Home
DJ Lase GR-140 RGY MKII showlaser user manual
Contents
1. 53 Notes th mann showlaser MUSIC IS OUR PASSION 54 Musikhaus Thomann e K Treppendorf 30 96138 Burgebrach Germany www thomann de
2. Check the mains power connection and the main fuse Check the safety key switch 8 re No response to DMX controller If the display indicates a flashing figure e g 001 no DMX signal is received Check the DMX connections and cables for proper connection If the display is not flashing and the unit does not respond check the address settings and the DMX polarity Try to use another DMX controller ree Check to see if the DMX cables run near or alongside to high voltage cables that may cause damage or interference to DMX interface circuits If the procedures recommended above do not succeed please contact our Service Center You can find the contact information at www thomann de DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 49 Cleaning 11 Cleaning DANGER Laser radiation During cleaning follow the instructions specified in amp Chapter 2 Safety instruc tions on page 11 To avoid laser emission remove the safety key before you start to clean the device Optical lenses Clean the optical lenses that are accessible from the outside regularly in order to optimize the light output The frequency of cleaning depends on the operating environment wet smoky or particularly dirty surroundings can cause more accumulation of dirt on the optics of the device Clean with a soft cloth using our lamp and lens cleaner item no 280122 Always dry the parts carefully th mann
3. 3 Menu diagram DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 39 Operation 7 4 Functions in DMX mode Channel 1 Value Mode selection 0 50 51 100 101 150 151 200 201 255 themann MUSIC IS OUR PASSION 40 Function Laser off Auto show Sound controlled automatic show DMX 1 mode DMX 2 mode showlaser Channels 2 to 5 in DMX 1 mode Channe Value I 2 Pattern rotation 0 4 527 128 133 134 255 0 255 Red laser 0 4 5 10 11 254 255 Operation Function No rotation Clockwise rotation slow to fast No rotation Counterclockwise rotation slow to fast Vibration effect of patterns small to large vibration Laser off Laser on Strobing strobe effect slow to fast Sound controlled strobe effect DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 41 Operation Channe Value l 5 Green laser 0 4 5 10 11 254 255 th mann MUSIC IS OUR PASSION 42 Function Laser off Laser on Strobing strobe effect slow to fast Sound controlled strobe effect showlaser Operation Channels 2 to 5 in DMX 2 mode Channe Value Function I 2 Pattern rotation 0 4 No rotation 527 Clockwise rotation slow to fast 128 133 No rotation 134 255 Counterclockwise rotation slow to fast 3 0 255 Vibration effect of patterns small to large vibration 4 Colour selection 0 4 Laser off 5 20 Constantly red 21 35
4. showlaser MUSIC IS OUR PASSION 50 Protecting the environment 12 Protecting the environment Disposal of the packaging mate rial For the transport and protective packaging environmentally friendly materials have been chosen that can be supplied to normal recycling Ensure that plastic bags packaging etc are properly disposed of Do not just dispose these materials with your normal household waste but make sure that they are fed to a recovery Please follow the notes and markings on the packaging Disposal of batteries Batteries must not be disposed of as domestic waste or thrown into fire Dispose of the bat teries according to national or local regulations regarding hazardous waste To protect the environment dispose of empty batteries at your retail store or at appropriate collection sites DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 51 Protecting the environment Disposal of your old device This product is subject to the European Waste Electrical and Electronic Equipment Directive WEEE Do not dispose with your normal household waste Dispose this device through an approved waste disposal firm or through your local waste facility When discarding the device comply with the rules and regulations that apply in your country If in doubt consult your local waste disposal facility th mann showlaser MUSIC IS OUR PASSION 52 Notes DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION
5. the built in show programme press ENTER The display shows S 0 Use the UP and DOWN buttons to select the settings S 0 sensitivity 0 sound controlled mode off or S 7 low sensitivity to S 9 high sensitivity Press ENTER to store the setting Please note that the laser is switched off if a sound controlled show has been selected but the microphone does not receive any sound Press FUNC until the display shows SLA In this mode the device exactly follows the opera tion of the master it is connected to Press ENTER to confirm and to start the operation in Master Slave mode Press FUNC until the display shows 001 You can now set the number of the first DMX channel used by the device DMX address Use the UP and DOWN buttons to select a value between 1 and 507 Press ENTER to store the value and to start the operation in DMX mode Ensure that this channel number fits to the configuration of your DMX controller DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 37 Operation Press FUNC until the display shows rEN Press ENTER to confirm and to start operation in Remote control mode This mode allows you to operate the device conveniently with the infrared remote control Make sure that the infrared receiver on the front panel of the device is not obstructed Remote control mode th mann showlaser MUSIC IS OUR PASSION 38 Operation 7
6. themann MUSIC IS OUR PASSION 10 11 12 Plug and connection assignMent cccsscsssscssssessecsscecsscceseecsseceseecssscesaeessscecuecssceeaneeeseeesies 47 Troublesho0ting run ana an een a nein 48 GIEaNIN Ge Eee Irre 50 Protecting the environment usneseennssennseunssennsennssensssnnsssnnssnnnssunssenssennssenssnnnnsnnnssenne 51 showlaser 1 General notes General notes This manual contains important instructions for the safe operation of the unit Read and follow the safety instructions and all other instructions Keep the manual for future reference Make sure that it is available to all those using the device If you sell the unit please make sure that the buyer also receives this manual Our products are subject to a process of continuous development Thus they are subject to change DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION General notes 1 1 Further information On our website www thomann de you will find lots of further information and details on the following points Download This manual is also available as PDF file for you to download Use the search function in the electronic version to find the topics of Keyword search interest for you quickly Our online guides provide detailed information on technical basics Online guides and terms Personal consultation For personal consultation please contact our technical hotline If you have any proble
7. Built in automatic show programmes Sound control Master slave mode Laser diodes Red 100 mW green 40 mW showlaser 18 4 Installation Installation Unpack and carefully check that there is no transportation damage before using the unit Keep the equipment packaging To fully protect the device against vibration dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage respectively You can install the device on the wall or on the ceiling Amounting bracket and the required screws are provided together with the device DANGER Laser radiation During installation follow the instructions in amp Chapter 2 Safety instructions on page 11 To avoid laser emission remove the safety key before you start to install the device DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 19 Installation WARNING Stray laser radiation Inadequately secured additional components may cause stray laser radiation Make sure that all additional components are adequately secured WARNING Risk of injury caused by falling objects Make sure that the installation complies with the standards and rules that apply in your country Always secure the device with a secondary safety attachment such as a Safety cable or a safety chain th mann showlaser MUSIC IS OUR PASSION 20 Installation NOTICE Risk of overheating
8. OUR PASSION 11 Safety instructions Laser safety basics themann MUSIC IS OUR PASSION Laser safety requirements are based on DIN EN 60825 1 The corresponding accident preven tion regulation of the Accident Prevention and Insurance Association in Germany is BGV B2 This device contains a class 3B laser It is equipped with a safety key Always remove the key when the device is not attended by a trained operator As an operator you are responsible for the safety of all persons present Familiarize yourself with the laser safety regulations that apply in your country To ensure safe operation it is important to pay attention to the following instructions Prior to commissioning the company operator must appoint a qualified person as laser pro tection officer in writing and notify the operation of the laser equipment to the Accident Pre vention and Insurance Association and to the authority responsible for occupational safety In the event of public use the complete laser equipment must be approved by an expert e g the Technical Control Board TUV prior to commissioning showlaser 12 Safety instructions Safety DANGER Danger for children Ensure that plastic bags packaging etc are disposed of properly and are not within reach of babies and young children Choking hazard Ensure that children do not detach any small parts e g knobs or the like from the unit They could swallow the pieces and choke Ne
9. Red off constantly green 36 50 Red and green constantly DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 43 Operation Channe Value 51 80 81 110 111 140 141 170 171 200 201 255 5 Strobing strobe effect 0 4 5 254 255 th mann MUSIC IS OUR PASSION Function Strobe effect for red green off Red off strobe effect for green Strobe effect for red and green Constantly red strobe effect for green Strobe effect for red constantly green Alternating strobe effect for red and green No function Strobing strobe effect slow to fast Sound controlled strobe effect showlaser 8 Technical specifications Laser medium Laser power Laser classification acc to EN 60825 1 2007 Beam diameter at outlet aperture Pulses Divergence per beam Divergence overall light Number of DMX channels Operating voltage supply Fuse Technical specifications Red 650 nm typical LD GaAlAs Green 532 nm typical DPSS Nd YVO4 Red 100 mW Green 40 mW 3B lt 5mm All pulses lt 4 Hz gt 0 25 s lt 2 mrad lt 160 5 AC 110 240 V 50 60 Hz 5 mm x 20 mm 1 6 A 250 V slow blow th mann MUSIC IS OUR PASSION DJ Lase GR 140 RGY MKII 45 Technical specifications 15W 145 mm x 160 mm x 80 mm Power consumption Dimensions W x D x H Weight 1 8kg th mann showlaser MUSIC IS OUR PASSION 46 Plug and connection assignments 9 Plug and con
10. S TeV DJ Lase GR 140 RGY MkII showlaser th mann user manual MUSIC IS OUR PASSION Musikhaus Thomann e K Treppendorf 30 96138 Burgebrach Germany Telephone 49 0 9546 9223 0 E mail info thomann de Internet www thomann de 24 01 2014 ID 255628 Table of contents Table of contents 1 Generalin tes u 00 isdn nennen snenne on landeederen nen aradnner odeachsousoseteadbicctasestion 5 1 1 Further information 1 2 Notational conventions 7 1 3 Symbols and signal WOrdS ssscsssscsssecsseecsssecsnssesssscsseesssccsssessescessseecasecssseeesceesseecsneessncesseeesaeentes 9 2 Safety instructions iaiia 11 3 Features desde ssctescesedsovstntssvonvervectoutosvesseeusnscusteesdvesGserssetlvebssysidseverinctesdeiboevacbond asuvsdey uaaa aSa 18 4 Installation PA R EEA R S 19 5 Starting UP peier aen ea Aae ts sossstssdestes ace sacessteseeouncostcesvesecctases Ear aE 23 6 Connections and controls E E E 27 7 Operation 7 1 Start US DOV IGS A A E E EE 7 2 MAMAS IU sar sicssstsstkovencsetensstiectaesvusconsevasensevdsopendesipetdersbessoseissbavedsosends iseadesvastaebstissnnsb seresbedusebabetaseosvs 73 Menu diagram oa 7 4 Functions in DMX mode 8 Technical specifications cccccesssssssssssssssssssecssessssssesssssssessesssscsscsssecsucssscsnecsscssucssscsnsssscessessseeses 45 DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION Table of contents
11. Starts a sound controlled automatic show in random order AUTO button Starts an automatic show in random order Changes the patterns used for the colours red green red green Stops or restarts a running show A button Switches the flash effect for the red laser on or off the flash frequency can be input with the numeric keypad DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 33 Connections and controls 26 27 28 29 30 B button Switches the flash effect for the green laser on or off the flash frequency can be input with the numeric keypad C button No function Numeric keypad for direct input of values flash frequency motor speed speed of the double burst grating effect Controls the motor speed of the laser optics in conjunction with the numeric keypad button Controls the double burst grating effect in conjunction with the numeric keypad th mann showlaser MUSIC IS OUR PASSION 34 7 Operation 7 1 Startthe device Operation Perform the following steps to start the operation Ja 5 Verify that all required laser safety precautions have been taken Make sure that there is no one in the reach of the laser beam Insert the safety key into the lock 8 and turn it into the OFF position If not already connected connect the device to the mains 6 Using the main switch 5 turn the device on After a few seconds the fan and the motors start to wo
12. The distance between the light output and the illuminated surface must be more than 0 5 m 19 7 in Always ensure sufficient ventilation The ambient temperature must always be below 40 C 104 F DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 21 Installation Inserting the battery into the remote control themann MUSIC IS OUR PASSION Press the lock of the battery holder to the centre of the housing and pull out the battery holder like a drawer Insert the battery The battery is correct if the positive pole points to the housing base of the remote control Slide the battery holder back into the remote until it clicks into place When shipping the battery is already installed in the remote and protected against discharge by a transparent plastic foil Remove the plastic foil prior to first use showlaser 22 5 Starting up Starting up Establish all connections as long as the unit is switched off Use the shortest possible high quality cables for all connections DANGER Laser radiation When starting up the device you have to follow the instructions given here Chapter 2 Safety instructions on page 11 DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 23 Starting up NOTICE Possible data transmission errors For error free operation make use of dedicated DMX cables and do not use ordi nary microphone cables Never connect the DMX input or output to audio dev
13. f the remote control th mann showlaser MUSIC IS OUR PASSION 28 Connections and controls Rear panel WARNING THIS APPLIANCE MUST BE EARTHEB g z i MAINS 100 240Vac50 60Hz12W FUSE 1A 250Vac low DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 29 Connections and controls 5 Power switch 6 Plug for mains cable with fuse holder next to it The input voltage range is printed below the plug 7 INPUT DMX input 8 LOCK Safety key switch Turns the laser output on or off 9 Eyelet for safety cable 10 FUNC button Opens the main menu 11 UP button Increments the displayed value by one 12 DOWN button Decrements the displayed value by one th mann showlaser MUSIC IS OUR PASSION 30 15 16 ENTER button Chooses between the options of the selected mode MIC Microphone used for the sound mode Display OUTPUT DMX output DJ Lase GR 140 RGY MKII Connections and controls themann MUSIC IS OUR PASSION 31 Connections and controls Remote control Laser Remote th mann showlaser MUSIC IS OUR PASSION 32 20 21 22 23 24 25 Connections and controls ON OFF button When the device is in the Auto Show mode or is performing a self test press the button for several seconds to enter the Remote control mode When the device is already in the Remote control mode this button switches the laser on or off MUSIC button
14. ices such as mixers or ampli fiers th mann showlaser MUSIC IS OUR PASSION 24 Starting up Connections in DMX mode Connect the DMX input of the device to the DMX output of a DMX controller or another DMX device Connect the output of the first DMX device to the input of the second one and so on to form a daisy chain Always ensure that the output of the last DMX device in the daisy chain is terminated with a resistor 1100 1 4 W 2 cco n DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 25 Starting up Connections in master slave mode themann MUSIC IS OUR PASSION When you configure a group of devices in master slave mode the first unit will control the other units for an automatic sound activated synchronized show This function is ideal when you want to start a show immediately Connect the DMX output of the master device to the DMxX input of the first slave device Then connect the DMX output of the first slave device to the DMX input of the second slave device and so on showlaser 26 Connections and controls 6 Connections and controls Front panel DJ Lase GR I40 RGY MKII Brea e g AGS es DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 27 Connections and controls 1 Laser aperture 2 LED POWER Shows that the device is turned on 3 LED MUSIC Shows that a sound or music signal is being detected 4 IR Receiver for the infrared signal o
15. ms with the device the Service A i customer service will gladly assist you th mann showlaser MUSIC IS OUR PASSION General notes 1 2 Notational conventions This manual uses the following notational conventions Letterings The letterings for connectors and controls are marked by square brackets and italics Examples VOLUME control Mono button Displays Texts and values displayed on the device are marked by quotation marks and italics Examples 24ch OFF DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION General notes Instructions The individual steps of an instruction are numbered consecutively The result of a step is indented and highlighted by an arrow Example 1 _ Switch on the device 2 Press Auto gt Automatic operation is started 3 Switch off the device Cross references References to other locations in this manual are identified by an arrow and the specified page number In the electronic version of the manual you can click the cross reference to jump to the specified location Example See Cross references on page 8 th mann showlaser MUSIC IS OUR PASSION 1 3 Symbols and signal words General notes In this section you will find an overview of the meaning of symbols and signal words that are used in this manual Signal word DANGER WARNING NOTICE DJ Lase GR 140 RGY MKII Meaning This combination of symbol and signal
16. nection assignments Introduction This chapter will help you select the right cables and plugs to connect your valuable equip ment so that a perfect light experience is guaranteed Please take our tips because especially in Sound amp Light caution is indicated Even if a plug fits into a socket the result of an incorrect connection may be a destroyed DMX controller a short circuit or just a not working light show DMX connections The unit offers a 3 pin XLR socket for DMX output and a 3 pin XLR plug for DMX input Please refer to the drawing and table below for the pin assignment of a suitable XLR plug Pin Configuration 1 Ground shielding 2 Signal inverted DMX cold signal 3 Signal DMX hot signal DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 47 Troubleshooting 10 Troubleshooting DANGER Laser radiation inside the housing During troubleshooting you have to comply with the instructions given here Chapter 2 Safety instructions on page 11 Any servicing of the unit with open housing must only be carried out by quali fied technicians For working on the device you have to wear suitable laser safety goggles In the following we list a few common problems that may occur during operation We give you some suggestions for easy troubleshooting th mann showlaser MUSIC IS OUR PASSION 48 Troubleshooting The unit does not work no light the fan does not run
17. radiation free from flammable substances DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 15 Safety instructions NOTICE Risk of fire Do not cover the device nor any ventilation slots Do not place the device near any direct heat source Keep the device away from naked flames NOTICE Operating conditions This device has been designed for indoor use only To prevent damage never expose the device to any liquid or moisture Avoid direct sunlight heavy dirt and strong vibrations th mann showlaser MUSIC IS OUR PASSION 16 Safety instructions NOTICE Power supply Before connecting the device ensure that the input voltage AC outlet matches the voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker Failure to do so could result in damage to the device and possibly injure the user Unplug the device before electrical storms occur and when it is unused for long periods of time to reduce the risk of electric shock or fire DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 17 Features 3 Features themann MUSIC IS OUR PASSION The showlaser is specially suited for discos clubs bars small stages etc It allows smooth inte gration into light shows but can also be operated as stand alone device Special features of this device Control via DMX 5 channels infrared remote control and buttons plus display on the unit itself
18. rk The display shows the current operation mode The device is now opera tional Turn the safety key 8 to the ON position to turn the laser beam on DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 35 Operation 7 1 1 Stop the device 7 2 Main menu themann MUSIC IS OUR PASSION 1 Turn the safety key 8 to the OFF position to turn the laser beam off and remove the key Keep the safety key under control 2 Using the main switch 5 turn the device off 3 gt Optionally disconnect the device from the mains 6 Press FUNC to activate the main menu and to select one of the operation modes When the display flashes use the UP and DOWN buttons to change the displayed value When the display shows the desired value press ENTER To go back to the main menu without any changes press FUNC or wait for one minute All previously made settings are saved even if you disconnect the device from the power supply showlaser 36 Auto show mode Master Slave mode DMX mode Operation Press FUNC until the display shows Aut The device operates in stand alone mode and dis plays a pre programmed show that can optionally be controlled by the built in microphone Use the UP and DOWN buttons to select the built in show programme with or without sound control display Sou or Aut To set the sensitivity and thus the response characteristic of the microphone for
19. ver let children unattended use electrical devices DANGER Electric shock caused by high voltages inside Within the device there are areas where high voltages may be present Never remove any covers A There are no user serviceable parts inside DJ Lase GR 140 RGY MKII th mann MUSIC IS OUR PASSION 13 Safety instructions themann MUSIC IS OUR PASSION DANGER Electric shock caused by short circuit Always use proper ready made insulated mains cabling power cord with a pro tective contact plug Do not modify the mains cable or the plug Failure to do so could result in electric shock death or fire If in doubt seek advice from a regis tered electrician DANGER Laser radiation avoid exposure to beam The device contains a class 3B laser classified according to EN 60825 1 Do not look into the laser beam The laser beam can injure your eyes when you directly look into it Do not expose yourself to the laser beam The laser beam can cause skin burns In this context take extreme care when using converging optical instruments showlaser 14 Safety instructions WARNING Eye damage caused by high light intensity Never look directly into the light source WARNING Risk of epileptic shock Strobe lighting can trigger seizures in photosensitive epilepsy Sensitive persons should avoid looking at strobe lights NOTICE Laser radiation risk of fire o Keep the area exposed to laser
20. word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided This combination of symbol and signal word indicates a possible dangerous situation that can result in death or serious injury if it is not avoided This combination of symbol and signal word indicates a possible dangerous situation that can result in material and environmental damage if it is not avoided themann MUSIC IS OUR PASSION General notes themann MUSIC IS OUR PASSION 10 Warning signs gt eee showlaser Type of danger Warning high voltage Warning laser radiation Warning suspended load Warning danger zone Safety instructions 2 Safety instructions Intended use This device is intended to be used for the projection of laser light effects It has been designed exclusively for show applications Use the device only as described in this user manual Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage No liability will be assumed for damages resulting from improper use This device may be used only by persons with sufficient physical sensorial and intellectual abilities and having corresponding knowledge and experience Other persons may use this device only ifthey are supervised or instructed by a person who is responsible for their safety DJ Lase GR 140 RGY MKII th mann MUSIC IS
Download Pdf Manuals
Related Search
Related Contents
USER MANUAL - Kramer Electronics 660 lb. Table Lift American Audio X-CALIBUR User's Manual 仕 様 PDFファイル Extech 475055 High Capacity Force Gauge w/ PC Solar Square Deck Light 0819 - Garden NAD Electronics FWC555 User's Manual Copyright © All rights reserved.
Failed to retrieve file