H Series——MiNi High Speed Dome IP Camera
Contents
1. once the IP camera was connected into the LAN it will communicate with the router of the LAN It will request the router to open a port to forward its own port User doesn t need to log in the router to set the port forwarding Before using UPNP function please make sure the router s UPNP function has been triggered Because there are so many different routers and not all of them can support UPNP Please test if the router work well with the equipment if not we would suggest you don t enable this function PaA WAN IP Test Click the Show button it will show you another new page displaying the WAN IP address when it is connected to the Internet 7 3 Alarm Setting Page 7 3 1 External Alarm Input External Alarm External Alarm Mode Open Close Figure 21 Figure 2 below has listed the external alarm input setting If the alarm input pins have connected with an alarm detector Figure 4 please tick the External Alarm and then you will have enabled external alarm function If the external alarm detector is open mode please tick Open vice versa 7 3 2 Motion Detection Setting If user wants to monitor a certain area s movement please select the motion detection to trigger alarm The motion detection setting page is showed in Figure 22 This equipment supports four areas settings By ticking the options on the screen it will show you the area frame and the areas are numbered Using the mouse to dr2. or people or animal to enter the area the detector will switch on or switch off And it will send the external alarm signal into the IP camera Refer to the schematic Diagram of Figure 3 H Series IP Camera User Manual Mini High Speed Dome Switch PIR Power Figure 3 8 Alarm out Output Pins Switch Figure 4 Alarm Output Pin It is connected with a relay in the IP camera IP camera will control the switch to trigger the alarm bell or buzzer to alarm The relay is able to control the switch of an alarm whose voltage is no more than 36V and current is lower than 2A Please refer to the Figure 4 for the connection of an external alarm 9 Analog signal output Socket Supply BNC Female can output AV signal to connect analog signal device Instruction about SD Card socket SD Card socket is in the IP Camera if you want to install SD Card you must open the camera H Series IP Camera User Manual Mini High Speed Dome ADSL Modem 4 Network Connecting I l LANIP 192 168 0 1 WAN IP 202 96 82 177 A Router 2 G o I i k Switch Internet a m m a a w w Em a ff ff a N m N wam a N f N a f a m a a m m ao w rf a s i y F IP Camera 1 PCA 192 168 1 139 192 168 0 175 soi ARNESA lt x PC 3 Home Visit internet from anywhere Office Figure 5 4 1 Connection Instruction Before visit the IP Camera you should fir
3. 2 started Jul 2 19 06 54 vws 431 CHNOSD time Dynamic osd thread O of cam 1iregion 0 star Jul 2 19 06 54 ws 356D MP Start mp mag certer thread 10251 nk T11 7 102 0A GG sreflad ol thrrndt 25h Fodder startina an nart 1074 Figure 36 7 5 5 User browsing Log Checking Thu Jul 2 19 26 40 2009 192 165 0 101 GET param cgi cmd getmdalarm arn Thu Jul 2 19 26 40 2009 192 1668 0 101 GET param cgqi cmd getmdalarm an Tku Jul 2 19 26 40 2009 192 165 0 101 GET param cgl cmd gqetmdalarm an Thu Jul 2 19 26 40 2009 192 168 0 101 GET param cgi crmd getmdalarm an Thu Jul 2 19 26 40 2009 192 1668 0 101 GET param cgqi crmd getmdalarm an Tku Jul 2 19 26 40 2009 192 1658 0 101 GET param cgl cmd gqetmdalarm an Thu Jul 2 19 26 40 2009 192 165 0 101 GET param cgi cmd gqetmdalarm an Thu Jul 2 19 26 40 2009 192 168 0 101 GET param cgi cmd getmdalarm an Thu Jul z 19 26 40 2009 192 165 0 101 GET param cgl cmd getrelayattr Thu Jul 2 19 27 23 2009 192 168 0 101 GET getschedule cgi emngetgy act Thu Jul 2 19 27 47 2009 192 165 0 101 GET param cgi cmd getuser Thu Jul z 19 26 06 2009 192 165 0 101 GET getsnaptimer cgi timerctg ac Thu Jul 2 19 26 25 2009 192 168 0 101 GET param cgqi crmd getsmtp Thu Jul 2 19 26 45 2009 192 165 0 101 GET gettitp cqi ftp e act liste Figure 37 8 Advanced Application 8 1 Mobile pho
4. 3 is an example Administrator s Main Menu Virtual Server ID Service Ports server IP Enable 192 168 0 159 m 192 168 0 192 168 0 192 168 0 il C 192 168 0 L E C m Co 192 168 0 192 168 0 105 Ago nl Figure 13 x os TH LA B6 Ia EF Select status option and remember the WAN IP address enter the IP address in browser of PC 1 if IP Camra 1 can be visited via PC 1 the port forwarding is success And PC 2 and PC 3 can also visit the IP Camera 1 WAN IP address is allotted by ISP please make sure it s an available WAN IP address As WAN IP address is lack many WAN IP address are available in limited area If PC 2 and PC 3 are not in this area the IP Camera 1 won t be visited by them If user wants to put several IP Cameras into WAN every device should set the port forwarding In order to distinguish these devices every device should set a different port If the port of the device is not 80 should add the port to IP address with colon to visit the IP Camera Example http 202 96 82 177 81 6 2 DDNS In Figure 5 Router 1 get WAN IP address via ADSL these WAN IP address is always changing so the IP address can t be confirmed when visit the device in WAN We need the dynamic domain name server DDNS IP Camera 1 send IP configuration to DDNS every few time DDNS can recognize the WAN IP address of the router 1 which connected with IP Camera 1 The WAN IP address can be
5. 8 2000 XP Vista etc Browser Internet Explorer6 0 and Above or Compatible Browser Safari Firefox etc Application Software IPCMonitor exe 30
6. For more information pls refer the lt lt IPCMonitor User Manual gt gt in CD 28 H Series IP Camera User Manual Mini High Speed Dome J IP Camera Centralization Monitor 1 0 0 2 TP Camera System r setting History About Devices management veg x 0 0 List opt All Multi screen settings ee muu muu mum na AJ A e z d Device Manage Qp Device control D eu Local IF 127 0 0 1 Login date 2010 03 29 21 08 50 Figure 40 9 Specification cc i Image Capture Sensor Lens Zoom Minimum illumination TV System PTZ Horizontal rotate speed 250 s Vertical rotate speed 90 s Horizontal view angle Vertical view angle 8 Preset 128pcs IPCMonitor supports 8pcs of preset High Speed Dome Core Module Video codec Network transfer and control etc H 264 First Stream Resolution D1 CIF QCIF Basic Protocol TCP IP UDP IP HTTP SMTP FTP DHCP DDNS UPNP NTP Video control Mobile Phone View 29 H Series IP Camera User Manual Mini High Speed Dome Triggered Actions Email FTP SD storage external alarm send message to alarm server Date Time Setting Hardware Interface Ethernet Memory Alarm In Alarm Out Audio In Audio Out audio output interface x 1 RESET Button Power Input Socket Physical Index Power Operating temperature Humidit Power consumption Dimension Weight Software PC Side OS Supported Microsoft Windows 9
7. G stream For more details please refer to Chapter 8 5 Parenthesis Options Through the setting user can add the time and Camera name to the image 7 1 2 Audio Setting mode Audio Capture Open Close Audio Type G 11 Audio Capture Open Close Audio Type G46 w Figure 17 When choose audio input model to MIC will use build in or external MIC to gather the sound signal if choose line in will get signal from external audio gathering system like sound pick up Audio capture function can open or close and audio type can be G 711 or G 726 two types G 711 bit rate is higher but clearly G 726 compression rate is higher Only choose open audio capture and play the audio like Figure 10 then can hear the sound If choose close can save bandwidth and storage space 7 1 3 Image Setting Brightness Saturation Contrast Hue Figure 18 Drag the glide bar showed as above Figure 18 user can adjust the brightness saturation contrast hue 16 7 2 7 2 1 1 2 7 2 2 H Series IP Camera User Manual Mini High Speed Dome Network Setting Page Basic Network Setting IP Configuration Type IP Addr 192 166 0237 subnet Mask w BPE e anual ONS w Primary ONS 202 968 134 135 Secondary ONS wati HTTP Port 10537 B or 1024 49151 Figure 19 LAN Setting The default setting of this equipment is showed as above Figure 19 user can change it according t
8. H Series MiINi High Speed Dome IP Camera May 2011 V1 1 0 1 2 User Manual H Series IP Camera User Manual Mini High Speed Dome Index LINTRODUL IN icc ce cae i i ii ic i i ci iii 3 2 FUNC TION AND FEATURES iva tii aiaiai aiiai 3 A APPFPEARANLE AND TN DEA i as icissteicssstsstaianieeiasenaniiamanmebaaananiaiadsbeaainiionisamebiianateaniniaiannnenn 4 amp NETWORK CONNEE TIN u tistcreceas sitnictascncnnusaaicnciasniindulacieadiasmmanaitlsdeamuainiindusgeienaidinabinmnanamuniintion 7 DY PUTA CAMERA FROM LAN ccrich iai 8 D VISTE TP CA VIERA FROM WAN Nuuu as niiae 12 TOTHER SELING ecaa 15 1 H Series IP Camera User Manual Mini High Speed Dome Introduction The IP Camera combines a high quality digital video camera with network connectivity and a powerful web server to bring clear video to your desktop from anywhere on your local network or over the Internet Your IP Camera package should contain the following items If any of the listed items are missing please contact your reseller from where you purchased the camera for assistance The package includes V y x v V v ZV N lt SORS N IP Camera 1 IP Camera Utility CD 1 12V Power Adapter 1 Cable 1 Bracket 1 Screw 1 set Network Connector 1 Function and Features 32 bits RISC processor and special video encoder which can be up to 3M pixels encoding performance Support H 264 Main Profile Level3 0 compression format bit
9. P Camera 1 by PC 2 you should firstly do the setting as 1 to make sure that you can visit IP Camera 1 through PC 1 and then do the setting of router 1 do the port forwarding from the router The PC 2 s visit application could be sent through router 1 to IP Camera 1 Normally PC 2 could only send the information to router 1 if you don t do the setting of router 1 then PC 2 could not visit IP Camera 1 H Series IP Camera User Manual Mini High Speed Dome 5 Visit IP Camera from LAN 5 1 Set IP Address The IP addresses of IP Camera and PC should be at the same segment in Figure 5 the IP Camera 1 can t be visited Run the HSearch_en exe in the CD click Search button and then select the IP Camera to reset the IP Camera s IP address as the Figure 6 i HSerial Intranet search and settings 0 1 2 Local PC information Device information Realtek RTL8139 810x Far s Device name 192 166 0175 255 255 255 0 IP config Set IP automatically IP addresstlh 192 168 139 192 168 0 1 Subnet mask LlY 255 255 255 Gateway E 192 1668 1 192 165 0 1 DMS1 D3 192 166 1 Device list DNS ZEM Mo DeviceMame MAC 1 O01 acdo 00 00 88 11 11 10 Http port P Authentication Account for watching Password for watching UpdatetFS 2 Tips q This tool is only used weithin LAN po and device is within the same subnet 2 gt Only the legit user can update device informa
10. ag the area frame you can change the position of the frame and to drag the right bottom corner of frame you can change the size of frame After setting is finished click Apply button then the motion detection is enabled 18 H Series IP Camera User Manual Mini High Speed Dome View Media Network Alarm Advanced System 2010 12 17 15 41 33 connectedfuser 2 Window Window Windows Sensitivity Sensitivity Sensitivity Sensitivity i u u E 35 3 3 gt Figure 22 7 3 3 Alarm Mode Setting NN Save Picture on the SD card W Save Video on the SD card im ave Yideo onthe FTP Server FIP Server Settine Bi Relay out Alarm Server Alarm Server Settine E mail Alarm Figure 23 When the alarm is triggered user can adopt several ways to alarm gt Snapshot a live picture of the site on the SD card gt Record a 30 seconds long video on the SD card including 5 seconds long video before the alarm was triggered gt Send the recorded video on the SD card to the FTP server Please enable save the video on SD card function and insert the SD card first gt Relay on refer to Figure 2 and Figure 3 enable external alarm function and set the time 19 H Series IP Camera User Manual Mini High Speed Dome gt Send alarm info to the alarm server gt Send alarm info to E mail 7 3 4 Alarm Time Setting Figure 24 IP Camera will trigger alarm only on the time s
11. configuration and make sure the communication between equipment and PTZ decoder goes well In the PTZ control area the user can control PTZ by click the arrow rotation direction up down left and right Clicking set can set one preset and clicking call can call this preset Ages and are used for zoom andi are used for automatic cruise and stop automatic cruise 5 3 Notice for the first time use Please change the following 2 settings when using for the first time 1 Please refer to the content of part 7 4 1 to change the initial passwords of admin user and guest Their initial passwords are respectively 123450 user guest 2 Refer to the content of part 7 5 2 to set the system time 6 Visit IP Camera from WAN 6 1 Port forwarding Follow the Visit IP Camera from LAN steps make sure PC 1 can visit IP Camera 1 In Figure 5 before the computers in WAN PC 2 PC 3 can visit the IP Camera 1 must put the IP Camera 1 into WAN You can set port forwarding on Router 1 to put IP Camera 1 into WAN Open the Router Setting interface on PC 1 The interfaces for different routers are different and the port forwarding settings are different please refer the router manual to set For most 12 H Series IP Camera User Manual Mini High Speed Dome routers Virtual server option can be found in setting interface Fill the IP address and port of IP Camera 1 into corresponding blank Figure 1
12. e provide a free DDNS url when IP Camera is connected to the internet this URL can be used to visit the device Manufacture provides free software support Multi view Long time recording video replay etc Support video view by other browsers like as Firefox safari etc Appearance and interface Appearance Figure 1 H Series IP Camera User Manual Mini High Speed Dome 3 2 Interface of Equipment ht fr 0 m g Figure 2 1 Power Input Socket Connect DC adaptor its output should be 12V power specification a RESET interface Press the RESET button and hold on more than 5 seconds the equipment will restart and recover to the factory default settings 3 2 RJ45 Ethernet interface RJ45 Ethernet socket is 10 100M self adjust The equipment can connect to all kinds of network equipments such as hub router switch etc 4 Audio Input interface Audio input socket is designed for connecting external microphone or line in audio signal Please refer to 7 1 2 and select right settings 5 Audio Output interface Audio output socket is for line out audio player such as headphone speaker etc 6 RS485 Interface Connect to the device with RS485 port to control PAN TILT etc Note this interface does not apply to high speed dome camera 7 Alarm in Alarming Input It collects external detector The detector should be switched type always on or always off If the detector has detected the smoke
13. es es ES ok Lpgrade fF Browse Lok Figure 35 gt Reboot button to restart the equipment if you have set the pre position and it will turn this position gt Click Factory Default button equipment will restart and back to all the default settings gt Click save it will save all the present settings 25 H Series IP Camera User Manual Mini High Speed Dome gt Restore part select the setting file you have saved click OK it will recover all the settings gt Upgrade part select the firmware file for upgrading click OK and you are able to upgrade the equipment After the upgrading equipment will restart Upgrading took a little long please wait patiently If upgrading is finished it will show you a message to remind you 7 5 4 System Log Checking Thu Jan 1 00 00 04 UTC 1970 BOOTTAB System Start Jul 2 19 06 44 syslogd started BusyBox w1 1 Jul 2 19 06 49 sddetect 323 A new SD card insert start check Thu Jul 2 19 06 49 STD 2009 Wa AUTO vs server start Jul 2 19 06 51 sddetect 323 Check sd card finisked Result is D Jul 2 19 08 51 sddetect 323 Mount SD card on bin vws sd Jul 2 19 06 54 vs 3680 SNAP tcreat snap mag recy thread 5126 sucess Jul 2 19 06 54 vs s6e0 EXT creat ext alarm meq recy thread 6151 sucess Jul 2 19 06 54 vs 429 ENC getstream thread of channel 11 Started Jul 2 19 08 54 vs 430 ENC getstream thread of channel 1
14. et by Figure 24 Please adjust the system time first Refer to Part 7 5 2 7 4 Advance Setting 7 4 1 User Management admin USEF guest Figure 25 There have three level of authority they are admin user guest Admin have the highest authority it can do any change to the settings User account only can operate the IP camera can t do changes to the settings and please refers to Figure 26 Guest account only can watch the video can t do any operation to the IP camera and please refers to Figure 27 20 H Series IP Camera User Manual Mini High Speed Dome 2010 12 21 14 51 10 was FirstStream b First Stream w Figure 27 21 H Series IP Camera User Manual Mini High Speed Dome 7 4 2 Auto Capture Setting snap interval 60 minutes BN Save Picture onthe SD Card Figure 28 Please tick save picture on the SD card the equipment will snapshot every short time for example showed as Figure 28 every 60 minutes 7 4 3 E mail Setting SMTP server name server port 25 ssl i Authentication Oo of Username test recevent 163 com e Mail Address 1 e Mail Address 2 e Mail Address 3 Sender testi sohu cam Return e Mail address subject Message the max length is 255 Figure 29 In Figure 29 the blanks which have been filled with info should be filled If any info is not filled right the setting will fail Before setting these parameters please refer the set
15. ing Transport dialog box Please select HTTP for transport protocol and 80 as port ID and then click ok Please be back to Transport Setup to change Custom to Auto Finally click ok at the bottom Please refer to the above Figure 39 Then you could view the video through Firefox or Safari now 27 H Series IP Camera User Manual Mini High Speed Dome QuickTime Preferences gt lt Register Audio Browser Update Streaming File Types Advanced Streaming Transport Setup F RTSP Proxy Server x Transport Protocol Ima x a Streaming Transport Enable DirectDraw on secondary monitors Enable Direct3D video acceleration Media Encoding Enable encoding using legacy codecs Tra Icon _ Install QuickTime icon in system tray Media Keys Figure 39 2 The settings to use Safari in MAC OS When use MAC because QuickTime is the default software user only need go to Utilties folder under the Applications folder and start command line program Terminal program input the command as qtdefaults write TransportSettings HTTP 80 Then open safari to view If can t view from safari please try http ip port mobile html 8 3 Centre Management Software IPCMonitor is a free software offered by factory several devices on LAN and WAN can be browsed at the same time The software also support snap video record and so on The below Figure 40 is the interface
16. ne Browsing After connect into network you can view by mobile phone Device will send MJEPG picture to mobile phone you can setting the image resolution which mention on Chapter 7 1 1 View way as below 1_ _ http IP Port mobile html for example http 58 61 54 177 1025 mobile html http test 3322 org 1025 mobile html smartphone like iphone windows mobile symbian black berry Android etc can use this mode to visit If can t visit you have to download and use opera mobile browser 26 H Series IP Camera User Manual Mini High Speed Dome 2 http IP Port for example http 58 61 54 177 1025 http test 8322 0rg 1025 Only iphone can use this mode to visit 8 2 Other web browser visit device Using browser with IE kernel user must download the Activex Using other web browser like Safari or Firefox it will use Qicktime to play Safari for example you can find the player interface as the below Figure 38 View Media Network Alarm Advanced System 009 12 02 11 39 33 Figure 38 1 The settings to use Firefox or Safari in Windows OS In the Windows OS if you don t install the QuickTime it will remind the users of installation Users could install the Quicktime according to its message After installation users can start the Quicktime program and to access the Quicktime Preferences dialog box from Edit Menu Click Advanced select custom in the Transport Setup It pops up the Stream
17. o your network environment HTTP Port The IP address Identity one IP camera in the network you can run several programs on this equipment and every program will transfer the data through some port in fact data is transferred from one port to another The port setting of this page is asking user choose which port to transfer the data for the web server WIFI Setting Enable ywireless Enable Disable SSID hod Infrastructure Security mode WPA Algorithri ker Re type key Check Wireless Setup Figure 20 The wireless setting page is showed as below Figure 20 user can click the Search button and it will show you the page telling you the WIFI network it has detected Please choose 17 H Series IP Camera User Manual Mini High Speed Dome one of it and the network data will filled in the blanks automatically For example SSID encryption algorithm etc User only needs to fill in the password and retype the password After you configured it you can click the Check button to check if there is any mistake Check is success please click Apply button to set it If you have set wifi please unplug the network cable and power on the ip camera again for rebooting it then the wifi will work 7 2 3 Remote Access Setting l Manufacturer s DDNS and Third Part Dynamic DNS Please refer to the content of the part 6 2 2 UPNP UPNP stands for universal plug and play if you started UPNP
18. rate is smaller and the image is more clear It is more convenient for transferring through Internet and save more storage space D1 CIF QCIF resolution optional User can change some specification according to their demands to satisfy his own visual prefer Support PAL NTSC CCD Support 10x optical zoom Pan 360 Tile 90 support 3 different kinds of P T rotate speed Support 3 kinds of video stream suitable for Local Internet and Cross platform view lt s 3 1 H Series IP Camera User Manual Mini High Speed Dome Support to connect external audio capturing device like MIC phone or sound pick up to capture the audio External speaker can play the voice sent to the live scene to achieve two way intercom function Audio support G 711 and G 726 types Support waterproof class of IP66 Built in web server Support video view and parameter settings by browser use one port to send all the data it facilitates network setting Support mobile phone watching Support UPNP port forwarding automatically on the router Support maxim 32G SD card for video and picture storage Motion detection and alarm pin can be connected to external sensors to detect environmental situation Alarming record can be stored by email SD card and FTP server External alarm can be open when detecting unusuality It also sends alarm info to the alarm server Support three level of user authority Support upgrading online Manufactur
19. rt is not 80 the port number should be add to the domain name with colon Example http ijpcam 3322 org 81 14 H Series IP Camera User Manual Mini High Speed Dome 7 Other Settings 7 1 Video Setting Page 7 1 1 Video Setting Video Standard Resalution Hit rate 2040 kbps Maximum frame rate 25 Bigs Fesolution CIF Bit rate 256 ERNE Maximum frame rate 10 v ROS Mobile resolution Time Stamp on of Camera name on O of Mame P Camera Figure 16 1 Video standard identification It will identify the video standard of CCD and display it 2 First Stream Use H 264 code support D1 CIF QCIF higher resolution high quality picture but bit rate will be higher and will take more bandwidth User can specify stream normally high bit rate higher image quality But the frame rate need to setting according to the bandwidth when bandwidth is narrow if set high frame rate the result will be worse User can set Max frame rate when the bandwidth is limited suggest set to lower frame rate Normally above 15fps the stream is smoothly 3 Second Stream Use H 264 code support CIF QCIF also can setting bit rate and Max frame rate 4 JPEG Stream JPEG stream send JPEG picture support the browser which don t support H 264 code like 15 H Series IP Camera User Manual Mini High Speed Dome mobile phone Also can use Http ip port mobile htm l to view JPE
20. searched on DDNS by domain name Herein domain name substitute the dynamic IP address If the device can t be visited by IP address this domain name is also unavailable 6 2 1 Manufacturer s Domain Name Device manufacturer has established a DDNS and allotted a dynamic domain name to every device the domain name has been integrated into devices when producing For example enter domain name of Figure 14 the browser will connect the device and display the IP address 13 H Series IP Camera User Manual Mini High Speed Dome O on off SubDornain DD2aabg rwsvr COM Figure 14 The domain name is realized by forward manner the domain name will change into the IP address and port number of the device when visit by domain name If the device can be visited by IP address but can t be visited by manufacturer s domain name please check the DNS info is available or not and make sure the DNS setting is the same with the DNS setting of PC in LAN 6 2 2 Third Part Domain Name User can also use third part DDNS such as www 3322 org User should apply a free domain name from this website and fill the info into the below blanks Figure 15 and save the settings Then the domain name can be used O on of Provider Username password eesecesess Your Domain Figure 15 The third party domain name is realized by analysis manner the domain name will be displayed in the browser all the time when visit camera If the po
21. ss Subnet mask Primary DNS secondary DNS Sp status Browser SD Card Figure 33 Device ID is set by factory Every ID is unique Network Connection status will display LAN when connected by wired cable and display Wireless LAN connected by wireless Router SD status will remind if SD card inserted and display the free capacity Click Browse to view the contents in SD card and Format SD Card as fat32 to format SD Card and Unplug SD Card to stop the work of SD Card The device supports max 32G SD card Please format the SD card to FAT32 before use the card on Camera Please check if the SD Card matches the camera or not before purchase the SD Card 24 H Series IP Camera User Manual Mini High Speed Dome 7 5 2 Date and Time Setting 2010 12 21 14 54 56 ShIT 05 00 Beijing Chongging Hong Kong Urumai Wanual setting BECHE 2010 12 21 Cine 14 54 55 HAMM ss Sync with computer time AUER 2010 12 21 14 48 46 Network Time Protocol MTP Server Interval 0 2 x burs Keep current setting Figure 34 Please refer to above Figure 34 Select the time zone first There are three options to set the time and date One is manually another is keeping the same as the time and date on the computer and the third one is getting it from the NTP server 7 5 3 Default Setting Reboot reboot Factory default factory default Backup setting data Save Restore
22. stly connect it to the Network supply the power to it and check if the light of RJ45 Socket is normal to make sure all of the communication links are fluency The connection method likes as Figure 5 1 IP Camera 1 and IP Camera 2 are connected separately to 2 different LANs 2 And these 2 LANs are already connected to the Internet In order to get the LANs to be connected to the Internet they are required to be equipped with router and to apply for the communication link from the local Internet Service Provider ISP and connect to it by ADSL or optical fiber etc 3 PC 3 is connected to the Internet 4 2 Visit Instruction To visit the IP Camera you should do some settings of IP Camera and Internet besides getting the communication link fluency 1 The PC and IP Camera are in the same LAN If you want to use this PC to visit the IP Camera you need to make sure their IP address is at the same segment Otherwise you need to do the reset of the IP Camera s IP address For example the IP Camera 1 s IP address in Figure 5 is 192 168 1 139 at the segment of 192 168 1 while the PC 1 s IP address is 192 168 0 175 at the segment of 192 168 0 then you will be not able to visit the IP Camera through the PC 1 You need to change the IP Camera 1 s IP address to 192 168 0 139 firstly 2 The PC and IP Camera are in different LANs but they are all connected to Internet For the IP Camera 1 and PC 2 in Figure 5 if you want to visit I
23. sword is 123456 Click Update The setting will take effect now Select the device in list box click Browse button it will open the Browser automatically and pop up a window at the same time which requires to inputting the user name and password Then you see the home page of the IP Camera 1 just as below Figure 7 Video View Mobile view Setup Figure 5 2 Visit IP Camera If you use internet explorer or compatible browser to visit it for the first time use other browsers please refer to 8 2 you will be required to install the ActiveX before viewing the video As Figure 7 click Download ActiveX when first use The dialog just as Figure 8 will pop up accordingly Click Run then it will download and install the ActiveX automatically File Download Security Warning Do you want to run or save this file Name SEClientOck Setup exe Type Application 1 53 MB From 192 168 0 158 Aur Cave Cancel while files from the Internet can be useful this file type can potentially harm your computer l you do not trust the source do not run Dr save this software what s the risk H Series IP Camera User Manual Mini High Speed Dome Figure 8 After the ActiveX installation click the Video View as Figure 7 then you will enter the video view home page as below Figure 9 View Media Network Alarm Advanced System 010 Y a 14 36 45 FirstStream w Figure 9 5 2 1 Menu col
24. tings of Outlook Express 22 H Series IP Camera User Manual Mini High Speed Dome 7 4 4 FTP Setting See ee 1392 1660 20 Passive mode on off Figure 30 In order to use FTP function user should apply username and password on the FTP server first And please apply some storage and the authority to write and create sub category into it 7 4 5 Alarm Server Setting Server Address 132 166 0 200 Server Port 30002 Username test Figure 31 Please confirm if you have connected to alarm server The alarm message format as follow GET api alarm asp username username amp userpwd password amp rea alarm type 1 Motion Detection 2 Alarm from Alarm in port 3 Other Type amp lo 0 Alarm server need develop by customer user can extend other functions on this server like SMS MMS alarm and mobile phone etc 7 4 6 PTZ Setting Before buying the PTZ please check this device supporting which PTZ protocol you can check from Figure 32 Read the manual of PTZ and set PTZ address baud rate data bit stop bit check type in Figure 32 23 H Series IP Camera User Manual Mini High Speed Dome PTZ Protocal Address Protocal PELCO P Com Setting Haudrate Data bit Stop bit Check type Figure 32 7 5 System Setting Page 7 5 1 Device Information Checking gt gt Device information Network connection Software Version Mac address 00 00 14 21 11 05 IP addre
25. tions gt Search Fs Browse F4 Figure 6 If you have the firewall software in your PC when you run the HSearch_en exe it may pop up a window to say if you want to block this program or not then you should choose not to block IP Camera by default use fixed IP address 192 168 0 158 and fixed http port 80 If you don t have this software you could also press down the reset button Figure 2 to go back the factory setting Then you could use this defaulted IP address to visit the IP Camera Setting Instruction v Please carefully check the Local PC information on the top left corner which lists the PC configuration If there are several network adapters in the PC please select the one H Series IP Camera User Manual Mini High Speed Dome you are using and make sure the IP address of IP Camera is as the same segment of the PC v Change the content of IP config on the right to make sure the content is the same as Local PC information Only the last section of the IP address which needs setting by yourself you can set it as 139 just like Figure 6 v Ifyou don t know how to fill out the content of IP config you could also tick the Set IP automatically to get the IP address from the router automatically If can t get IP from router the IP Camera will set it to 192 168 0 158 for itself v Put the user name and password into Authentication By default the user name is admin pas
26. umn There are 2 kinds of menu one is main menu the other is submenu The main menu lies at the top of the interface including View Media Network Alarm Advanced and System Submenu lies on the left of the interface and different main menu is in line with different submenu 5 2 2 Video Displaying Area The video displaying area is correspond to the resolution the higher the resolution is larger the displaying area will be If motion detection was set when it has detected any movements of the certain area it will show a pane to call user s attention Figure 10 is status column at the bottom of video displaying area 1 2 0 Figure 10 1 Displaying how many users are visiting this video 2 If user has clicked the Record button in the Figure 9 here will show Rec means the video is being recorded If click the Record button again it will stop recording 3 File Saving Path Setting User can click it to browse a file saving path to save the 10 H Series IP Camera User Manual Mini High Speed Dome recorded video and snapshots 4 Talk back Button Click it and the stereo equipment which was connected to the IP Camera will play the achieved audio Click it again the speaker will stop playing 5 Audio Play Button Click it to play the audio getting from IP Camera click it again IL will disable this function 5 2 3 Browse SD Card When SD Card inserted click the submenu the pop
27. up page will display the content in SD Card like the Figure 11 Index of sd Size KByte lat Name Parent Folder 19991212 2UUYU Fue Figure 11 In above figure text in is catalog info click sub catalog to browse the recorded images and videos The images will be displayed when you click them and the videos will be downloaded and played by the video player in user s computer automatically when click the video 5 2 4 Capture Click the Capture button which could take photos for the current video and store the image at the present path 5 2 5 Record Click Record button which could record the video with audio and store it at the present path When recording there will be an indicated symbol in the status of video display area to show you it is recording Click the Record button again and then the record stops 5 2 6 Playback Click Playback button it will pop up a player which could play the video stored on your PC disk 11 H Series IP Camera User Manual Mini High Speed Dome Figure 12 W these buttons are for play stop the previous recorder the next recorder open the recorder file Please click the button of open the recorder file first and select the file you want to play you can playback the recorder 5 2 7 The control of Pan Tilt For the control of PTZ 485 interface of the equipment must be connected with the PTZ decoder Please refer to the7 4 6 part for
Download Pdf Manuals
Related Search