IMPORTANT Please make certain the persons who
Contents
1. completely Replace the generator on a level surface Add engine oil to the upper level Install the oil filler cap Install the cover and tighten the screw Recommended engine oil see page 5 Above SJ Grade CAUTION Besurenoforeign material enters the crankcase ero o Do not tilt the generator when adding engine oil This could result in overfiling and damage to the engine Clean the oll filter every 100hr 3 AIR FILTER Maintaining the air filter in proper condition is very important Dirt induced through improper installation or improperly servicing of the air filter will wear out the engine Keep the air filter element always clean 1 Remove the cover 2 Remove the air filter cover and element 3 Wash the element in solvent and dry 4 Oilthe element and squeeze out excess oil The element should be wet but not dripping 5 Insert the element into the air filter 6 Install the cover CAUTION The engine should never run without the element excessive piston and or cylinder wear may result 4 CLEANING AND ADJUSTING SPARK PLUG 10 1 Remove the cover 2 Check for discoloration and remove the carbon 3 Check the spark plug type and gap 4 Install the spark plug 5 _ Install the cover Standard electrode color Tan Color Standard Spark Plug CRAHSB NGK Spark Plug Gap 0 6 0 7 mm 0 024 0 028 in 5 FUEL TANK FILTER 1 Remove the fuel tank cap and filter 2 Clean the filter2. AUTO THROTTLE switch is tumed to ECO the economy control will adjust the engine speed according to the connected load The results are better fuel consumption and less noise 4 FUEL TANK CAP AIR VENT KNOB The fuel tank cap is provided with an air vent knob to stop fuel flow The air vent AUTO THROTTLE knob must be turned once counterclockwise from the closed position This will allow fuel to flow to the carburetor and the engine to run When the engine is not in use tighten the air vent knob clockwise until it is finger tight to stop fuel flow 5 FUELCOCK The fuel cock is used to supply fuel from the tank to the carburetor 3 PRE OPERATION CHECK NOTE Add more than 2 liters of fuel to run this machine for the first time Pre operation checks should be made each time the generator is used 1 CHECK ENGINE FUEL Make sure there is sufficient fuel in the tank If fuel is low refill with unleaded automotive gasoline Be sure to use the fuel filter screen on the fuel filter neck Recommended fuel Unleaded gasoline Fueltank capacity 5 7 liters WARNING Donotrefil the generator while the engine is running or hot Close fuel cock before refueling the generator Becarefulnotto allow dust dirt water or foreign objects into the fuel Donotfil above the top of the fuel filter or the fuel may overflow when the 2 CHECK ENGIN
3. require other grounding specifications For this purpose please use the ground wire that attaches from the frame to the generator unit Using a No 12 AWG American Wire Gauge stranded copper wire to the frame and to an earth driven copper or brass grounding rod provides sufficient safety against shock However local codes may differ Contact a local electrician to find out specifications for grounding your generator 5 CONNECTION NOTES Avoid connecting the generator to commercial power outlet Avoid connecting the generator in parallel with any other generator 2 CONTROL FUNCTION DESCRIPTION 1 Engine switch 2 Auto throttle 4 Spark plug 5 Muffler 7 Choke lever 8 AC receptacle L14 30R 10 AC receptacle 5 20R GFCI 11 AC protector 20A 13 Overload light 14 Output light 16 Fuel tank cap 17 Recoil starter 19 Oil filler cap 20 Air filter cover 1 OIL WARNING SYSTEM 19 20 When the oil level falls below the low level line the engine wil Stop automatically Unless you refill with oil the engine will not start again 2 ENGINE SWITCH The engine switch controls the ignition system 3 Fuel tank 6 Carrying handle 9 Ground earth terminal 12 Oil alert light 15 Fuel filter 18 Fuel cock On Ignition circuit is switched on The engine can be started Ignition circuit is switched off The engine will not run 3 AUTO THROTTLE When the
4. with solvent If damaged replace 3 Wipe the filter and insert it WARNING Be sure the tank cap is tightened securely 6 MUFFLER SCREEN WARNING The engine and muffler will be very hot after the engine has been running Avoid touching the engine and muffler while they are still hot with any part of your body or clothing during inspection or repair 1 Remove the cover Remove the muffler screen Use a flathead screw driver to pry the spark arrester out from the muffler A oO m Remove the carbon deposits on the muffler screen and spark arrester using a wire brush 5 _ Install the muffler screen 6 _ Install the cover 11 6 TROUBLE SHOOTING 1 Engine will not start 1 Fuel system No fuel supplied to the combustion chamber No fuel in tank Supply fuel Fuel in tank Fuel tank cap air vent knob to ON fuel cock knob to ON Clogged fuel line Clean fuel line Clogged carburetor Clean carburetor Engine oil system Insufficient Oil level is low Add engine Electrical systems Poor spark Sparkplugis dirty with carbon deposit or it may be wet Remove carbon or wipe the spark plug dry Faulty ignition system Consult dealer 4 Compression is insufficient Wom out piston and cylinder Consult dealer 2 Generator won t produce power Safety device AC to OFF Stop the engine then restart Safety
5. E OIL Make sure the engine oil is at the upper level of the oil filler hole Add oil as necessary 3 GROUND Earth Make sure to ground earth the generator 4 OPERATION NOTE 1 STARTING THE ENGINE NOTE fuel heats up and expands Wipe off spilt fuel thoroughly before starting engine Keep open flames away Remove oil filler cap and check the engine oil level SAE 10W If oil level is below the lower level line refill with suitable oil to upper level 10w 30 or 10W 40 SAE 20 or 10W 30 or 10W 40 SAE 30 or 10W 30 or 10W 40 line Do not screw in the oil filler cap when checking oil level Change oil if contaminated Oil capacity 0 9 liters Recommended engine oil The generator has been shipped without engine oil Fill with oil or it will not start Before starting the engine do not connect electrical loads Tum the economy control switch to the OFF position 5 3218 80 ENGINE SWITCH SN OFF a amp m 6 7 8 2 USING ELECTRIC POWER 1 Check the AC pilot lamp for proper voltage b Tum the economy control switch to the ON position c Tum off the switch es of the electrical appliance s before connecting to d Insert the plug s of the electrical appliance s into the receptacle s CAUTION 2 OVERLOAD INDICATOR LIGHT The overload indicator light comes on when an overload of a connected electrical device
6. Eastem Tools amp Equipment Inc must warrant the emission or evaporative control system on your small nonroad engine for the periods of time listed above listed above provided there has been no abuse neglect or improper maintenance of your small nonroad engine Your emission or evaporative control system may include parts such as the carburetor or fueHinjection system the ignition system and catalytic converter Also included may be hoses belts connectors and other emission or evaporative related assemblies Where a warrantable condition exists Eastem Tools amp Equipment Inc will repair your small nonroad engine at no cost to you including diagnosis parts and labor OWNER S WARRANTY RESPONSIBILITIES As a small non road engine owner you are responsible for the performance of the required maintenance listed in your Owner s Manual Eastem Tools amp Equipment Inc recommends that you retain all receipts covering maintenance on your small nonroad engine but Eastern 18 Tools amp Equipment Inc cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance As the small non road engine owner you should however be aware that Eastem Tools amp Equipment Inc may deny you warranty coverage if your small non road or part thereof has failed due to abuse neglect improper maintenance or unapproved modifications Youare responsible for presenting yo
7. IMPORTANT Please make certain the persons who are using the equipment thoroughly read and understand the user s manual prior to operation CONTENTS 1r SA FETY IN FO RMATI N cee cee cee cee eee eoe coe eoe coe oeo L F U N C TI N coe cee cee eoe coe ese seo oce ceo ooe soo ooe coe ooo eoe oee coe PRE PERATI C HE C K cee cee cee cee cee coe coe ese seo eoe see eoe see eoe ooe coo cee 7 PERATI N cee cee cee cee eee coe oeo eoe oeo eoe ooe oeo eoe oeo eoe ooo coo eoe oeo eoe ooe ceo PERIODIC MAINTENANCE eee eso coe soe soo ooo ooe ooo ooo ooo ooo ooe ooo ooo ooo TR U BLE S H OT IN G ese ese ooe ooe ooe ooe ooe ooe ooe ooe ooe ooe ooo ooo ooo ooo ooo ooo S T G E cee cee cee coe eoe eoe coe oeo ooe eoe oeo cee coe eoe ceo oeo ooe eoe soo oeo ooe eoe S PE C I FI C ATI 5 Pee see ooe ooo sos ooo ooo soo coo ooo soo ooo ooe ooo ooo ooo ooo soo ooo 10 WIRIN G DI AG RAM cee cee cee cee coe cee cee sos oso eoe seo eoe oeo soe soo ooo eoe oeo cO N O WARNING PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE OPERATING THE MACHINE c no 12 13 14 15 1 SAFETY INFORMATION 1 EXHAUST FUMES ARE POISONOUS Never operate the engine in a closed area because it may cause unconsciousness and death within a short time Operate the engine in a well ventilated area 2 FUELIS HIGHLY FLAMMABLE AND POISONOUS Always tum off the engine
8. SUMER COMMERCIAL USE USE USE USE GASOLINE 1 year 90 days 1 year 90 days GENERATOR The warranty period begins on the date of purchase by the first retail consumer or commercial end user and continues for the period of time stated in the table above Consumer use means personal residential household use by a retail consumer Commercial use means all other uses including the commercial income producing or rental purpose the engine has experienced commercial use it shall thereafter be considered as a commercial use engine for purpose of this warranty Engines use in competitive racing or commercial or rental tracks are not warranted A two year warranty applies to the emission control system on engines certified by EPA and CARB IMPORTANT WARRANTY REGISTRATIONS IS NECESSARY TO OBTAIN LIMITED WARRANTY ON EASTERN 16 TOOLS amp EQUIPMENT INC ENGINES THE WARRANTY REGISTRATION CARD MUST BE RETURNED WITHIN 15 DAYS OF PURCHASE FOR LIMITED WARRANTY TO BE VALID About Your Product Warranty Eastem Tools amp Equipment Inc welcomes warranty repair and apologizes to you for being inconvenienced Authorized Service Dealer may perform warranty repairs Most warranty repairs are handled routinely but sometimes warranty service may be inappropriate For example warranty would not apply if an engine is damaged because of misuse lack of routine maintenance shipping handling war
9. d Both the ECS Warranty and the Eastem Tools amp Equipment Inc product Warranty describe important right and obligations with respect to your new engine Eastem Tools amp Equipment Inc at its location in Ontario Califomia can perform warranty service or any authorized service dealer near you At the time of requesting warranty service evidence must be presented of the date of sale to the original purchaser The purchaser shall pay any charges for transporting the product to and from the place when the inspection and or warranty preformed The purchaser shall be responsible for any damage or loss incurred in connection with the transportation of any engine or any part s thereof submitted for inspection and or warranty work If you have any questions regarding your warranty rights and responsibilities you should contact Eastem Tools amp Equipment Inc 19 PRODUCT REGISTRATION For more efficient customer service please fill out the information below and mail to Eastern Tools amp Equipment Inc Product Warranty and Registration Division Model No Engine Serial No Purchase Date Purchased from Retail Location Private Consumer Other Name Location Address Telephone Purchase Price Purchased New Used Consumer Information Name Telephone Street Address Suite or Apt No City State Zip Code Province or County Are you a Business Res
10. d or workmanship only and not replacement or refund of the equipment to which the engine may be mounted Nor does the warranty extend to repairs required because of 1 Problems caused by parts that are not original eastem tools amp equipment inc parts 2 Equipment controls or installations that prevent starting cause unsatisfactory engine performance or shorten engine life Contact equipment manufacturer 3 Leaking carburetor clogged fuel pipes sticking valves or other damage caused by using contaminated or stale fuel Use clean fresh lead free gasoline 4 Parts which are scored or broken because an engine was operated with insufficient or contaminated lubricating oil or and incorrect grade of lubricating oil check oil level daily or after every 8 hours of operation Refill when necessary and change 17 at recommended intervals Engine damage may occur if oil level is not properly maintained Read Operating amp Maintenance Instructions 5 Repair or adjustment of associated parts or assemblies such as clutches transmissions remote controls etc which are not manufactured by Eastem Tools amp Equipment Inc 6 Damage or wear to parts caused by dirt which entered the engine because of improper air filter maintenance re assembly or use of a non original air filter element or cartridge Read Operating amp Maintenance Instructions 7 Parts damaged by over speeding or overheating caused by grass debris or dir
11. device DC to OFF Press to reset DC protector button 7 STORAGE Long term storage of your machine will require some preventive procedures to guard against deterioration 1 DRAIN THE FUEL 1 Remove the fuel tank cap drain the fuel from the fuel tank 2 Remove the cover drain the fuel from the carburetor by loosening the drain screw 2 ENGINE 1 Remove the spark plug pour in about one tablespoon of SAE 10W30 or 20W40 motor oil into the spark plug hole 12 2 m and reinstall the spark plug Use the recoil starter to tum the engine over several times with ignition off Pull the recoil starter until you feel compression Stop pulling Clean exterior of the generator and apply a rust inhibitor Store the generator in a dry well ventilated place with a cover placed over it The generator must remain in a vertical position 13 9 SPECIFICATION MODEL IN3500i Type Inverter Generator m AC Voltage 120V q Frequency 60Hz Max Output 3500 Watts Rated Output 3000 Watts Power Factor 10 Model XY157F Type Air cooled 4 cycle OHV Gasoline Engine Bore X Stroke 57 57 8 Displacement 149 5 cc Max Output 4 0KW 5500rpm Fuel Regular Automobile Gasoline 5 Fuel tank Capacity 1 5 gallons Rated Continuous Operation 3h5min 100 Load 4h10min 50 Load Lubricating oil SAE 10W30 Lubricating oil Capacity 0 90 l
12. ehousing and improper installation Similarly warranty is void if the serial number on the engine has been removed or if the engine has been altered or modified If a customer differs with the decision of the Service Dealer an investigation will be made to determine whether the warranty applies Ask the Service Dealer to submit all supporting facts to his Distributor or the factory for review If the distributor or the factory decides that the claim is justified the customer will be fully reimbursed for those items that are defective avoid misunderstanding which might occur between the customer and the dealer listed below are some of the causes of engine failure that the warranty does not cover Normal wear Engines and generators like all mechanical devices need periodic parts service and replacement to perform well Warranty will not cover repair when normal use has exhausted the life of a part of an engine Improper maintenance The life of an engine or your equipment depends upon the conditions under which it operates and the care it receives Some applications such as tillers pumps and rotary mowers are very often used in dusty or dirty conditions which can cause what appears to be premature wear Such wear when caused by dirt dust spark pug cleaning grit or other abrasive material that has entered the engine because of improper maintenance is not covered by warranty This warranty cover engine related defective material an
13. idence Product Usage Information How often will you use this product Everyday Periodically Emergency Use Only Other What type of application will you use this product in Heavy Commercial Moderate Commercial Light Commercial Tradeshows Heavy Residential Moderate Residential Light Residential Camping Backpacking Other Important information It is critical to your warranty that the original point of sales receipt the retained by current consumer and in order to comply with Eastern Tools amp Equipment Product Warranty statement you must return the registration card within 15 days of original purchase Product warranty is valid from original date of purchase Please mail the above card to Eastern Tools amp Equipment Inc 111 Bluegrass Dr Norwalk OH 44857 Mail Eastern Tools amp Equipment Inc 600 Industrial Way Norwalk OH 44857 Telephone 1 888 908 6200 Website www eastemtools com 20 21
14. is detected the inverter unit overheats or the AC output s e fees voltage rises The electronic breaker will then activate stopping power to the ap generation in order to protect the generator and any connected electric devices The AC pilot light green will tum off and the overload indicator light red will the generator Open the fuel tank air vent to the ON position Tum the fuel cock lever to the ON position Tum the engine switch to the ON position Tum the choke lever to the position Not necessary if the engine is wa Pull the starter handle slowly until resistance is felt This is the Compression point Retum the handle to its original position and pull swiftly Do not fully pull out the rope After starting guide the starter handle to its original position while still holding the handle Grasp the carrying handle firmly to prevent the generator from falling over when pulling the recoil starter Warm up the engine Tum the choke lever back to the operating position Warm up the engine without a load for a few minutes AC APPLICATION doc WINE Be sure the electrical load is tumed off before plugging it in Be sure the total load is within the generator rated output Be sure the socket load current is within socket rated current The AUTO THROTTLE switch must be tumed to HIGH when using electric devices that require a la
15. iter Starting System Recoil Starter Ignition system 1 Spark Plug ATRTC or CRBHSB NGK Netdimension LXWXH 565 320 470 Overalldimension LXWXH 595 355 X 510 Gross Weight 69 4 pounds NetWeight 65 pounds Specifications subject to change without prior notice 14 10 WIRING DIAGRAM R R BL BL BL Protector 20A esd LH 0 ii 0 BLI d Math fess aloo TSH Poi BL e V J BU BU E 4 Stepping motor BL BL BL BL R e Re j you Economie 3 switc abe pepe I t E M BL BL nver E roy px BL y BL Main xS cell Y winding a BU Working roa a GR indicator s C W NE BL e M Overload control Y G indicator gt winding WOI IBL 20 Ve gt De lt Lo BU Low oil indicator Spring winding y PU rea Engine t BL Iz switch AC27V winding ae C gt QL SENSCR BLACK r BROWN Bu BLUE R RED ron W Spark G GREEN y WHITE m plug Y EET T Ignition r 4 BU STE Y YELLOW 0 ORANGE je R 1 High PU PURPLE Y G YELLOW GREEN equipment Y m TUE per t press
16. k cap air vent knob clockwise until it is finger tight ed 5 PERIODIC MAINTENANCE 1 MAINTENANCE CHART Regular maintenance is most important for the best performance and safe operation Every 12 months Clean Replace if necessary Check oil level Replace il Oil filter Clean oil filter Air Filter Clean Replace if necessary Fuel Filter Clean fuel cock filter Replace if necessary Oekmewen e _ Valve Check and adjust when engine d e Clearance iscold FuelLine Check fuel hose for cracks or Pe f damage Replace if necessary Exhaust Check for leakage Retighten or replace gasket if necessary Check muffler screen Clean replace if necessary Carburetor Checkchoke operon Cooling Check fan damage system Stating Checkrecnistateroperin e d T 8 C MU ee Megex Cheandaciustengreidesee Fitings Check all fittings and fasteners Fasteners correct if necessary Crankcase Check breather hose for cracks or breather damage Replace if necessary 2 ENGINE OIL REPLACEMENT Place the machine on a level surface and warm up the engine for several minutes Ther cock knob to OFF Tum the fuel tank cap air vent knob clockwise 1 Loosen the screw and remove the cover 2 Remove the oil filler cap 3 Place an oil pan under the engine Tilt the generator to drain the oil
17. rge starting current such as a compressor or a submergible pump AUTO THROTTLE HIGH 6 tum on but the engine will not stop running As the engine overloads the overload indicator light red with tum on Allowing you to tum off the power too appliances After twenty seconds the overload indicator light will tum off and the generator will begin to run again If the generator is still overloaded the overload indicator light with tum on once again If this process happens a total of three times the engine will completely tum off If so please follow the following steps a Tum off any connected electric devices and stop the engine b Reduce the total wattage of connected electric devices within the application range c Check for blockages in the cooling air inlet and around the control unit If any blockages are found remove d After checking restart the engine CAUTION The generator AC output automatically resets when the engine is stopped and then restarted The overload indicator light may come on for a few seconds at first when using electric devices that require a large starting current such as a compressor or a submergible pump However this is not a malfunction 3 STOPPING THE ENGINE 1 Tum off the power switch s on electrical loads or disconnect any electric devices 2 Tumthe engine switch to OFF position ON 3 Tum the fuel cock lever to OFF E AME ae SWITCH 4 Tum the fuel tan
18. t which plugs or clogs the cooling fans flywheel are or damaged caused by operating the engine in a confined area without sufficient ventilation 8 Engine or equipment parts broken by excessive vibration caused by a loosen cutter blades unbalanced blades or loose unbalanced impellers improper attachment of equipment to engine crankshaft over speeding or other abuse in operation 9 Abentorbroken crankshaft caused by striking a solid object with the cutter blade of a rotary lawn mower or excessive v belt tightness 10 Routine tune up or adjustment of the engine 11 Engine or engine component failure i e combustion chamber valves valve seats valve guides or bumed starter motor winding caused by the altemated fuels such as liquidfied petroleum natural gas altered gasoline etc Warranty is available only through service dealers which have been authorized by Eastem Tools amp Equipment Inc please contact the place of purchase or Eastern Tools amp Equipment Inc for a Service Dealer near you CALIFORNIA amp USEPA EMISSION OR EVAPORATIVE CONTROL WARRANTY The U S Environmental Protection Agency EPA the Califomia Air Resources Board CARB and Eastem Tools amp Equipment Inc are pleased to explain the Federal and Califomia Emission Control System Warranty on your small non road engine Califomia new small nonroad engines must be designed built and equipped to meet the State s stringent and anti smog standards
19. ur small non road engine to Eastem Tools amp Equipment Inc distribution center as soon as a problem exists warranty repairs should be completed in a reasonable amount of time not to exceed 30 days If you have any questions regarding your warranty rights and responsibilities or request warranty service you should contact either the place of purchase or Eastem Tools amp Equipment Inc c o Service Manager Engine and Equipment Service Division IMPORTANT NOTE This warranty statement explains your rights and obligations under Emission Control system Warranty ECS Warranty which is provided to our by Eastem Tools amp Equipment Inc pursuant to Califomia law Eastem Tools amp Equipment Inc also provides to original purchasers of new Eastem Tools amp Equipment Inc engines Tools amp Equipment Inc Limited Warranties for New engines amp other Equipment associated with the engine Eastem Tools amp Equipment Inc Products Warranty which is enclosed with all New Eastem Tools amp Equipment Inc engines and products on a separate sheet The ECS Warranty applies only to the emission or evaporative control system of your new engine To the extent that there is any conflict in terms between the ECS Warranty and the Eastem Tools amp Equipment Inc Warranty the ECS Warranty shall apply except in any circumstances in which the Eastem Tools amp Equipment Inc Product Warranty may provide a longer warranty perio
20. ure Gr GRAY A AZURY mT lye LI wrap PINK ESA R LIMITED WARRANTY Eastem Tools amp Equipment Inc wil repair or replace free of charge any part or parts of the generator that are defective in material or 15 workmanship or both Transportation charges on parts submitted for repair or replacement under this Warranty must be bome by purchaser This warranty is effective for the time period and subject to the conditions provided for in this policy For warranty service find the nearest Authorized Service Dealer by contacting the place of purchase or Eastem Tools amp Equipment Inc THERE IS NO OTHER EXPRESSED WARRANTY IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR FROM PURCHASE OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED LIABILITY FOR CONSEQUENTIAL DAMAGES UNDER ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation and exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Eastem Tools amp Equipment Inc WARRANTY PERIOD WITHIN U S A AND CANADA OUTSIDE U S A AND CANADA ENGINES CONSUMER COMMERCIAL CON
21. when refueling Never refuel while smoking or in the vicinity of an open flame Take care not to spill any fuel on the engine or muffler when refueling If you swallow any fuel inhale fuel vapor or allow any fuel to get in your eyes see your doctor immediately If any fuel spills on your skin or clothing immediately wash with soap and water and change your clothes When operating or transporting the machine be sure it is kept upright If tilted fuel may leak from the carburetor or fuel tank 3 ENGINE AND MUFFLER MAY BE HOT Place the machine in a place where pedestrians or children are not likely to touch the machine Avoid placing any flammable materials near the exhaust outlet during operation Avoid operating the engine with a dust cover e e Keepthe machine atleast 1 m 3 ft from buildings or other equipment or the engine may overheat e Be sure to cany the generator only by its handle e Put the machine on a flat surface This will allow the machine to 4 p distribute the heat evenly 4 ELECTRIC SHOCK PREVENTION cool air Never operate the engine in rain or snow Nevertouch the machine with wet hands or electrical shock will occur Besureto ground earth the generator The National Electric Code requires that the frame of generator and the extemal electrically conductive parts of the generator be connected to an approved earth ground Local codes may differ and
Download Pdf Manuals
Related Search