TG30 English User`s Manual
Contents
1. User s Guide EXTECH INSTRUMENTS A FLIR COMPANY Wire Tracer Kit Model TG30 CONTINUITY TEL LINE POWER Tone Generator Transmitter EXTECH 1a30 Introduction C Congratulations on your purchase of Extech s Model TG30 This transmitter and probe kit is used to quickly trace and identify cables or wires within a group and also check the operation of phone lines With proper use and care this meter will provide many years of reliable service Specifications Power Transmitter 9V NEDA 1604 1604AL Probe 4 LR44 157 AG13 A76 or equivalent Operating Temperature 100 to 50 C 14 to 122 F Operating Humidity lt 80 RH Altitude 2000 meters Dimensions Probe 147x28x28mm 5 8x1 1x1 1 Transmitter 67x103x23mm 2 6x4 1x0 9 Weight Probe 30g 1 10z Transmitter 120g 4 20z Meter Description Transmitter 1 DaRoN Probe NQOaRroON Function switch OFF T L Tx CONT Continuity led Telephone Line led Power led Battery compartment rear Modular connectors Tone Generator Transmitter Signal receiver Power LED Sensitivity adjustment Power button Pocket clip Battery compartment Speaker Adaptor 1 2 3 RJ11 socket connect to transmitter modular connector CATV Type F connector Alligator clips 2 TG30 EU EN V1 3 6 09 Operating Instructions A CAUTION Always test the probe and transmitter for proper operation before2. s accumulators at collection points in your community or wherever batteries accumulators are sold Disposal Follow the valid legal stipulations in respect of the disposal of the mum device at the end of its lifecycle Copyright 2005 Extech Instruments Corporation All rights reserved including the right of reproduction in whole or in part in any form 4 TG30 EU EN V1 3 6 09
3. up the signal generated by the transmitter Rotate the volume sensitivity control on the top of the probe for the appropriate level and sensitivity to identify and trace the wire The tone will be the loudest on the wires directly connected to the transmitter Telephone Line Test 1 Switch the transmitter to the OFF position Insert the modular plug into the phone line Observe the TEL LINE LED for the following conditions a Bright Green Working line not in use correct polarity b Dim Green or Red Working line not in use polarity undetermined c Bright Red Working line not in use reverse polarity d Bright Green Red flashing Working ringing line e No light Open pair no service 3 TG30 EU EN V1 3 6 09 Continuity Test 1 Switch the transmitter to the CONT position 2 Connect to the wire pair with the alligator clips The buzzer will sound and the CONTINUITY led will light if there is continuity less than approximately 1kQ Battery replacement Probe Install new batteries by turning the speaker and pocket clip 4 turn to the left remove the battery door and replace the four LR44 batteries Observe battery polarity Transmitter Remove the rear battery compartment door and replace the 9V battery You as the end user are legally bound Battery ordinance to return all used batteries and accumulators disposal in the household garbage is prohibited You can hand over your used batterie
4. use A CAUTION The transmitter is not designed for use on energized circuits Connecting to any voltage source greater than 52VDC may damage the circuit Note The transmitter will not generate a signal into a short circuit Self Test 1 2 Set the transmitter power switch to the Tx position Adjust the probe sensitivity to MAX clockwise position Press and hold the probe power button The red LED will light Move the probe close to the transmitter cable and note that the audible trace tone and sensitivity adjustment perform normally Cable Wire tracing 1 QOaPo 8 Select the transmitter termination required Permanently attached are RJ11 and RJ45 connectors Plug the RJ45 connector into the adaptor cable to obtain CATV type F connection or alligator connectors Connect the transmitter to the cable a For cables terminated at one end connect the red alligator clip to a wire and the black alligator clip to equipment ground b For unterminated cables connect the red alligator clip to one wire and the black alligator clip to another wire c For cables with modular connectors plug the RJ11 RJ45 or type F connectors directly into the mating cable connectors Set the transmitter power switch to the Tx position Adjust the probe sensitivity to MAX clockwise position Press and hold the probe power button The red LED will light Hold the insulated probe tip against the wire in question to pick
Download Pdf Manuals
Related Search