sunlight Please store the WindRunner at a dry and place to keep the battery dry and clean If the WindRunner is not used for long period beyond 1 month please fully charge the battery dismantle it and put it in a cool and dry place a Even if powered off the WindRunner is also slowly consuming the electricity If not used for more than 1 month the
2. Beijing UPTECH Robotics Technology Co Ltd Address F 4 China National Aviation Technology Building No 56 Zhichun Road Haidian District Beijing Tel 86 010 82114870 4887 extension 803 809 Fax 86 010 82114870 4887 extension 828 400 toll free 400 088 6780 China Mainland Email alphis 163 com Web www windrunner cn en
3. Operation mode intelligent remote key contour and functions WindRunner self balancing electric vehicle user s manual 2 4 1 Function list D ON OFF Unlock For starting or turning off the WindRunner To start it you press it once Once you start the WindRunner if no driver is standing on it press it once to turn off for safety reasons if the WindRunner has been started and the driver is standing on it it should be not powered off Under the lock mode press this button to unlock A Lock if powered on press this button to start the lock mode Under lock mode any movement or inclining in the mainframe may trigger an alarm wheels locked up cause vibrations and trigger the alarm hee Battery capacity indication press and hold this button on the display panel to show the current battery capacity of the WindRunner There are total five LEDs 1 5 blue LEDs respectively mean 5 divisions of battery capacity if 5 blue LEDs lit up means that the battery capacity is full 1 red LED means about 20 of batter capacity is left If you press and hold this button and only 1 red LED flicker it means that the battery capacity has been approximately used up Speed limit the WindRunner has three riding modes beginner mode Speed limit A mode and normal mode The maximum speed and reaction sensitivity under three operating modes are quite different If powered on press this button to toggle three modes Under the
4. beginner mode a red LED located on the display panel shall g WindRunner self balancing electric vehicle user s manual steadily under Speed limit mode the LED will be blue and glow steadily under normal mode the LED will not light up 2 5 Test riding Now you have installed the WindRunner properly and primarily understand the intelligent remote keys Please take the following steps before test riding 1 Stand beside or behind the WindRunner Keep the foot mat at a basic level position Hold the handle with one hand and press the ON OFF of intelligent remote key for 1s with the other hand and the WindRunner shall start 5 LEDs on the central display panel shall come on in sequence meanwhile accompanied with vibration and buzz similar to that of starting the engine of acar After the buzz disappears the WindRunner self test will be complete Keep the foot mat basically leveled then tap any one foot mat lightly with your foot You may hear a very short buzz and then the wheels of WindRunner begin to move and enter into the power assistant mode At the moment of startup keep the WindRunner upright and the foot mat basically leveled with the operating bar at middle position Otherwise the intelligent self test logic may determine that the WindRunner is unsuitable for starting and unable to start Refer to 5 4 for details WindRunner self balancing electric vehicle user s manual 2 Under power assistant mo
5. by from the back of a pedestrian give a warning to pedestrian and decelerate Try to pass from the left side If face to face with pedestrian pass from the right side and slow down WindRunner self balancing electric vehicle user s manual If the pedestrians are crowded slow down and pass with the speed just the same as that of the pedestrians If there is enough safe space for passing you may pass try to avoid passing through the crowd of pedestrians When riding together with another driver on a WindRunner keep an appropriate safe spacing avoid any hazards and obstacles unless there is enough space for the safe passing of pedestrians Otherwise it is forbidden to ride side by side Do not stop and stay at a place which will cause the WindRunner to impede on the passing of pedestrians Do not ride at place without enough light If necessary please slow down and keep vigilance it is better to use an external running light to ensure the lighting When you ride the WindRunner you should be 24 30cm higher than your body size when passing the door frame or closing the door entrance tree branches various labels nameplate or other obstacles above please keep a sharp vigilance and avoid any injuries WindRunner self balancing electric vehicle user s manual Care to the space above your head please ride with the correct posture While riding relax and keep both your knees and elbows bent lightly R
6. container lateral container or backpack as recommended Do not put any other things onto the foot mat The total carrying capacity of the handle is no more than 5kg otherwise the balancing ability of the WindRunner will be adversely affected Before handling and moving the WindRunner please confirm that the WindRunner had been powered off and handled by both people together To avoid any damages to the fender do not lift the WindRunner by the fender Be careful not seize your fingers between tire an fender WindRunner self balancing electric vehicle user s manual Prior to riding the WindRunner please carefully check the WindRunner If you find any loose points or damages please do not ride until the troubles have been resolved Periodically maintain your WindRunner according to chapter 7 and 8 and appendix 1 6 5 Intelligent safe alarm protection Under the following situations the WindRunner shall automatically slow down by automatically limiting its maximum speed to a safe level Advance speed too high If you ride the WindRunner too fast beginner mode 5km h Speed limit mode 10km h normal mode 20km h the WindRunner handle shall generate a force to push the driver backwards to limit its speed During this moment your body will have been tilted too high and your speed too fast The Speed limit mechanism of the WindRunner will be triggered and during this moment please adjust your body s tilting
7. degree to keep a spacing about one fist between your body and operating bar Low battery capacity When the voltage of battery is reduced to 40 and below its maximum speed under normal mode shall be gradually reduced That is begin to restrict its speed if its speed is still less than 20Km h Typically if the battery capacity is only about 30 then its maximum speed is about 15km h WindRunner self balancing electric vehicle user s manual auto Speed limit Intelligent safety alarm ISA under the following situations the WindRunner shall automatically restrict its speed to about 5km h and continuously shake give an alarm buzz to the user and all LEDs will be red and flicker quickly This mechanism is called the intelligent safety alarm Reverse speed too high When you ride the WindRunner and reverse too fast reverse beyond 5km h the intelligent safety alarm will be triggered Riding in reverse too fast is dangerous Please stop immediately and change to advance mode after you have made a turn Overload or stay on a ramp for a long period When the load is beyond the designed safety value of the WindRunner for any specified period which usually happens durin WindRunner self balancing electric vehicle user s manual situations such as steep slopes deep pits the weight of driver s body is too high or has stayed on a ramp for a long period and has caused the WindRunner to overloaded e
8. lacquered bright yellow car paint Luggage support and luggage compartment at both sides parking safety lock LED Optional parts running headlight handle frame removable seat parking frame portable charg and standby battery WindRunner self balancing electric vehicle user s manual Appendix A More maintenance instructions A 1 Replace the tire Replace the tire after worn to a specified extent The user may purchase the special purpose tire and then replace by his or herself You can also replace the tire at an UPTECH authorized agent distributor For G1U urban type if the tire pattern is worn up to a furrow less than 2mm deep or scratched or failed renew as soon as possible to ensure high safety For G1X all terrain type if the salient discontinuous pattern at the apex of tread is worn and invisible or the tire is swelt scratched or defects are found renew it For replacing the tire only pull out the decorative cap of hub and remove the three lock nuts with sleeve Then take out the tire The right figure is an illustration for replacing tire take G1U urban type as an example It is similar to the replacement of an all terrain type tire A 2 Replace the fender WindRunner self balancing electric vehicle user s manual If the fender is damaged the user may replace it on his or her own You can also replace it at an UPTECH authorized agent and distributor The figure below shows an illustr
9. shall be further detailed in the next chapters The driver may progressively find out the features of all working modes during the riding test and make a good using WindRunner self balancing electric vehicle user s manual 4 Use the intelligent remote keys 4 1 ON OFF This function is suitable for the WindRunner unmanned Press the ON OFF on the intelligent remote key for 1s to turn on off the WindRunner Under the OFF state press and hold the ON OFF for 1s to start the WindRunner 5 blue LEDs on the display panel shall come on followed by a shake and buzz at the moment the WindRunner is powered on Under the power on state press the ON OFF button for 1s Once the WindRunner is turned off all LEDs on the display panel will also turn off After powered on for more than 10 minutes the WindRunner will be enter idle standby mode and then the system shall be automatically powered off At the moment of powered on five blue LEDs on the display panel shall be lit up one by one 4 2 mode switch WindRunner self balancing electric vehicle user s manual After the WindRunner starts the system will be in standby mode At this moment press the Speed limit of intelligent remote key The LED at the lowest part of display panel shall be red and glow steadily accompanied by a buzz At this moment if the driver gets on the maximum speed of WindRunner shall be not more than 5km h gentler operating than that in no
10. the optimum performances of the WindRunner During cleaning you may wipe the mainframe of WindRunner with a soft cloth soaked in clean water It is forbidden to use alcohol gasoline kerosene acetone or other corrosive chemical solvents to clean the WindRunner All the above may cause surface damage internal part failure and warranty qualification loss Wash the tire and fender with a household shower or water pipe but avoid direct spraying to the mainframe After washed leach and dry as soon as possible store the WindRunner in a well ventilated place to dry This will protect some steel component parts against rust Remove the foot mat and wash it with clean water WindRunner self balancing electric vehicle user s manual When cleaning the WindRunner ensure that the WindRunner is powered off and charging cable is withdrawn and tightly fastened to the rubber cap Otherwise you may suffer an electric shock or serious troubles It is strictly forbidden to directly spray and wash the WindRunner with a water hose and head used for washing car Do not wholly soak the WindRunner in water This may cause serious damage due to the moisture or water accumulated inside it 8 2 Check whether the screw is loose or not Periodically check the assemblies such as hub operating bar battery pack fender and housing of display panel etc Shake lightly to observe whether the assembly is shaking or loose if
11. the working gloves to protect your hands from dirt and scratches 2 3 2 Assemble the operating bar WindRunner self balancing electric vehicle user s manual Assemble the handle onto the upper segment of operating bar and then fit the upper segment of operating bar with its lower segment together gt m Cans 2R SSS release handle Wp LLIN a YK it 7 I ad U SB a 1 Hold the nuts 2 Insert the operating bar A 7 o inside revolve the Yc to the steering shaft Si Ey f quick release handle CW A A I YF i ee a d Insert the operating bar into the steering shaft Hold down the quick release handle WindRunner self balancing electric vehicle user s manual When assembling or removing the operating bar with quick release handle you should first remove the decorative cap of operating bar then tighten the quick release handle turn it until the last turn is at its final place Then hold down the handle upward If too tight the handle shall be unable to hold down If too loose the handle may be disengaged fall off and lead to a hazard 2 4 Intelligent remote keys Each WindRunner has been equipped with two identical intelligent remote keys One is for operating and the other is for standby and precautions against loss or damage See figure below for the appearance of intelligent remote keys and functions of buttons a On Off ge Sa
12. vehicle user s manual Trademark registration and legal notices The WindRunner is a trademark of Beijing UPTECH Robotics Technology Co Ltd hereafter briefly called UPTECH or UPTECH Robotics ARM is the trademark of ARM Company Any other trademarks mentioned in this manual and all concerning rights shall be the proprietary of their owners UPTECH reserves all rights for WindRunner and 8 shape logo This manual was compiled by UPTECH UPTECH owns all copyrights of this manual and without the prior formal permission from UPTECH any organizations and persons are forbidden to duplicate or distribute all or part of this manual to others WindRunner self balancing electric vehicle user s manual About this manual Thank you for your choosing our WindRunner electric self balancing vehicle This manual will help you follow all the safe riding instructions and obey the riding skills listed in this manual and you can enjoy a safe and pleasant ride to ensure a better riding experience to perform the basic operations of WindRunner before riding to master routine maintenance and also contact of after sale services to Understand all aspects of performance maintenance skills and troubleshooting to solve any problems as soon as possible This manual derives accordingly and is applicable for WindRunner G1 series including G1U G1X WindRunner self balancing electric vehicle user
13. 1U all terrain type is applicable for grassland earthy slope forest land and muddy rugged mountainous road On these road situations G1 terrain type may reach its optimum shock absorbing effect and optimum tire adhe WindRunner self balancing electric vehicle user s manual effect Although G1U urban type may be also rode on some rugged and uneven road with difficulty its tires will have poor adherence lower safety and shock absorbing effect than that of all terrain type tire So more caution should be considered when riding B 3 About intelligent Speed limit The WindRunner has adopted the battery capacity based intelligent Speed limit algorithm According to different battery conditions cycle times battery ageing residual battery capacity the internal processor of the WindRunner may automatically determine the maximum Speed limit value In good conditions if the battery capacity is gt 60 the WindRunner may continuously ride under balance mode normal mode in a speed slightly higher than 20km h In good conditions if the battery capacity is lt 60 the maximum Speed limit of the WindRunner may be reduced gradually with the reducing of battery capacity Ifthe capacity of any one of both batteries is lt 10 the WindRunner shall give a low voltage alarm buzz mainframe shake and the foot mat will face up greatly to warn the driver to get off and charge as soon as possible Under these situati
14. able 20km h normal mode 10km h Speed limit mode 5km h beginner mode Typical 20 40km 2 4h intelligent remote key ON OFF lock Speed limit battery capacity display Cement road asphalt road other basically leveled road surface With slope not less than 15 Waterproof depth not more than 5cm no water immersed into the chassis Black matte lacquered bright yellow car paint Luggage support and luggage compartment at both sides LED running headlight handle frame removable seat parking frame portable charger WindRunner self balancing electric vehicle user s manual 10 2 WindRunner G1X all terrain type A large size and low pressure all terrain tire is suitable for various land forms It also has a high adaptability for rugged and uneven land forms and low shock The operating bar may be easily removed and put into most of SUV luggage compartment N W load capacity 55kg carrying capacity 20 110kg Dimensions LxW 52cmx81cm height of operating bar adjustable Maximum speed 20km h normal mode 10km h Speed limit mode 5km h beginner mode Batt stamina 15 30km Charging time 2 4h Remote key intelligent remote key ON OFF lock Speed limit battery capacity display Various road surfaces grass land earthy land rubble land and sand land With Trafficability slope not less than 15 Waterproof ability Waterproof depth not more than 5cm no water immersed into the chassis Color Black matte
15. aise your head and keep your body in a relaxed posture Please do not reverse unless you are certain to avoid any obstacles If your path is clear you may slowly reverse a few steps e When riding keep in mind that your body shall be kept at least one fist away from operating bar and handle Do not lean your body on the operating bar or handle That s very dangerous and may cause crush amp injury 6 4 Active protection instruction Please carefully read this manual and watch the video in DVD about safety riding instructions Understand and master these instructions WindRunner self balancing electric vehicle user s manual Do not lend your WindRunner to others unless he she has carefully read this manual and seen the DVD about safety riding instructions Please wear the safety helmet and tie the ribbon on the helmet No matter when you ride the WindRunner please wear the qualified safety helmet The driver may wear the gloves eyeshade shin guard and kneepad etc according to the riding situations and his her previous riding experience If you feel unwell or unable to obey all notices or warnings in this manual please not ride and not ride under the effect of alcohol or drugs When you hear a continuous alarm see Speed limits or are at a low battery level please get off and charge your batter as soon as possible to ensure high safety When carrying something please use the front storage
16. anual The mainframe is relatively heavy If it is difficult for one person to handle please request the help of another person Please keep hands in the correct position when handling the battery pack or hub At the moment of handling please grasp the hub with hands not the fender otherwise the fender may be damaged and possibly injure your hands 8 5 Repair Apart from retightening the screw replacing the tire fender and battery no other component parts of the WindRunner can be repaired by the users themselves If you find any unsolvable problems please contact us or our authorized service agents Apart from service engineers authorized by UPTECH no one else is permit to disassemble the WindRunner otherwise the warranty terms shall be invalid Any personal damages and or troubles shall not be the responsibility of UPTECH WindRunner self balancing electric vehicle user s manual 9 Troubles and alarms 9 1 FAQs and troubleshooting 1 Unable to power on Please verify whether the battery of intelligent remote key has sufficient capacity or retest the power after the battery is replaced If powered on only when the intelligent remote key is quite close to mainframe it means that the battery of the intelligent remote key has been approximately used up and you are now required to replace the battery consult 4 5 of this manual If the battery of the intelligent remote ke
17. ase contact the factory for inspection An Internal fault alarm A hint at other hardware error or unspecified trouble Do not continue riding Please contact the factory for inspection WindRunner self balancing electric vehicle user s manual 9 3 Spare parts for repairing and replacing Please do not hesitate to contact your seller to learn how to maintain or replace the component parts To contact a local authorized agent distributor login to www windrunner cn en the official website of WindRunner If no authorized local agent distributor responds to your inquiry please turn this manual to the last page and contact UPTECH to learn how to repair or replace the component parts 9 4 Reporting your troubles Although the WindRunner products have passed many strict tests in factory it is still inevitable that some defects unknown and new troubles may arise If you find any troubles not specified in Chapter IX please do not hesitate to contact UPTECH We shall try our best to solve your problems Thanks for helping us to continuously improve our product quality WindRunner self balancing electric vehicle user s manual 10 Datasheet 10 1 WindRunner G1U urban type N W load capacity Dimensions Maximum speed Batt stamina Charging time Remote key Traffic ability Waterproof ability Color Optional parts 49kg carrying capacity 20 120kg LxW 46cmx65cm and height of operating bar adjust
18. ation for replacing the fender 1 First turn the mainframe sideway Then after the tires are removed hold down the front and rear decorative strips Unscrew the two screws of fender but do not remove 2 Unscrew the four screws for fixing the fender and place on the gearbox Then raise the fender 4 lor 1 i Loosen the screws that hold down the decorative strips and fender Remove the fender screws then remove the fender A 3 replace the foot mat WindRunner self balancing electric vehicle user s manual 1 release 2x screw decoration strip Prior to replacing the foot mat loosen or remove the front and rear decorative strips A 4 replace the gear oil WindRunner self balancing electric vehicle user s manual Replace t nse Narea if any damage 7 i ole About every 5000km of the WindRunner run charged 200 300 times replace the gear oil The steps are as followed 1 Dismantle the tire 2 Vertically place the mainframe of the WindRunner to pump out the gear oil 3 Remove the oil hole sealing bolt as shown in the figure Care to keep the O rings of screws 4 4 Use a clean injector with a tube or needle gt 1mm to insert into the bottom of oil hole Slowly suck up the gear oil Repeat this step until no gear oil is left 5 Refill the new gear oil 100ml the OEM transmission oil for motorcycle or car is appli WindRunner self balancing elec
19. ay panel shall indicate the battery capacity and most of the LEDs will light up Release the battery indication and the LED on the display panel will not indicate the capacity of battery When the battery capacity is reduced to a specified value the WindRunner shall gradually reduce the maximum riding Speed limit with the reduction of battery capacity When the battery capacity is less than 20 the system shall automatically restrict its speed to 10km h and below Meanwhile the battery LED will flicker red If the battery capacity is lowered continuously it Shall trigger the intelligent safety alarm Then the WindRunner mainframe shall vibrate and foot mat automatically inclined backward which will give notice to the driver to get off an charge as soon as possible WindRunner self balancing electric vehicle user s manual 80 100 60 80 40 60 20 40 10 20 After a long distance ride please stop riding every 20 30 minutes to have a short rest to check the battery capacity Do not check while riding While riding the driver must pay close attention to the road conditions If the driver checks the battery capacity and is not wholly focused on riding it may result in a crash and or serious injury WindRunner self balancing electric vehicle user s manual 4 5 Replace the battery of the key The intelligent remote key uses 23A battery 12V with the normal service life of about 1 y
20. battery may be over discharged and this may seriously reduce the service life of the battery E Do not directly store the battery after its power used up Because this may cause over discharging and give adverse effect to the service life of the battery WindRunner self balancing electric vehicle user s manual For individually stored batteries please charge it at least every 3 months All lithium batteries have a slow self discharge If not charged for long period it may also cause the battery to over discharge If the battery capacity is very low please do not ride any further and charge immediately If the WindRunner gives the low voltage alarm shakes or shows a Speed limit it means that the power has been approximately used up At this moment it may still work for about 3 5km or 8 10km under power assistant mode If you continue to ride for long period it is unsafe and may possibly cause the battery to over discharge Which may reduce the cycle life of the battery Only the built in battery charger of WindRunner or OEM charger from UPTECH may be applicable Do not use any other chargers Otherwise the service life of battery may be reduced or battery damaged Ifa battery has been out of normal work and after test by UPTECH have found that its life cycle has been expired we strongly recommend that you replace the battery or repair A new battery together with a battery that may be expired may
21. cictditidaddiadadadadididadadadididddaddiadadandledidadegidddidddaddiadadiddiedidadadidbdidddaddiadadiddiedidadagacacaun 31 Ao HOC IMO Ge a E E mnennnsenE neuen c eRe OR Ronee CECE cuEemEees 34 AA Battery MALACO eneore eraai 35 4 5 Replace the battery Of the key sssssssssssrrnsnrrrsnrrrsnnrrnsnrrrnsnnrrsnnnrnnnnrnnnnrrnnnnrnnnnrnnnnrrnnnnrnnnnrnnnnrnnnt 37 RON TO T IE EEEE EEEE EEEE EE E E EEEE SEPEren E E ET TNE EEA EEEE TEENETE EAAS SA SamI Te W UI COVEN sirsie occ ie ci ado lio tol oo AA 5 3 Verify the startup of beginner mode SEPO O GE CO Perterrttr errr rm tT eter E E entre ttre r errr ern tr en tn ener entre ntn ert r ttt De Ge GO a PEPE EE E E E E EE A nce E E E Dx Move LO Vall and oa N OE ESEE EEEE SA Pece erae ana SUC eE EE EEEE EEEE ESEE EEEN EEE EEEE EEEE 58 M ke a tUM aan sng anuion snes acuscna nad once onened aieresaceeccuse nanos ceamenacnece WindRunner self balancing electric vehicle user s manual SEE E EA T ey ire cheese eek hee Coa Ieee E OES Ue T REL cue EES REL e NOGARO E N T N T E N T 49 Bot WSe The PIN r ae eE ME WO erT 50 LE Use TNE OEE TO E xccuean eer crveasec usenet cveeusen neue eek eer usin de ieusey neue eva e eves dees ene ue ernie cee ene 52 6 Safe NANG DEVS UI WC NOUNS ii eas ed avo ir ea een ie av i ea eo a vt dove eda nanan 54 ity OU MUSE SURG COSY cara ne nncncsnncnisrcaccnec AEA 54 Guz SEMICUY MOMDIGGel cuuacteet ounce cence atecciieigee a E E 55 6 3 Driving manners safe riding wiiscrcv
22. ctric vehicle user s manual 4 foot on sensor location 3 2 1 Beginner mode 5km h max The beginner mode is one of the balance modes especially suitable for a new or unskillful rider Press the intelligent remote key Speed limit and when you hear a very short buzz or tick and the red LED at the lowest part of display panel comes on it means that the beginner mode is entered Under this mode the maximum speed of WindRunner is limited to 5 7 km h and operating response will be very slow This mode is suitable for the new riders to learn and master riding skills 3 2 2 Speed limit mode 10km h max WindRunner self balancing electric vehicle user s manual The Speed limit mode is one of the balance modes suitable for the driver operating under complicated road conditions for example too much pedestrian or uneven surface of path While in beginner mode press the Speed limit button on the intelligent remote key You may hear a very short buzz or tick and the red LED at the lowest part of display panel will change into blue and glow steadily This means that the Speed limit mode is entered Under this operating mode the maximum speed of WindRunner is between beginner mode and balance mode for complicated road conditions 3 2 3 Normal mode 20km h max The normal mode is another balance mode suitable for experienced drivers on good road conditions e g no pedestrian and even path This mode
23. d gently shift your buttocks back as if you are ready for seating backward to decelerate and stop the WindRunner 2 After you ve completely stopped uniformly distribute your body s weight onto the center of the foot mat to stabilize At this moment if you continue to incline backward then the WindRunner shall move backward Specify a point to practice stopping the WindRunner and keeping stability WindRunner self balancing electric vehicle user s manual Typical decelerating and stopping action Try to decelerate and stop gently and progressively Also try to reduce sharp stops Move back the weight of driver s body gently from the moving direction to slowly stop the WindRunner During deceleration and stopping try to avoid wet and slippery roads because a sharp stop on it may cause the WindRunner and tires to skid and thus the driver may fall or get injured WindRunner self balancing electric vehicle user s manual 5 8 Make a turn The WindRunner shall turn according to the motion of your handle Inclining your handle left or right may cause the WindRunner to turn to the corresponding directions 1 Firstly do exercises of turning at any safe site for riding Slowly incline your handle to the direction you want to move and the WindRunner shall turn at site until the angle you required is achieved Then return the handle back to its normal position Repeat to turn left and
24. de you may slowly push the operating bar forward or backward the WindRunner shall accompany a forward or backward movement Turn the operating bar right or left lightly the WindRunner shall also turn along the direction of your turning of operating bar 3 Next please press the lock of intelligent remote key once until you hear a sound or tick One red LED on display panel shall come on Just then you may push the operating bar forward and backward The WindRunner shall shake and give an alarm sound At this moment if you want to draw the WindRunner you will experience difficulty Simply press ON OFF to unlock 4 Press and hold the battery capacity indication of intelligent remote key and the corresponding LED on display panel shall come on Once the key is released the corresponding LED light will turn off The battery indication of a new WindRunner is approximately 2 5 blue LEDs that is 40 100 battery capacity 5 Press Speed limit and the red LED on display panel comes on Once this button is pressed the color of the LED will change to blue Press this button once again and the LED will no longer be blue 6 Hold the ON OFF button on the intelligent remote key for about 1s and the WindRunner will turn off It will be accompanied by a buzz and a light shake just similar to that of stopping engine of a car WindRunner self balancing electric vehicle user s manual 7 Once a
25. e mainframe of WindRunner is balanced forward and backward or not If not the CPU may control the motor on both left and right sides to rotate rapidly and keep the WindRunner balanced The self balancing function allows the driver to stand on the WindRunner with his body inclined forward The mainframe may automatically enable its wheels to move forward and the WindRunner will move forward and vice versa Simply turn the handle left and right Because the balance of WindRunner completely depends on the good functioning of a high speed CPU precision gyro and motor if any one of them has troubles the WindRunner may lose balance The WindRunner has a hot back up dual redundant control system which ensures that all key circuit systems shall be doubled Therefore if any one of the key mod fails to work the backup may be put into operation so as to maximize the safe riding WindRunner self balancing electric vehicle user s manual 1 2 Model of WindRunner G1 series Appearance Type G1U urban standard model GiUR urban for rent model G1X all terrain standard model G1XR all terrain for rent model Features Easy removal of steering handle and suitable for storing into the luggage compartment of most of family owned cars GiU based higher capacity of battery stamina Equipped with external quick charger and optional RFID billing system Low pressure large size all terrain tire s
26. e to avoid death or injury Be calm when getting off the WindRunner Reason being nervousness may cause you to turn the handle Turning the handle while nervous may cause a sudden turn and as a result the rider may become frightened 5 10 Use the power assistant mode Once you take your second foot off the WindRunner shall change from balance mode to power assistant mode or under standby mode tap the foot mat lightly once and a sound of a tick may be heard Then the power assistant mode will be entered At this moment the WindRunner will go forward backward or make a turn according to your shift of the handle But always maintain gentle and low power If you come across a road barrier a flight of step unsafe WindRunner self balancing electric vehicle user s manual or adverse land form etc please use the power assistant mode to pass or go by a roundabout route When you ride up and down a flight of steps under power assistant mode you are strictly forbidden to release the handle under power assistant mode When in power assistant mode please grasp the handle to control the movement of WindRunner It s strictly forbidden to release the handle under power assistant mode If you do the WindRunner may give an alarm sound and shake then change to standby mode which may cause damage in a crash o1 WindRunner self balancing electric vehicle user s manual 5 11 Use t
27. ear If there is no considerable obstacle between you and the WindRunner the intelligent remote key will usually realize the normal ON OFF within a range of 5m If you find the effective distance for power on greatly shortened for example powered on only when the distance from the intelligent remote controller to display panel is less than 50cm or one of your usually used intelligent remote key is unable to power on it means that the battery of this intelligent remote key has been used up Please replace the battery as soon as possible Replacing the battery requires a Phillips screwdriver to unscrew three screws on the back of remote key Correctly place the new battery according to the polarity marks inside Remove the housing of intelligent remote controller as figure below 2 remove the Back cover of 1 Release the Replace the battery of intelligent remote key WindRunner self balancing electric vehicle user s manual 5 How to ride 5 1 Before ride A Suitable riding site should be provided for the first ride This location can be indoors or outside but it should at least be 4x4m 16m2 flat and even Unlike the wet and slippery conditions of the road the site should be smooth No barrier no motor driven vehicles bicycles pets children or other things should distract your attention WindRunner self balancing electric vehicle user s manual To understanding the warnings associated with the WindR
28. elf shall rotate or face up and down while making a turn at site This situation is usually caused by a great change of ambient temperature You can compensate for the change in temperature by taking special steps with the WindRunner intelligent remote key The detailed steps are as followed a First power on After powered on press the lock button on the intelligent remote key The WindRunner will enter lock mode Then press the battery capacity display button four times At this moment the blue LEDs on the display panel shall come in turn from lower to upper A LED shall come on each time you press this b WindRunner self balancing electric vehicle user s manual Once all four LEDs come on the WindRunner will automatically enter into the temperature compensation calculating progress This calculating progress will last for about 3s During this process please ensure that the WindRunner is in absolute rest condition After 3s all blue LEDs will cut off Then the temperature compensation will end You may now continue with the normal riding If there is still a problem after the temperature compensation has ended please repeat the compensation steps mentioned above 4 During normal riding sudden alarms Speed limits and accompanying acute shaking The intelligent safety alarm system may be activated or the internal safety system test may have found hardware trouble including one of the hot back
29. est don t be in a rush to get on WindRunner self balancing electric vehicle user s manual 5 5 Get on 1 To help ease the nervousness of first time riders your instructor may stand face to face with you in front of your WindRunner to help you overcome the swaying due to your first ride Be sure to hold the handle with both hands When standing on the WindRunner keep your eyes straight rather than looking down Put one foot on the foot mat Stand center of gravity and slowly shift your body onto the foot mat and raise the other foot Atthis moment try to avoid the transverse moving of the operating bar Raise the other foot slowly from the ground surface and place it on the foot mat Keep in mind that you are standing on the flat surface of the ground You should believe in the balancing ability of the WindRunner Be calm relax and look straight ahead The sequence of get on posture is shown in the figure below WindRunner self balancing electric vehicle user s manual If you remain relaxed it will be easier to learn how to ride the bike Some people may sway involuntarily during their first ride on the WindRunner Please keep your muscles relax remain balanced and request your instructor to help you hold the handle After a while you will adapt to riding the WindRunner and you will no longer sway 5 6 Move forward and backward 1 Slowly lean forward and feel the advancement
30. f beginner mode Once the WindRunner is started press the Speed limit button on the intelligent remote key After you hear a beep sound the red LED on display panel will turn on as the figure shown WindRunner self balancing electric vehicle user s manual Under beginner mode the last LED on the display panel will steadily glow red 5 4 Prior to get on Stand just behind the WindRunner and hold the handle with either both or a single hand Please align the operating bar basically no force suffered and adjust the handle until the foot mat of WindRunner is basically leveled At this moment five blue LED s shall be shown on the display panel This means that the WindRunner is in the correct ready posture At this point the driver may get on If the operating bar is greatly inclined toward one side or the foot mat of WindRunner is not leveled then five red LED s shall be shown on display panel which means that the WindRunner is in the incorrect ready posture Please get on only after the WindRunner has aligned its posture WindRunner self balancing electric vehicle user s manual Incorrect postures and correct posture at starting If the WindRunner is in an incorrect posture when the driver gets on it may be unable to enter the balance mode and the mainframe may suddenly shake All these may lead to potential hazards and cause the rider to fall If not the WindRunner has not passed the posture t
31. fective protection of the driver Check the charging conditions Avoid long distance riding when the battery capacity is less than 60 Check the basic conditions of WindRunner and make Sure all exposed component parts are not falling damaged and are free of slackness While riding make sure you don t hear any noise or a continuous alarm Before riding ensure that you are in good conditions and clear headed Do not drink or take sedative medicines within 6h s of operating the WindRunner 6 2 Strictly forbidden Itis forbidden to ride in area forbidden by relative country local laws and related authorities It is forbidden to ride at risky places such as deep cave crack steep slope gt 15 and accumulated water gt 6cm deep etc WindRunner self balancing electric vehicle user s manual Itis forbidden to ride in bad weather and road conditions such as heavy freezing rain snow accumulated water wet and slippery surfaces etc WindRunner self balancing electric vehicle user s manual It is forbidden to reverse in high speed and also to make a turn while reversing in high speed It is forbidden to ride the WindRunner up and down a flight of steps and it is also forbidden to raise the WindRunner high into the air such as crossing a ridge in high speed It is also forbidden to transversely cut or ride across a flight of steps Itis forbidden to ride in a motor vehicle
32. ght of the driver the lower the stamina of battery On the contrary the lower the weight of the driver the longer the stamina of the battery WindRunner self balancing electric vehicle user s manual An uphill slope may quickly shorten the stamina of a battery but a downhill slope may prolong the stamina of a battery Under extreme conditions a gentle slope of a continuous several kilometers may charge quite a great amount of the battery capacity Rugged and uneven road surface may shorten the stamina of a battery but a flat and smooth road surface may prolong the stamina of a battery Check the tire pressure of the WindRunner Usually the tire of the WindRunner G1U urban type is 10 20PSI and that of all terrain type G1X 4 8PSI The higher the tire pressure the lower the friction resistance Thus prolong the stamina of battery lower the tire pressure and lessen the stamina of battery but it may be comfortable on a rugged and uneven path Accuracy of battery indication The WindRunner has five LEDs for indicating the battery capacity Though these are a rough means for indicating the capacity of the battery Because the power required for riding the WindRunner varies greatly for example only about 300W required for uniform motion on flat and smooth road surface but accelerate on a steep slope may require 2000W it is difficult to have an accurate indication of the battery capacity The user shal
33. greatly reduce the service life of the new one and the riding performances of WindRunner for safety reasons the performances of WindRunner depend on the worst one of all the batteries WindRunner self balancing electric vehicle user s manual If the shell of battery pack is cracked leaked seriously heated or you smell an abnormal smell immediately stop using of WindRunner remove the battery immediately and contact the UPTECH authorized agent and distributor for solving If the battery leaked you must wear the disposal plastic gloves to protect your skin against injury If you do not obey the battery using instructions hereof the life cycle safety stamina and battery endurance may lead to a loss on the qualification for a battery warranty 7 4 Transport and recycle of the battery pack Chinese laws and regulations only allow the aviation enterprise to transport the lithium ion battery pack not exceed 160Wh capacity so the aviation is not applicable for transporting the battery pack of a WindRunner So you must transport the battery pack by truck or train and firstly consult the transport company For other countries and regions similar with restrictive regulations please contact the local carrier companies for details 8 Routine maintenanc WindRunner self balancing electric vehicle user s manual 8 1 Keep cleanness Please clean your WindRunner immediately after use Periodically clean to keep
34. he lock mode After you have gotten off the WindRunner press the lock button on the intelligent remote key The WindRunner shall enter the lock mode see 4 3 lock modes for details so as to ensure security when you leave the WindRunner temporarily Once the lock mode has started if its posture is changed or touched the whole mainframe of the WindRunner shall shake strongly and give a very short and continuous alarm buzz under the lock mode the WindRunner motor shall be locked up and the tires will be unable to rotate This will make it very difficult to tract the WindRunner The lock mode is usually used for security guarantee when you leave the WindRunner temporarily The best method for ensuring the safety of WindRunner is parking indoor The WindRunner may be put into an elevator easily pass the obstacle free ramp etc When you temporarily put the WindRunner at a public area and leave please try to ensure that you may hear the sound of the alarm and the vehicle is within the view of your sight Then after you get off start the lock mode If you park the WindRunner at an unsafe place or out of your view of sight for long period you better lock up the hub The locks for bikes or motorcycles are also applicable WindRunner self balancing electric vehicle user s manual At any time when you park the WindRunner please keep in mind to take along the intelligent remote key To ensure you do not lose the inte
35. hock absorbance and suitable for rugged and uneven path With stamina slightly lower than that of G1U urban type G1X based high capacity battery and long stamina Equipped with external quick charger and optional RFID billing system the WindRunner may also be upgraded See www WindRunner cn for details WindRunner self balancing electric vehicle user s manual 1 3 Illustration of G1U G1X os SP oy Handle fastener Remote key dock Rubber handle o Operate bar upper Height adjustment screw Height adjustment Operate bar lower Quick release mT G1X fender i Charge port J ee Rt J SS IH A0 Brake light Batt pack Batt pack WindRunner self balancing electric vehicle user s manual 2 Install a new WindRunner 2 1 Check the package content Once unpacked carefully take out the handle and put it aside Then take out the mainframe The mainframe is relatively heavy carefully take it out with the help of another person Take care when picking up the wheel hub with your hands Do not directly pick up the fender Otherwise the fender may be damaged and fingers may be squeezed and harmed WindRunner self balancing electric vehicle user s manual Immediately check whether all things in the package are just the same as shown in table below If not please do not hesitate to contact our sales representative Chassis including tire opera
36. ial number label and code WindRunner self balancing electric vehicle user s manual Each WindRunner has a unique serial number The serial number and warranty card are the only mark for enjoying the free maintenance and repair and after sale service Please verify the consistency of serial numbers at three positions mentioned above If unconformities are found it means that it may not be from an OEM If there is a problem please don t hesitate to contact our sales representatives Please login the official website of WindRunner www windrunner cn click the repair and technical support link located at the lower right part of screen and click the user registration link in a new page Register your warranty card as required you may enjoy the free on line consultation and on line after sale service 2 3 Assembly After you determined that all component parts are complete and intact assemble a new WindRunner according to the following steps WindRunner self balancing electric vehicle user s manual Before handling installing any component parts or making any cleaning and maintenance remember to power off the WindRunner and cut off the charging cable 2 3 1 Tools required and preparations Before assembling a new WindRunner please take out a set of accompanied socket screw wrenches from the packaging All these tools must be kept for future maintenance and transportation You should wear
37. ie cuaisiatsacaticim cated cig ad cis aid ais eideaaatdnaidamaenae eda ada neianaanaiaranemanemterederederananaies 76 WindRunner self balancing electric vehicle user s manual sM OMGNIMG EAE NEE E E A E I N E LEELA ODE e N NEE S Ghee AAD NEO EANA 76 Da FODA eee EEE En 77 T OUDE T aR a E ue ev ee eee eee es ee een ee ee eae aid 78 0 4 FAQS and TrOUDIESHOOUNG tiismcnricrnins ces neNe ANCA ANNE RNR a aaa 78 9 2 Eist Or alarm INormation CodeS annn 80 9 3 Spare parts for repairing and replacing s sssssssnsnssnnnansnnnnennnrnnanansnnnnsnnnnnnannnnnnnnsnnnnenannnnnnansnnnnan 85 9 4 Reporting your troubles s ssssssssssssssssrrrnsnrrrsnrrrsnrrrsnnrrrsnrrrnnnrrnnnrrnnnnrrnnnrruenntrnnnnrnnnnrnnnnrrennnnnnnnnne 85 18 Og Bey e ee NT E E ee E A Cee E E E E T AEA T 86 10 1 WmndRu unner GIU urban YDE ciicccciidccciadidsdidadidadtdidddadidedadadaledidadadsdddidddaddiadadaddledidadadstadadidadddaaaades 86 10 2 WindRunner Gi x all terrain YDE canenrnenncunncoeenennqnunsnnenennenmmanconnrennrenm nn eneantG 87 Appendix A More maintenance instructionS ssssssssssnansunnsensurenannnnunnnsnnnrsnannnnnnnnsnnnnennnrenannnnunansnnnnnnan 88 A 1 Replace the tire oie EEDA E EEE EEE DDE E EEE E EDDA E ETERS DE EEE EEE E SEES EERE EES 88 Pid Replace The T EE eE EEE E EEEE EE EEEE Pie ee Ao eA E A AE AEA EAE E T A T A EAA Aa replace me dear 0 area ete eee cae a Go i ec oo oo ta Appendix B Deep understanding WindRunner B 1 Battery stamina and batte
38. ing electric vehicle user s manual serious accidents such as over turn etc The WindRunner will immediately decelerate The mainframe will shake give an alarm buzz and warn the driver to get off Hot back up power subsystem the WindRunner has a great amount of built in micro electronic devices which require the converter for power supply The micro electronic chip IC has very low failure rate However if partial power fails the system will power off Then all the hot back up design shall lose its significance So two sets of power supplies were provided Any one set may be sufficient for support of the whole system individually If one set of the power supply system fails the system may immediately detect trouble and immediately decelerate The mainframe will shake give an alarm buzz and warn the driver to get off Itshould be noted that the hot back up technology can t give the guarantee of 100 safety For example both gearbox and tire are unable to provide the hot back up The hot back up design may only try to improve the safety of the WindRunner This is neither a guarantee for free troubles such as tire burst nor a guarantee for skidding of tire Strictly obey chapter VI Safe riding instruction for a better guarantee of safety protection B 5 G1X and G1U upgrading mode The WindRunner G1U urban type may be upgraded into G1X all terrain type by replacing the tire and fender assembly by updating
39. istant mode overexert etc speed is too high beyond 6km h handle released and free sliding speed too high the WindRunner shall determine that it is unmanned and this can lead to potential hazards Firstly it shall give a vibration audio alarm automatically cut off the power output and enter the standby mode Just then if the operating bar is not held the WindRunner shall lose its balance e If the inclined angle of the WindRunner under balance mode is too high overexert etc at t moment of acceleration and deceleration overload e g riding on a sharp slope i WindRunner self balancing electric vehicle user s manual circuit overheated or battery capacity fully used up etc the WindRunner shall firstly give a vibration and then buzz alarm 4 5s If the driver has not gotten off or reduced his her speed and load within 4 5s the WindRunner will enter standby mode and the rider may fall off 3 2 Power assistant mode The power assistant mode means that the WindRunner has been started and the driver has not gotten on but the movement by tracting the operating bar Under the power assistant mode the WindRunner shall output its power about 30 and move slowly This operating mode is suitable for handling or shifting the WindRunner See 5 11 for details The WindRunner shall be in the power assistant mode under the following situations After powered on and foot mat basically leveled tap any one foot mat lightl
40. l 7 2 Charging After received a new WindRunner and the first test is complete please charge the battery of WindRunner as soon as possible The charging shall be done at a dry static free place The precautions for charging are as followings 1 Open the rubber cap on the charging outlet 2 Make sure the charging outlet is dry 3 Insert one end of charging cable into the earthling AC socket 100V 240V 50Hz or 60Hz And the other end of charging cable shall be inserted into the charging outlet of WindRunner Open the rubber cap on the charging outlet insert the charging cable WindRunner self balancing electric vehicle user s manual The upper part of rubber cap of charging outlet is fixed so open it from its lower part Please do not plug in charge wire if the charging port is exposed to moisture or visibly damaged Otherwise you may suffer from electric shock and may experience serious injury or even death Ti The LEDs at the lowest part of display panel comes on in red and regularly flickers which means that the charging is in process At the moment of charging you may hear the light noise of fan in the WindRunner In charging red LED flicker charging completed blue LED glow steadily 2 The blue LEDs on display panel glow steadily which means that the charging is complete Once the charging is complete you may pull out the charging cable and seal the charging WindRunner se
41. l fault for example one battery power failure and one set of balancing unit failed it shall immediately trigger the intelligent safety alarm If just ride the WindRunner immediately get off and do not hesitate to contact the authorized after sale service agent to repair If the intelligent safety alarm is activated once powered on it may be caused by insufficient battery voltage Please charge it Once charged if it still gives an alarm please consult the chapter IX to solve the troubles o contact the factory for repair WindRunner self balancing electric vehicle user s manual 7 Charging and battery maintenance 7 1 Introduction of battery Both sets of lithium batteries for WindRunner are mutually on standby They are located at a place under the chassis The basic data of battery pack are shown in table below Type of battery Rated capacity each Applicable model of WindRunner Weight each Range of storage temperature Range of working charging temperature Duration for fully charged Typical cycle life Safety Lithium Ferrous Phosphate battery pack 76 8VDC 5 6Ah 430Wh G1U G1X 5 1 Kg 20 C 50 C 15 C 45 C 2 4h with the built in charger gt 1000 times for charging and discharging converted into riding mileage about 30000km No fire and no explosion if put into flame short circuit or pierced Built in protection circuit WindRunner self balancing electric vehicle user s manua
42. l try to avoid acute acceleration with battery capacity less than 40 or moving on a complicated land form Try to avoid moving uphill for long periods at a time WindRunner self balancing electric vehicle user s manual The properties of a battery may vary gradually with frequent use So the battery indication may be inaccurate after a period of time To ensure high safety the battery capacity of WindRunner has a redundant safety margin When the battery indication has only one division the WindRunner begins its Speed limit and shake alarm The battery is actually 10 30 left For safety reasons also keep an eye out for battery discharge If you do all of these things the life cycle of the battery may be prolonged B 2 Tire and land form The tire pattern and land form have an adaptability and compatibility relationship Moreover the performances of the tire used for suitable or unsuitable land forms vary greatly The tire of the WindRunner G1U urban type is suitable for common urban road conditions such as asphalt road cement road glazed tile and brick road rigid leveled earthy roads etc Under these service conditions G1U urban type may award the best riding experiences and optimum tire adherence effect and optimum battery stamina But the all terrain type is lower efficiency on urban road so the battery stamina is relatively lower and the tire may be worn more rapidly The pattern of tire for the WindRunner G
43. lane In some countries and regions the non motor vehicle lane is also forbidden to ride this type of vehicle Please refer to the local laws and regulations While riding it is strictly forbidden to remove both hands from the operating bar It is forbidden to allow a child less than 14 year old to ride the WindRunner WindRunner self balancing electric vehicle user s manual It is forbidden to make a phone call or check the capacity of battery etc while riding It is forbidden for two or more people to stand or ride on the WindRunner It is forbidden for a pregnant woman excessively drunk mental patient person with heart disease or a disabled person to ride the WindRunner It is forbidden to ride in unsafe conditions such as places endangered by fire or explosion flammable gas steam liquid dust and fiber etc It is forbidden to violate other requirements of this manual especially those items strictly forbidden such as warning and caution 6 3 Driving manners safe riding While riding the WindRunner please study and obey the local laws and regulations on transportation Please ride carefully to avoid any collisions To ensure a controllable situation please ride at a safe speed for both the driver himself herself and others Be ready to stop any accidents arise Have a high regard for pedestrians right for road using Avoid any shocks to pedestrians especially children When passing
44. lf balancing electric vehicle user s manual outlet cap tightly Otherwise the moisture in rainy days or damp weather may enter inside the WindRunner and cause damages to the inside precision circuits The built in charger of WindRunner has the auto protection function You may charge the WindRunner at any time No damages to battery for long charging period 7 3 battery maintenance The battery pack is the source of energy for WindRunner and also one of the WindRunner system components that can easily be damaged The battery pack has high value and is very important for safe running So this part shall describe the basic knowledge for battery maintenance For identical battery packs whether their maintenance is correct or not their life cycle and reliability are quite different A well maintained battery pack may last for more than 2000 charge cycles and still keep 80 of its capacity but a poorly maintained battery pack may only last for 100 charge cycles and then approximately rejected Please try to obey all the key points for battery maintenance below to prolong the service life of the battery pack to save the cost and reduce the environment impact of rejected battery p Do not directly give up the rejected battery pack As a way to avoid environmental pol WindRunner self balancing electric vehicle user s manual please contact the agent and distributor authorized by UPTECH or UPTECH we provide battery
45. ll the above mentioned steps are fulfilled the WindRunner has passed the basic test Please continue to read chapter 3 4 of this manual then follow Chapter V step by step to get on and do a test ride At the moment of the test ride please don t be eager to get on Incorrect transportation or storage may cause the new WindRunner not function properly Getting on and riding are before the test has finished is unsafe The testing speed should be slower During the test it s forbidden to release the handle During the test ride if you find any abnormalities especially a regular tick tick alarm buzz or a red flicker on the LED display panel it usually means that the product is not in good condition Please refer to chapter 9 of this manual or contact your seller for repair WindRunner self balancing electric vehicle user s manual 3 Operating modes The WindRunner has been provided with different operating modes good understanding and using may be helpful for your better riding 3 1Standby mode The standby mode means that the WindRunner has been started but doesn t have any movement or balancing ability The WindRunner shall be in standby mode under the following situations After powered on the WindRunner shall be in standby mode If no any other operations happen within 10 minutes the WindRunner will automatically powered off If the WindRunner is tilted too high under power ass
46. lligent remote key place it together with the WindRunner to avoid any loss WindRunner self balancing electric vehicle user s manual 6 Safe riding instructions This part is very important please read carefully understand and strictly obey Our company will not take any responsibility for loss in property and personal injury caused by violation of safety riding instructions The WindRunner is a sports and entertainment tool so it also accompanies the safety risks similar to all those sports and entertainment activities Ride strictly in accordance with the safe riding instructions This may maximize the safety of you and other persons even if the WindRunner has serious irreversible troubles this will ensure no serious injury to you However you should understand once you ride the WindRunner on a road or public place even if you completely obey the safe riding instructions you shall also be faced with risks from other people or means of transportation So while riding maintaining an appropriate level of vigilance and reasonable distance from other people and means of transportation are very important 6 1 You must strictly obey Understand and obey the local laws and regulations and only ride at appropriate places WindRunner self balancing electric vehicle user s manual Before riding wear a safety helmet and harness for knees elbows and wrists All the above are necessary for the ef
47. loose please check the corresponding screws and retighten with the accompanied tools 8 2 Check the inflation pressure of tire In general the pressure of the tire of the WindRunner G1U urban type is kept at 10 20PSI a the maximum up to 30PSI and that of all terrain type G1X shall be kept at 4 8PSI the WindRunner self balancing electric vehicle user s manual maximum up to 12PSI Higher pressure of the tire may reduce its friction resistance thus increase the battery stamina Lower inflation pressure of the tire may reduce the battery stamina but relatively comfortable on the rugged and uneven road The pressure of a tire too high or too low may speed up the wearing of the tire 8 3 Storage Please store indoor dry and normal temperature Try to control the storage temperature at 0 C 30 the room temperature storage is favorable for prolonging the service life of battery and other component parts 8 4 handling Please handle the WindRunner appropriately and obey the steps as followed Ensure the WindRunner is not connected to the charging cable and is powered off If you want to put the WindRunner into a narrow and small space such as the luggage compartment of car etc please firstly loosen the quick release handle of WindRunner operating bar remove the whole operating bar and respectively handle the mainframe and operating bar WindRunner self balancing electric vehicle user s m
48. may be applicable for riding WindRunner Under the Speed limit mode press the Speed limit button on the intelligent remote key You may hear a very short buzz or tick and the blue LED at the lowest part of display panel will cut off This means that the normal mode is entered Under this normal mode the WindRunner has the maximum speed and highest sensitivity Press the Speed limit of intelligent remote key to toggle between beginner mode Speed limit mode and normal mode WindRunner self balancing electric vehicle user s manual The built in intelligent system of WindRunner shall try to ensure the driver s safety However it cannot ensure to solve problems associated with long overload overheating battery capacity wheel skidding etc Under balance mode the WindRunner may begin to shake and alarm which is called the intelligent safety alarm if the driver pays no attention within a few seconds it may be changed to standby mode and cut off the power output Just then if the driver is still on the WindRunner the driver may be seriously injured or fall 3 4 Lock mode The lock mode is a security function of WindRunner under the power on state for temporary short parking to protect it against traction by others Under the power on state press lock on the intelligent remote key to enter the lock mode After locked up press ON OFF to unlock All above mentioned working modes
49. nce powered on again Internal fault alarm note LED close to LOGO is red and flickers red red blue blue red flicker red blue blue blue red flicker An Internal fault alarm it is usually non self recoverable and may require maintenance A hint at wrong internal communication usually caused by loose internal cable or trouble of component parts Please do not continue riding Contact the factory for inspection An Internal fault alarm May hint at a built in charger malfunction incorrect output or circuit failure in battery interface Please contact the factory for inspection An Internal fault alarm A hint at motor riding circuit failure Usually accompanied with a single side wheel lock up or both wheels simultaneously locking 83 WindRunner self balancing electric vehicle user s manual red blue blue red red flicker red blue red blue red flicker blue blue blue blue red flicker all 5 LEDs are red flicker 84 etc If the wheel locks up the user shall remove both batteries and then tract to prevent further damages Please contact the factory for inspection An Internal fault alarm A hint at failure in one of both motor sensor sets Immediately stop riding and please contact the factory for inspection An Internal fault alarm A hint that one of both hot back up posture detection units failed Do not continue riding Ple
50. oO J WINDFeUNNER Self balancing electric vehicle USER MANUAL UPTECH Robotics WindRunner self balancing electric vehicle user s manual 4 WARNING Just the same as any other means of transportation when you ride the WindRunner you may lose control fall and become seriously injured in a crash Therefore please carefully read this manual and got experienced With safe riding skills you may reduce or avoid any hazards and risks The figure on the left shows some unsafe riding situations For example the wet and Slippery surface of the road may cause your WindRunner to skid around and fall Carefully read this manual to avoid any hazards and risks For a further understanding of potential hazards and safe riding skills login to our official website http www windrunner cn en for a safe riding instruction video This manual will explain all of the operating instructions and precautions associated with using the WindRunner to you You must carefully read and obey this manual Beijing UPTECH Robotics Technology Co Ltd shall never be liable for any consequences incurred on account of improper and wrong operations Please buy or rent the WindRunner from distributors authorized by UPTECH Robotics If not you may suffer the loss of our warranty and after sale service You may consult the local dealer listed on our official website WindRunner self balancing electric
51. of the WindRunner Then lean back feel the deceleration and stop Control its speed Repeat several times to ensure control of the movement of the WindRunner and also the placement of your body at the center of gravity WindRunner self balancing electric vehicle user s manual go backward balancing go forward avoid any swaying For a new rider make sure you remain relaxed and ride the WindRunner gently The more relax you remain the less swaying you will experience Avoid swaying or any sudden shift of your body as the center of gravity This will help you to avoid sudden skidding or falling 2 Turn your head around to look and let your body slowly lean backward to reverse the WindRunner Then reset You may feel the deceleration and stop of the WindRunner Repeat several times Avoid collisions and you will avoid falling WindRunner self balancing electric vehicle user s manual Reverse riding is not a normal riding mode There is no substitution for advancing unless the rider has to move backwards to reverse Otherwise please not reverse riding You may reverse by turn back then ride forward If the reverse speed is too high the WindRunner will shake and give the buzz alarm 5 7 Decelerate and stop Shift the center of gravity of the driver s weight opposite of the direction of moving to decelerate and stop the WindRunner Follow the methods as followed 1 When you go forwar
52. ons it is unsafe to continue riding WindRunner self balancing electric vehicle user s manual If the ambient temperature is detected to be to low lt 10 C or too high gt 40 C at the moment the WindRunner is powered on the intelligent Speed limit of the WindRunner shall also function Just then even if the battery capacity is full the maximum speed may be unable to reach To ensure high safety the detailed Speed limit depends on the WindRunner s internal intelligent Speed limit algorithm B 4 Hot back up safety mechanism Several key components of the WindRunner have the hot back up safety mechanism to maximize the guarantee of the driver s safety Hot back up battery pack both battery packs are used together one for operating and one for standby If one battery pack fails powers off or disengaged it may not cause accidents Reason being the WindRunner may immediately detect the exceptions of the battery pack and decelerate immediately The shaking mainframe will give the alarm buzz and warn the driver to get off Hot back up posture sensor unit the posture sensor unit is the core of the WindRunner If the posture sensor unit fails and does not work while riding a serious accident may be possibly happen To ensure safety two sets of individual posture sensor units are provided Through a unique control algorithm if any one sets out of function the system may av WindRunner self balanc
53. rating bar ssssssssssrnnensnrnnannnsunnnsnnnnenannnnannnsunnnennnrenannnsunnnsnnunenannnnuanansunnnan 18 2 A Inteligent remote Key Serierna aiaa A a ae Ea aP a e a a E a Aea aa n An bE E NEAN 20 2 4 1 Function ISU ccccasceccedetusnsecscatesadecatecadsccdenatncecicadseedetadeoudscadanneieeddcasscceesateendecadeuaencecesadsuccusaewes 21 mane Hie E EEEE Wie ee Sie E EENE EEE OPERE E E Re Neen iene ie ENEE E EErEE E ee Se ee ewe Wee ee eee EEE E EEEE E EE EER 22 O TEPEEEET PETTITTE ETETETT TETTIE ETETETT TIETEET TTET ETTET TETIT ATT TET ETETETT 25 WindRunner self balancing electric vehicle user s manual Bae POW Er asslolall E wcserteupteceties see E A A E TE N E E E en E N OEE NEN 26 Bo BN EMOCE e EEE E EEEE EE 27 321 Beginner mode 5KM a MaX testes ie sta sea aces iene as eee ee san ne ele en dn eee eee 28 35252 Speed imit mode LOK MaX scanicineisisaiiawscaincnannawinaiesgnananndaaaaniienseerinnannaniiaiasaneeiennanadananeeeeds 28 32225 N rmal MOde 20kmi h MAX escssssccssareccsnsarecetecsvecerenisererscnvereeeredaestecetesadecssncateceseussacerseiseereetees 29 DP MOCK IMOUG aiuiccateuininst ct uustes pie iaue E butaneeoutataeesee senate uuiauase 30 Use the intelligent remote keyS cccec ccc cc cece c erence ene e eee nnn S SEE EER RSE EEE RASS OSE E EERE SO OSE ES aR SooSE EER RaoEEES 31 A ONS OFF aces tebe ve ese be ee beck Veet we ee betes bees deus beeen teks te Gets berets E E deus teusteeebeeeeeets 31 oe MOda SWIC Mircita
54. red red blue Acker after charged it may be caused by battery trouble Please contact the factory for repair S41 WindRunner self balancing electric vehicle user s manual red red blue red blue flicker red red red blue blue flicker red red blue blue blue flicker An intelligent safety alarm it is self recoverable after troubles are solved A hint of internal temperature too high Usually arises at air temperature gt 30 C continuous running or direct exposure under sunlight Cut off the machine and put in a cool place Continue riding only after the temperature of machine has reduced to a safe range An intelligent safety alarm it is self recoverable after troubles are solved A alarm of overload Usually caused by several reasons wheels blocked rest on slope for long period the rider weight too high etc The driver shall decelerate immediately get off and wait Continue riding only after troubles have been solved An intelligent safety alarm it is self recoverable after troubles have been solved A hint that mainframe inclined angle too high during riding This alarm is usually triggered by an unbalanced mainframe a fallen under tire skid or a very acute acceleration and deceleration Once this alarm arises the WindRunner shall automatically enter the WindRunner self balancing electric vehicle user s manual standby mode after alarmed for 5s It will recover o
55. right to master this skill Turn right at site turn left at site make a turn in moving 2 Makeaturnin moving After you have become familiarized with the go forward go backward and turn at site try to advance slowly and make a turn Keep your knees slightly bent and incline to the direction you want to make a turn The angle shall be consistent with that of the operating bar Repeat until you master this skill WindRunner self balancing electric vehicle user s manual No matter at site or moving making a sharp turn is very dangerous It can easily cause you to lose balance and fall So please decelerate and ride slowly at the moment of making a turn 5 9 Get off When you want to get off from the WindRunner for the first time please request your instructor to help you by holding the handle of WindRunner Make sure your body is steady and the center of gravity Then without swaying carefully get off WindRunner self balancing electric vehicle user s manual Please request your instructor for a help one foot a time After you get off hold the operating bar steady The detailed getting off methods are as followed 1 Firmly hold the operating bar with both hands get off one foot a time from the foot mat and avoid shifting backward or left right 2 After you have completely gotten off the WindRunner should be powered off The WindRunner may advance forward so both hands should remain on the handl
56. rmal mode so its response should be more sluggish This mode is suitable for the new or unskillful riders After its speed is beyond 5m h the WindRunner shall be faced upward pushing the driver backward to forcibly decelerate Display panel under Speed limit mode Both beginner mode and Speed limit mode shall be saved even if powered off After next startup it may automatically enter the working mode before the last power off WindRunner self balancing electric vehicle user s manual Under beginner mode press the Speed limit of intelligent remote key to change into Speed limit mode the last LED on display panel shall be blue and glowing steadily You will also hear an accompanying warning buzz At this moment if the rider stands on the WindRunner the system shall work under Speed limit mode Under this mode the maximum design speed of WindRunner is limited to 10km h suitable for complicated road conditions for example pedestrian too much or uneven surface of road After its speed is beyond 10km h the WindRunner shall be faced upward pushing the driver backward to forcibly decelerate Display panel under Speed limit mode Under Speed limit mode press the Speed limit of intelligent remote key to change to normal mode Just then if you stand onto the WindRunner the system shall work under normal mode The maximum design speed of WindRunner will be restricted to 20km h for easy operation Thi
57. ry indication Factors airecting the Dattery StaIMING sictuscceccrinvacineeecuisceconednsntocatovadon eieaudencseuouancetocationadecetavaduedaiouasue PCCUacy Cr Daltery MGI GACIO WW ween esesec ever wvsete gees EEE TEE Boz Tenna land fOr eE EE EEEE EEEE EESE EEEE TEE EEEE EEE EEE E Pea ADOUCIR n PE o N era WindRunner self balancing electric vehicle user s manual Ba HOt DaCk Up Salely MeCChanISiNiuscrssestrevicesouneiversbarsaueseenieenbesnieuenberteunsiueseenieunieebieeesresteaeniustearieussls 97 Bo and GL UpGiraGgiiG INO Ge EE EEEE EEE EEEE E TEE 98 Bes ee NONE atin area caren eee eae nee ee ee ee ee ee eee eee 99 Appendix C Outline and GIMENSIONS sperringene 100 c LuDa model Gi reer r ree ern rere Tren Te tere Tre Teer ener Terre nr rere T cnr er ee Tren tr Tn 100 SEEE r ae e eE Gt E EE AEE A S A E E E E E 101 CONAC IS eee EE EEEE E EEEE 102 WindRunner self balancing electric vehicle user s manual 1 Introduction of WindRunner 1 1 How do a WindRunner work The WindRunner is a dual wheel self balanceable electrically operated vehicle a revolutionary ride instead of walk and recreational tool The driver may operate the movement of WindRunner by standing on it and shifting his her body The WindRunner itself may automatically keep balance and the driver does not have to worry about the risk of falling With the built in electronic gyro the on board high speed CPU may calculate in 200 times s whether th
58. s mode is Suitable for skillful drivers and good road conditions e g no pedestrian and road surface flat and even After its speed is beyond 20km h the WindRunner shall change its posture and push the driver backward to forcibly restrict the speed WindRunner self balancing electric vehicle user s manual Display panel under normal mode 4 3 Lock mode This mode is effective only after the WindRunner is started and under standby or power assistant mode note for safety reasons it is unable to enter the lock mode under balance mode Under standby mode or power assistant mode press lock on the intelligent remote key to activate the lock mode If touched or handled by external force its posture will change and the whole mainframe of WindRunner shall strongly shake give the alarm buzz the tires will lock up and will be difficult to tract If the WindRunner is under this working mode for more than 12h or if the battery capacity is approximately used up the system shall be powered off automatically WindRunner self balancing electric vehicle user s manual Press the lock key and the red LED on the display panel will light up All other LED lights will turn off This will be accompanied by a very short sound or tick which indicates that the WindRunner has entered lock mode 4 4 Battery indication Once powered on press and hold battery indication and the LED on the displ
59. s manual Please pay close attention to the following marks and meanings Carefully read and understand them well PSS OEE Woe improper use and or improper operation may operation can cause cause malfunction or Helps you to rider better serious loss of property heavy damage to your and easier or heavy injury death WindRunner WindRunner self balancing electric vehicle user s manual Contents CAUTION OF FISKS arccos ir EAEE EEEE MRR RAKES K HK OE R 1 Trademark registration and legal NnoticeS s sssssunsssnsnrnenannnnnnansnnnnnnannnnnnnnsnnnnennarsnannnnnnnnsnnnnenannnnnnannnnnnan 3 About this manual oo EERE EEE E TEED EEE EERE EEE EE EEE DEES SEER EDD E EE EES DESH EERE EES 4 tean odU OOE VWINGRUNME EEEE EEE E EEE TEE EE EEE 11 1t HOw do a WINdRURNEF WORK sssisccaceransuwarwasduwanacnanseresananenniennierenarmanieteseaniaenaaniuaresarnanienecenanenenee 11 1 2 Mod l or WnaRunner G1 Seres tcc une od ne ne since A 12 Eeo Ma r O OF aU OT a a ai aa 13 2 Install a new WINGRUNNET cece ccc EEE EDDA ERED DEAE ERED EEE EEE DESH EEE EEE EEE EES 14 Zw Check the package Content cr cuacedouatnautiocalnsacin a a a e a a aa aaa AEAEE 14 Dp E CaN ETITI eee eee eee ee eee eee ee ee ee eee 16 OG ANS SE 10 41 0 LY neeyaenenee ee TENT ea en ne nm nee ner re eT 17 2 5 1 Tools required and Preparation sciciisiisssciessdsssseceisssdacaveirisiadeaniecadaneissedecadarstedadwanieeaiannivesdeawens 18 2 3 2 Assemble the ope
60. tc the intelligent safety alarm may be triggered just then the foot mat shall tilt backward considerably and warn the driver to get off At this moment the driver shall get off and hold the handle to move into power assistant mode Otherwise the WindRunner will enter into standby mode after 5s and the driver may be fall off if he she still stands on it Low battery When the battery capacity is too low usually lower than 10 the battery capacity the intelligent safety alarm shall be triggered At this moment immediately get off and charge it as soon as possible If the driver continues to move the foot mat of the WindRunner shall be faced up which may push the driver to get off Reverse speed too high riding on a steep slope or staying on a ramp too long battery capacity too low WindRunner self balancing electric vehicle user s manual Power assistant mode Under power assistant mode if the driver is not holding firmly to the handle the WindRunner itself shall advance a section of distance and then trigger the intelligent safety alarm After alarmed if its speed is not reduced it shall enter the standby mode after a few seconds It is forbidden to let the WindRunner itself move under power assistant mode Ensure that the operating bar of the WindRunner is under your control It is strictly forbidden to release the handle under power assistant mode Internal faults When the WindRunner detects an Interna
61. the control program firmware The G1X all terrain type WindRunner self balancing electric vehicle user s manual may also be upgraded into G1U urban type In the future the UPTECH shall provide the upgrading service through the authorized agent distributor step by step Please do not hesitate to contact UPTECH B 6 Brake lights All WindRunner s are equipped with standard LED brake lights Under dark conditions the red and eye catching brake lights may greatly reduce the possibility of rear end collision The brake lights are unable to be controlled by the user Only by the built in intelligent algorithm The brake lights shall come on at the moment of decelerating or downhill journey The driver may ignore when the brake lights come on WindRunner self balancing electric vehicle user s manual Appendix C Outline and dimensions C 1 urban model GiU PE I iain tit A N X z 3 S t 7 T si g n Ta amm e hanme I DAA AAAT WindRunner self balancing electric vehicle C 2 all terrain model G1X ee CONALL L user s manual WindRunner self balancing electric vehicle user s manual Contact us If you find any problems while riding the WindRunner maintenance repair and safety etc consult your manufacturer about the troubles You may contact us as at the following address and number We hope to provide good service to you
62. ting bar quick release 1 set Care to distinguish the all terrain type and urban type battery pack 2 sets including one charging cable Lower and upper segment of operating bar handle 1 set decorative cap Intelligent remote key 2 pcs Two general purpose intelligent remote keys One operating and one standby Battery of intelligent remote key 2 pcs Backup battery for intelligent remote key Dismantling tools and working gloves 1 set socket screw wrench 1 set working gloves 1 pair instruction manual and safety riding instruction DVD 1 set warranty card WindRunner self balancing electric vehicle user s manual 2 2 Check the S N All warranty terms are located on the warranty card and are guaranteed in three aspects repair spare parts and contact method All shall be signed by your seller upon the entry into effect date of warranty contact method of the seller and stamp Moreover the last page of the warranty card should have been attached with the label of serial number The serial number is the combination of 12 bit character and number You may find the serial number located on the positions below Attached at the last page of warranty card Attached at the place under the right foot mat Outside of packing G1U Urban model G1X Offroad model G1 U1 2020001 2A sa tists Rvar PIND RUNNER 0 Produc 02 Week of manufacture UPTECH ROBOTICS number www windrunner cn meanings of ser
63. tric vehicle user s manual 6 Check whether the O ring is in good conditions or not Put the O ring onto the oil hole sealing bolt and tighten it Apart from the battery pack tire fender foot mat gear oil and operating bar all other parts of mainframe can t be maintained or repaired by the user It is strictly forbidden to loosen or remove the chassis cover plate screws or any other parts without authorization Otherwise it may cause poor waterproof performances serious damage or accidents WindRunner self balancing electric vehicle user s manual Appendix B Deep understanding WindRunner B 1 Battery stamina and battery indication Factors affecting the battery stamina For the same set of batteries under different service conditions after charged its stamina may be quite different The followings are some factors affecting the stamina Try to ride under uniform speed 12 18km h to prolong the stamina of the battery once charged Frequently accelerate and decelerate Low speed riding and maximum speed riding may shorten the stamina of the battery once charged Riding at 10 C 30 C may get the maximum stamina for the chemical properties of the lithium battery Riding under low temperature or high temperature may decrease the optimum stamina The nominal mileage of the WindRunner battery is determined under the carrying capacity of 70kg including the driver and luggage The higher the wei
64. unner you may require an instructor coach to help read this manual and view the safety video This will help you when riding the WindRunner Wear the safety helmet and harness to protect yourself against injuries Move the WindRunner to the center of a site Adjust the operating bar to your comfortable height See figure below for the method of adjusting the operating bar Some types may replace the screw with large size box spanner and then you may adjust directly with hands No tools will be required Loose the hand op screw and adjust handbar height Operate bar fasten spacer Hand op screw CW tighten ON or hex screw CCW loose WindRunner self balancing electric vehicle user s manual Learn and correctly use all functions of intelligent remote key 5 2 Starting the WindRunner Press ON OFF on the intelligent remote key to start the WindRunner you may hear the buzz once the WindRunner is powered on several LED lights may come on in turn and the large blue LED at the highest part of display panel shall glow steadily Once this happens the WindRunner has successfully powered on At the moment the WindRunner is of powered on please keep the WindRunner foot mat basically leveled When you first touch the WindRunner wait to get on A new rider may need only 2 3 minutes for training Obey the following steps effectively ensure your safety 5 3 Verify the startup o
65. up systems failed This is usually caused by too high temperature a heavy load unsafe riding methods or hardware failure detected while riding the WindRunner Please consult 9 2 trouble code lists for details of troubles If unable to solve by yourself please contact the local agent distributor for repair 9 2 List of alarm information codes WindRunner self balancing electric vehicle user s manual If any troubles arise or intelligent safety alarm is activated the lamps on WindRunner shall continuously flicker This will be accompanied with alarm sound and an acute shake in the mainframe While riding if any troubles arise or intelligent safety alarm is activated the WindRunner will forcibly decelerate and you will experience an acute shake in the mainframe Warn the driver to get off If it is an irreversible trouble the WindRunner shall power off automatically if alarm goes off for 20s Preliminarily determine the causes of trouble or alarm according to the flicker of LED at the moment of alarming for solving the troubles The followings are the common alarm trouble and corresponding LED conditions intelligent safety alarm note LED close to LOGO is blue and flicker e An intelligent safety alarm it is self recoverable after troubles are solved A hint of battery capacity seriously insufficient e You should charge the battery as soon as possible If the trouble still exists red red
66. vewsvsvewwrewssevewvenssevcweewavswewereeusevewvenvswenwvewseswvwwrewesevewwenuseewerewsunevaens 58 pF ACTIVE protectio INSU UCHO esrriririnirenEri riru rererere EE EErEE EE ENE E E E E E E E E E E EErEE ERE EE EErEE EEEE 60 6 5 Intelligent safe alarim Protection iiciccccitdsisdscidadidatedadidadedacddadsdedidadiditddadidadedadddadddedddadidatddadidadedadaaams 62 7 Charging and Dattery Mantena manencccnncnencncnnannrancuccarennuucncnenn EEE TEE 66 Zel MiroducHhon Of DATST ctiiisocriranianrriarimriensemescediernumiiindaneiemremasendieniamdirennersiraebamcendinnaconasiunaant 66 7 2 CWANGING cscrcvaicaneeeranncatenssencaananeucesacanmarees A A A A aa a 67 P e ea Don Ee Ela e E E E E TEE E IE E IE TT 69 7 3 1 Assembly disassembly the battery pack s sassssussnsnsnnnenanrnnsunansunnnennnrenannnnunnnsnnurenannnnanansnnnnan 70 7 3 2 Improve the cycle life of the battery DaCK irincicscncnncncecnannenminndnnnaeaeenuie AE A EAA AAAA 70 74 lransport and recycle Of the Dattery pagk cititsimuiciormioicinieroioiiamiienieideeieioinieaariionmeiehoanniond 73 Se FOULING NEN T E E E CRC emnCene 73 Bak Se DC lOO E E E E E usscecoloruulmrotouauncitecatenaceonueded 74 8 2 Check whether the screw is lOOSE 0r OU vevevecevevwveseveneensueweneeweverevavuvusewanevnsueeeavvasuaedseriveseeeceueededvaes 75 82 Check the intlavion pressure OF UilGcisssccrcrcersrenersrsseces en E in N SNE E EEEN EEEE Ei 75 SON UG Si ssasicssscssicisscisicisicisicisicas cas cisicid ais eis cut
67. y has enough battery capacity but is still unable to power on then it may be caused by the power of the WindRunner battery being fully used up It may also refer to an internal circuit failure Please retest only after the WindRunner is fully charged If still unable to power on after it has been fully charged refer to 7 2 of this manual please contact the local agent distributor for repair During normal riding if the WindRunner is unable to power on after automatically being powered off or if there is a high resistance felt during traction of WindRunner then it is probably caused by internal motor riding circuit failure To prevent short circuiting of the WindRunner self balancing electric vehicle user s manual battery the user should remove both batteries as soon as possible Do not hesitate to contact the factory for repair 2 After powered on alarm or red LED continuously flickered If able to power on but you hear the alarm only after powered on this means that the WindRunner has not passed the power on self test power on self test The detailed trouble information is related to LED state so please consult the 9 2 alarm information code list to verify the problem and solving method For troubles you are unable to solve by yourself please contact the local agent distributor for repair 3 Once powered on normally and after the driver gets on if there is no turning of the handle the WindRunner its
68. y with your foot You may hear a very short buzz and then the wheels of WindRunner will begin to move and enter the power assistant mode After riding take your foot off the foot mat You may hear a very short buzz and then the WindRunner will change from balance mode to power assistant mode WindRunner self balancing electric vehicle user s manual If required to enter the power assistant mode under powered on only tap the foot mat once lightly with your foot If not on do not push on the foot mat always with heavy thing or foot This may enable the WindRunner wrongly deem that you have got on and thus the WindRunner will enter balance mode which may be very possible to cause a loss of control and eventually lead to serious damage or hurt 3 3 Balance mode Once you stand on the WindRunner the WindRunner will begin working and enter balance mode Balance mode is convenient for operating and riding on different road conditions The balance mode consists of beginner mode Speed limit mode and normal mode The WindRunner has four foot on mat sensors to detect whether the driver has got on All four sensors have the same function once the WindRunner sensors that anyone is on it will detect that the WindRunner is manned It may enter balance mode For all four sensors arranged on both sides even if the driver rose one foot during riding it may give no influences to the test WindRunner self balancing ele

USER MANUAL - Carts & Wheels

Contents

Download Pdf Manuals

Related Search

Related Contents

USER MANUAL - Carts &amp; Wheels

Contents

Download Pdf Manuals

Related Search

Related Contents

USER MANUAL - Carts & Wheels