Home

Untitled

1. bracket Save the bracket screw for later use Align the controller card horizontally with respect to the slot and insert it into the slot firmly and evenly Take care not to force it into the slot Once you have properly positioned the controller card into the slot fasten it to the computer case with the screw you have just saved Mount the hard disk s on the computer case Connect the power cable to the hard disk s Connect the SATA hard disk s to the controller card with the SATA cable Connect the computer case s front panel Hard Disk LED cable to pin header JP4 Connect the one end of the LED cable included to pin header JP5 and the other end to your JP4 motherboard s HDD LED connector Secure the computer case and switch on your computer gt 4 0 RAID BIOS SETUP Skip this section if you are not going to create a RAID virtual disk Press the Ctrl M key combination during the controller card s POST Power On Self Test After pressing Ctrl M you may have to wait a few seconds before the BIOS screen appears Figure 2 shows the messages displayed during the POST of the SATA controller card Marvell 88SE91xx Adapter BIOS Version 1 0 0 1008 PCI E X1 Bandwidth Usage 5 0Gbps Configure SATA as AHCI Mode Virtual Disk No Virtual Disk Physical Disk 10 Disk Name size speed Q SATA ST3750330MS 715GB 8 SATA ST3750330MS 715GB 16 ATAPI SONY DVD ROM DDU1615 Not Available SS lt Ctrl gt lt
2. LogiLink PC0064 SATA 6Gbps H W RAID PCI Express Card User Manual EN Ca Do not throw the appliance away with the normal household waste at the end of its life but hand it in at an official collection point for recycling By doing this Wg yOu will help to preserve the environment 1 0 Safety Instruction Put the Device always on a stable and straight Surface In case of falling it can be damaged Don t place the Device into direct Sunlight or in Places with high Temperature This can damage the Device or shorten his average useful Life Don t place it in the near of Heat Sources like Radiators or other heat producing Devices Don t expose the Device to Rain Water Wetness or high Humidity Don t place it in the Bathroom or the Kitchen in the near of a Sink Avoid the direct Contact with Water Don t try to open the Device Prior to the first use of our product make a backup of your data We are not liable for any loss of data unless you can accuse us intention or gross negligence In any case liability for loss of data is limited to the effort that is necessary to restore from existing backup copies Congratulations to the Purchase of the PC0064 Please read the Manual and Safety Instructions before using the Product for the first Time Otherwise Damage can be the Result 2 0 Introduction The PCI Express SATA controller card PC0064 brings a high performance 6 0Gbps hardware RAID 0 RAID 1 solution t
3. M gt to enter BIOS Setup or lt Space gt to continue_ Follow the on screen help and information to configure various RAID functions such as selecting RAID Level RAID 0 or RAID 1 selecting RAID 0 stripe size 32K or 64K manually rebuilding a RAID 1 virtual disk etc If you created a RAID virtual disk but later you don t want the RAID function simply erase the RAID configuration data in the BIOS Note The PATA IDE interface does not support RAID function 5 0 Driver Installation 5 1 Windows 2003 2008 XP Vista 7 1 2 Start Windows and insert the driver CD into the CD ROM drive assume drive D Windows will automatically detect the SATA card Select Locate and install driver software recommended and click Continue And then select I don t have the disc Show me other options Click on Browse my computer for driver software and then browse to the following folder on the driver CD according to your operating system e Win XP Vista Server 2003 2008 and Win 7 32 bit D Marvell 88SE91xx Windows Win_32bit e Win XP Vista Server 2003 2008 and Win 7 64 bit D Marvell 88SE91xx Windows Win_64bit Follow the on screen instructions to install the driver After successful installation the SATA card is listed under Storage controllers as Marvell 91xx SATA 6G Controller For the RAID controller an additional device Marvell 91xx Config SCSI Processor Device is detected Select Locate and install
4. Supports communication speed of 6 0Gbps 3 0Gbps and 1 5Gbps e Compatible with SATA III 6Gbps SATA II 3Gbps SATA I 1 5Gbps hard drives and SSD s Supports Gen 1i Gen 1x Gen 2i Gen 2m Gen 2x and Gen 3i Supports Hardware RAID 0 and RAID 1 Supports Native Command Queue NCQ Supports SATA Port Multiplier FIS based switching or command based switching Supports SATA port Hot Plug and AHCI 1 0 e Supports ATA and ATAPI commands Parallel ATA PATA IDE Interface e One PATA port supporting ATA ATAPI IDE devices Master and Slave e Compliant with ATA ATAPI 7 specification e Supports DMA protocols and UDMA 6 133Mbps data transfer rate e Supports Multiword DMA and PIO modes for data transfer e Supports IDE programming interface 2 2 Package Content e 1x PCI Express SATA RAID card e 1x Driver CD e 1x User manual e 1xLED cable 3 0 Hardware Installation WARNING Before installing and activating RAID function please make sure you have a complete backup of your existing data from your hard drives Manufacturer is not responsible for data loss due to abuse misuse or neglect Should you have any installation problem please contact your dealer for assistance Turn off your computer and all external devices connected to it Disconnect your computer from the power sources Open the computer case Refer to your computer user manual for more details Find an available PCI Express 2 0 slot and remove the slot
5. driver software recommended and click Continue And then select I don t have the disc Show me other options Click on Browse my computer for driver software and then browse to the following folder on the driver CD according to your operating system e Win XP Vista Server 2003 2008 and Win 7 32 bit D Marvell 88SE91xx Windows RAID Win_32bit e Win XP Vista Server 2003 2008 and Win 7 64 bit D Marvell 88SE91xx Windows RAID Win_64bit Follow the on screen instructions to install the driver After successful installation the device is listed in the Device Manager as Marvell 91xx Config Device under System devices 5 2 For Linux Note Marvell does not provide Linux drivers for AHCI and IDE ATA devices m Drivers for AHCI devices Linux distributions contain Inbox drivers for AHCI devices The drivers are installed automatically during the Linux OS installation m Drivers for IDE ATA devices Linux distributions with kernel version 2 6 19 and above include inbox drivers for IDE ATA devices Source http www kernel org pub linux kernel v2 6 ChangeLog 2 6 19 In most distributions the kernel does not load the inbox drivers for IDE ATA devices by default The procedure for enabling support for IDE ATA devices in Linux is as follows m Enabling Support for IDE ATA Devices during a Clean Installation of Linux This section describes the procedure for enabling support for IDE ATA devices during a clean installat
6. ion of Linux To enable support for IDE ATA devices during a clean installation of Linux 1 Boot from the Linux installation CD DVD 2 Select Installation and press Enter 3 Type the following command into the Boot Options command line ata_generic all_generic_ide 1 4 Press Enter to continue with the Linux OS installation m Enabling Support for IDE ATA Devices on an Existing Installation of Linux This section describes the procedure for enabling support for IDE ATA devices on an existing installation of Linux To enable support for IDE ATA devices on an existing installation of Linux 1 Login as root 2 Right click the Desktop and select Open In Terminal 3 Type the following commands Is cd boot grub vim menu lst 4 Type the following command at the end of the kernel line for the title paragraph that lists the version information for the Linux distribution ata_generic all_generic_ide 1 5 Browse to File and select Save 6 Reboot the system for the changes to take effect 5 3 Updating Drivers The latest drivers and last minute change to this document are available on this website http www drivers download com Search for the following Download Code from Drivers Search Chipset Description Download Code Marvell PCI Express to SATA 6Gbps DL 0141101 88SE9128 Hardware RAID controller card main requirements of the Directive 2004 108 EC of the European Parliament and the Council of E
7. o desktop consumer storage applications utilizing a native 1 Lane PCI Express 2 0 interface The card supports SATA 6Gbps devices complaint with Serial ATA Revision 3 0 specification and ATA ATAPI 7 specification It is also backward compatible with SATA 1 5Gbps and 3 0Gbps devices The LED indicator headers on the card are specially designed so that the front panel LED indicator can show Read Write activities of any hard disk drives connected to the card The orientation and position of the two internal SATA ports are well designed so that cable wiring is very easy in small form factor computer chassis The card also comes with an internal Parallel ATA port providing support for up to one legacy gt ATA ATAPI storage devices such as IDE hard drives A A 2 1 Specification General e Chipset Marvel 88SE9128 e Compliant with PCI Express 2 0 Base Specification e Based on Marvel 88SE9128 PCI Express 2 0 SATA 6Gbps hardware RAID controller e Lane PCI Express 2 0 interface supports communication speed of 2 5Gbps and 5 0Gbps e Unique Hard Drive Activity LED indicator circuit design The LED blinks when there is read write activity on any one of the hard drive connected to SATA port of this add on card e Supports Windows 7 32 64 bit Server 2008 32 64 bit Vista 32 64 bit Server 2003 32 64 bit XP 32 64 bit and Linux Serial ATA SATA Interface e Two SATA 6 0Gbps ports e Compliant with Serial ATA Specification 3 0 e
8. urope concerning telecommunications and terminals regarding the Safety and health of users and of electro magnetic interference compliance The CE has been demonstrated These statements are deposited by the manufacturer C The CE mark confirmed that this product meets the

Untitled

Contents

Download Pdf Manuals

Related Search

Related Contents