INSTALLATION MANUAL
Contents
1. to account for the focus shift or see the Focusing Alternate Lenses section below for further instruction 5 Retighten the lock screw if necessary 6 Install the Dome Cover by aligning the captive fasteners with the mating threaded holes on the camera housing 7 When mounting the Dome Cover to the Camera Housing ensure that the gasket is properly seating and not folded Failure to do so may result in water and dust ingress Changing the Lens 1 Remove the Dome Cover by loosening the captive fasteners Loosen the lens lock screw using a phillips head screwdriver if necessary Only do so if lens seems very tight when turning Manually unscrew the lens this may take several seconds Replace lens Retighten the lock screw if necessary ey a Reinstall Dome Cover per instructions outlined above Page 11 support arecontvision com S Arecont Vision Celebrating 10 Years of Leading the Way in Megapixel Video Made in the USA 2003 2013 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Focusing Alternate Lenses When focusing the 6mm 8mm 12mm or 16mm lens options you will encounter a focus shift when using the bubble To account for this follow these steps Focus the camera without the bubble Rotate the lens per the chart below The rotation will account for most of the focus shift Put cover2. with bubble on You should be close to being focused a ea Remove cover and rotate a couple degrees at a time in either direction until you gain the desired image MPM16 0 lt 3 4 CCW MPM12 0 1 4 CCW MPM8 0 gt 1 accw 60 MPMB6 0 1 8 CCW Example Using a 16mm lens you will focus the lens without the bubble until you get the desired image Rotate the lens almost of a turn 250 Put the bubble on and view the image It should be almost in focus Remove the bubble and rotate a degree or two in one direction and view the image with the bubble on Depending on the image you may need to adjust in the opposite direction or continue in the same direction until the desired image is obtained Accessing the Digital Input and Output Connector The 4 position connector inside camera housing located on the main circuit board used for I O can be accessed by removing the track plate Simply loosen the three screws indicated in the image below lift the track plate and find the connector The approximate connector position is indicated by the red circle below Page 12 support arecontvision com S Arecont Vision 2003 2013 Made in the USA i l Ea 7 ES Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Digital Input and Output Use 4 position conne
3. MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE NON INFRINGEMENT AND THE IMPLIED CONDITION OF SATISFACTORY QUALITY ALL LICENSED PROGRAMS ARE LICENSED ON AN AS IS BASIS WITHOUT WARRANTY ARECONT VISION DOES NOT WARRANT THAT I THE OPERATION OF THE PRODUCTS OR PARTS WILL BE UNINTERRUPTED OR ERROR FREE Il THE PRODUCTS OR PARTS AND DOCUMENTATION WILL MEET THE END USERS REQUIREMENTS Ill THE PRODUCTS OR PARTS WILL OPERATE IN COMBINATIONS AND CONFIGURATIONS SELECTED BY THE END USER OTHER THAN COMBINATIONS AND CONFIGURATIONS WITH PARTS OR OTHER PRODUCTS AUTHORIZED BY ARECONT VISION OR IV THAT ALL LICENSED PROGRAM ERRORS WILL BE CORRECTED For RMA and Advance Replacement information visit ArecontVision com Page 4 support arecontvision com a S Arecont Vision 2003 2013 E Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Installation Overview 4 Ceiling NPT Port o Camera Gimbals 4X Gasket i i d Dom ver Captive Fasteners ome Cove Page 5 support arecontvision com S Arecont Vision 2003 2013 Made in the USA i E ES Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omn
4. OTE Wiring methods shall be in accordance with the National Electrical Code NFPA 70 ANSI and with all local codes and authorities having jurisdiction Wiring should be UL Listed and or Recognized wire suitable for the application For use in ducts plenums and other air handling areas replace Auxiliary Cable provided with CMP CL2P or CL3P type wires Page 14 support arecontvision com S Arecont Vision 2003 2013 Made in the USA _ i E ES Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual LED Indicators Yellow established Camera has been accessed Normal operation Page 15 support arecontvision com S Arecont Vision 2003 2013 Made in the USA Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Support Arecont Vision FAQ Page Located at ArecontVision com Check the following before you call Restore camera to factory default with AV100 AV200 or the camera webpage Upgrade to the latest firmware by visiting ArecontVision com Isolate the camera on a dedicated network and test with AV100 or AV200 Swap the troubled camera with a known good ca
5. SurroundVideo Omni INSTALLATION MANUAL AV12176DN NL AV121 76DN 28 AV12176DN 08 AV20175DN NL AV20175DN 28 AV20175DN 08 Seeman J Arecont Vision Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual MicroDome Surface Mount Installation Contents PK toe Be g 1d 0 ao ear ee ee ro ne eee ee ee nee ee 3 WAY AP FAY WON lO a EEE se E A EA E E EN E E E oon ce E E A A AE 4 SaO OVE VOW oaeee EE A EE E E E EE E EE A E A EEE 5 Ganera on Dano E E E E 6 Eae eE EEE a E A A E AA EA N A ANNAE N EN E AANE A eee AN 7 CaA ae E E E 9 LEENE S g ANE EE EELE E E E E EEE PEET A E PE E E anne 10 CFS VS NE LCN ee A T E A 11 Accessing the Digital Input and Output Connector sessssssssrersesreresrreserrereserersrreresererssreresererssrereserereseeresereresreresene 12 Detar NOU anA O IE a E E E ETE E E AE 13 AOUN POW CU e E E A E AON 14 LEDINO TOG e a E A E E E E E E E 15 Moan BESE Pra CE a EE E E A E masqardaveanterte 17 Wall Mount Accessory AV WMIB ivcsicsessanacessdianuncoasniansdooneseenacuuass iianesedeewausestosnia vanoaiasedlebesehiawaeataanuseeeseniesscroaseean 19 Pendant Mount Accessory AV PMIB c scssssscsrscssossearscusosseauseuseusearceusessearcauseuseurcauseuseascanseuseurcanseuseursanseuseureanee 20 Page 2 support arecontvision com S Arecont
6. Vision 2003 2013 Made in the USA i l E E ES Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Package Contents SurroundVideo Omni Mounting Kit Ceiling template 3x Mounting Screws 6x1 for wood or sheet metal 3x Drywall Masonry Mounting Anchors Ceiling Gasket Network Patch Cable Security Torx Tool Power Cable Aux Power Cord I O Cable Digital Input and Output Adapter Arecont Vision CD Manual Warranty Installation Software Notes 1 Camera Operating Temperature 40 C 40 F to 50 C 122 F Wiring methods shall be in accordance with the National Electrical Code NFPA 70 ANSI and with all local codes and authorities having jurisdiction Wiring should be UL Listed and or Recognized wire suitable for the application 3 Always use hardware e g screws anchors bolts locking nuts etc which are compatible with mounting surface and of sufficient length and construction to insure a secure mount 4 For use in ducts plenums and other air handling areas replace Auxiliary Cable provided with CMP CL2P or CL3P type wires Page 3 support arecontvision com S Arecont Vision 2003 2013 Made in the USA i aes N ES Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvi
7. brating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Pendant Mount Accessory AV PMJB Installation Notes 1 4x mounting screws are 10x1 wood or sheet metal screws 4x mount anchors also included 2 Always ensure gaskets are properly seated 3 Use Teflon tape on threaded interfaces 1 5 NPT Page 20 support arecontvision com S Arecont Vision 2003 2013 Made in the USA i E ES Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Mount Template 150 196 21 40 gt 5 KMJ Arecont Vision Cy Made in the USA Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Contact Arecont Vision Technical Support one of three ways Online Portal Support ArecontVision com Phone 1 818 937 0700 option 1 Email support arecontvision com Page 22 support arecontvision com S Arecont Vision 2003 2013 Made in the USA i E ES Celebrating 10 Years of Leading the Way in M
8. captive fasteners with the mating threaded holes on the camera housing 11 When mounting the Dome Cover to the Camera Housing ensure that the gasket is properly seating and not folded Failure to do so may result in water and dust ingress Best Practice Tips gt When mounting to vertical surface it is best to use the Wall Mount Accessory which includes a Junction Box gt For outdoor use it is always best to properly seal the product using caulk around the edges to prevent water ingress from mounting to porous or uneven surfaces gt Use Teflon tape on threaded interfaces Page 10 support arecontvision com Made in the USA S Arecont Vision 2003 2013 a N ES Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Focusing the Cameras 1 Open a live view of the camera from your web browser or the AV Software provided AV200 Loosen the lens lock screw using a phillips head screwdriver if necessary Only do so if lens seems very tight when turning Lock screw should be tightened enough to provide some friction against the lens to avoid focusing problems 3 Manually rotate the lens to adjust the focus until the desired image is obtained For some lenses a focus shift will occur once the bubble is in place Hold the bubble up to the lens when focusing
9. ctor inside camera housing to interface with Digital I O DIGITAL I O BLACK IN WHITE IN YELLOW OUT ORANGE OUT ORANGE YELLOW WHITE BLACK AWG28 AWG28 AWG28 AWG28 UL1213 UL1213 UL1213 UL1213 a a A as ll A oi LET MOLEX HOUSING 51021 0400 CONTACTS 50079 8000 OR COMP Input Voltage V Measured between and terminals Output Current mA Measured between and terminals Applied Voltage Range 0 80V NOTE Both the input and the output are electrically isolated from the rest of the camera s electrical circuitry via general purpose photo couplers The input is additionally protected with a serial 250 Ohm resistor and a debouncing circuit Duration of any input signal should be at least 5ms to comply with the requirements of the debouncing circuit Page 13 support arecontvision com S Arecont Vision Celebrating 10 Years of Leading the Way in Megapixel Video Made in the USA 2003 2013 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Auxiliary Power If the camera is powered by a separate outside AC or DC power source run the supplied power cable through the access hole on the camera housing and connect the power cable to the 2 position connector on the main camera board The approximate location of the 2 position connector is circled in red below N
10. egapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com
11. i Installation Manual Camera Setup The SurroundVideo Omni is user configurable Each individual sensor can be positioned in a variety of ways Below are some example configurations top left to bottom right 1 270 2 Straight Line 3 360 or Hallway 4 180 or Panoramic 5 Random Example 6 Random Example Prior to installing the camera thought should be given to the sensor positions It is always easier to make adjustments before the camera is installed Page 6 support arecontvision com a K Arecont Vision 2003 2013 o o Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Camera Adjustment To position a sensor simply loosen the captive fastener to release the camera assembly from the track plate 4 40 Screw Captive Fastener Track Plate Next position the camera in the desired location on the track plate Screw holes around the circumference are spaced in 5 degree increments Note the arrows marked at 45 degrees as reference points 45 Reference Mark Page 7 support arecontvision com S Arecont Vision 2003 2013 Made in the USA E ES Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Visio
12. ideo Made in the USA 2003 2013 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Installation 1 Wiring methods shall be in accordance with the National Electrical Code NFPA 70 ANSI and with all local codes and authorities having jurisdiction Wiring should be UL Listed and or Recognized wire suitable for the application Operating Temperature 40 C 40 F to 50 C 122 F 3 Always use hardware e g screws anchors bolts locking nuts etc which are compatible with mounting surface and of sufficient length and construction to insure a secure mount Visit http www arecontvision com and check to ensure your camera has the most current firmware 5 If using the NPT port always use Teflon tape around threads to ensure proper sealing After plugging in the network cable check that the indicator LED s are indicating the desired conditions see LED Indicator table 7 Use Arecont Vision software AV200 located on the CD or available for download at our website www arecontvision com for camera discovery and setup see Instruction Manual located on CD or available on our website 8 Adjust the individual cameras to obtain the desired fields of view see Focusing Instructions 9 Lens may be further secured by tightening the lens lock screw using Phillips head screwdriver 10 Install the Dome Cover by aligning the
13. mera to see if the problem follows the camera or stays at the location Contact Arecont Vision Technical Support one of three ways Online Portal Support ArecontVision com Phone 1 818 937 0700 option 1 Email support arecontvision com Page 16 support arecontvision com S Arecont Vision 2003 2013 Made in the USA E N ES Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Installation Best Practice Wind Vinyl electrical Adding Teflon thread sealing Be iinstabanen tape on all cables tape to all male threads Connect NPT conduit pipe to junction box adapter Does conduit pipe go through the wall Make sure position of conduit hole is at the lower side Tighten all camera forming a drip loop below the camera using 4 galvanized or flex conduit and appropriate fittings screws and 3 4 NPT plugs Caulk the perimeter of the mounting area End Installation Not Recommended yi ae ae ka Conduct periodic inspections of the installation Rust on the metal parts or screws may result in damage to camera Not Recommended Recommended J Arecont Vision Celebrating 10 Years of Leading the Way in Megapixel Video Made in the USA 2003 2013 1 818 937 0700 877 CAMERA 8 www arecont
14. n SurroundVideo Omni Installation Manual Sensor numbering is indicated on the track plate The number on the track plate corresponds to the sensor number in the camera software Sensor positioning and alignment should be considered before camera installation It is easier to adjust the individual camera positions before the camera is installed into a ceiling The three slots in the track plate provide additional adjustment of the camera after installation Simply loosen the three screws to rotate the plate then tighten the three screws after alignment This feature is most useful for repositioning the cameras mounted to the center locations after camera installation Page 8 support arecontvision com S Arecont Vision Celebrating 10 Years of Leading the Way in Megapixel Video Made in the USA 2003 2013 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Camera Alignment Alignment of the individual cameras is critical to setup The individual cameras when placed on the circumference of the track must be in a counterclockwise sequence to create proper alignment when viewing the camera Sensor 2 Sensor 3 Sensor 1 Sensor 4 Counterclockwise Sensor 3 Counterclockwise Sensor 1 Page 9 support arecontvision com S Arecont Vision Celebrating 10 Years of Leading the Way in Megapixel V
15. sion com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Warranty Information 3 Year Limited Warranty ARECONT VISION warrants to Purchaser and only Purchaser the Limited Warranty that a each Product shall be free from material defects in material and workmanship for a period of thirty six 36 months from the date of shipment the Warranty Period b during the Warranty Period the Products will materially conform with the specification in the applicable documentation c all licensed programs accompanying the Product the Licensed Programs will materially conform with applicable specifications Notwithstanding the preceding provisions ARECONT VISION shall have no obligation or responsibility with respect to any Product that i has been modified or altered without ARECONT VISION s written authorization i has not been used in accordance with applicable documentation ili has been subjected to unusual stress neglect misuse abuse improper storage testing or connection or unauthorized repair or iv is no longer covered under the Warranty Period ARECONT VISION MAKE NO WARRANTIES OR CONDITIONS EXPRESS IMPLIED STATUTORY OR OTHERWISE OTHER THAN THE EXPRESS LIMITED WARRANTIES MADE BY ARECONT VISION ABOVE AND ARECONT VISION HEREBY SPECIFICALLY DISCLAIMS ALL OTHER EXPRESS STATUTORY AND IMPLIED WARRANTIES AND CONDITIONS INCLUDING THE IMPLIED WARRANTIES OF
16. vision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Camera Discovery Setup and Configuration For camera discovery and setup please use Arecont Vision software AV200 which you can find on the CD included with your camera or at htto www arecontvision com softwares oh The user manual for the AV200 software is included on the CD and is also located on our website To configure the camera use either the AV200 software or the web interface utility The web interface can be accessed by typing the camera IP address into your web browser or by clicking on the web interface button in AV200 The user manual for our web interface is included on the CD and is also located on our website Page 18 support arecontvision com S Arecont Vision 2003 2013 Made in the USA oan o N ES Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERA 8 www arecontvision com avsales arecontvision com SurroundVideo Omni Arecont Vision SurroundVideo Omni Installation Manual Wall Mount Accessory AV WMJB 1 5 NPT Gasket Installation Notes 1 4x mounting screws are 10x1 wood or sheet metal screws 4x mount anchors also included 2 Always ensure gaskets are properly seated 3 Use Teflon tape on threaded interfaces Page 19 support arecontvision com a KOJ Arecont Vision 2003 2013 _ i E ES Cele
Download Pdf Manuals
Related Search