L24BF Care & Use
Contents
1. 1 Keep pressed for more than 3 s the UP DOWN keys 2 The POF message will be displayed and the keyboard will be locked At this point it will be possible only to see the set point or the MAX o Min temperature stored 3 lfakeyts pressed more than 3s the POF message will be displayed 6 7 TO UNLOCK THE KEYBOARD Keep pressed together for more than 3s the a and keys till the Pon message will be displayed 6 9 THE ON OFF FUNCTION With onF oFF pushing the ON OFF key the instrument is switched off The 1 OFF message is displayed In this configuration the regulation is disabled i To switch the instrument on push again the ON OFF key IMPORTANT NOTE The controller has been programmed to only allow a temperature adjustment within a specified range of 33 F to 43 F 15 PROFESSIONAL GRILLS TOE PLATE INSTALLATION When the unit is secured in place install the louvered toe plate Secure louvered toe plate by snapping the latch into the latch catch on the unit Refer to Figure 3 TOE PLATE INSTALLATION ILLUSTRATION Figure 3 TOE PLATE INSTALLATION CAUTION The louvered toe plate must be removable for servicing The floor cannot interfere with removal The louvered sections of the toe plate must not be covered or obstructed so as to prevent proper air circulation PROFESSIONAL GRILLS SHELVING IMPORTANT NOTE Interior louver openings and fan guard openings should n2. 4 Carefully move unit to installation site and place in front of opening WARNING A minimum of two people should lift the unit of the base to prevent possible personal injury PROFESSIONAL GRILLS The refrigerated compartment is warmer than usual Is your control set properly Is the light staying on Is your condenser area clean and free of obstructions Has the door been open for a long time or more frequent door openings occurred Are the internal louvers and fan guard openings obstructed Has warm product just been placed in the cabinet The refrigerated compartment is colder than usual e Is your control set properly e Is your door closing and sealing properly e Is the ambient temperature within the normal operating range The refrigeration system runs for long periods of time e Is the condenser area clean and free of obstructions e Have the doors been open for a long time or more frequent door openings occurred e Have warm product just been placed in the cabinet e On hot days and in warm room temperatures the system will run long Condensation forms inside the refrigerated compartments e This is normal during high humidity and frequent door openings e Are the doors closing and sealing properly Condensation forms on the outside of the unit e During periods of high humidity some condensation might appear on outside surfaces The condensation will disappear when the humidity drops Meanwhile be sure doors are
3. wnn O E ig User Manual Installation Instructions DN nd y A Lynx Professional Grills ml LY NX 5895 Rickenbacker Rd Commerce CA 90040 Service 888 289 5969 PROFESSIONAL GRILLS Tel 323 838 1770 Fax 323 838 1778 WWW Lynxgrills com 5895 Rickenbacker Road e Commerce CA 90040 e 888 289 5969 e Fax 323 838 1778 e www lynxgrills com 23 INTRODUCTION Congratulations on your purchase of a Lynx residential refrigeration product Lynx has taken its expertise and experience into creating the highest quality and most innovative residential products on the market Lynx s product offering gives you the opportunity to enjoy the functionality and user friendliness outdoors or in just about any room of your home All Lynx products are built with commercial grade Stainless steel providing you with the beauty and durability for a lifetime of use This Installation and Operation Manual will answer your questions about the features operation and maintenance of your Refrigerated Cabinet model If you have questions that are not addressed here call Customer Service at 888 289 5969 IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit First as you follow these Installation and Operation instructions take particular note of the DANGER CAUTION and WARNING symbols when they appear This information is important for the safe and effic
4. Hole Plugs from the Top and Bottom Hinge Bracket mounting holes Then place them in the holes on the opposite side made vacant 5 Using the screws from Step 3 install the in Step 3 new Top and Bottom Cabinet Hinge Brackets 6 Remove the Top and Bottom Door Hinge Brackets and Push Punger Bracket and save the screws for later 10 PROFESSIONAL GRILLS PROFESSIONAL GRILLS T L 4 Step 5 Using the screws from Step 3 install the new Top and Bottom Cabinet Hinge Brackets Siep 6 Remove the Top and Bottom Door Hinge Brackets and the Push Plunger Bracket Save the screws for later 7 Remove the Lynx name plate from the Door using a Plastic Putty Knife Install the new Lynx nameplate included 8 Insert bearing into Top Door Hnge Bracket 9 Insert V Block into Bottom Door Hinge Bracket attach with E Clip 10 Attach the Top and Bottom Door Hinge and Push Plunger using screw removed in Step 6 11 Place Lower V Block into Lower Cabinet Hinge with notch parallel to cabinet 12 Lift the Door Assembly and insert top pin into bearing Then move door toward cabinet and align V Blocks 13 Insert and tighten the Lower Hinge Pin to complete assembly Step 8 Insert bearing into Top Door Hinge Bracket Step 9 Insert V block into Bottom Door Hinge Bracket see NOTE below and EX attach with E Clip NOTE 6 D ORIENTATION Bottom View Step 10 Attach the Top and B
5. PROFESSIONAL GRILLS PROFESSIONAL GRILLS INSTALLATION IMPORTANT NOTE If installing on a concrete floor concrete fasteners are required and not included with the anti tip kit CAUTION Any finished flooring should be protected with appropriate material to avoid damage from moving the unit If unit has been laid on its back or sides place unit upright and allow minimum of 24 hours before connecting power 1 Plug the unit into the 15 amp grounded GFI outlet located in the installation opening With power applied to the unit check that the lighting and cooling function operate properly then turn off power to the wall outlet at the circuit breaker WARNING Shut off power to the wall outlet before installing into the opening 2 Check that the following are level and square e Front face and interior opening e Installation opening and floor surface e Countertop bottom front edge IMPORTANT NOTE Leveling legs should not be extend more than 3 from bottom of the cabinet IMPORTANT NOTE The floor under the unit must be at the same level as the surrounding finished floor 3 If all surfaces are level a Measure from the floor to the bottom of the front edge of the countertop b Measure the rear of the unit cabinet from the floor to top of cabinet at back corners c Adjust legs so B measurement is less than A measurement Using an adjustable wrench or pliers turn legs counterclockwise to raise the unit or c
6. airflow can cause unit to malfunction and may void the warranty PROFESSIONAL GRILLS CAUTION Use only genuine Lynx replacement parts Imitation parts can damage the unit and may void the warranty INSTALLATION INSTRUCTIONS General e All electrical instructions assume that outlet is located 4 to 10 inches from the floor e Floor must be level in area of installation Leg levelers are used for fine tune adjustment only and should not be used to compensate for floor differences exceeding inch e When moving unit into position take care to protect floor surface with cardboard rugs etc e Never attempt to move unit without the aid of at least one other person e Always secure door shut prior to moving the unit Finished Opening Requirements e Height 34 3 8 minimum 35 1 2 maximum e Depth 26 1 2 e Width 24 1 4 20 PROFESSIONAL GRILLS WARRANTY One Year Parts and Labor Warranty For one year from the date of original purchase within the United States and Canada when used and maintained according to instructions Lynx Grills warranty covers all parts and labor to repair or replace any part of the product which proves to be defective in material and workmanship Four Year Additional Compressor Warranty Lynx will warrant to the original user the sealed in mechanism consisting of the motor compressor and component parts within the sealed housing of the condensing unit for an additional per
7. closing and sealing properly If condensation persists contact your Lynx Factory Authorized Service Center You need product information e Contact Lynx Grills Inquire via the WEB at www Lynxgrills com Call 888 289 5969 for factory assistance for information installation or product information Write to Lynx Corporation Customer Service Department 5895 Rickebacker Rd Commerce CA 90040 e or e mail us at info lynxgrills com You need product service e Check the model and serial number of your unit located on the label attached to the inside top of the cabinet For the location of the Service Center in your area contact your dealer inquire via the WEB at www Lynxgrills com or write to Lynx Professional Grills Customer Service Department 5695 Rickenbacker Road Commerce CA 90040 call 888 289 5969 or e mail us at www Lynxgrills com You need replacement parts or accessories e Use only genuine Lynx replacement parts and accessories Genuine Lynx parts and accessories are designed to work correctly with Lynx products and offer superior service life The use of non Lynx parts can damage the unit and may void the warranty e Check the model and serial number of your unit located on the label attached to the inside top of the cabinet For the location of the Service Center in your area contact your dealer inquire via the WEB at www Lynxgrills com or write to Lynx Professional Grills Customer Service Department 5695 Rickenbacker R
8. ee eet ea TEMPERATURE CONTROLLER ADU NIENT a eee aet y ZTS Discos SART ESTA PRODUCT TEMP RANES TTT CHECKING PRODUC T TEMPERATURE TT MAINTENANOE esrrregrine i na A EE E Ea CEE ANIN O cool id oro LIGAT BOLB RERCACEMEN E steps iria asisto aos CONDENSER CCEANIN G respecto osa TROUBLE AOON Soros en ee eee ee ere ae UUE 475 a dT CO CON OA A Qn EM GQ KM AA A gt A A A A A A A A A A A A A A ON OO O DD GQ GQ GQ KM NY NY CO o O PROFESSIONAL GRILLS GENERAL PRECAUTIONS DANGER Risk of child entrapment before you throw away your old refrigerator or freezer take off the doors and leave shelves in place so that children may not easily climb inside DANGER Altering cutting of the power cord or removal of the power cord removal of power plug or direct wiring can cause serious injury fire and or loss of property and or life and will void the warranty WARNING e Never attempt to repair or perform maintenance on the unit until the electricity has been disconnected e The anti tip kit must be installed on this unit before it is used Never use the drawers shelves or doors as steps or to support more than they were designed to support CAUTION e Do not lift unit by door or door handles e Failure to clean the condenser every three months can cause the unit to malfunction This could void the warranty e Never install the unit behind closed doors Be sure front louvered toe plate is free of obstruction Obstructing free
9. receptacle DANGER ELECTROCUTION HAZARD Electrical grounding required This appliance is equipped with a three prong grounding polarized plug for your protection against possible shock hazards e Never remove the round grounding prong from the plug e Never use a two prong grounding adapter e Never use extension cord to connect power to the unit Where a two prong wall receptacle is encountered or a longer power cord is required contact a qualified electrician to have it replaced in accordance with applicable electrical codes DANGER Failure to comply with the above electrical guidelines may result in possible injury death fire or loss of property UNPACKING AND MOVING CAUTION Do not cut cardboard sleeve covering the unit Cutting may result in damage to the exterior of the cabinet 1 Uncrate the unit outside on a flat level surface Remove the cardboard sleeve by removing the banding holding the sleeve to the shipping base Carefully lift the cardboard sleeve up over the top of the unit 2 Carefully lift unit off base and onto a hand truck or dolly this should be done with a minimum of two people larger units may require additional helpers Make sure unit is balanced on transporting device Secure unit to transporting device using soft flexible strapping Protect unit surfaces with cloth material where strapping contacts unit 3 Before moving unit secure door to unit with tape to the door closed
10. will be displayed followed by the maximum temperature recorded 3 By pressing the a key again or by waiting 5s the normal display will be restored HOW TO RESET THE MAX AND MIN TEMPERATURE RECORDED 1 Hold press the SET key for more than 3s while the max or min temperature is displayed rst message will be displayed 2 To confirm the operation the rst message starts blinking and the normal temperature will be displayed 6 1 HOW TO SEE THE SETPOINT 1 Push and immediately release the SET key the display will show the Set point value s 2 Push and immediately release the SET key or wait for 5 seconds to display the probe value again 6 2 HOW TO CHANGE THE SETPOINT 1 Push the SET key for more than 2 seconds to change the Set point value 2 The value of the set point will be displayed and the C or F LED starts blinking 2 To change the Set value push the or arrows within 10s 4 To memorise the new set point value push the SET key again or wait 10s 6 3 HOW TO START A MANUAL DEFROST C Push the DEF key for more than seconds and a manual defrost will start 14 PROFESSIONAL GRILLS TEMPERATURE CONTROLLER SET To display target set point in programming mode it selects a parameter or confirm an operation E DEF To start a manual defrost A UP To see the max stored temperature in programming mode it browses the parameter codes or increases the displayed value DOW
11. 3 w Ld 26 7 8 24 22 1 16 1 Byes PROFESSIONAL GRILLS PREPARING THE SPACE Make sure that the opening where the unit is to be installed is properly prepared Refer to Figure 1 to ensure the space dimensions and electrical service are correct for the models to be installed CAUTION If unit is being installed under a counter top it is required that the counter top be supported by structure other than the refrigerated cabinet to prevent damage to the counter top IMPORTANT NOTE Allow 25 clearance in front of the unit for full door swing and shelf pull out IMPORTANT NOTE Make sure the floor under the unit is level with the surrounding finished floor Protect a finished floor with plywood cardboard or some other suitable material before moving the unit into place Failure to do this may result in damage to the floor PREPARING ELECTRICAL CONNECTIONS A 115 volt 60Hz 15 amp circuit with GFI protection and electrical supply are required A separate circuit is required for each Lynx unit installed Follow the National Electrical Code and local codes and ordinances when installing the receptacle All Lynx units come equipped with a NEMA 5 15P 90 plug with a minimum of 5 feet of cord extending beyond the rear of the cabinet The electrical outlet must be flush with or recessed into the back wall IMPORTANT NOTE Never use an extension cord to extend the power cord to the electrical
12. N To see the min stored temperature in programming mode it browses the parameter codes or decreases the displayed value 4 To switch the instrument off if onF oFF La Q Not enabled KEY COMBINATIONS ZA TL WZ To lock amp unlock the keyboard SET Y To enter in programming mode SET A To return to the room temperature display Each LED function is described in the following table ae JON Compressorenabled Anti short cycle delay enabled EM Ped 2222222 On mams S E N Continuous ele 1 ruming EY ON_ Energysavingenabled o EPE ON Measurementunit o Programming phase 13 PROFESSIONAL GRILLS DOOR LOCK See Figure 6 for door lock and latch bracket details r Nut Lock strike Step 2 Pull door to the side then lower door Figure 6 Door Lock Step 1 Support door in the open position as shown Remove Hinge Pin DOOR HINGE REVERSAL Procedure for switching direction of door swing using Left Hand Hinge Kit Part No 90197 1 Support the door and remove the hinge in Step 3 Remove 2 Pull the door to the side and lower the Esc la ble Hinge Brackets door from the upper hinge pin and and save the screws for later bracket 3 Remove the Top and Bottom Cabinet Hinge Brackets and save the screws for later 4 Remove the Hole Plugs from the Top and Bottom Hinge Bracket mounting holes and put them in the opposite sides made vacant in Step 3 Step 4 Remove the
13. allation in direct sun light or near a heat source LIGHT BULB REPLACEMENT To replace a defective or burnt out light bulb unscrew the bulb counterclockwise and replace with an identical 15 Watt bulb or smaller Contact Lynx for a replacement bulb MAINTENANCE CLEANING To clean stainless steel exterior or interior surfaces use a soft non abrasive stainless steel cleaner to wipe down the these surfaces To clean interior and exterior non metallic surfaces and removable parts wash with a mild solution of soap and lukewarm water with a little baking soda Rinse and dry thoroughly Avoid getting water on lights controllers fan motors and unfinished wood wine rack faces CAUTION Do not use abrasive cleaners or cloths on any of the interior or exterior surfaces or removable parts CONDENSER CLEANING WARNING For cleaning the condenser and other routine maintenance shut off electricity to the unit In all instances you should clean the condenser area every three months The condenser is located behind the louvered toe plate To clean the condenser remove the toe plate and use a soft bristle brush and vacuum to remove dust and lint Avoid damaging or crushing the condenser fins or tubing Upon completion re install the louvered toe plate CAUTION Failure to clean the condenser could result in temperature loss or mechanical failure or damages Clean this area every three months 16 6 6 HOW TO LOCK THE KEYBOARD
14. ed toe plate obstructed Has the surrounding ambient temperature changed dramatically Is the interior light ON Controller display is flashing LA e The internal compartment temperature has exceeded the low temperature alarm preset value for over 30 minutes e Check to ensure door is closed e Check for door gasket seal e Has the surrounding ambient temperature changed dramatically Controller display is flashing EE e The controller has a data or memory failure The refrigerated cabinet isn t running e Is there electrical power to the unit e Is your home circuit breaker or fuse on e Is your ON OFF key pad on e Is your condenser area clean 17 PROFESSIONAL GRILLS ANTI TIP BRACKETS Figure 2 TWO DRAWER ANTI TIP LAYOUT WARNING Unit may tip forward when loaded racks shelves are pulled to open position To provide a stable Bracket locations 3 8 TN Anti Tip n BP 9 32 Bracket M 22 1432 f Front of Unit installation the unit must be secured in place with the anti tip brackets provided with the unit A set of metal anti tip brackets are supplied with the unit The anti tip brackets when properly installed should secure the rear legs and prevent the unit from tipping forward Some installation sites may require modification to provide a secure surface for attaching the brackets Void area in cabinetry for Unit A Measurment B Measurement
15. er Loading Product IMPORTANT NOTE Before storing perishables allow unit to run for a minimum of 24 hours to allow temperature stabilization after start up When loading items into unit do not block internal louvers and fan guard openings or performance will be decreased Temperature Control Panel The controller is located inside of the unit The display will read OFF when unit off and will show temperature when unit is on IMPORTANT NOTE the led display is reading actual air temperature not product temperature Under these conditions an air temperature swing does not change the actual product temperature Product temperature remains at a very stable temperature within a 6 swing 12
16. ever be obstructed to achieve maximum performance The single door unit comes standard with black vinyl coated adjustable full extention pullout shelves Adjusting Full Extention Shelving 1 Pull the shelf out to its furthest position Locate the tabs in the middle of both extenders Figure 4 Lift on tab up while pushing the opposite tab down and pull shelf out 2 Repositon each bracket separately Grasp the middle of the bracket pull the front end up and out then forward to remove Figure 5 3 Place bracket at the desired postion Push the rear hook into the rear key slot Set front bracket on the wall hook 4 Repeat for other bracket s 5 Push extenders completely into the unit Align the shelf grooves with the extenders an slide completely into the unit Lift one tab up while pushing the aad opposite tab down and pull shelf out Figure 4 Sliding Shelf Extender Tabs To remove brackets remove shelf lift fron of bracket to disengage RJ the front key slot and pull forward to disengage the rear key slot Figure 5 Sliding Shelf Mounting Brackets PROFESSIONAL GRILLS 9 1 HOW TO SEE THE MIN TEMPERATURE 1 Press and release the key 2 he Lo message will be displayed followed by the minimum temperature recorded 3 By pressing the key again or by waiting 5s the normal display will be restored 9 2 HOW TO SEE THE MAX TEMPERATURE 1 Press and release the key 2 The Hr message
17. ient installation operation and care of your Lynx unit DANGER Indicates a hazard that will result in serious injury or death if precautions are not followed WARNING Indicates a hazard may cause Serious injury or death if precautions are not followed CAUTION Indicates a hazard where minor injury or product damage may occur if you do not follow instructions Once the unit is completely installed we suggest you keep this manual and purchasing documentation in a safe place for future reference Should problems occur refer to the troubleshooting section of this manual The information will help you quickly identify a problem and get it remedied In the event you require assistance please contact Lynx Customer Service PLEASE RECORD YOUR MODEL S INFORMATION Whenever you call to request information or service you will need to know your model number and serial number You can find this information on the serial and identification plate located on the inside ceiling of your unit and on the warranty registration card WARRANTY REGISTRATION CARD The package containing this manual also includes your warranty information Warranty coverage begins on the date your Lynx unit was originally purchased IMPORTANT NOTE Take a moment to read through the included warranty statement and complete Registration as soon as possible to validate the registration date An alternative method of completing the Warranty Registration ca
18. iod of four years following the regular one year warranty period This plan applies to the compressor only installed within the United States and Canada TERMS All service provided by Lynx under the above warranty must be performed by authorized Lynx service representatives unless otherwise specified by Lynx Service will be provided in the home during normal business hours This warranty applies only to products installed for normal residential use it does not include adjusting the controls door reversal light bulb or cleaning the condenser This warranty is extended only to the original purchaser of the Lynx product The above warranty does not apply if e Failure of product was due to transportation e Product was improperly installed misused abused operating with low voltage wiring not conforming electrical codes improperly maintained or modified e The original Bill of Sale delivery date or serial number cannot be verified e Defective parts are not returned for inspection if so required by the Lynx To receive parts and or service and the name of the nearest Lynx authorized service representative contact Lynx Professional Grills Technical Service Department via the WEB at www Lynxgrills com or write to Lynx Professional Grills Customer Service Department 5695 Rickenbacker Road Commerce CA 90040 call 888 289 5969 or e mail us at service Lynxgrills com Warranty is in lieu of any other warranties expressed or im
19. lockwise to lower the unit 4 Slide the unit into position making sure the rear cabinet leveling legs slide under the anti tip devices Push the unit into the opening until the bottom front edge of the cabinet is flush with the surrounding cabinetry or the leveling legs are tight with the anti tip devices IMPORTANT NOTE The rear cabinet leveling legs must be engaged under the anti tip brackets 5 Check door openings and ensure unit is level CHECKING PRODUCT TEMPERATURE To accurately check the temperature of the product stored in a refrigerated compartment insert an accurate thermometer into a plastic non breakable bottle partially filled with water Tighten the bottle cap securely Place the bottle in the desired area for 24 hours Refrain from opening the unit during the testing period After 24 hours check the temperature of the water Adjust the control settings if necessary and re test Your Lynx units are pre set in order to achieve the recommended temperature range when installed in a 70 F ambient room temperature Factors which affect the internal temperatures of the refrigerated cabinet include e Temperature setting e Room temperature where installed e Number of times the door is opened and closed e Length of times the door is opened and closed Length of times the door is left open Style of door installed Door gasket sealing and condition Amount of time the internal light is illuminated e Inst
20. n be accomplished online at www Lynxgrills com If you do not return your Warranty Registration Lynx will use the date of sale as the first date of warranty for your new Refrigerated Cabinet You can also provide proof of purchase to Lynx customer service at 888 289 5969 Please record the purchase date of your Lynx product and your dealer s name address and telephone number MODELNUMBER SERIAL NUMBER PURCHASE DATE DEALER NAME amp ADDRESS DEALER TELEPHONE PROFESSIONAL GRILLS 22 PROFESSIONAL GRILLS 21 PROFESSIONAL GRILLS TABLE OF CONTENTS INTRODUCTHON Peper teeter re ere ere ere ere eee err ere eT E re eee PLEASE RECORD YOUR MODELS INFORMATION comision sico WARRANTY REGISTRATION CARD xx TABLE OFCONITENT TTT GENERAL PREGAUTIONS TTT INSTALLATION INSTRUCTIONS TT FIGURE 1 SPECIFICATION DRAWING x x x x x e aisceaceensd lt eaectereesaentactcssuesetesmerd tens PREPARING THE OPA TTT PREPARING ELECTRICAL CONNECTIONS xxe UNPACKING AND eT Le AN TI TIP OVER INSTALLATION TTT EAC R oane A E A EE EE E TOE PLATE INSTALELATI N ac secs ae cease E E E FIGURES TOE PLATE INSTALLATION TTT Sigla CAP e A PIOREO AA nn A A DOOR RINGE REVER AC ssion na EnEn EE E E E pido gate ase teseseae OPERATION a aia ctu ees cee cea OA E A EEE EE E INTERIOR CIORI a ess RES eee O EERE EEN EE eee eee LOADING PRODUC ieee renner ere tye rte rere r E aeai TEMPERATURE CONTROLLER eeepc eee eset aes coe ie eee
21. oad Commerce CA 90040 call 888 289 5969 or e mail us at www Lynxgrills com 18 PROFESSIONAL GRILLS TROUBLESHOOTING BEFORE CALLING FOR SERVICE If the unit appears to be malfunctioning read through NORMAL OPERATION first If the problem persists check the TROUBLESHOOTING GUIDE Locate the problem in the guide and refer to the cause and its remedy before calling for service The problem could be something which can be solved without a service call GENERAL TROUBLESHOOTING DANGER ELECTROCUTION HAZARD NEVER ATTEMPT TO REPAIR OR PERFORM MAINTENANCE ON THE UNIT UNTIL THE MAIN ELECTRICAL POWER HAS BEEN DISCONNECTED No interior light e ls the bulb loose e ls the bulb burned out Light stays on when door is closed e Manual ON OFF light switch is turned ON e Is the door switch making contact with the door Noise during operation e Certain sounds are normal Soft sounds from the compressor fan motor and valves will be heard e During freezer defrost crackling is normal Controller display is flashing P1 e There is a thermostat probe failure Controller display is flashing P2 e There is an evaporator probe failure Controller display is flashing HA e The internal compartment temperature has exceeded the high temperature alarm preset value for over 30 minutes Check to ensure door is closed Check for door gasket seal Did you just install warm product Is the condenser clean Is the louver
22. ottom Door Hinges and Push Plunger using screws removed in Step 6 Step 11 Place Lower V Block into Lower Cabinet Hinge with notch parrallel jo cabinet Parrallel Top View 11 Step 12 UT the Door Assembly and insert top pin into bearing Then move door toward cabinet and align V Blocks Step 19 4 Insert and tighten Lower Hinge Pin to complete assembly OPERATION The Lynx L24BF comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with an adjustable digital temperature controller and LED display The refrigerator is a frost free model meaning the evaporator cooling coil automatically defrosts on demand at predetermined intervals The controller also has a manual defrost soft button on the front panel signified by a melting snowflake If depressed it will automatically put the system into a defrost cycle Interior light The unit is equipped with an interior light that is illuminated when the door is opened The cabinet also comes standard with a manual light switch located next to the light Always ensure that the manual switch is in the off position before closing the door If manual light switch is left on for an extended period of time it may increase the cabinet temperature especially at the top and cause the refrigeration system to run long
23. plied and all other obligations or liabilities related to the sale or use of its regrigeration products including but not limited to any implied warranty of merchantability or fitness for a particular purpose provided however that to the extent required by law implied warranties are included but do not extend beyond the duration of the express warranty first set above Lynx s sole liability and your exclusive remedy under this warranty are set forth in the initial paragraph above Lynx shall have no liability whatsoever for any incidental consequential or special damages arising from the sale use or installation of the product or from any other causes whatsoever whether based on warranty expressed or implied or otherwise based on contract tort or any other theory of liability Some states do not allow limitations on how long an implied warranty lasts or the exclusions of or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state 19 PROFESSIONAL GRILLS 50 area in which p electrical outlet must be located mr 131 16 distance same on both sides of cabinet 4 2 min clearance to side wall on corner installation i L 98 min door swing or pull out shelf clearance 24 2 22 door swing clearance 35 1 16 Max 34 5 16 Min Figure 1 Dimensions
Download Pdf Manuals
Related Search