VS-540-HDSDI User Manual ver.1.0
Contents
1. Live View ip Change User m View Size X12 X1 X2 4 El Video Server Kn The configurations are grouped into 10 categories System Video Audio Network Serial Event Preset Record User and Camera Any configuration changes are not applied until the Apply button is pressed Leaving the page without pressing Apply button any changes in the page will be discarded 2 0 Megapixel IP Camera Manual 17 51 VS 540 HDSDI User Manual System Configuration Setup Live View Change User System Video Audio Network Serial Event Preset Record User Camera system General oystem ID TCAM 540 X18H Language English w Apply Firmware Version Enc 1 1020 026 Board ID 75 CT d dou Firmware Upgrade Time start Time 2010 06 01 17 17 20 Current Time 2010 06 01 21 27 10 Time Format Y Y MMOD hh mm ss v Time Zane Gh4T 12 00 International Date Line S Vest Automatically synchronize with NTP server NTP Server Name O pool ntp org Reboot Factory Reset Factory Reset 2 0 Megapixel IP Camera Manual 18 51 TVS 540 HDSDI User Manual General e System ID Enter the System ID to be used as a camera title The set System ID is displayed with video image on Web Browser The System ID is also transferred to remote software such as CMS and displayed on it Language Select the language to be used for web based configuration Firmware e Firmware version Dis2. Day Color Delivers a color image regardless of light Night B W Delivers a B W image regardless of light White Balance e White Balance has the following modes Auto This mode computes the white balance value output using color information from the entire screen It outputs the proper value using the color temperature radiating from a black subject based on a range of values from 3000 to 7500K Manual Manualy controls the R and B gain 256 steps each 1 3 Megapixel IP Camera Manual 50 51 VS 540 HDSDI User Manual Auto Exposure e AE Mode ETC Full Auto Auto Iris and Gain Fixed Shutter Speed 59 94 NTSC 1 60 sec 50 PAL 1 50 sec DSS Digital Shutter Speed mode Auto or Off can be selected When DSS mode is Auto from 1 2 to 1 60 DSS Limit is available Back Light Compensation can be selected Manual 21 steps of Shutter 18 steps of Iris and 8 steps of Gain can be set manually Shutter Priority 21 steps 1 2 1 10 000 of Shutter Speed can be set manually The Iris and Gain are set automatically according to the brightness of the subject Iris Priority 18 steps F1 8 to Close of Iris can be set manually The Shutter Speed and Gain are set automatically according to the brightness of the subject Bright The bright control function adjusts both the Gain and lris using an internal algorithm according to a brightness level set by user Exposure is controlled by Gain when dark and by iris when brig
3. Be sure to restart the system after inserting an SD Card During booting the system reads the status of the disk and initializes it Once the initialization of a disk is finished the status of the disk is shown on the Record page of web based setup e Disk Information Setup Live View Change User System Video Audio Network Serial Event Preset Record User Record Apply search Page Disk Information Memory stick detected Disk Size 0 96 G Free Space 0 96 G The status of a disk can be checked from the Disk Manage menu of True Manager as well Disk Manage Address 192 168 10 77 System ID Video Server Model TCS 200 Type Encoder Firmware Version Encoder V1 TO50 Disk Status USB Disk available Disk Size 232 88 G Free Space 172 85 G Disk Format 2 0 Megapixel IP Camera Manual 40 51 VS 540 HDSDI User Manual Refer to the chart for checking the status of disk Nodsk 0 Disk is not connected to the system Searching Disk information Checking the status of disk Refresh the page and wait until the status is changed Mounting and Performing recovery process when disk damage is found It takes from seconds to minutes for recovering Recovering Disk Disk format needed Disk is attached but the type of the file system is unknown or damaged Unknown disk type detected USB or SD Disk available Disk is available but formatting is recommended
4. al s e aaa 13 Remote Video Monitoring ME 13 INITIAlIZAUON OT IP e ele 16 4 Remote Configura OM sas ak aaa dana ia aan E a An KE OTT 17 ISING GD siio aaa aaa aan an na gina aapa Nk aa aga kata IN Ka pa pai kaa Ta pa ya ak aa Wa E 17 System Configuration ee a ee 16 VIdeo Ne Tu ele Lee karana aaa waga a Eng a E a UN BA MA WA a KA BA MAN a Ba UIN Tg ENE ee ne 22 Audio OCI en PERENNE ee 27 NEO COMIC UP AMOI BE 28 oeral OMI UN ANNO NE ETE OE DO TODO TTE 33 EVEN CONTOUR AION RE T EDT DT ETT 35 F FOS ONC ORIG AO omm 38 RECON CONNUT O ht EET 39 Brauerei RE 48 Camera COMMNGUY ANON MEN TR T 50 2 0 Megapixel IP Camera Manual 3 51 VS 540 HDSDI User Manual 1 Introduction About this manual This User Manual provides information on operating and managing the premium network camera VS 540 HDSDI The Manual includes instructions of installation operation and configuration of VS 540 HDSDI as well as how to make troubleshooting Features VS 540 HDSDI is a 2 0M network based camera with remote live monitoring audio monitoring and control via an IP network such as LAN ADSL VDSL and Wireless LAN Camera Audio Network 1 3 CMOS Image Sensor X10 optical zoom X12 digital zoom True Day amp Night ICR Highly efficient compression algorithm H 264 amp MJPEG support Resolutions CIF 352x240 Full HD 1920x1080 Wide range of transmission rates 32kbps 8Mbps Various transmis
5. 3 A3 00 04 00 1C 63 43 05 57 O0 1C 63 43 05 27 00 1C 63 43 05 60 Model TCS 200 TCS 20 TCS 200 TCS 200 Type Encoder Encoder Encoder Encoder Firmware Encoder V1 T046 Encoder V1 T047 Encoder V1 TO47 Encoder V1 1021I Start Up Time 2008 03 12 15 57 26 2008 03 12 16 09 55 2000 01 12 14 44 47 1999 12 31 12 11 37 Disk Manage Address 192 168 10 89 System ID Video Server Model TCS 200 Firmware Version Encoder V1 T046 Disk Status USB Disk available we 76 69 G 41 11 G Type Encoder Disk Size Free Space Disk Format While formatting a disk the progress will update in the Disk Status field The system may be rebooted depending on the situation Once the USB Disk available is displayed it means that formatting has completed successfully Once formatting is started it is not allowed to cancel Even if you close the Disk Manage dialog box formatting will continue 2 0 Megapixel IP Camera Manual 46 51 VS 540 HDSDI User Manual Trouble Shooting There may be damage in the file system if you turn off the power of VS 540 HDSDI or remove the SD memory card while any data is being written For FAT32 recording in not possible if the file system is damaged If this happens the SD card should be reformatted on the PC For EXT3 if the damage to the file is not serious it can be automatically recovered The recovery is executed at the initialization of the syst
6. D SDI video may contain errors if the correct type of BNC coaxial cable is not used If the video transmission distance exceeds 100 meters video data may lost due to a reduction in the video signal In order to prevent this use of a repeater is recommended e When using HD SDI video can be only be viewed on a HD SDI monitor Connecting Audio Audio is full duplex It is possible to set the mode as Tx only Rx only or Tx Rx 1 Connect the audio input and output ports to corresponding audio devices 2 The Audio signal required is line level Audio equipment using an amp mixer or other amplifier should be used 2 0 Megapixel IP Camera Manual 11 51 VS 540 HDSDI User Manual Connecting Serial Port RS 485 Communication e RS 485 of VS 540 HDSDI can be connected to external equipment such as a PT receiver etc The PC client can send PT commands to the external equipment via the serial port When a decoder system instead of PC client is connected to VS 540 HDSDI the serial port and that of the decoder system works in pass through mode That is data from at one port is delivered to the other port and vice versa Connecting Sensor and Alarm Connect sensor and alarm devices to corresponding terminals accordingly Check if it works Once the power is supplied to the camera it will start booting The system will boot up to an operating mode after approximately 40 60 seconds The green LED on the Ethernet port will flash indicat
7. E mail LIFTP No Preset Duration x 4 Alarm synchronous E mail Notification Serer Address Port 25 j Sender Address Authentication on SMTP server WON O On ID Password Destination Address Video Clip Attaching 9 Off Primary Video Secondary Video OJPEG Capture Number of Frame ft 10 E mail Test Before testing e mail please apply your configuration first FTP Upload server Address Port 21 Password Upload Video 9 Primary Video Secondary Video O JPEG Capture Number of Frame 1 10 Continuous Upload Off On Upload Duration 10 sec Max 300 Upload Interval 300 sec Max 3600 Event Record Pre event Time None Post event Time None 2 0 Megapixel IP Camera Manual 35 51 VS 540 HDSDI User Manual When a decoder instead of a PC client is connected to a VS 540 HDSDI one system becomes a Local system and the other a Remote system Generally a system which is being used by the user is called as Local system Then actions for events can be configured for events from the remote system as well as for local system For example it is possible to turn on an alarm device in local center decoder system when a sensor device in remote site IP camera is triggered Local section configures the actions for events from local self system and configuration activates local devices Remote sections configure the actions for events from the remote peer sys
8. It is also not allowed to download two AVI files at the same time Delete f you want to delete recorded files select the files by checking the box in front of each file and press the Delete button Root gt gt 2008 03 03 L File Name Size o 080303 165722 165731 avi 130 M oO 080303 165355 165608 avi 2251 M Inl 080303 165143 165213 avi 448 M om in 4 ee Itis possible to delete multiple files at once 2 0 Megapixel IP Camera Manual 45 51 VS 540 HDSDI User Manual Format disk True Manager is used to format the SD card which is inserted in the system After connecting True Manager to a system choose Disk Manage on the Tools menu DER Group Server I Groups All Servers e test Ping Test Network Test System Test Log Reboot d Optians bd Disconnected Connected Connected E Disconnected Disconnected Connected Disconnected Disconnected C Disconnected C Disconnected C Disconnected Disconnected Disconnected Disconnected E Disconnected EZ aa IP Domain Name 192 168 10 89 192 168 10 77 192 168 10 100 192 168 10 98 192 168 10 96 192 168 10 101 192 168 10 130 192 168 10 131 192 168 10 133 192 168 10 134 192 168 10 135 192 158 10 136 192 168 10 137 192 168 10 138 192 168 10 139 192 168 10 211 192 168 10 221 192 168 10 231 192 168 10 232 192 168 10 233 192 168 10 234 192 168 10 235 192 168 10 236 192 168 10 237 MAC Address D0 1C 6
9. VS 540 HDSDI 2 0 Megapixel IP Camera with HDSDI output User Manual ver 1 0 VlwO 10062010540 VS 540 HDSDI User Manual Safety Precaution We appreciate your purchasing VS 540 HDSDI Before installing the product please read the following with care Make sure to turn off the power before installing VS 540 HDSDI Do not install under the direct sunlight or in dusty areas Make sure to use the product within the temperature and humidity specified in the specification Do not operate the product in presence of vibrations or strong magnetic fields Do not put electrically conducting materials in the ventilation hole Do not open the top cover of the product It may cause a failure or electric shock on the components To prevent from overheating make sure to keep the distance at least 10cm from the ventilation hole Make sure proper voltage 220V 100V before connecting the power 2 0 Megapixel IP Camera Manual 2 51 VS 540 HDSDI User Manual Table of Content Ur deele de anana aa aa aa taa na 4 PROOUN UNIS TYAN estes oct cea pee KENE a aa a be 4 SE 4 Product and Accessories Part Names and Functions VV 6 Pan Names AREA OS anniari n nana E EErEE AUER NENEN K EEEN a EEEN EENET NNR ENEA NENNE 7 SEENEN 8 VAM ET DT ne 11 ROTI CUI OIA RENTE TT m a aa A a aaa Ka gang ga gana paia 11 EE ORE OT mm 12 Oe OO DCT
10. bit PTZ PTZ Type Select the type of PTZ camera or receiver e PTZ ID Since it is possible to control multiple PTZ cameras or receivers over a single control line each camera or receiver must be assigned a unique ID Enter the PTZ ID of a camera or receiver for control The ID value range can be between 0 and 255 PTZ Port Select the serial port used for PTZ camera control Sensor Type The sensor port can be configured to the following rege See NO Normally Open The port is normally open and activated when closed NC Normally Closed The port is normally closed and activated when opened The function of the sensor port is set based on the type of the sensor connected Sensor Schedule f you select sensor ON Each sensor port can be enabled or disabled by day of the week and hour units Sensor is disabled during the grey colored duration 2 0 Megapixel IP Camera Manual 34 51 VS 540 HDSDI User Manual Event Configuration Setup Live View Change User System Video Audio Network Serial Event Preset Record User Camera Event Local sensor Alarm E mail Clm No Preset On Video Loss Alarm CJE mail LIFTP No Preset w On Motion Alarm E mail L FTP No Preset v Remote sensor Alarm E mail FTP No Preset sensor Alarm D E mail FTP No Preset sensors Alarm E mail J FTP No Preset sensord Alarm E mail FTP No Preset On Disconnect On Disconnect Alarm
11. bout 10 minutes from the start of the recording The actual time depends on the Max file size which will determine the length of each segment Press the Search Page button on the Record setup page Dates with recording data will be shown as follows Search Page 2008 03 03 I H 1 HI First choose the date for your search and a list of AVI files will be shown The file name shows the date and time Date Begin Time End Time avi Root gt gt 2008 03 03 C File Name Size O 080303 155722 155731 avi 1 30 M D 080303 165355 165608 avi 22 51 M CI 080303 155143 165213 avi 4 48 M Iis LI Press Root to move back to the page with date list e Playback Selecting an AVI file will show a dialog for opening or saving the file File Download En Do you want to open or save this file Name 080303 165143 165213 avi AVI Type Video Clip 3 27MB c Geel While files from the Intemet can be useful some files can potentially e harm your computer If you do not trust the source do not open or save this file What s the risk Press the Save button to store the file on the PC The AVI file can be played with Windows Media Player 2 0 Megapixel IP Camera Manual 44 51 VS 540 HDSDI User Manual f you press the Open button in the dialog box the file will be downloaded and played automatically with Media Player While downloading a file all other web connections are disabled
12. ct Preset Ki Sensor Input Alarm output Qi Snapshot Talk fe og Con File Record Start J 2 0 Megapixel IP Camera Manual 13 51 VS 540 HDSDI User Manual e Video Selection Select the Video stream to be viewed Primary or Secondary VS 540 HDSDI is capable of dual streaming primary streaming and secondary streaming Video will be displayed according to the resolution set in video configuration If dual streaming Use Dual Encode Menu in Video page is not activated secondary video is not available Screen Size Adjust the Screen size Screen size is initially adjusted according to the compression resolution If you click x1 2 icon the whole screen size will be reduced by half Digital Zoom r H Control the Digital zoom on the screen The more the camera zooms in the smaller the square of the control panel is lt gt The Position of the image can be changed by moving position of the square Max x5 Digital Zoom is available If you press x1 the screen will return to 4 v the normal size foomin Zoom Out e PTZ Control Panel Optical Zoom Control PTZ and PTZ Control Panel is used for controlling external PTZ devices when the external PTZ devices are connected through serial port Since x10 optical zoom lens is built in VS 540 HDSDI it is possible to control zooming by using the Zoom in out buttons of the PTZ control Panel Zoomin Zoom Dut rome Focus Near Focus Far Auto Focus Foc
13. ddress hh mm ss will be generated in the specified folder Video Monitoring with Decoder System Once VS 540 HDSDI s IP address is set in the remote IP address section of the decoder the decoder system will connect to VS 540 HDSDI and start receiving the video images Normally a monitor connected to the decoder will display video images 2 0 Megapixel IP Camera Manual 15 51 VS 540 HDSDI User Manual Initialization of IP address If a system IP address is lost the system can be reset to the system default IP address using the Reset button on the back side of the system 1 While the system is in operation press the Reset button for more than 5 seconds 2 The system will reboot automatically 3 Once the system reboots IP address will be set to the system default as below 2 0 Megapixel IP Camera Manual 16 51 VS 540 HDSDI User Manual 4 Remote Configuration Using Web Brower Remote Setup is available by using the web browser Enter the IP address of VS 540 HDSDI and the live view screen appears as below Press the Setup button located in the upper right area of the monitoring screen to go to the server setup For Remote Setup the user must be authorized at higher than manager level Enter IP Address P X r E Y 7 2 UL UU Video Surveillance Wind ys Internet Explore C Te http 192 168 10 135 FS 6 eege RE 2 Press Setup button H Ze T e w dr video Surveillance if
14. e level of Admin user Modify Privilege Level ID user Priviege Level User v Modify f Cancel Login Policy Authentication Type For user login the following access algorithms can be selected Basic or Digest HTTP authentication based on RFC 2617 HTTP Authentication Basic and Digest Access Authentication is supported e Skip Login Skip Login provides for convenient access to the server when authentication is not required When Skip Login is set to Enable the login step is skipped The privilege level after login skip is determined by the setting of Privilege Level After Login Skipped 2 0 Megapixel IP Camera Manual 49 51 TCAM 540 X10S User Manual Camera Configuration Setup Live View Change User System Video Audio Network Serial Event Preset Record User Camera Camera Daye Night White Balance WB Mode Auto Exposure AE Made Full Auto bul OSS Mode off Auto OSs Limit 1 15 v Back Light Compensation of on ele Digital Zoom off on Aperture Level Day amp Night The camera delivers color images during the day As light diminishes below a certain level the camera can automatically switch to night mode Black amp White mode to maintain good image quality e Day amp Night function can be selectable according to environment Auto Automatically switches to Day Color or Night B amp W according to light using ICR Infrared Cut filter Removable
15. em 2 0 Megapixel IP Camera Manual 471 51 VS 540 HDSDI User Manual User Configuration Setup Live View System Video Audio Network Serial Event Preset Record User Camera User User List ID Privilege Level admin Admin Gi user Manager Q Modify Password Modify Privilege Login Policy Authentication Type 9 Basic Digest Skip Login 9 Disable Enable Privilege Level After Login Skipped Admir User List Users can be registered and the privilege level of a user can be specified User configuration is allowed only by the Admin user A Max of 16 users can be registered and each user can have one of four privileges All operations User ID admin Live viewing and PTZ control All operations except for user Manager configuration Add User Press the Add button The following window will appear Add User ID Password Privilege Level Manager Y Enter the User ID and password up to 15 characters and select Privilege Level 2 0 Megapixel IP Camera Manual 48 51 VS 540 HDSDI User Manual Delete User Select the User to be deleted and press the Delete button Change Password Press Modify password button The following window will appear Modify Password admin oro Modity Cancel Enter the current password and then set a new password Modify Privilege Level Press the Modify Privilege button to change the User level It is not allowed to change the privileg
16. erval Max 3600 sec Recording duration is not included inthe transmission interval For example if the Upload interval is 60 seconds and the Upload duration is 20 seconds a Video clip of 20 seconds is transmitted every 80 seconds Event Record e Specify duration of recorded video generated by events to send through E mail or upload through FTP Pre event Time Specify the duration of the recording before an event happens Post event Time Specify the the duration after the event is cleared Max duration is 30 seconds 2 0 Megapixel IP Camera Manual ool VS 540 HDSDI User Manual Preset Configuration Setup Live View Change User System Video Audio Network Serial Event Preset User Preset Preset1 2 Preset 3 Preset3 Move PTZ Camera to normal view ITI 2 E Q E D OO000o0O0O0O00000o00Q D s ef Press Set Button Save This function is only available when a PTZ receiver is used with the camera Configure up to 15 preset positions Preset function is not available on some PTZ receivers Make sure to check if a PTZ receiver supports presets Preset Configuration e Setthe PTZ Presets by following the next steps Move the camera to a desired view using the PTZ control buttons Enter Preset name Press Set button Once all the presets are set press Save List button e Move to Preset Position Select a preset from the Preset and press Go To button the came
17. es compute their local time as an offset from UTC Coordinated Universal Time In casual use GMT Greenwich Mean Time can be considered equivalent to UTC Local time is UTC plus the current time zone offset for the considered location Automatically synchronize with NTP server Checking this box will Synchronize the camera time with an NTP server using NTP network time protocol Enter the NTP server name of the NTP server to be used The Network Time Protocol NTP is a protocol for synchronizing the clocks of computer systems over packet switched variable latency data networks It is designed particularly to resist the effects of variable latency by using a jitter buffer Reboot Pressing this button will Reboot the camera Do not press the Reboot button unless required 2 0 Megapixel IP Camera Manual 20 51 VS 540 HDSDI User Manual Factory Reset This changes the Current IP Address of VS 570 HDSDI to default IP Address 192 168 10 100 The System log and user registrations are also cleared All other setting values will remain Note that the Password will not be changed by the Factory Reset for the security purpose Please contactMarshall Electronics Technical Support if you forget your password 2 0 Megapixel IP Camera Manual 21 51 VS 540 HDSDI User Manual Video Configuration System Video Audio Video Encode Setup Live View Network Serial Event Preset Record User Camera Enable Pre
18. et O2 oo e an Saat a3 e Recording status can be also shown in True Manager When data is being recorded Record column displays ON sign 3 True Manager Group Server Tools View Help Groups eri Gg vers 3 Server Name Ch Conns io record W E kbps V fps V D kbps V D fps A E kbps A D K 7 Es ON 3828 30 D n Disconnected Disconnected Disconnected Disconnected Disconnected Disconnected C Disconnected Disconnected Disconnected Connected Connected Disconnected Disconnected Connected C Disconnected Disconnected C Disconnected Disconnected C Disconnected Disconnected Disconnected Disconnected Search and Playback Recorded File Recorded video and audio data can be saved as AVI format in the disk In general one AVI file is created for each event in case of Event Based Recording However it is possible that data recorded by a series of events happening continuously can be merged to a single AVI file depending on pre post event time setting The file size is limited to 10 200MB or 10 minutes n case of Continuous Recording AVI files are created in series and the size of each is limited to 10 200MB or 10 minutes 2 0 Megapixel IP Camera Manual 43 51 VS 540 HDSDI User Manual e Search A file currently being recorded will not appear until after it is completed For Continuous recording a file will appear after a
19. format is recommanded USB or SD Disk available Available to be used for recording Disk formatting Start Disk is being formatted System should not be turned off during formatting Disk formatting Progressing Disk formatting Writing inode tables 63 619 Disk formatting Creating journal Disk formatting Writing Superblocks Disk format done Please wait for reboot Disk removed The Disk was detached during operation or there is damage to the file system If this happens while the disk is connected it is recommended to format the disk or in abnormal state 2 0 Megapixel IP Camera Manual 41 51 VS 540 HDSDI User Manual General Use record On Recording function will be used when On is selected Off Recording function will not be used when Off is selected Select Video Select video streaming between primary video and secondary video Overwrite Configure the overwrite option when the disk is full If Overwrite is set Off recording will stop automatically when there is less than 100MB of free space remaining on the disk If Overwrite is set to On recording will continue by deleting the oldest data on the disk first maintaining free space of 300MB for normal operation e Max File Size The Max File Size option sets the size of AVI files If a small file size is set files of smaller size will be generated but the numbers of files will be increased If recording time is more t
20. han 10 minutes a new file will be created even though the file size is set to be smaller than set max file size Event Type Three recording modes are supported in VS 540 HDSDI Full time Event and Disconnect Event recording allows event types to be selected from mong several events Event types are sed for configuring the schedule table Up to 4 event types can be configured and each event type can be a combination of sensor video loss and motion event Pre event Time Specify the duration of the recording before an event happens Post event Time Specify the the duration after the event is cleared Schedule Table The recording mode is determined by selecting Off Continuous or Disconnect When to Record is configured by the checking boxes in Schedule Table for the appropriate day of th e week and time of day Each recording mode configures the recording operation as follows Record off No recording Continuous Records continuously Disconnect Data is recorded when the system loses the connection to its client Decoder CMS NVR etc NOTE If one of multiple client systems is disconnected this will not trigger record Event Type Records when an event configured in Event Type setting occurs 2 0 Megapixel IP Camera Manual 42 51 VS 540 HDSDI User Manual Checking status of recording Recording status can be shown on the main view page Live View Setup nge User Video Server Q view Size 7 ne Zs Qx12 G
21. he ON to enable to use Dual Encoding The secondary video can be viewed in the Live View window by selecting Secondary on Video selection e Dual Compression Algorithm Select H 264 or MJPEG for the secondary streaming Maximum resolution is1280 x 720 and 9 steps of resolution are available If MJPEG is selected only Quality mode is supported Motion Detection Use Motion Detection Select ON to use the Motion Detection function e Motion Detection Area Editing Configure regions for motion detection Regions of arbitrary shapes can be configured using the following steps Select the Enable button ajacent to the Edit heading Select editing Mode Set is for including cells to motion detection region and Erase is for excluding Select cells using the right mouse button Multiple cells can be selected conveniently by pressing and dragging Press Apply Edited Area to save the editing Motion Detection Use Motion Detection Off On p 1 d ix IBS IRER a LEOFA LAJIZ E JEBBNELzzz ABEERRE KI LL hee TERE et HEHNBENBNBUC i it Enabl Disabl SRE nable Disable Apply Edited Area Mode Set 9 Erase Sr ea Sensitivity D for most sensitive Se 5 2 0 Megapixel IP Camera Manual 25 01 VS 540 HDSDI User Manual Sensitivity Sensitivity selects the amount of movement required to trigger detect a motion event The value determines the sensitivit
22. his mode Refer www dyndns org for details ID Password and Domain name are needed when DynDNS is set Dynamic DNS is a method protocol or network service that provides the capability for a networked device such as a router or computer system using the Internet Protocol Suite to notify a domain name server to change in real time ad hoc the active DNS configuration of its configured hostnames addresses or other information stored in DNS Check IP Disable If Check IP Disable is selected IP Server will skip to check its own IP In Fixed IP mode the set IP will be registered on DDNS server In DHCP mode the allotted IP will be registered on DDNS server Normally Check IP Disable can be unchecked Bitrate control When there is more than one client connected to theVS 570 HDSI due to bandwidth difference among the clients some of them may not have enough bandwidth to receive the encoded stream completely In this case itis possible to select the way to stream video to clients as follows Frame Drop Mode Encoding will be adjusted to the client with the highest bandwidth Clients with limited bandwidth may not receive all the frames Suppression Mode Bit rate and frame rate are adjusted most efficiently for all clients In this case all clients can be affected by the averaged bit rate and frame rate Address Info e The following network information is displayed as Read only IP Address The Camera s own IP addre
23. ht As both Gain and lris are fixed this mode is used when exposing at a fixed camera sensitivity Spot Light Avoids a situation where the face of the subject is over illuminated and becomes whitish In Spot AE a particular section of the subject can be designated and then that portion of the image can be weighted and a value computed so that Iris and Gain can be optimized to obtain an image Digital Zoom Determine the Digital zoom 12x supported by the camera zoom lens x10 Optical zoom and x12 Digital zoom lens f 5 1 5 1mm is built in VS 540 HDSDI Aperture Level oet Aperture Level from 0 to 15 Aperture control is a function which adjusts the enhancement of the edges of objects in the picture There are 16 levels of adjustment starting from no enhancement When shooting text this control may help by making the text sharper 2 0 Megapixel IP Camera Manual 51 51 v1 0 10062010540
24. ing the system is ready The software provided in the CD called True Manager allows you to check the IP address and other network details of the camera Please refer to the True Manager manual for instructions on how to find the IP address of the camera and change it if required 2 0 Megapixel IP Camera Manual 12 51 VS 540 HDSDI User Manual 3 System Operation Remote Video Monitoring There are two ways to monitor video when the center system and VS 540 HDSDI are connected In order for a proper operation an IP address must be set accordingly Please refer to True Manager in Chapter 3 or Remote Setting in Chapter 4 for further details Default ID admin Default Password 1234 Video Monitoring using Internet Explorer Live View Setin Change lleer Open Internet Explorer and enter VS 540 HDSDI s IP address The system will ask for confirmation to install Active X control Once authorized the Internet Explorer will start to display video images from VS 540 HDSDI as shown below Default IP Address http 192 168 10 100 Live View am Video Select Primary Secondary View Size x0 5 Ox1 we IC y A W Pp z x S 1 dr f AHH ZA j Ze Le MNT Y on lt gt TEE CSN AM E es SAL E I VV in ene ME TAMEL TU nl af KA is PAYA CN KNE Sa SE eg y I d f SEN H iT f 4 h fe wa 4 VI JAH T b j A a N gt ee A yu f A bow d i A Sele
25. nder Address Enter an account registered in the SMTP server ID amp password When the server requires authentication ID and Password of an E mail account need to be entered Destination address Enter the Destination address More than one address can be entered by delimiting comma or semi colon The Destination address can be up to 63 characters long Video Clip Attaching A Video clip stored at the moment of an event can be attached as an AVI or JPEG file format If using dual Encoding Primary video or Secondary video H 264 only can be selected FTP Upload e Specify the FTP configuration to upload event information when FTP is selected as an event action Server Address Enter the address of an FTP server to receive video files Port Specify a port for FTP operation Port 21 is the default port in FTP operation If a different port is configured in the FTP server this port needs to be changed accordingly ID amp password Enter ID and Password for accessing the FTP server Upload video Primary video and Secondary video H 264 only JPEG can be selected as an upload method Number of Frame Enter a frame number of JPEG Capture from 1 to 10 Continuous upload Continuous upload on allows the video image to be transmitted regularly regardless of the occurrence of events Upload duration Specify recording duration of a video clip to be transmitted Max 300 sec Upload interval Specify transmission int
26. plays the current firmware version Board ID Displays the Network board ID of VS 540 HDSDI recognized by system Upgrade Upgrade firmware 1 2 3 4 Press the Browse button to select a firmware file from PC Press the Firmware Upgrade button to start to upgrade Messages showing the status of downloading upgrading will be displayed The camera will reboot automatically after completing the upgrade Do not turn the camera off during the Upgrade process Firmware Version Enc V1 102D 001 Board ID 47 Now Downloading Please wait Upgrade D Xcckskim update fwihvsSys102C Browse Naw Llporading Please wait a minute 2 0 Megapixel IP Camera Manual 19 51 VS 540 HDSDI User Manual Time e Start Time This is the date and time when the camera was booted Current Time Current date amp time Enter a new date and time and press Set Current Time button to update Time Format This allows you to change the time format Selectable time formats are as follows YYYY MM DD hh mm ss Ex 2010 4 11 18 18 42 DD MM YYYY hh mm ss Ex 11 4 2010 18 18 42 MM DD YYYY hh mm ss Ex 4 11 2010 18 18 42 Time Zone This allows you to select time zone where the camera is installed Depending on the time zone Daylight Saving Time will work automatically A time zone is a region of the earth that has uniform standard time usually referred to as the local time By convention time zon
27. ra will move to the selected preset position 2 0 Megapixel IP Camera Manual 38 51 VS 540 HDSDI User Manual Record Configuration Setup Live View Change User System Video Audio Network Serial Event Preset Record User Camera Record Disk Information USB Disk available Disk size 7 40 G Free Space 5 88 G General Use Record Off On Select Video Primary video Secondary Video Overwrite Off On Max File Size 100M bytes ze Event Type Event Type 1 OI Sensori D Sensor D Motion D video Loss Event Type 2 C Sensor D Sensor D Motion D video Loss Event Type 3 C Sensori D Sensor D Motion D video Loss Event Type 4 C Sensori LJ Sensor D Motion D video Loss Post event Time Schedule Table Record Of Continuous Disconnect Select Event Type 1 Event Type 2 Event Type 3 Event Type 4 0 1 2 3 4 5 B 7 8 9 D 11 1213 14 15 16 17 18192021 2223 2 0 Megapixel IP Camera Manual 39 51 VS 540 HDSDI User Manual Recording to SD Card A V data can be recorded to an internalSD card An SD card with at least 1GB of storage space isrecommended Either EXT3 or FAT32 file system can be used A Linux PC can read any of these file systems On the other hand a Windows PC can only read a FAT32 File A video bit rate of 4Mbps or less is recommended when you record and monitor video at the same time as higher bit rates may cause frame loss Disk information and recording setup 6
28. rresponding IP address 207 171 166 48 Each organization that maintains a computer network will have at least one server handling DNS queries That server called a name server will hold a list of all the IP addresses within its network plus a cache of IP addresses for recently accessed computers outside the network Port e Base Port Enter the Base Port number The Network base port is used for communication between systems In order for VS 540 HDSDI and remote systems decoder or CMS NVR software to be connected the port numbers must be identically set HTTP Port Enter the HTTP port used for web based connections RTSP Port Enter the RTSP port used for RTSP based connection The default RTSP port is 554 RTSP Real Time Streaming Protocol is a standard for connected client s to control streaming data over the World Wide Web Authentication e RTSP Authentication If the RTSP Authentication set to ON the user must enter correct User ID and Password when any RTSP client is connected e HTTP API Authentication When HTTP API authentication set to ON HTTP Authentication is asked for all clients which use HTTP API RTP Session RTP Real Time Transport Protocol is an Internet protocol used for transmitting single real time multimedia data such as audio and video to a select group of connected clients Normally RTSP uses RTP to format packets of multimedia content RTP Session menu is used when the RTP only
29. s can be connected in either 1 to 1 connection where one VS 540 HDSDI is connected to one PC client or a decoder system or 1 to many connections where one VS 540 HDSDI can be connected to several PCs and decoder systems The VS 101 video server can work as a video decoder which takes the data from a video server or IP camera decodes and outputs analog or digital video Topology Generally VS 540 HDSDI and PC or a decoder is connected in 1 to 1 mode or 1 to many configuration e 1 1 Connection one Remote Center Decoder Remote Center Uu J S Site Remote Center PC SW us One VS 540 HDSDI is installed at a site where video images are transmitted A PC or a decoder is installed at a central location to receive and view the video images on an analog monitor Audio and serial data are transferred in either direction 2 0 Megapixel IP Camera Manual 8 51 VS 540 HDSDI User Manual 1 N Connection Site Remote Center In this configuration a site can be monitored from many remote central locations Although up to 64 PCs or decoders can be connected to one VS 540 HDSDI in the real network environment network bandwidth can limit the maximum connections Functionally the central monitoring system CMS software provided can replace the decoder Multicast Mode If the network supports multicasting a large number of decoders can be used to receive video effectively from a VS 540 HDSDI using a
30. s used when the encoding resolution is different from the input compression Without the Scaling option input video will be croped according to the encoding resolution On the other hand if Scaling is selected the input video will be adjusted according to the encoding resolution Frame rate Select the maximum number of frames per second for the video stream A frame rate of 1 2 3 4 5 6 8 10 15 20 25 and 30 can be selected The actual frame rate of video can be less than the maximum frame rate set due to any network bandwidth limitation Preference select encoding mode to control video quality Quality or Bit rate If Bit rate is selected the video encoding will be affected by the Bit rate value entered Therefore Bit rate mode is CBR Constant Bit rate encoding If Quality is selected the video encoding will be affected by the quality of image selected Therefore Quality mode is VBR Variable Bit Rate encoding e Quality Select the required Video quality Eight levels of quality are available Quality mode VBR encoding adjusts the bit rate according to the image complexity using higher bandwidth for increased activity in the video and lower bandwidth for decreased activity For active video content such as sports or when network bandwidth is limited It is reccomended that CBR or Bit Rate encoding be used 2 0 Megapixel IP Camera Manual 23 01 VS 540 HDSDI User Manual e Bitrate Set the bit rate
31. single streaming of video and audio However multicast mode is possible only when the network environment supports multicast Relay Site Center 1 Decoder Center 2 Decoder Video and audio data can be retransmitted from one center to another center This arrangement is useful when the network bandwidth to the site is limited and there are more than one center wanting to monitor the site 2 0 Megapixel IP Camera Manual 9 51 VS 540 HDSDI User Manual CMS Central Monitoring System Site Remote Center CMS Central Monitoring System is a Window based remote monitoring program used to monitor or control video audio and events in real time from several IP cameras or video servers Please refer to the CMS User Manual for more in detail 2 0 Megapixel IP Camera Manual 10 51 VS 540 HDSDI User Manual 2 Installation Connection Connecting Power 1 Carefully check the voltage and current capacity of the rated power The rated power is indicated on the back of the main unit 2 After confirming the power source connect the power adaptor and connect the 12V DC connector to the system Connecting Network 1 Plug the network cable to the Ethernet port RJ 45 network port Connecting Video 1 To display video through the HD SDI port connect to a monitor using a BNC coaxial cable 2 Set Enable Preview option ON on the Video tab of the web page Please refer to the Video Configuration part When using H
32. sion modes CBR VBR Motion detection Composite or HD SDI or HDMI video output Depending on Models Multi transmission mode Simplex VS 540 HDSDI gt Client PC or Decoder Client PC or Decoder VS 540 HDSDI Full Duplex Fixed IP amp Dynamic IP DHCP support 1 1 1 N support Multicasting Various types of Protocol support TCP IP UDP Multicast DHCP SMTP HTTP SNMP RTP RTSP 2 0 Megapixel IP Camera Manual 4 51 VS 540 HDSDI User Manual Serial Data e RS 485 support e Data pass through mode Serial data communication between VS 540 HDSDI and Decoder Sensor and Alarm e Event Alarm notification e alarm sensor Inputs and 1 alarm Output relays are available User Interface e Diagnose and upgrade through dedicated program called True Manager e System configuration using Internet Explorer High Reliability e Reliable embedded system 2 0 Megapixel IP Camera Manual 5 51 VS 540 HDSDI User Manual Product and Accessories SW and User Manual CD VS 540 HDSDI Quick Guide 2 0 Megapixel IP Camera Manual 6 51 VS 540 HDSDI User Manual Part Names and Functions Rear Connector Function 1 Ethernet 802 3af Ethernet port 802 3af LED OT kee 6 SENSOR ALARM Sensor input Alarm output 7 RS 485 RS 485 port 8 VIDEO OUT HD SDI 9 SD CARD SD memory card slot 2 0 Megapixel IP Camera Manual 7 51 VS 540 HDSDI User Manual System Connections VS 540 HDSDI IP Camera
33. ss This information is useful when the camera s IP mode is set to DHCP Domain Name If the camera is registered at a DDNS server the registered domain name is displayed MAC Address Displays the MAC address of the camera If the camera is registered at a DDNS server the MAC address is used in DDNS registration Connecting Client IP Addresses that are currently connected to the system are listed 1 Indicates Primary Streaming and 0 Indicates Secondary streaming 2 0 Megapixel IP Camera Manual 32 51 VS 540 HDSDI User Manual Serial Configuration Setup Live View Change User System Video Audio Network Serial Event Preset Record User Camera Serial COM2 RS 465 Port Protocal Bitrate 2400 bps Data Bit BBits Parity None stop Bit 1Bits PTZ PTZ Type Pelco D PT ID 1 PTZ Port Sensor ype Sensor Q Of NO ON C Sensor Schedule Select Gei Sensor On sensor 1 OT 2 5 45 6 2 8 9 Un 1121314555 218419 20215 22 73 SUN BERR RRR MON RRR RR TUE BERR REE WED BERR cr BERR 2 0 Megapixel IP Camera Manual 33 51 VS 540 HDSDI User Manual Serial Port Configuration e Serial Port Information The RS 485 in the VS 540 HDSDI support one RS 485 serial port The serial ports can be configured as follows Each of the serial ports configurations must be same as the connecting device 2400 4800 9600 19200 38400 57600 Bitrate 115200 bps Data Bits 5 6 7 8 bits Stop Bit 1 2
34. streaming without RTSP connection RTP stream will be transmitted to the destination set The SDP Session Description Protocol file can be found in the server and a client can retrieve it using http connection 2 0 Megapixel IP Camera Manual 30 51 VS 540 HDSDI User Manual Related settings are as following Destination IP Set the IP Address for your destination system which will receive RTP stream Destination Port Set the Port for your destination system which will receive RTP stream User Name Enter the User name that will be used as session name in the SDP file File Name Enter the file name that will be used as the name of the SDP file It can then be accessed through http ServerAddress filename RTP Session Use RTP Session Off On Destination IP 192 168 10 151 Destination Port 34567 User Name username File Name filename SNMP e The VS 540 HDSDI can be used as an SNMP agent It is compatible to both SNMPv1 and SNMPvec Settings for using SNMP Simple Network Management Protocol are as follow SNMP Listen Port This port is used for connecting external devices when the system operates as an SNMP client SNMP is not used when setting a O value SNMP Trap Destination IP Set the SNMP Trap Destination IP SNMP Trap Destination Port Set the SNMP Trap Destination Port SNMP is not used by setting O value SNMP SNMP Listen part 151 SNMP Trap Destination IP 192 158 10 100 SNMP Trap Destina
35. tem The following table lists the possible actions for events NEN WEM MEE Triggers alarm relay port E mail Sends E mail to the specified address an AVI file can be attached FTP Upload AVI file to a specified FTP server Preset Move to the Preset position Local amp Remote Event Configuration e Sensor1 Sensor2 Sensor3 Sensor4 Configures the actions when the sensor is activated Multiple actions can be set for a single event e On Video Loss Configures the actions when video input signal is lost Multiple actions can be set for a single event e On Motion Configures the actions when motion is detected Multiple actions can be set for a single event e On Disconnect Configures the actions when the link connection with peer system is disconnected Multiple actions can be set for a single event Alarm and Beep activation duration 6 Set the duration of alarm or beep activation in case of an event If it is set to continuous it will be in an active state until an operator resets it manually 2 0 Megapixel IP Camera Manual 36 51 VS 540 HDSDI User Manual E mail Notification Specifies the E mail configuration when E mail is selected as an event action Server Address Enter an address of mail SMTP server Port Specify a port for SMTP operation Port 25 is the default port in SMTP operation If a different port is configured in the SMTP server this port needs to be changed accordingly Se
36. tion Port 162 Simple Network Management Protocol SNMP is used by network management systems to communicate with network elements SNMP lets TCP IP based network management clients use a TCP IP based internetwork to exchange information about the configuration and status of nodes SNMP can also generate trap messages used to report significant TCP IP events asynchronously to interested clients For example a router could send a message if one of its redundant power supplies fails or a printer could send an SNMP trap when it is out of paper Multicast e Multicast IP The multicast IP address selection range is between 224 0 1 0 and 238 255 255 255 The selection can be used only when media protocol is set to Multicast The Multicast menu is used for the Multicast connection request from a decoder or CMS NVR software to transmit Multicast stream to the decoder or CMS NVR software The multicast address must be the same for the system to be connected using multicast protocol 2 0 Megapixel IP Camera Manual 31 51 VS 540 HDSDI User Manual DDNS select the DDNS Dynamic DNS server to use One of the two servers can be selected True DNS TrueDNS service is used in this mode Systems can be registered on the website for TrueDNS service http ns1 truecam net The System will get a domain name of xxx truecam net style Please refer to the user guide document for True DNS service DynDNS DynDNS service is used in t
37. tion Port Multicast Multicast IP 224 10 0 0 2 0 Megapixel IP Camera Manual 28 51 VS 540 HDSDI User Manual DDNS DONS Sever None TrueDNS DynDNS CT Check IP Disable Password Domain Name Do OS Flow Control Mode Frame Drop Mode Suppression Made Address Information Bitrate Control Current IP 192 168 10 105 Current Domain demo3 truecam net MAC Address 00 10 63 A4A 01 55 Connecting Local e IP mode Select the IP mode Fixed IP or DHCP Dynamic Host Configuration Protocol Depending on the mode selected configuration items will appear as follows Local IP Fixed IP address Local Gateway IP address Gateway Local Subnet Subnet mask 5 Please request IP address information from your ISP provider or network manager DNS Obtain DNS server address automatically The DNS server address automatically aquired when IP mode is DHCP Use the following DNS server addresses Manually enter the DNS server IP address Primary DNS server Secondary DNS server 2 0 Megapixel IP Camera Manual 29 51 VS 540 HDSDI User Manual Domain Name System DNS is a database system that translates a computer s fully qualified domain name into an IP address Networked computers use IP addresses to locate and connect to each other but IP addresses can be difficult for people to remember For example on the web it s much easier to remember the domain name www amazon com than it is to remember its co
38. twork Serial Event Preset Record User Camera Audio Algorithm Algarithm CG 711 AAC Bitrate GO B4kbps 128kbps Mace Mode O Off OTx only ORx only Tx amp Rx Input Gain Input Gain e cp AN Algorithm e Algorithm select the audio algorithm G 711 or AAC e Bitrate Select the Bitrate to be 64kbps or 128kbps when AAC is selected The sampling rate is fixed to 32KHz when G 711 is selected Note that when VS 540 HDSDI is connected to a decoder the decoder s audio algorithm MUST be set identically to transmit audio and video properly Mode e Select the audio Transmit Receive mode Me Aan o Tx Only Transmit only Transmit and Receive Input Gain e Set the audio input gain from O to 31 2 0 Megapixel IP Camera Manual 2101 VS 540 HDSDI User Manual Network Configuration Setup Live View System Video Audio Network Senal Event Preset Record User Camera Network Apply Local IP Mode Local IP Local Gateway Local Subnet 255 265 256 0 DNS Obtain DNS server address automatically Use the following DNS server addresses Primary DNS Server 168 126 63 1 Secondary DNS Server 168 126 63 2 Port Base Port 2223 HTTP Port 80 RTSP Port 554 Authentication RTSP Authentication Off On HTTPAPI Authentication Off On RIP Session Use RTP Session of On Destination IP 0 0 0 0 Destination Port 0000 SNMP SNMP Listen port SNMP Trap Destination IP SNMP Trap Destina
39. us Near Focus Far Aulo Focus Menu On Enter ESC Adjusts the focus of the lens e Menu On Enter ESC Displays and control the OSD On Screen Display menu if OSD menu is supported NOTE VS 540 HDSDI does not support OSD menu 2 0 Megapixel IP Camera Manual 14 51 VS 540 HDSDI User Manual e Select Preset Set preset position and move to the specific preset position Go to Moves to the selected preset entry if the preset entry is set Set Sets the current position to the selected preset entry Clear Deletes the selected preset entry Sensor Input Displays the status of the sensor in real time When the sensor of the VS 540 HDSDI is working the sensor light turns red Alarm Output Operate the alarm device by pressing the number icon A number icon indicates the status of the alarm device e Screen Capture Captures video images and store them as BMP or JPEG files e Audio Transfer Transfers audio from a PC displaying the current video image to the VS 540 HDSDI File record Recording to an AVI file from the Live view page is possible AVI files are generated in the specified folder or file name on the PC where the web browser is running 1 Enter the drive and the folder name on the PC and enter the AVI File Record c storage test1 file name to be used 2 Press the Start button to begin recording Press the Stop button to end recording 4 The AVI file named File name IP a
40. value between 32 8000kbps Bit rate mode CBR encoding allows you to set a fixed bit rate that consumes a predictable amount of bandwidth If the network capacity is sufficient use of a fixed bit rate of 4096 kbps or higher will maintain a high quality picture regardless of content e Frame Interval Set the l frame Interval between 0 and 255 There will be no l frames if 0 is selected e H 264 Profile Select H 264 Profile High Profile or Baseline Profile The standard defines various sets of capabilities which are referred to as profiles targeting specific classes of applications High Profile HiP The primary profile for broadcast and disc storage applications particularly for high definition television applications for example this is the profile adopted by the Blu ray Disc storage format and the DVB HDTV broadcast service Baseline Profile BP Primarily for low cost applications that require additional data loss robustness this profile is used in some videoconferencing and mobile applications This profile includes all features that are supported in the Constrained Baseline Profile plus three additional features that can be used for loss robustness or for other purposes such as low delay multi point video stream compositing 2 0 Megapixel IP Camera Manual 24 51 VS 540 HDSDI User Manual Dual Encode Use Dual Encode 1 Select the Off button on the Enable Preview to enable to use Dual Encode 2 Select t
41. view Of On Resolution 1480x720 Ww Scaling Quality very fine Bitrate 2000 kbps 32 5000 Frame Interval ama 30 c H 264 Profile 9 High Profile Baseline Profile Dual Encode Use Dual Encode Off On Preference Quality Resolution CT Sealing Framerate 30 ei Quality Bitrate kbps 32 1024 Frame Interval mu X110 c H 264 Profile High Profile 9 Baseline Profile Motion Detection Use Motion Detection Of On Edit Enable Mode Disable Set Erase Apply Edited Area sensitivity 0 for most sensitive Information Display systemlD Time Position Burnin OSD stemm Time Position Font Size 2 0 Megapixel IP Camera Manual CO of O On of O On 9 Bottom Top Off O On Off 9 On Bottom Top Small 6x6 Middle 16x16 Large G2x32 22 51 VS 540 HDSDI User Manual Encode e Enable Preview 1 Select ON to display video on the monitor that is connected to the HD SDI video port 2 Select the appropriate Output format at the bottom of the Video page Note that when Enable Preview is ON dual streaming is not available When the video is transmitted directly to the monitor through the BNC cable the video signal bypasses the network and encoding e Resolution This allows you to Select the video encoding resolution Eighteen resolutions from 352 x 240 to 1920 x 1080 are available The Scaling option i
42. y of the motion detection within a block the lower the number the more sensitive to movement Select from 0 to 10 e Information Display System ID and or server time can be display over the video window in Internet Explorer Each item can be turned on or off separately and position also can be configured This information is displayed after the video is decompressed e Burn in OSD Insert system ID and date time in the compressed video System ID and time respectively can be turned on or off in the video the Position and Font size is selectable Note Since time information is inserted when the video is compressed the changing characters of the time display is detected as motion Therefore even though there is no motion an event will be triggered In order to prevent this exclude the area displaying time using Motion detection area editing Output Format The Output Format menu appears only when Enable Preview is on Output Format Output Format HOM amp HD SDI 20860 1200x720 Composite NTSC amp HOMI 4001 720x4850 Composite PAL amp HOMI 575i 20x576 HOM amp HD SDI 720p60 1250x720 HOM amp HD SDI 10860160 1920x1060 HOM amp HD SDI 720p50 260 201 HOM amp HD SDI 108050 1920x1060 Select the output format for the monitor preview according to the video output and monitor specification 2 0 Megapixel IP Camera Manual 26 51 VS 540 HDSDI User Manual Audio Configuration System Video Audio Ne
Download Pdf Manuals
Related Search