User Manual of QUICRUN Series Sensored Brushless
Contents
1. circuits If that really happens please turn off the device immediately and then clear and blow dry it carefully 5 Please read through manuals of each power equipment like ESC motor battery etc and chassis to ensure the power system configuration is rational before the use as the incorrect power system configuration may result in overload and eventually damage the equipments 6 Prohibit the full throttle operation before the pinion installation Under non loaded circumstances over high RPM may cause damage to the motor 7 Make sure all the parts are well connected as misconnection or poor connection may lead to abnormal control damage or other unpredictable problems 8 Never let the temperature of the motor can shell exceeds 90 C 194F otherwise the motor will be damaged and or the rotor will be demagnetized Installation amp Connection 1 To Install the Motor 1 Screws used for installation are 3mm in diameter amp 5mm in length Before mounting the motor onto the vehicle please ensure that all the screws are applicable to avoid damaging the motor In general it s ok to adopt screws which are 3 mm in diameter and less than 8mm in length the specific length is up to the chassis size 2 Install the golden connectors here it adopts the brand new method to fasten male amp female connectors by screws Please check Figure 1 for reference 2 To Connect the Motor 1 Three power wires need to be connected to the motor and2. maximum input power nor the rated power The calculation formula used here is RPM x Torque 9550 2 The value of the maximum output power is always lower than the value of the input power Therefore its meaningless to compare the maximum output power mentioned in the form above with the input power of motors of other brands Besides values in the form above may differ from the test data of other factories because of different test benches 3 The input current at the point of the maximum output power is useful for the load configuration and the ESC selection here we strongly suggest users not make the load quota bigger than the maximum output power point that means please don t make the input current larger than the current at the maximum output power point 4 As the power of 10 5T 13 5T 17 5T amp 21 5T motor is not big so they are not applicable for 4WD Monster trucks and other high weight and heavy load vehicles or games need very great power If forcibly use them in those conditions perhaps they will get burnt Hereby we suggest users choose the 4 pole motor with great power like QUICRUN 3656 KV 3800 when high power is needed Gear Selection IMPORTANT It is very important to select the reasonable gear ratio as inappropriate selection may cause great loss to users Please select the correct gear ratio according to the following points 1 Operating Temperature of the Motor During the operation the motor temperature shoul
3. User Manual of QUICRUN Series Sensored Brushless Motor Thank you for purchasing the QUICRUN 3650 SENSORED brushless motor s for RC cars The high power system can be very dangerous so please read this manual carefully before using and follow the operating procedures strictly In that we have no control over the installation use and maintenance of this product no liability shall be assumed nor accepted for damages losses or costs resulting from the use of this product Besides we own the right to change the product design appearance functions and operational requirements without any notifications Safety Notes This product is NOT a toy and it is for use by adults and teens over 14 only so please keep it out of children s reach Please keep the following points in mind otherwise it may damage the product and cause property loss and physical injuries to users 1 Never leave this product unsupervised when it is powered on If any problem occurs the product may cause a fire and jeopardize peripheral devices Please check wire sequences between the ESC amp the motor carefully before the connection to avoid any possible mistakes 3 Please insure all the wires and interconnecting pieces are well insulated before the connection as short circuits may damage the product Never allow water oil fuel or other conducting liquids to get inside this product or other electronic parts as these liquids may contain harmful minerals for electrical
4. d be lower than 90 C 194F Temperatures above 90 C will demagnetize the magnet amp may melt the coils and eventually damage the ESC because of strong current Therefore the most effective way to prevent over heat is to select the right gear ratio 2 Principle of Gear Selection To avoid potential risks caused by overheating which may lead to ESC motor damage or malfunction please start with very small pinion and check ESC amp motor temperatures frequently throughout a run This is the only way to guarantee that you are not causing excessive heating If Motor and the ESC temperatures remain stable and low in the running then you can slowly increase the pinion with more teeth while again monitoring the temperatures to determine the safe gearing for your vehicle and motor Because the climate and track conditions always change please keep monitoring ESC amp motor temperatures to protect your electronics from damage Applicable Current Point of mm mm M O P 3 17 Diameter Car Fl Monster amp Off Road Buggy 2WD SC Truck Truck STOCK SPORT Race choose the motor base on competition rules Free casual run for new beginners Rock Crawler 21 5T only 1 10 1 12 On Road Truggy Drifting www hobbywing com HW SM311DUL 20131105 Page 1 3 Gear Ratio s Suggested The right form shows some rough data about gear ratios these Vehicle Type Battery 1057 13 51 17 5T 21 5T recommended ratios are reference values whe
5. n setting the ESC to Touring Car for Small track 7 4V LiPo the Zero ae e If ee tae aie how ie set 7 see Touring Car for Bigtrack 7 4V LiPo gear ratio please begin with a big ratio I e small pinion ana then 1 12 Tourine C 3 7V LiP 42 51 66 66 adjust as required or consult with on site drivers who are using the a same power unit for basic information 2WD Buggy 7 4V LiPo ee LAN e aintenance For prolonging the motor life and raising its efficiency we recommend users to check the bearing and clean the motor regularly and the specific interval depends on the usage frequency and terrains Please follow the assembly diagram below to assemble the motor and disassemble in reserve order 1 To assemble the bearing of the front end bell 2 motor rotor 3 dirt proof silicon ring OK aS 9 Note when assembling the dirt proof silicon ring three screw holes should align to relevant hole sites inside 6 the back end bell Note the bearing should align to the corresponding hole site inside P 4 sensor board onto the back end bell 5 screws for fastening the sensor board KPSN S Y J H 2 As shown position of the sensor port after assembling 7 screws for fixing the motor 8 screws for fixing golden connectors 9 picture of the finished product 10 Parts List N 1 2 3 As of N G LF For high resolution assembly diagram please visit our website at www hobbywi
6. ng com Parts List As shown in the diagram above the QUICRUN 3650 SENSORED motor includes 1 Bearing 3 175x9 525x3 967mm xlpcs 2 Motor Rotor xlpcs 3 Outer Shell with Front End Bell xlpcs 4 Sensor Board xlpcs 5 Back End Bell xlpcs 6 Dirt proof Silicon Ring xlpcs d Golden Connestor 38ets 8 Screws for Fixing the Motor M2 50x48mm 9 Screws for Fastening the Sensor Board x3pcs M2 00x3 0mm x3pcs 10 Screws for Fixing Male amp Female Connectors 11 Hall Sensor Wire 2PC 80mm amp 200mm ee M1 60x5 5mm x3pcs xl pcs Product Name Specification Optional Accessories 30830000001 540 MOTOR BEARING 3 175 R2ZZ bearing 3 175 9 525 3 967 Replaceable Part Part No Thin magnet No cooling fan 30850000034 QUICRUN 3650 Rotor 7 12 5 Diameter of the through hole in the rotor 7mm Outer diameter of the magnet 12 5mm IFOBBYYUMG Hobbywing Technology Co LTD www hobbywing com
7. they often differ in colors Phase wire A is Blue Phase wire B is Yellow and Phase wire C is Orange Please note the ESC mark while connecting ESC output wires to motor power wires and ensure connections are A A B B and C C 2 If you are using a sensored ESC please insure Hall sensor wires are clean and undamaged then connect them in the correct direction to the sensor ports of the motor amp the ESC respectively Warning In such a case the wire sequence of the ESC and the motor must strictly follow the rules of A A B B and C C Do not change the wires sequence 3 While if the ESC is a sensorless one then connect the motor and the ESC according to the above way may cause the motor to rotate in the opposite direction because definitions of phase A B C are different among manufacturers at this time you only need to swap any of two wire connections 3 Checkup Recheck the installation and all the connections carefully before turning on the power Specifications Figure 1 Current Purchase Resistance No load ax at the Dimension Shaft Model KV Lipo Number Q QUICRUN 3650 10 5T 30404110001 3300KV QUICRUN 3650 13 5T 30404110002 QUICRUN 3650 17 5T 30404110003 oom Length of t QUICRUN 3650 21 5T 30404110004 1700KV 0 0895 alae ae 52 5 oe Notes M O P Maximum Output Power 1 The maximum output power is the test value obtained when the voltage is 7 4V the ESC timing is set to 0 It is neither the
Download Pdf Manuals
Related Search