DIALighting IW19
Contents
1. 3 How To Set The Unit 3 1 Control Panel CA Ga 1 Display Shows the various menus and the selected functions LED 2 POWER ON Power On 3 DMX ON DMX input present 4 Button MENU To select the programming functions v DOWNI Togo backward in the selected functions A UP To go forward in the selected functions 4D ENTER To confirm the selected functions 5 DMX input DMX512 link use 5 pin XLR cable to link the unit and DMX controller 6 DMX input DMX512 link use 3 pin XLR cable to link the unit and DMX controller 7 DMX output DMX512 link use 5 pin XLR cable to link the next unit 8 DMX output DMX512 link use 3 pin XLR cable to link the next unit 9 Mains input Connects to power supply 10 Mains output Connects to next fixture 11 Fuse T 6 3A Protects the unit from over voltage or short circuit 3 2 Main Function To select any of the given functions press the MENU button until the required function is showing on the display Select the function by pressing the ENTER button and the display will blink Use the DOWN UP buttons to change the mode Once the required mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Press and hold the MENU button for about one second or wait for one minute to exit the menu mode The main functions are shown o2. DIALighting IW19 10 ZOOM User Manual Please read the instruction carefully before use oD TABLE OF CONTENTS hs SAPO EM NStrUCHONS esine ararat tusks on a E aaa raa ee aeaa 2 Technical Specifications een eaea aaa a ea ana oriai Ea SHOW TO SEtTNSUNitaee arid e a AA E A AE 3 1 Control Panel aradon e n devine a a ti e dessa eevee J2 Mam UO O A E as er Ni ae E 3 3 HOME POSITION AGIUSE sivvivcrvoxsionsciceer iver senivinservdbemmienivesbieasabeave manned 12 4 Control By Universal DMX Controller ccc cccccccccecscsceseseeseeseeeseecsesseeeeeessseeees 13 4 AUDI 5312 COnNecthONs t coast cee arin te ctariad aay abort das a a earl Ereet a aiia 13 AD AOGFESS SEEING EAEE EST E EALES AIEE A EAA AA EEN TA neediness 14 4 3 DMX SIZ CONEA O n aaae A E E EESTE Aa AEri aE 15 5 troubleshooting innan A E ae a ee 16 6s Fixture Cleaning e n er e E eaa eE O A EE E EEVEE 16 1 Safety Instructions Please read the instruction carefully which includes important information about the installation usage and maintenance WARNING Please keep this User Manual for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit It s important to ground the yellow green conductor to ear
3. button to select Pan Inverse Tile Inverse P T Feedback BL O P T Moving White Balance Cooling Mode Dimmer Curve or Dimmer Speed Pan Inverse To select Pan Inverse press the ENTER button to show the PAN INVERSE on the display Use the UP DOWN button to select No normal or Yes pan inverse press the ENTER button to setup Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode Tilt Inverse To select Tilt Inverse press the ENTER button to show the TILT INVERSE on the display Use the UP DOWN button to select No normal or Yes tilt inverse press the ENTER button to setup Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode P T Feedback To select P T Feedback press the ENTER button to show the PAN TILT FEEDBACK on the display Use the UP DOWN button to select No Pan or tilt s position will not feedback while out of step or Yes Feedback while pan tilt out of step press the ENTER button to setup Press the 7D MENU button back to the last menu or let the unit idle one minute to exit menu mode BL O P T Moving To select BL O P T Moving press the ENTER button to show the BLACKOUT WHILE PAN TILT MOVING on the display use the UP DOWN button to select No normal while pan tilt moving or Yes blackout while pan tilt moving press the ENTER button to setup Press the MENU button back to the last menu or let the unit idle one minute to exit
4. menu mode White Balance To select White Balance press the ENTER button to show the WHITE BALANCE on the display use the UP DOWN button to select Red Green or Blue Once selected press the ENTER button to confirm and use the UP DOWN button to adjust the value from 125 to 255 press the ENTER button to setup Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode Cooling Mode To select Cooling Mode press the ENTER button to show the COOLING MODE on the display Use the UP DOWN button to select Auto Normal or Low Low speed Once selected press the ENTER button to setup Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode Dimmer Curve To select Dimmer Curve press the ENTER button to show the DIMMER CURVE on the display use the UP DOWN button to select Linear Square Law Inverse Squ or S curve Once selected press the ENTER button to store Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode Dimmer Modes 5 5 5 Q Q Q 5 5 5 fe fe DMX Optically Linear Square Law Inverse Square Law S curve 8D Linear The increase in light intensity appears to be linear as DMX value is increased Square Law Light intensity control is finer at low levels and coarser at high levels Inverse Square Law Light intensity control is coarser at low levels and finger at high levels S cure Light intens
5. to high voltage cables that may cause damage or interference to DMX interface circuit C One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition 6 Fixture Cleaning The cleaning must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully 16D Clean the external optics at least every 30 days 17D 18D 19D
6. 5 Orange LEE179 Chrome Orange LEE104 Deep Amber LEE100 Spring Yellow LEEO88 Lime Green LEE738 JAS Green LEE122 Fern Green LEEO89 Moss Green LEE139 Primary Green LEE124 Dark Green LEE116 Medium Blue Green LEE118 Light Blue LEE353 Lighter Blue LEE117 Steel Blue LEE202 Half CT Blue LEE201 Full CT Blue LEE161 State Blue LEE200 Double CT Blue LEE132 Medium Blue LEEO79 Just Blue LEE120 Deep Blue LEEO71 Tokyo Blue LEE181 Congo Blue LEE194 Surprise pink LEE345 Fuchsia pink 15D 025 029 LEE328 Follies pink 020 024 LEE332 Special rose pink 015 019 LEE157 Pink 010 014 LEE790 Moroccan pink 000 009 Open 5 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work 1 Check the connection of power and main fuse 2 Measure the mains voltage on the main connector 3 Check the power on LED B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 Ifthe DMX LED is on and no response to the channel check the address settings and DMX polarity 3 Ifyou have intermittent DMX signal problems check the pins on connectors or on PCB of the unit or the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside
7. e parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact your nearest dealer Installation The fixture should be mounted via its Omega Quick Release Clamp bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the fixtures weight Always use a safety cable that can hold 12 times of the weight of the fixture when installing The equipment must be installed by professionals It must be installed in a place where is out of the reach of people and no one can pass by or under it 2 Technical Specifications lt Extremely small fast and powerful LED moving beam lt DMX Channels 14 channels mode lt Operation modes DMX512 lt Blue LCD display for easy navigation Perfect for stage theatre TV studio rental and discotheques e Input Voltage AC 100V 240V 50 60Hz e Power Consumption 245W e Power Cable Daisy Chain 11 Fixture Max 230V 50Hz 3D 5 Fixture Max 130V 60Hz e Beam Angel 10 60 e LED Source 19 x 10W RGBW LED e Weight 9 2Kgs e Dimension 325 x 188 x 395mm 188 395
8. it or Reset time press the MENU button to exit Factory Setting To select Factory Setting press the ENTER button to show the FACTORY SETTING on the display Press the ENTER button to confirm use the UP DOWN button to select No or Yes the fixture will reset to factory settings and exit menu mode 3 3 Home Position Adjust OFFSET MENU In the main functions hold the ENTER button for at least 3 seconds into offset mode use the DOWN UP button up to select Pan Offset Tilt Offset or Zoom Offset and press the ENTER button to confirm Use the DOWN UP button to adjust the home position of the Pan Tilt or Zoom Once the position has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Press and hold the MENU button about one 12D second or wait for about one minute to exit the menu mode 4 Control By Universal DMX Controller 4 1 DMX 512 Connection DMX OUT DMX512 CONTROLLER COMMON CZ DMX INPUT DMX OUTPUT C COMMON DMX DMX 92 DMX INPUT Not Used 0495 Not Used 1 Ifyou using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last unit 3 Connect the unit together in a dais
9. ity control is finger at low levels and high levels and coarser at medium levels Dimmer Speed To select Dimmer Speed press the ENTER button to show the DIMMER SPEED on the display Use the UP DOWN button to select Fast or Smooth Once selected press the ENTER button to setup Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode Display Setting Enter MENU mode select Display Setting press the ENTER button to confirm use the UP DOWN button to select Display Inverse Backlight Auto Off Backlight Intensity Temperature unit or Display Warning Display Inverse To select Display Inverse press the ENTER button to show the DISPLAY INVERSE on the display Use the UP DOWN button to select No normal or Yes display inverse Once selected press the ENTER button to store Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode Backlight Auto Off To select Backlight Auto Off press the ENTER button to show the BACKLIGHT AUTO OFF on the display Use the UP DOWN button to select No display always on or Yes display goes off one minute after exiting menu mode Once selected press the ENTER button to confirm and store Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode Backlight Intensity To select Backlight Intensity press the ENTER button to show the BACKLIGHT INTENSITY on the display Use the UP DOWN button t
10. le 7 seconds to exit menu mode Please refer to the following diagram to address your DMX512 channel for the first 4 units Channel mode Unit 1 Unit 2 Unit 3 Unit 4 Address Address Address Address 14D 4 3 DMX 512 Configuration 14 channels mode 14 Channels Mode Ch7 Ch8 chi ch2 ch3 cha chs Pan PanFine Tilt TiltFine speed Dimmer Shutter 245 255 open 255 255 Slow 015 255 NoFunction 255 230 244 burst 225 229 open 210 224 sine wave 205 209 open 190 204 random burst pulse 185 189 open 170 184 burst pulse 165 169 open 010 014 Reset All 150 164 random closing pulse 45 149 open 30 144 random opening pulse 25 129 open 10 random strobe 05 open 90 Epeng pulse 000 009 No Function 85 089 open 70 65 Fast 25 0 0 A Ch 12 Ch 13 m n T O00000 Red Green Color Macro Blue White 255 100 255 100 250 255 Open 245 249 Slow 240 244 Medium 235 239 Fast Random Color 230 234 Open 208 229 Counter clockwise slow to fast 202 207 Stop 180 201 Clockwise fast to slow Color wheel rotation effect 175 179 Open 170 174 LEE164 Flame Red 9 LEE135 Deep Gold Amber Ta 164 LEE778 Millennium Gold 155 159 LEEO21 Gold Amber 255 100 255 100 150 154 145 149 140 144 135 139 130 134 25 110 114 105 109 100 104 095 099 090 094 085 089 080 084 075 079 070 074 965 069 60 06 085 089 050 054 045 049 040 044 035 039 030 034 LEE10
11. o adjust the intensity from 1 dark to 10 bright Once selected press the ENTER button to setup and store Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode 9D Temperature Unit To Select Temperature Unit press the ENTER button to show the TEMPERATURE UNIT on the display Use the UP DOWN button to select C or F press the ENTER button to store Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode Display Warning To select Display Warning press the ENTER button to show the DISPLAY WARNING on the display Use the UP DOWN button to select No Normal or Yes display will show the error warning when the unit went wrong press the ENTER button to store Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode Fixture Test Enter MENU mode select Fixture Test press the ENTER button to confirm use the UP DOWN button to select Auto Test or Manual Test Auto Test To select Auto Test press the ENTER button to show the AUTO TEST on the display Press the ENTER button the unit will run built in programs to automatically test pan tilt and zoom Press the MENU button back to the last menu or exit menu mode after auto test Manual Test To select Manual Test press the ENTER button to show the MANUAL TEST on the display Press the ENTER button and then use the UP DOWN button to select channel and adjust
12. th in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect main power before replacement or servicing Make sure there are no flammable materials close to the unit while operating as it is fire hazard Use safety cables when fixing this unit DO NOT handle the unit by its head only always carry by its base Maximum ambient temperature is Ta 40 degrees C DO NOT operate it where the temperature is higher than this Unit surface temperature may reach up to 75 degrees C DO NOT touch the housing with bare hands during its operation Turn off the power and allow about 15 minutes for the unit to cool down before replacing or serving In the event of a serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts 2D DO NOT touch any wire during operation as high voltage may cause electric shock Warning To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture The housing and lenses must be replaced if they are visibly damaged Caution There are no user serviceabl
13. the channel value Once selected press the ENTER button to setup the fixture will run as the channel value indicates Press the MENU button back to the last menu or exit menu mode let the unit idle one minute All channels value will become 0 after exiting Manual Test menu Fixture Information Enter MENU mode select Fixture Information press the ENTER button to confirm use the UP DOWN button to select Fixture use time Lamp On tme or Firmware Version Fixture use time To select Fixture use time press the ENTER button to show the FIXTURE USE TIME on the 10D display Press the ENTER button the fixture working hours will show on the display Press the MENU button to exit Lamp On time To select Lamp On time press the ENTER button to show the LAMP ON TIME on the display Press the ENTER button to confirm then use the UP DOWN button to select Exit or Reset Time press the ENTER button to store Press the MENU button back to the last menu or exit menu mode let the unit idle one minute Firmware Version To select Firmware Version press the ENTER button to show the FIRMWARE VERSION on the display Press the ENTER button and the fixture software version will show on the display Press the MENU button to exit Reset Functions Enter MENU mode select Reset Function press the ENTER button to confirm use the UP DOWN button to select Pan Tilt Zoom or All Pan Tilt To Select Pan Tilt press the ENTER button to show
14. the PAN TILT on the display Use the UP DOWN button to select Yes the unit will run built in program to reset pan and tilt to their home positions or No press the ENTER button to store Press the MENU button to exit menu mode Zoom To select Zoom press the ENTER button to show the ZOOM on the display Use the UP DOWN button to select Yes the unit will run built in program to reset zoom to its home positions or No press the ENTER button to store Press the MENU button to exit menu mode All To select All press the ENTER button to show the ALL on the display Use the UP DOWN button to select Yes the unit will run built in program to reset all motors to their home positions or No press ENTER button to store Press MENU button to exit menu mode Special Functions 11D Enter MENU mode select Special Functions press the ENTER button to confirm use the UP DOWN button to select Fixture Maintenance or Factory Setting Fixture Maintenance To select Fixture Maintenance press the ENTER button to show the FIXTURE MAINTENANCE on the display Use the UP DOWN button to select Interval or Remain Time Interval To select Interval press the ENTER button to confirm the interval time will be shown on the display Press the MENU button to exit Remain Time To select Remain Time press the ENTER button to confirm the remaining time will be shown on the display Press the ENTER button to confirm use the UP DOWN button to select Ex
15. verleaf 5D 001 DMX Address 512 DMX Functions View DMX Value No Yes No Tilt Inverse Yes No P T Feedback Yes No Bl o P T Moving Yes Fixture Settings Red White Balance Blue Auto Cooling Mode Low Linear Square Law Inverse Squ S curve Dimmerspeed Di immer Speed No Display Inverse Yes No Backlight Auto Off Yes Display Setting Backlight Intensity 1 10 T t Unit emperature Uni F No Yes Auto Test Fixture Test Manual Test Exit Reset Time Pan Tilt Reset Functi i Remain Time Special Functions 6D DMxX Functions Enter MENU mode select DMX Functions press the ENTER button to confirm use the UP DOWN button to select DMX Address or View DMX Value DMX Address To select DMX Address press the ENTER button to show the DMX ADDRESS on the display Use the UP DOWN button to adjust the address from 001 to 512 press the ENTER button to setup Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode View DMX Value To select View DMX Value press the ENTER button to show the VIEW DMX VALUE on the display Use the UP DOWN button to view the DMX channel values Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode Fixture Setting Enter MENU mode select Fixture Setting press the ENTER button to confirm use the UP DOWN
16. y chain by XLR plug from the output of the unit to the input of the next unit The cable can not branched or split to a Y cable DMX 512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX output and input connectors are pass through to maintain the DMX circuit when 13D one of the units power is disconnected 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually O amp 1 are equal to 1 6 The end of the DMX 512 system should be terminated to reduce signal errors 7 3 pin XLR connectors are more popular than 5 pin XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin 4 Pin 5 Not used 4 2 Address Setting If you use a universal DMX controller to control the units you have to set DMX address from 1 to 512 so that the units can receive DMX signal Press MENU button to enter menu mode select DMX Functions press the ENTER button to confirm use the UP DOWN button to select DMX Address press the ENTER button to confirm the present address will blink on the display use the UP DOWN button to adjust the address from 001 to 512 and press the ENTER button to store Press the MENU button back to the last menu or let the unit id
Download Pdf Manuals
Related Search