Home
High Point LP Gas Grill
Contents
1. Step 3 Keep children away from the grill During Grilling To avoid tripping safety valves please follow these instructions carefully Step 1 First open lid and turn gas tank on slowly Step 2 Turn only one knob on at a time when lighting up the grill Step 3 Use protective gloves when grill gets hot After Grilling Step 1 Always burn grill for 10 15 minutes to burn off food residues after use Step 2 Wait until the grill is completely cooled before closing lid Step 3 Clean up grease build up to avoid grease fire and cover your grill to prevent rust Please refer to the owner s manual for details DANGER If you smell gas WARNING Do not store or use gasoline or other flammable liquids or vapor in the vicinity of this or any other appliance Shut off gas to the appliance Extinguish any open flame Open lid If odor continues keep away from the appliance and immediately call your gas supplier or your fire department 2 An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance Always read and understand the WARNINGS and INSTRUCTIONS that are contained in this manual before attempting to use this gas barbecue grill to prevent possible bodily injury or property damage NOTE This grill must be used with propane gas only propane gas cylinder not included Always keep this manual for convenient future reference Table of Contents gemi mri TR 3 Illus
2. Assure burner venturi is properly engaged Poor alignment of valve to burner with valve venturi Flame blow out High or gusting winds Turn front of grill to face wind or increase flame height Low on propane gas Replace or refill propane tank Excess flow valve tripped Refer to the Excessive flow safety valve reset procedure on page 14 Flare up Grease buildup Clean grill Excessive fat in meat Trim fat from meat before grilling Excessive cooking temperature Adjust lower temperature accordinalv Persistent grease fire Grease trapped by food buildup knobs to OFF Turn gas OFF around burner system propane tank Leave lid in closed position and let fire burn out After grill cools remove and clean all parts Flashback fire in burner tubes Burner and or burner tubes are Clean burner and or burner tube s locked Inside of lid is peeling like paint The lid is stainless steel not Baked on grease buildup has turned to peeling painted carbon and is flaking off Clean thoroughly Irregular flame Air flow is not correct Correct If flames are yellow or orange open flap Flame blue with yellow tips 1 2 the end of the venturi tubes in high Too little air wavy yellow or 1 8 increments until flames are orange flames Too much air correct noisy blue flames If flames are blue and noisy close flap at the end of the venturi tubes in 1 8 increments until flames are correct Propane M
3. position The burner should light immediately If more than one burner is desired repeat the procedure 2 3 until all desired burners are lit Adjust burners to the desired cooking temperature Precautions After lighting observe the burner flame Make sure all burner ports are lit 2 Ifthe burner flame goes out during operation immediately turn the gas OFF Open lid to let the gas clear for at least 5 minutes before re lighting 3 Before cooking on the grill for the first time and operate the grill for approximately 15 minutes with the lid closed and the gas turned on HIGH This will heat clean the internal parts dissipate odor from the manufacturing process and painted finish 4 Clean the grill after each use DO NOT use abrasive or flammable cleaners This may damage parts of the grill and cause a fire Side Burner 1 Open lid while lighting the burner Lid must remain open while burner is lit 2 Valve must be in the OFF position 3 Open cylinder valve 4 Push side burner knob fully and rotate it slowly about 1 4 turn counterclockwise and then press the igniter promptly The burner should light If the burner does not light turn the knob to the OFF position immediately Wait five minutes for the gas to clear and repeat the procedure 5 Adjust valve knob to the desired cooking temperature Using the Lighting Stick to Light the Side Burner 1 2 Open lid while lighting the burner Lid must r
4. a Insert the pin on the bottom of left door 4 1 into the pre drilled hole on lower left front side of the cart assembly b Push down the pin on the top of left door and insert it into the pre drilled hole on upper left front side of the cart assembly c Repeat the procedure for the right door 4 2 with the right front side of the cart assembly First step Step 5 Install the drawer a Insert the two side rollers of the drawer 5 into the two roller guides on the cart assembly b Push the drawer forward into cart assembly Step 6 Install the body assembly with cart assembly a Put the body assembly 6 on top of the cart assembly b Align the holes on the right side of cart assembly with the holes on the right side of body assembly c Insert one M6 x 20mm bolt A one M6 spring washer D and one M6 washer E into each pre drilled hole d Repeat the procedure with the left side of cart assembly and the left side of body assembly e Go back to tighten all the bolts using the screwdriver provided Pre installed Vf bolts x8 Step 8 Install the valve with side knob and side knob seat a Align the holes on side knob seat 17 with the holes on the right side shelf and side burner valve Screw one M4x12mm bolt F into each pre drilled hole b Tighten the bolts using the screwdriver provided c Insert the side burner knob 18 onto the valve shaft ht 1 Insert the ign
5. Broil Chef WARNING Improper installation adjustment alteration service or maintenance can cause injury or property damage Read the installation operation and maintenance instructions thoroughly before installing or servicing this equipment DANGER Failure to follow these instructions could result in fire or explosion that could cause property damage personal injury or death DANGER DO NOT use gas grill for indoor cooking or heating TOXIC fumes can accumulate and cause asphyxiation DO NOT use in or on boats or recreational vehicles PROP 65 WARNING Chemicals known to the state of California to cause cancer birth defects or other reproductive harm are created by the combustion of WARNING FOR YOUR SAFETY For Outdoor Use Only outside any enclosure High Point LP Gas Grill SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE IF YOU ARE ASSEMBLING THIS UNIT FOR SOMEONE ELSE GIVE THIS MANUAL TO HIM OR HER TO SAVE FOR FUTURE REFERENCE Slc ERY QUESTIONS PROBLEMS MISSING PARTS WITH THIS PRODUCT DO NOT RETURN TO YOUR RETAILER PLEASE VISIT US AT WWW BUILDDIRECT COM YOU CAN ALSO CALL OUR CUSTOMER SERVICE DEPARTMENT 10 00 A M TO 19 00 P M EASTERN STANDARD TIME MONDAY THROUGH FRIDAY AT 1 877 631 2845 Grill Operation 1 2 3 Before Grilling Step 1 Keep your grill a safe distance away from your property Step 2 Always perform a Leak Test on all connections and hoses
6. NFPA54 Reference to Natural Gas and Propane Installation code CSA B149 1 or Propane Storage and Handling code B149 2 IMPORTANT NOTICE READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY AND USE Safety First Read and understand all warnings and precautions prior to operating your grill WARNING 1 This grill is for outside use only It should not be used in a building garage or any other enclosed area 2 use of alcohol prescription or non prescription drugs may impair an individual s ability to properly assemble or safely operate this appliance 3 Always open the grill lid carefully and slowly as heat and steam trapped within the grill could cause severe burns 4 Always place your grill on a hard and level surface far away from combustible materials and structures An asphalt or blacktop surface may not be acceptable for this purpose 5 Do not leave a lit grill unattended 6 Keep children and pets away from the grill at all times 7 This is nota tabletop grill Do not place this grill on any type of tabletop surface 8 Do not use the grill in high winds 9 This grill must be used with propane gas only propane gas cylinder not included 10 Do not attempt to attach this grill to the self contained propane system of a camper trailer motor home or house 11 Do not use charcoal or lighter fluid 12 Do not use gasoline kerosene or alcohol for lighting The LP gas supply cylinder must be constructed and marked in accordance with t
7. am 2 with the holes on the upper left back side of cart assembly 1 b Insert one M6 x 50mm bolt B one M6 spring washer D and one M6 washer E into each pre drilled hole c Repeat the procedure with the right side of back beam and upper right back side of cart assembly d Go back and tighten all the bolts using the screwdriver provided Step 2 Assemble the back panel with cart assembly a Align the holes on the upper right side of back panel 3 with the holes on the upper right back side of cart assembly b Insert one M6 x 15mm bolt C one M6 spring washer D and one M6 washer E into the pre drilled hole c Repeat the procedure with the hole on lower right side upper left side and lower left side of back panel with cart assembly d Go back and tighten all the bolts using the screwdriver provided Step 3 Assemble the spare tank stopper with cart assembly a Align the holes on the left side of spare tank stopper 19 with the holes on the left cart panel b Insert one M6 x 15mm bolt C one M6 spring washer D and one M6 washer E into each pre drilled hole c Align the holes on the bottom side of spare tank stopper 19 with the holes on the cart bottom panel d Insert one M6 x 15mm bolt C one M6 spring washer D and one M6 washer E into each pre drilled hole e Go back to tighten all the bolts using the screwdriver provided Second step Jorane Step 4 Install the doors
8. and warming rack a Place the left heat plates 11 upon the burners b Place the cooking grids 12 upon the heat plates c Place the warming rack 13 on the side walls of fire box Step 13 Install the tank clip and gas tank a Insert the tank clip 14 into the holes on the gas tank seat b Place the gas tank on the tank support and clip it using the tank clip b Connect the tank with regulator by screwing the collar onto the tank valve See diagram to left c Conduct the leak test on page 12 to make certain all connections are connected securely Fully Assembled View Left Side Right Side me mc Nee AE Mr Mv ES ET Qn f D ah an a d EF N ik i B Operating the Grill CAUTION Use only the regulator provided If a replacement is necessary call our customer service center The use of unauthorized parts can create an unsafe condition and environment The propane gas supply cylinder used must be constructed and marked in accordance with the Specifications for Propane Gas Cylinders of the U S Department of Transportation DOT Only cylinders with a listed overfill prevention device OPD and marked propane may be used Cylinders with an OPD will have valve handles with three lobes prongs The pressure regulator and hose assembly supplied with the outdoor cooking gas appliance must be used Replacement pressure regulators and hose assembly mu
9. emain open while burner is lit Remove the lighting stick then insert a match into the end of lighting stick Light the match Once lit place the flame to reach the burner ports See diagram to right Press the control knob and rotate it counterclockwise to the HIGH position The burner should light immediately Adjust burner to the desired cooking temperature Observe flame height when lit Flame should be a blue yellow color between 1 to 2 inches high 13 Confirm that the burner is properly lit and that the flame pattern is as desired see fig A B and C below for the proper flame patterns If the flame pattern is other than normal consult the Troubleshooting on page 16 for corrective action FIG A FIG B FIG C P Normal Soft blue flames with yellow tips Out of adjustment Noisy hard blue Poor combustion Wavy yellow between inch 2 inches high flames too much air flames too little air Burner installation and adjustment overlap Tu p edge face paints up te wo center line 1 Eng edge face upside for install the 1 Release the screw on venturi tube 1 Overlap 14 mm between burner 2 Adjust the flame by turning the collar on head venturi tube and nozzle of venturi tube from back side of the grill and when assembling do not take apart the venturi tube 2 Keep the center line of 3 Tighten the screw and make certain it is venturi tube and nozzle on secured
10. has expired customers will be subject to parts shipping and handling fees Some provinces do not allow the limitation or exclusion of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from province to province If you have any questions related to the product or warranty please visit our website at www builddirect com or call our customer service center at 1 877 631 2845 10 00 A M to 19 00 P M EST Monday through Friday 18
11. he specifications for propane gas cylinders of the U S Department of Transportation DOT CFR 49 13 This outdoor gas appliance is not intended to be installed in or on recreation vehicles and or boats 14 Do not attempt to move the grill while it is lit 15 Do not use the grill unless itis COMPLETELY assembled and all parts are securely fastened and tightened 16 Keep combustible items and surfaces at least 24 inches away from the grill at all times DO NOT use this gas grill or any gas product under any overhead enclosure or near any unprotected combustible constructions 17 Do not use in an explosive atmosphere Keep grill area clear and free from combustible materials gasoline and other flammable vapors and liquids 18 Do not attempt to use or assemble with missing or damaged parts Contact customer service for replacement part CAUTION Prevention of Burns 1 To avoid burns do not touch metal parts of the grill until they have completely cooled for at least 45 minutes or unless you are wearing protective gear such as pot holders protective gloves or mittens 2 Do not alter the grill in any manner 3 Clean and inspect the hose before each use If there is evidence of abrasion wear cuts or leaks the hose must be replaced prior to operation The replacement hose assembly should be in accordance with the manufacturer s specifications 4 Move gas hoses as far away as possible from hot surfaces and dripping hot grease 5 Neve
12. ition cable onto the electrode Step 7 Install the side shelves Loosen the four side panel bolts pre installed on right side of the body assembly and allow 1 4 bolt s length to extend from the body assembly Align the large holes of the right side shelf 8 with the bolts extended from the body assembly Push down on the right side shelf until it locks into place Tighten bolt connections by hand until secure Repeat the same procedure for the left side shelf 7 Go back to tighten all the bolts using the screwdriver provided Step 9 Install the side burner assembly a Open the side burner lid and place the side burner assembly 9 on the right side shelf Make certain the venturi tube is connected properly with valve b Align the holes on the side burner assembly with the holes on the right side shelf c Attached with one M4x12mm bolt F into each pre drilled hole d Insert one M4 washer G one M4 spring washer and one M4 nut into the M4 bolt from underneath by hand e Go back to tighten all the bolts using screwdriver provided f Insert the ignition cable onto the electrode Step 10 Place the side burner grate a Place the side burner grate 10 upon the side burner assembly Step 12 Install the grease cup a Hook the cup support 16 into the grooves beneath the heat insulating plate b Place the grease cup 15 on the cup support 10 Step 11 Install the heat plates cooking grids
13. le unattended to prevent uncontrolled grease fires from erupting Never attempt to move this grill while it is in operation or while it is still hot to prevent possible personal injury Never store or use gasoline or other flammable or volatile substances in the vicinity of this grill or in the vicinity of any other heat generating appliance because of the danger of starting a fire Always confirm that the installation of this grill conforms with the requirements of all local codes or in the absence of applicable local codes with either the National Fuel Gas Code ANSI Z223 NFPA 54 or CAN CGA B149 2 DANGER Gas Safety Liquid propane LP gas is flammable and hazardous if handled improperly Become aware of its characteristics before using any propane product Propane Characteristics Flammable explosive under pressure heavier than air and settles in pools in low areas nits natural state propane has no odor For your safety an odorant has been added Contact with propane could cause freeze burns to the skin his grill is shipped from the factory for propane gas use only Never use a propane cylinder with a damaged body valve collar or footing Dented or rusted propane cylinders may be hazardous and should be checked by your propane gas supplier CAUTION It is essential to keep the grill s valve compartment burners and circulating air passages clean Inspect the grill before each use Step 1 Inspect all h
14. n sparks at crack Wire loose or disconnected No gas flow Coupling nut and regulator not fullv connected Obstruction of gas flow Disengagement of burner to valve Spider webs or insect nest in venturi Burner ports clogged or blocked 16 Prevention Cure Clean wire and or electrode with rubbina alcohol Wipe dry with cloth Replace electrode Reconnect wire or replace electrode wire assembly Check if propane tank is empty If empty replace or refill If propane tank is not empty refer to Excessive flow safety valve reset procedure on page 14 Turn the coupling nut about to three quarters additional turn until solid stop Tighten by hand ONLY do not use tools Clear burner tubes Check for bent or kinked hose Reengage burner and valve Clean venturi Clean burner ports Sudden drop in gas flow or Tank out of gas Check for gas in propane tank reduced flame height Excess flow safety device may Refer to the Excessive flow safety valve have been activated reset procedure on page 14 Irregular flame pattern flame does Burner ports are clogged or Clean burner ports not run the full length of burner blocked Flame is yellow or orange New burner may have residual Burn grill for 15 minutes with the lid closed manufacturing oils 9 Clean venturi Spider webs or insect nest in venturi Clean burner Food residue grease or seasoning salt on burner p
15. n grates have a glass like composition that should be handled with care Use a mild dishwashing detergent or baking soda and hot water solution Non abrasive scouring powder can be used on stubborn stains Rinse with water Heat Plates Clean residue with wire brush and wash with soapy water Rinse with water Grease Cup Periodically empty the grease cup and clean with a dishwashing detergent and hot water solution Cleaning the Burner Assembly Turn gas off at the control knobs and propane tank OD ge IN c Remove cooking grates and heat plate Remove grease cup Remove burner by unscrewing nut from beneath burner foot using a screwdriver and pliers Lift burner up and away from the gas valve orifice Clean inlet venturi tube of burner with small bottle brush or compressed air Remove all food residue and dirt on outside of burner surface Clean any clogged ports with a stiff wire such as an opened paper clip Inspect burner for damage cracks or holes If damage is found replace with a new burner Reinstall burner Make certain the gas valve orifices are correctly positioned pointing straight into burner inlet venturi tube Also check position of spark electrode Problem Burner will not light using Knobs or ianiter Burner will not light using a match Troubleshooting Possible Cause Wires and or electrode covered with cookina residue Electrode and burners are wet Electrode cracked or broke
16. ng the LP tank valve This procedure is effective with all LP Tank sizes as well as Natural Gas When performing the procedure on a Natural Gas model simply substitute Natural Gas valve for LP Tank 14 loensure the procedure is safely and successfully performed please carefully follow these instructions Close the LP tank valve Turn all burner control knobs to the OFF position Disconnect the regulator from the LP tank Open the lid of the grill Turn burner control knobs to HIGH Wait at least 1 minute Turn burner control knobs OFF Wait for at least 5 minutes Re connect the regulator to the LP tank Slowly turn the LP tank valve 1 4 turn at a time and have the valve all the way open With the lid open For grill with ignition button turn on only ONE front burner control knob to the HIGH position Ignite the grill by pushing the ignition button For grill with an automatic ignition Push down the control knob you want to light turn counterclockwise until you hear the ignition click 12 After the first front burner is lit turn on the other control knob s to the HIGH position If you have more than two burners turn them on only ONE AT A TIME 13 When all front burners are lit close the grill lid 14 Wait for 10 15 minutes the temperature should reach 400 450 F WARNING The cylinder valve always has to be above the horizontal position for
17. odels must be open a minimum of 1 8 Natural Gas Models must be open a minimum of 1 16 17 Warranty Program Proof of purchase is required to access this warranty program which is in effect from the date of purchase If unable to provide proof of purchase or after the warranty has expired customers will be subject to parts shipping and handling fees Full 30 Day Warranty Any missing parts can be replaced at no charge within 30 days from the date of purchase with a valid proof of purchase Limited Warranty 10 Years Limited Warranty on stainless steel tube burners 1 Year Limited Warranty on all parts in regards to damage affecting the operation of the gas grill Warranty Provisions This warranty is non transferable and does not cover failures due to misuse or improper installation or maintenance This warranty is for replacement of defective parts only We are not responsible for incidental or consequential damages or labor costs This warranty does not cover chips and scratches of porcelain or painted surfaces nor does it cover corrosion or discoloration due to misuse lack of maintenance hostile environment accidents alterations abuse or neglect This warranty does not cover damage caused by heat abrasive and chemical cleaners resulting in chipped porcelain enamel parts or any damage to other components used in the installation or operation of the gas grill If unable to provide proof of purchase or after the warranty
18. one line WARNING Adjusting the air shutter while the grill is on operation If it is still hot please wear protective gear and be careful Failure to follow this instruction could cause personal injury Flare ups Flare ups sometimes occur when food drippings fall onto the hot heat distribution plate or burners and ignite Some flaring is normal and desirable as it helps impart the unique flavors associated with grilled foods Controlling the intensity of the flare ups is necessary however in order to avoid burned or unevenly cooked foods and to prevent the possibility of accidental fire WARNING Always monitor the grill closely when cooking and turn the flame level down to LOW or OFF if flare ups intensify Shutting Off Burners 1 Always turn the valve knob s clockwise to the HIGH position and then press and turn it to OFF Never force the knob without pressing it This could damage the valve 2 Promptly turn the gas supply to the OFF position at the propane cylinder 3 Close the lid of the grill Excess flow safety valve reset procedure The new regulators are equipped with a safety device that restricts the gas flow in the event of a gas leak However unsafe practices of grill operation could activate the safety device without having a gas leak A sudden shut off of the gas flow typically occurs if you open the LP tank valve rapidly or if one or more of the burner control Knobs is in an open position when openi
19. oses and connections and make certain they are secure Step 2 Check and clean the burner venturi tubes for insects and insect nests by removing the burner and inserting a bottle brush cleaner into each tube to make sure the passage is clear A clogged tube can lead to a fire beneath the grill Step 3 Ensure that the valve nozzle is pointing straight and completely inserted into the venturi tube GENERAL INFORMATION AL 1 A propane gas cylinder is required for operation VENTURI TUBE an P 2 This gas grill is NOT intended for commercial use 4 1 ia Lo s VALVE NOZZLE Illustrated Parts List 2 Back beam 3 Back panel 7 Left side shelf 9 Side burner assembly 1pc a p Fi 19 Spare tank stopper Hardware List M6 x 20mm Bolt M6 x 50mm Bolt M4 Washer p M4 Spring Washer 4pcs MM Screwdriver 1pc M6 Spring Washer M6 Washer Hardware listed above is not scaled to exact size A screwdriver is required on assembly and is included for your convenience Assembly Instructions Remove all contents from the carton packaging Make sure all parts are present before attempting assembly Once the grill is fully assembled go back and check to make certain all the bolts are secure Tighten again using the screwdriver provided if necessary Estimated Assembly Time 40 minutes Step 1 Assemble the back beam with cart assembly a Align the holes on the left side of back be
20. r in the vicinity of another potential heat source 11 Never fill the propane cylinder beyond 80 full This grill is designed to connect to a standard 20 Ib L P cylinder only please refer to the Step 13 of assembly instructions for the installation Warning Don t store spare gas cylinder in or near grill Connecting the Gas Cylinder LP Propane Gas Supply Connection 1 Always place the propane cylinder on the tank brackets located on the right side of the cart 2 Always confirm that all burner control knobs are in the OFF position before activating the gas supply 3 Before connection be sure that there is no debris caught in the head of the gas cylinder head of the regulator valve or in the head of the burner and burner ports 4 Always connect the gas supply regulators as follows Insert the nipple of the valve coupling into the tank valve and tighten the connection collar by turning it clockwise with one hand while holding the regulator with the other hand See diagram to right Disconnect the propane cylinder from the regulator valve when the grill is not in use Do not obstruct the flow of combustion air and ventilation air to the grill Keep ventilation openings of the cylinder enclosure free and clear from debris Place dust cap on cylinder valve outlet whenever the cylinder is not in use Install only the type of dust cap on cylinder valve outlet that is provided with the cylinder valve Other types of caps or pl
21. r keep a filled gas container in a hot car or car trunk Heat will cause the gas pressure to increase which could open the relief valve and allow gas to escape Safe Locations For Use Of This Outdoor Grill DANGER Never use this outdoor grill inside any building garage shed or breezeway or inside any boat trailer or recreational vehicle to prevent a possible fire and to prevent the possibility of carbon monoxide poisoning or asphyxiation WARNINGS Do not use this appliance under overhead combustible surface or covered area e g awnings umbrellas porches or gazeboes Always confirm that this grill is not positioned under the overhang of a house a garage or other structure before lighting it An overhang will serve to deflect flare ups and radiated heat into the structure itself which could result in a fire Always confirm that this grill is positioned more than 24 inches 61 cm away from any combustible materials or surface before lighting it and that no gasoline 24 Inches or other volatile substances are stored in the vicinity of this grill See diagram to right The temperature of a grease fire or of the radiated heat 24 Inches 5 lt might otherwise be sufficient to ignite nearby combustible or volatile substances Always locate this grill where there will be ample combustion and ventilation air dard but never position it in the direct path of a strong wind Never allow the grill to operate whi
22. st be those specified by the outdoor cooking gas appliance manufacturer Use only 20 pound cylinders equipped with a cylinder connection device compatible with the connection for outdoor cooking appliances The cylinder must include a collar to protect the cylinder valve The gas cylinder should not be dropped or handled roughly If the appliance is not in use the gas cylinder must be disconnected Storage of the appliance indoors is permissible ONLY if the cylinder is disconnected and removed from the appliance Cylinders must be stored outdoors and out of the reach of children Cylinder must not be stored in a building garage or other enclosed areas Your cylinder must never be stored where temperatures can reach over 125 F Before connecting make sure there is no debris caught in the head of the gas cylinder regulator valve or in the head of the burner and burner ports Connect regulator valve and hand tighten firmly Disconnect the propane cylinder from the regulator valve when the grill is not in use DO NOT obstruct the flow of combustion air or ventilation air to the grill The propane cylinder must be arranged for vapor withdrawal and equipped with a listed overfill prevention device OPD Danger A fire causing death or serious injury may occur if the following is not followed exactly Never store or use gasoline or other volatile substances in the vicinity of this grill Never store a spare propane cylinder in the vicinity of this grill o
23. the cylinder to have vapor withdrawl only WRONG WRONG WRONG Care and Maintenance IMPORTANT Always allow to completely cool off before covering your grill to prevent corrosion from condensation Caution All cleaning and maintenance should be done when the grill is cool with the fuel supply turned off the control and the propane cylinder disconnected DO NOT clean any grill part in a self cleaning oven The extreme heat will damage the finish Cleaning Burning off the grill after every use approx 15 minutes will keep excessive food residue from building up Clean the grill before and after cooking is recommended Recommended cleaning materials Mild dishwashing liquid detergent Hot water Nylon cleaning pad Wire brush Paper clip Putty knife scraper Compressed air DO NOT use cleaners that contain acid mineral spirits or xylene Outside surfaces Use a mild dishwashing detergent and hot water solution to clean Rinse thoroughly with water 15 Inside surface If the inside surface of the grill lid has the appearance of peeling paint baked on grease has turned to carbon and is flaking off Clean thoroughly with a strong solution of detergent and hot water Rinse with water and allow it to completely dry Interior of grill bottom Remove residue using brush scraper and or cleaning pad Wash with a dishwashing detergent and hot water solution Rinse with water and let dry Cooking Grates The porcelai
24. trated Parts LISTE icon irae once aeo 5 NS 6 ASSEMBLY INSIFUCTIONS aesir a a 7 Operating 11 Connecting Gas CVIIWOOGTE ca coin toco aE 12 c 12 LIGHHMNG E 12 Excess flow safety valve reset procedure 14 Care arid uinci cuis adobe Cucina no Eve ec aedi Cu is eb Cueva cu RUE Ed e 15 THOUDISCSNOOUNG eer E 16 Warranty FO Ol nau eae aa 18 For Your Safety Dear Valued Customer Congratulations on your new barbecue grill purchase You ve made the right choice In this manual you will find assembly instructions suggestions for grilling and helpful hints as well as guidelines for the safe operation proper care and use of your grill Our expert staff strives to provide you with an easy to assemble product Should you have any questions or problems with this product please call our customer service department at 1 877 631 2845 10 00 am 19 00 pm EST Monday through Friday NOTE The use and installation of this product must conform to local codes In the absence of local codes use the National Fuel Gas Code ANSI Z223 1
25. ugs may result in leakage of propane DANGER To prevent fire or explosion hazard when testing for a leak Always perform the leak test on page 12 before lighting the grill and each time the cylinder is connected for use Do not smoke or allow other sources of ignition in the area while conducting a leak test Conduct the leak test outdoors in a well ventilated area Do not use matches lighters or a flame to check for leaks Do not use grill until all leaks have been stopped If you are unable to stop a leak disconnect the propane supply call for gas appliance service or your local propane gas supplier Checking for Leaks 1 Make 2 3 oz of leak solution by mixing one part liquid dishwashing soap with three parts water 2 Make sure control knobs are in the OFF position 3 Spray some solution on the tank valve up to the regulator connection See diagram to right 4 Inspect the solution at the connections for bubbles If no bubbles appear the connection is secure If bubbles appear you have a leak Go to step 6 Disconnect the regulator from the tank and reconnect Make sure the connection is secured Retest with solution If you continue to see bubbles replace the cylinder po NE o gi Danger Failure to open lid while igniting the grill s burners or not waiting five minutes to allow gas to clear if the grill does not light may result in an explosion which could cause serious bodily injur
26. y or death Lighting Your Grill WARNING Never stand with your head directly over the grill when preparing to light the main burners to prevent possible bodily injury Main Burner 1 Open lid while lighting burners WARNING Attempting to light the burner with the lid closed may cause an explosion Make sure there are no 12 en 5 Using the Lighting Stick to Light the Main Burners 1 2 3 obstructions of airflow to the gas unit Spiders and insects can nest and clog the burner venturi tube at the orifice A clogged burner tube can lead to a fire beneath the appliance All valves must be in the OFF position Open cylinder valve Ignite only the burners you wish to use using the same method for each Push desired burner valve knob and rotate slowly about 1 4 counterclockwise until a click is heard The burner should light If the burner does not light return the valve knob to the OFF position immediately Wait five minutes for the gas to clear and repeat the procedure After burner is lit repeat the procedure with any other burner desired Adjust valve knob s to desired cooking temperature Insert a match into the end of lighting stick locked in the drawer Light the match Once lit put the lighting stick through the cooking grid and place the flame next to the burner ports found along the sides of the desired burner See diagram to right Press the valve knob and rotate it counterclockwise to the HIGH
Download Pdf Manuals
Related Search
Related Contents
iTNC 530 - The Versatile Contouring Control for Milling ETC情報を利用する MANUAL DE USUARIO - Ministerio del Trabajo 参考資料1-6 蓄電池設備の点検 G3 Ferrari Silver 28 WaterTechw² Redox8000 Sensor Instruction Michel BALLARD - Université d`Artois Copyright © All rights reserved.