XT10 Horizontal axis
Contents
1. i 33 Maintenance WOrkS ii 33 Packing transport 35 Introduclion iii 35 Requirements on personnel carrying out the Work 35 Packing material ini das 35 Selection of packing material nenn 35 Procedure when packing nn nnnn nn 35 TAS O diciendo ddr 35 Data concerning goods to be transported nennen 35 Loading transferring the load unloading ooooccccnnnnccnnnnoccconnnccccannnrcccnnn 35 Fault clearance 37 Troubleshooting oriee isa elia alari iaia 37 Spare parts list 39 Ordering spare partS ii 39 XT10 Horizontal axis spare parts liSt i 40 DrVve unit e halo i ila sii incida 42 Running wheel bearing e 44 Guide wheel bearing nn 46 Electrical module s a reali 48 ni Gema General safety regulations This chapter sets out the fundamental safety regulations that must be followed by the user and third parties using the XT10 These safety regulations must be read and understood before the XT10 is put into operation Safety symbols pictograms The following warnings with their meanings can be found in the Gema operating instructions The general safety precautions must also be followed as well as the regulations in the operating instructions DANGER Danger due to electrically live or moving parts Possible consequences death or serious injury WARNING Im2. Information about the function mode of the individual system components booth gun control unit manual gun or powder injector should be referenced to their corresponding documents About this manual e 9 ni Gema Function description Field of application The XT10 Horizontal axis is used for the coating of parts with different widths By coating in this way the powder guns must be driven into each corresponding position for every given width The XT10 Horizontal axis can be used in connection with a ZA reciprocator XT10 Horizontal axis with ZA reciprocator XT10 Function description e 11 Gema Special characteristics V 02 13 The XT10 Horizontal axis is a feeding axis and has the following characteristics Same control as for the ZA reciprocator Freely adjustable speed setting on the axes control unit Built in leveling pads Minimum space requirement No additional space required for dismantling and service works Low overall height Manually movable when the control unit is switched off Intermediate and larger sizes available in steps of 50 mm For more information about the controlling of the axis see the axes control unit operating manual Reasonably foreseeable misuse 12 e Function description Operation in rooms with gases Horizontal axis is not anchored firmly to the floor The axis mounted on the horizontal axis is not fixed properly Incorrect programming of the end points and travel d
3. The XT10 horizontal axis was designed to operate with a minimum of maintenance The motor gear box is self lubricating and maintenance free Regular maintenance and inspection of the horizontal axis increases the working reliability and avoids damages repair downtimes etc Maintenance e 25 Gema V 02 13 Maintenance schedule Drive unit 26 e Maintenance Note The following maintenance schedule is based on operation of 8 hours per day Time interval Maintenance works weekly Blow off the outside of the horizontal axis with compressed air or clean it with a soft cloth at least once a week monthly Check the drive unit gearbox for oil loss Check the interior of the horizontal axis for deposits of powder dust and if present clean it every 6 months Check the drive belt for wear and tension Check the rollers on the carriage for free movement and wear Check the running surfaces for wear and deposits and if present clean them Note The parts which are to be replaced during maintenance work are available as spare parts Please refer to the spare parts list too Danger During assembly cleaning maintenance and commissioning when close to energized components an electrical shock can cause serious injury or death All work must be carried out only by technical personnel and when no power is applied The motor gear box is self lubricating and maintenance free Observe t
4. Order no 203 386 1 piece Clamp Y 18 15 mm When ordering cable or hose material the required length must also be given The spare part numbers of this bulk stock is always marked with an Wearing parts are always marked with a All dimensions of plastic hoses are specified with the external and internal diameter Example 8 6 mm 8 mm outside diameter 0 d 6 mm inside diameter i d WARNING Only original Gema spare parts should be used because the explosion protection will also be preserved that way The use of spare parts from other manufacturers will invalidate the Gema guarantee conditions XT10 Spare parts list e 39 Gema ee XT10 Horizontal axis spare parts list Attention When ordering toothed belts indicate the toothed belt length according to travel distance 855 mm AN By replacing the toothed belt screw in the grub screw so that the steel cables in the toothed belt are touched and the grounding is ensured 1 ZA carriage plate 387 355 2 Hexagon shakeproof screw M8x20 mm 244 422 3 Hexagon screw M6x10 mm 1001 081 4 Cover panel indicate the travel distance on request 5 Cover panel firm side 372 463 6 Hexagon screw M8x50 mm 213 993 7 Headless screw M8x60 mm 258 482 8 Clamping plate 372 420 9 Threaded bolt M10x140 mm 258 474 10 Hexagon nut M10 215 589 11 Clamp plate 345 067 12 Hexagon nut M12
5. 215 597 13 Threaded bolt M12x115 mm 372 676 14 Washer 13 24x2 5 mm 215 830 15 Washer M6 for countersunk head screw 258 431 16 Countersunk head screw M6x12 mm 214 680 17 _ Baseboard 372 404 18 _ Rubber buffer 35x40 mm M8 211 664 19 Buffer holder 389 285 20 Hexagon shakeproof screw M6x16 mm 244 503 22 Allen grub screw M6x10 mm 214 841 23 Drive belt 103 730 25 Running wheel bearing complete see corresponding spare parts list 28 XT10 drive unit complete see corresponding spare parts list 29 Guide wheel bearing complete see corresponding spare parts list XT10 Electrical module on ZA05 not shown see corresponding spare parts list Please indicate length Wearing part 40 e Spare parts list XT10 soli Gema XT10 Horizontal axis spare parts XT10 Horizontal axis spare parts list XT10 Spare parts list e 41 Gema ini Drive unit 4 Motor gearbox unit 0 18 kW complete pos 1 5 for XT Axes with serial numbers 18301 xxxx see Rating plate 1003 823 for XT Axes with serial numbers 18302 xxxx see Rating plate 1008 445 2 Torque support 6 mm 1003 819 3 Locknut M6 1003 822 4 Washer 6 4 16x1 6 mm 215 805 5 Cable bush ID 5 mm 1003 821 6 Motor cable L 2 5 m 387 169 8 Incremental pulse generator 268 925 10 Hexagon ribbed nut M12 1003 797 11 Hexagon shakeproof nut M6 244 430 12 Hexagon screw M10x20
6. O FS LS XT10 Horizontal axis running wheel bearing 44 e Spare parts list XT10 Rn Gema Running wheel bearing Running wheel bearing FS XT10 Spare parts list e 45 Gema ui Guide wheel bearing Guide wheel bearing complete LS 1003 803 Guide wheel bearing complete FS 1003 811 1 Guide wheel bearing support LS 1003 8044 1 Guide wheel bearing support FS 1003 8104 4 Guide profile 372 374 5 Guide wheel 73 mm 1003 805 6 Counter plate 372 382 7 Counter roller 390 658 8 Bearing bolt 1003 813 9 Deep groove ball bearing 10 35x11 mm 201 359 10 Deep groove ball bearing 15 52x15 mm 258 415 11 Snap ring l 35 216 135 12 Snap ring A 10 256 358 13 Snap ring A 25 237 094 14 Ribbed washer M8 242 870 15 Hexagon nut M6 205 095 16 Locknut M8 221 317 17 Countersunk screw K SI M8x70 mm 258 440 18 Hexagon screw M6x25 mm 213 845 19 Hexagon screw M8x10 mm 213 900 Wearing part o no LS FS XT10 Horizontal axis guide wheel bearing 46 Spare parts list XTIO Rn Gema Guide wheel bearing Guide wheel bearing LS XT10 Spare parts list e 47 Gema Electrical module V 02 13 Electrical module complete 1003 983 1 Position regulator CDB 1003 986 2 CAN bus cable 0 55 m 386 995 3 CAN bus cable 1 0 m 391 620 4 CAN T distribution box 265 772 5 Adhesive seal strip 9x2 mm 100 250 Please indicate l
7. motor drive unit The installation takes place exactly in the reverse order XT10 Maintenance e 27 Gema Drive belt A 28 e Maintenance V 02 13 Warning Injuries can arise if fingers hair or articles of clothing get caught between the drive belt and the drive wheel or toothed wheel All work must be carried out only by technical personnel The toothed drive belt should be checked regularly because it is exposed to large loads when in operation The drive belt should be checked for wear and tension every 6 months Powder deposits should be removed with a vacuum cleaner because this can influence the quiet running and shorten the service life of the drive belt Switch on the horizontal axis and check the drive belt for elongation or wear noisy running strong vibration of the belt when reversing the direction of travel Warning For safety reasons two people should always carry out the following maintenance work Tensioning the drive belt XT10 Horizontal axis Tensioning the drive belt Clamp the drive belt 23 with the clamp block 8 and tighten the screws 6 Tension the drive belt with the tensioning screw 11 so that the drive belt will deflect 2 3 cm Tighten the lock nut 10 XT10 var Gema Counter rollers If the X carriage starts to vibrate excessively during operation especially at the reversing points in most cases the cause lies in too much play in the carriage rollers or ev
8. En Operating instructions and spare parts list XT10 Horizontal axis Translation of the original operating instructions Gema Gema nt Documentation XT10 Horizontal axis Copyright 2004 Gema Switzerland GmbH All rights reserved This publication is protected by copyright Unauthorized copying is prohibited by law No part of this publication may be reproduced photocopied translated stored on a retrieval system or transmitted in any form or by any means for any purpose neither as a whole nor partially without the express written consent of Gema Switzerland GmbH OptiTronic OptiGun EasyTronic EasySelect EasyFlow and SuperCorona are registered trademarks of Gema Switzerland GmbH OptiMatic OptiMove OptiMaster OptiPlus MultiTronic and Gematic are trademarks of Gema Switzerland GmbH All other product names are trademarks or registered trademarks of their respective holders Reference is made in this manual to different trademarks or registered trademarks Such references do not mean that the manufacturers concerned approve of or are bound in any form by this manual We have endeavored to retain the preferred spelling of the trademarks and registered trademarks of the copyright holders To the best of our knowledge and belief the information contained in this publication was correct and valid on the date of publication Gema Switzerland GmbH makes no representations or warranties with respect to the content
9. e secured by the customer before start up and during operation by providing fencing see the local regulations 18 e Design and function XT10 i Gema Start up Assembly of the XT10 Horizontal axis The axis must be leveled in order to ensure a safe and perfect operation After positioning the XT10 Horizontal axis must be firmly fixed on the floor Connecting the XT10 Horizontal axis to the ZA reciprocator 1 The cables to be connected are lying loose on the carriage plate of the horizontal axis XT10 Horizontal axis with connection cable 2 Both cables must be inserted into the cable duct in the ZA reciprocator 1 3 Loosen the screws on the rear side of the ZA reciprocator and pull out the electrical modules XT10 Start up e 19 Gema ni XT Electrical modules in the ZA reciprocator 4 Break out the required opening in the feed through rubber and pull through the cables Cable feed through in the ZA reciprocator 5 Connectthe cable according to the enclosed wiring diagram 6 Push back the electrical modules and fasten them 20 e Start up XT10 lun Gema Preparation for start up Warning Before connecting or switching on the horizontal axis read N carefully these operating instructions Before the horizontal axis is put into operation the upper stroke limit must be set on the reciprocator control unit see the user manual of the axis control unit General information Warning B
10. efore start up works are done make certain that nobody can switch on the horizontal axis Switch off and lock the mains switch Before starting up the following checks should be done Check the gun holder and hose holder if they are firmly fitted Mount the gun holder in such a way that they do not hit the bottom of the booth slots on start up and cause damage Lay out the cables and hoses in such a way that even atthe highest stroke no strain can arise Make sure that no guns can collide with the work pieces Check the grounding of the guns and hose carriers Check if the upper and the lower reversing point of the Z carriage are set correctly The stroke length of the reciprocator must be in the range of the booth opening collision danger Make sure that the automatic guns cannot collide with the work pieces incorrectly adjusted stroke parameters on the reciprocator control unit Reference point At every start up after the mains have been interrupted the reference point of the reciprocator must be referred again see Reference point and mechanical stops After the reference point is reached the reciprocator begins to carry out the movements set on the reciprocator control unit Before the horizontal axis is put into operation the travel distance must be set on the axis control unit see therefore the corresponding axis control unit operating manual Warning N Incorrect setting of the travel distance can cause damages t
11. en loose rollers 13 12 14 XT carriage rollers In this case proceed as follows 1 Switch off the electric power Remove the carriage and the panels Loosen the roller screw 14 lightly Loosen the lock nut 12 Or E N Adjust the roller pressure with the screw 13 in such a way that the roller can just be turned by hand o Tighten the roller screw 14 Tighten the lock nut 12 8 Fit the panels again and fasten them firmly The carriage should run evenly and quietly again XT10 Maintenance e 29 voli Gema Decommissioning storage Introduction XT10 Safety rules Before lifting a reciprocator off of its horizontal axes it must be secured from falling over with a lifting device such as a crane fork lift etc The point of attachment is the eye bolt A at the top of the reciprocator ZA reciprocator Top view The horizontal axes should be lifted up using lifting straps Requirements on personnel carrying out the work All work should be carried out only by authorized technical personnel Decommissioning storage e 31 Gema V 02 13 Storage conditions 32 e Decommissioning storage Type of storage Horizontal axes can be stacked Storage duration If the physical conditions are maintained the unit can be stored indefinitely Space requirements The space requirements correspond to the sizes of the axes of motion The load bearing capacity of the floor should be at
12. ength 5 3 XT10 Horizontal axis electrical module in the ZA05 Reciprocator 48 e Spare parts list XT10 oe Gema XT10 Spare parts list e 49
13. eversing points as well as the maximum travel distance Each time the reciprocator is switched on the control unit requests that the carriage travels to the reference point zero point The carriage travels to the mechanical stop which means onto the rubber buffer The control unit notes this and gives the distance how far the carriage must travel from this position to decompress the rubber buffer The standard value for the XT axis is 30 that means 30 mm away from the mechanical stop For this reason the Axis control unit must be programmed in such a way that the reference point is always 30 mm before the lowest mechanical stop zero point Attention In order to avoid damages to the booth to the gun holders etc the reference point must be set before the first start up Rubber buffer E Li A ul XT10 horizontal axis reference point and mechanical stops Warning In order to avoid damages to the booth or the gun holders the reference point must be checked before the first start up and if necessary reset It must be noted that the axes in reference travel moves up to 30 mm behind the control s zero point Warning The reference point must be referenced before each start up at each switching on after an interruption of the power supply etc Start up e 23 Gema Initial start up A A 24 e Start up V 02 13 Danger Never stand on the horizontal axis or under the carriage of the vertical a
14. he contamination of the enclosure strong contamination on the outside can increase the operating temperature of the drive unit Therefore clean the drive unit from time to time with a vacuum cleaner etc Check the drive unit gearbox monthly for oil loss Ifthe drive unit gearbox has to be changed for any reason the complete unit has to be replaced XT10 ui Gema Replacing the drive unit WARNING There is the risk of burns if contact is made with electrical components that have become overheated All work must be carried out only by technical personnel and when no power is applied If it is necessary to replace a drive unit gearbox the complete motor unit must be dismantled from the horizontal axis Therefore the horizontal axis has to be free of load and disconnected from mains a 24 Le XT10 Horizontal axis drive unit Procedure 1 o ot lo N 10 11 Remove the Z axis from the carriage plate Remove the carriage plate Remove both cover panels Loosen the tensioning screws so that the drive belt is slack Remove the drive belt Uncouple the motor power supply cable in order to use it with the new motor again Remove the incremental pulse generator 8 Loosen the fixing screws 12 4 pieces and take out the motor drive unit Loosen the screws 24 and remove the guide rollers 20 Loosen the clamping set 16 and remove the drive wheel Loosen the screws 14 and remove the holder from the
15. ies Firmly anchor the horizontal axis to the floor if it is not mounted to another axis of motion Warning The movement of the reciprocator can cause injuries Erect a protective fence around the reciprocator so that there is no danger of injury during normal operation Danger Injuries can occur inside the protective fence due to the movement of the reciprocator In order to enter the inner area the door interlocks must be released by the control unit This release signal may only be activated by technical personnel Except for normal operation all other operating modes must be set up by an authorized technical representative Set up assembly and commissioning e 15 A Gema Design and function Mechanical structure The XT10 Horizontal axis consists of the following components XT10 Horizontal axis mechanical structure 1 Drive unit complete 4 Frame 2 Leveling bolt 5 Rubber buffer 3 Baseboard 6 Carriage XT10 Design and function e 17 Gema d Function description The XT10 Horizontal axis is a feeding axis for adjusting the gun position to the parts to be coated The XT10 Horizontal axis position detection takes place by a pulse generator installed onto the drive unit The drive takes place by the drive unit installed onto the axis carriage motor with spur gear and pulse generator and the toothed belt installed into the travel frame Safety and monitoring devices All moving axes must b
16. ing the XT10 Horizontal axis to the ZA reciprocator Preparation for Start Up i General information nnne en nesr en nennen nennen nenene Reference point ersehen Electrical connections cable connections Checkpoints before switching on 200 nnnnnnnnennnnnnnnn Grounding protection type Hoses and Cables arica Haaren Reference point and mechanical Stops nn Initial Start up Avie anna iaia Gema Table of contents e 3 Gema V 02 13 Maintenance 25 General informationi 3 sarta initial 25 Maintenance schedule iii 26 Driveunit eletti ail tia 26 Replacing the drive Unit 27 Drive Delia aci dialetti atea 28 Tensioning the drive belt ii 28 Gounterrollers tizs scienze dia ia aden tee 29 Decommissioning storage 31 INTFOGUGHON aa een keines adas 31 Safety ul ccoo 31 Requirements on personnel carrying out the Work 31 Storage CONDITIONS vei ccsccestsccscceessereeadarenencacaenet satcenekcedaaaetastecnnssecpeeadd taeceeetadaaeseataates 32 Type 0f t rage cauneeieen tania 32 storage dur tion css 32 Space requirement iiuniiaolonia alal alli 32 Physical requirements 32 Hazard NOIES ui Eis 32 SNUL AOWN a ld aiar 33 DECOMMISSION cid dass 33 A ON 33 Maintenance during storage crono nn nr rnna nn nr naar rra 33 Maintenance schedule
17. ions as well as other generally recognized safety regulations occupational health and structural regulations are to be observed 7 Furthermore the country specific safety regulations also must be observed Explosion protection Protection type C Ex 113D add A summary of the directives and standards European directives RL 94 9 EWG Equipment and Protective Systems Intended for Use in Potentially Explosive Atmospheres 2004 108 EG Electromagnetic Compatibility EMC EN European standards Safety of Machinery Basic Concepts General Principles for Design Part 1 Basic Terminology Methodology EN ISO 12100 2 Safety of Machinery Basic Concepts General 2004 Principles for Design Part 2 Technical Principles EN ISO 14121 1 Safety of Machinery Risk Assessment Part 1 2007 Principles or Safety of Machinery Electrical Equipment of Machines en Part 1 General requirements EN ISO 12100 1 2004 Potentially Explosive Atmospheres Application of EN 13980 2002 Quality Systems n an Quality Management Systems Requirements rs Electrical Apparatus for Use in the Presence of ds Combustible Dust General requirements EN 61241 2 2 Electrical Apparatus for Use in the Presence of 1995 Combustible Dust Part 2 Methods i Gema Electrical Apparatus for Use in the Presence of Combustible Dust Part 10 Classification of Areas Where Combustible Dusts Are or May Be Prese
18. istance Operation without the proper training Operating the horizontal axis without the protective fence XT10 V 02 13 Technical data Gema XT10 Horizontal axis XT10 Electrical data XT10 Power supply 230 VAC from control unit Tolerance 10 Power consumption 0 3 KW Frequency 50 60 Hz Protection type IP54 Isolation Class F Control unit CM 30 Temperature range 1 G 90 C 50 F 104 F Mechanical data XT10 Speed 0 01 0 6 m s Acceleration 0 1 2 0 m s Position detection with incremental pulse generator Reference point corresponds to the zero point Zero point selectable in both end positions Travel distance min 400 mm Travel distance max on request Technical data e 13 Gema on Dimensions 750 50 Free space Horizontalachse XT10 Abmessungen Versions The XT10 Horizontal axis is available in two versions with different travel distances 14 e Technical data XT10 10 XT10 14 Travel distance length 1000 mm 1400 mm Weight 150 kg 166 kg XT10 uti Gema Set up assembly and commissioning gt gt XT10 Warning If a free standing horizontal axis is not anchored firmly to the floor uncontrolled movement of the machine or insufficient stability can cause injur
19. least 200 kg m There are no special requirements concerning distance to neighboring equipment Physical requirements Storage must be inside a dry building at a temperature between 5 50 C Hazard notes There is no danger to personnel or the environment if the unit is stored properly XT10 Shut down do Gema Decommissioning Before starting any kind of work the axes of motion must be disconnected from the power supply Unplug the power cable Unplug the ground cable Cleaning The running surfaces of horizontal axis must be thoroughly cleaned Maintenance during storage XT10 Maintenance schedule No maintenance schedule is necessary Maintenance works During long term storage periodically perform a visual check for corrosion Decommissioning storage e 33 i Gema Packing transport Introduction This chapter describes special precautions that must be taken during internal transport of the product if the customer himself must pack transport and ship the product such as to have renovations or service work carried out by the manufacturer or the product must be shipped for disposal recycling Requirements on personnel carrying out the work All work must be carried out by personnel trained in packing machines Packing material Selection of packing material Suitably stable wood packing material must be used Procedure when packing Transport the unit only in a horizo
20. mm 214 108 13 Ribbed washer M10 237 981 14 Countersunk Allen screw M6x25 mm 241 598 15 Toothed belt wheel 1003 814 16 Clamping set 20 47x22 mm 257 583 17 Spacer ring 20 12 1x3 7 mm 1003 795 18 Deep groove ball bearing Y 12 32x10 mm 245 720 19 Snap ring A 32 235 741 20 Guide roller 1003 793 21 Spacer ring 20 12 1x25 mm 1003 812 22 Roller fixing plate L 120 mm 1003 796 23 Ribbed washer M12 237 973 24 Hexagon screw M12x80 mm 221 325 1 If these parts must be replaced clean off all grease before assembly 42 e Spare parts list XT10 ui Gema Drive unit 15 16 22 e 21 23 14 Fre u 24 le 37 A ie amp 13 Jf amp 17 r O PA 20 x XT10 Horizontal axis drive unit 19 18 XT10 Spare parts list e 43 Gema Vons Running wheel bearing Running wheel bearing complete FS 1003 808 Running wheel bearing complete LS 1003 806 1 Running wheel bearing support FS 1003 809 1 Running wheel bearing support LS 1003 807 3 Counter roller 390 658 4 Bearing bolt 1003 813 5 Running wheel Y 73 mm 1003 805 6 Deep groove ball bearing 10 35x11 mm 201 359 7 Deep groove ball bearing 15 52x15 mm 258 415 8 Snap ring l 35 216 135 9 Snap ring A 10 256 358 10 Snap ring A 25 237 094 11 Ribbed washer M8 242 870 12 Hexagon nut M6 205 095 13 Hexagon screw M6x25 mm 213 845 14 Hexagon screw M8x10 mm 213 900 Wearing part O
21. mum height of the booth gun slots If an incorrect too high stroke limit is set this can lead to damage to the vertical axis and or the booth Warning During a test run it must be guaranteed that the unit is not damaged N by the test In particular the limitations of the stroke range have to be observed for further information see chapter Setting the upper mechanical stop XT10 General safety regulations e 7 Gema V 02 13 When repairing the horizontal axis both the axis control unit and the horizontal axis must be disconnected from the mains according to the local safety regulations Repairs may be done only by authorized Gema service centers Unauthorized conversions and modifications can lead to injuries and damage to the equipment The Gema Switzerland GmbH guarantee would no longer be valid Only original Gema spare parts should be used The use of spare parts from other manufacturers will invalidate the Gema guarantee conditions We point out that the customer himself is responsible for the safe operation of the equipment Gema Switzerland GmbH is in no way responsible for any resulting damage i Gema About this manual General information XT10 This operating manual contains all the important information you require for the working with the XT10 horizontal axis It will safely guide you through the start up process and give you references and tips for the optimal use of your new powder coating system
22. nt EN 61241 10 2004 re Explosive Atmospheres Basic Concepts and EN 1127 1 2008 Methodology Product specific safety measures XT10 Horizontal axis The XT10 Horizontal axis is a constituent part of the system and is thus integrated into the safety system of the plant If it is to be used in a manner outside the scope of the safety concept then corresponding measures must be taken Note For further information see the more detailed Gema safety regulations Special safety regulations for XT10 horizontal axis 1 The XM11 Horizontal axis may only be switched on and operated after careful reading of this manual Incorrect operation of the axes control unit can lead to accidents malfunctions or damage to the plant 2 Attention the power of the horizontal axis is very much stronger than that of a human being All axes must be secured against access during operation see local regulations Never stand under the Z carriage when the horizontal axis is not operating 3 The plugs and sockets of the axes control unit and the power unit of the XT10 horizontal axis should only be unplugged when the power supply is disconnected 4 The connecting cables between the control unit and the horizontal axis must be laid in such a way that they cannot be damaged during axes operation Please observe the local safety regulations 5 The maximum upper stroke limit of the reciprocator must always be set with reference to the maxi
23. ntal position Transport Data concerning goods to be transported The space requirements correspond to the size of the axes of motion plus the packaging Loading transferring the load unloading At least one fork lift must be available XT10 Packing transport e 35 V 02 13 Fault clearance Troubleshooting Warning Gema Faults may be fixed by trained personnel only Error fault Procedures remedy Reciprocator with carriage plate is waggling Check the connecting bolts between reciprocator carriage plate and the carriage for tightness Adjust the counter rollers without clearance by the corresponding screws on the running wheel bearing guide wheel bearing see also the spare parts list Warning In no case press the counter rollers otherwise they wear quickly Reference point not reached Remove the powder accumulation on the running surfaces Check for a foreign body if present remove it Check the XT10 Horizontal axis for proper running move manually Consider the indications in the axes control unit operating manual XT10 Fault clearance e 37 nn Gema Spare parts list Ordering spare parts When ordering spare parts for powder coating equipment please indicate the following specifications Type and serial number of your powder coating equipment Order number quantity and description ofeach spare part Example Type XT10 Serial number 1234 5678
24. o the reciprocator to the booth and or to the applicators XT10 Start up e 21 Gema en Electrical connections cable connections Electrical module Electrical module CM 30 control XT10 connections O Note 1 All internal connections between the XT10 axis and the electrical module are to be made according to the enclosed wiring diagram Checkpoints before switching on Before switching on the following checks should be done Check if the cables and hoses are laid out correctly Check if the guns have a clear run and do not touch the booth slots Check the distance between the work pieces and the guns Warning Before connecting or switching on the horizontal axis read carefully these operating instructions Grounding protection type All metal parts of the horizontal axis must be grounded according to the local safety regulations The grounding screw is located on the horizontal axis base All electrical installations are implemented in accordance to VDE IP54 protection type regulations 22 e Start up XT10 ut Gema Hoses and cables All movable hoses and cables must be laid out in such a way that they are neither subjected to any loads nor can hang on other parts The electric cables of the reciprocators must be protected from mechanical damage Reference point and mechanical stops XT10 gt gt The reference point serves as starting point for the axis control unit for calculating the r
25. proper use of the equipment could damage the machine or cause it to malfunction Possible consequences minor injuries or damage to equipment INFORMATION Useful tips and other information Conformity of use XT10 1 The XT10 is built to the latest specification and conforms to the recognized technical safety regulations and is designed for the normal application of powder coating 2 Any other use is considered non compliant The manufacturer shall not be liable for damage resulting from such use the user bears sole responsibility for such actions Gema Switzerland GmbH must be consulted prior to any use of the XT10 for any purposes or substances other than those indicated in our guidelines 3 Observance of the operating service and maintenance instructions specified by the manufacturer is also part of conformity of use The XT10 should only be used maintained General safety regulations e 5 Gema n and started up by trained personnel informed about and familiar with the possible hazards involved 4 Start up i e the execution of a particular operation is forbidden until it has been established that the XT10 horizontal axis has been set up and wired according to the guidelines for machinery 2006 42 EG EN 60204 1 machine safety must also be observed 5 Unauthorized modifications to the XT10 horizontal axis exempt the manufacturer from any liability from resulting damage 6 The relevant accident prevention regulat
26. s or use of this publication and reserves the right to revise this publication and make changes to its content without prior notice Printed in Switzerland Gema Switzerland GmbH M venstrasse 17 9015 St Gallen Switzerland Phone 41 71 313 83 00 Fax 41 71 313 83 83 E Mail info gema eu com Homepage www gemapowdercoating com V 02 13 Table of contents XT10 General safety regulations Safety symbols pictograms Conformity Of USE nn A summary of the directives and standards Product specific safety measures nennen XT10 Horizontal axis nn nsseerrnnn nensem Special safety regulations for XT10 horizontal axis About this manual General information nono nanannn cnn nono nanacannnannna Function description Field of application narran Special characteristiCS nn Reasonably foreseeable MISUSE Technical data XT 10 Hlorizontalaxis H222 tito aan Electrical data nn Mech nical data 222 2 r ee ee DIMENSIONS Areale ga WERSIONS 07 clothe cA at a Set up assembly and commissioning Design and function Mechanical structure 4 2 0 24448 ladra fiera Function description iy ccc siii Safety and monitoring devices Start up Assembly of the XT10 Horizontal axis en Connect
27. xis when it is in operation Danger of accident Warning The power of the horizontal axis is much stronger than that of a human being AII axes must be secured against admittance during operation see local regulations Before start up the horizontal axis the following points must be noted The frame and the drive carriage of the axis must be grounded The grounding of the frame must be done by the customer Adapt the system parameters in the axes control unit see the axes control unit operating instructions In addition the following checks are necessary before the initial start up Travel distance Check by moving manually as well as in accordance to the axes control operating manual Control unit Check the cable connections correct connections squeezed parts cable lengths cable movement etc Stability Horizontal axis and carriage plate must be stable XT10 m Gema Maintenance A Danger Injuries can occur inside the protective fence due to the movement of the reciprocator In order to enter the inner area the door interlocks must be released by the control unit This release signal may only be activated by technical personnel General information A XT10 Warning Before maintenance work can be carried out on the horizontal axis it must be ensured that the horizontal axis cannot be turned on by third parties The horizontal axis has to be free of load and disconnected from mains
Download Pdf Manuals
Related Search