Wireless Keypad
Contents
1. code or old entry code to your new code but the keypad must be learnt successfully with control board of sliding gate operator before you try to change the entry code Make sure the control board of the opener is power on and in standby mode PWR LED is on and REM LED is off gate is stop Step 1 Press and release PIN button on the keypad LM172 and then enter the 6 digits default or old entry code factory default entry code is 888888 Step 2 Press and release PIN button on the keypad LM172 REM LED of the control board is ON waiting for user to input the new entry code Step 3 Enter your 6 digits new entry code and press PIN button to store it The entry code has been updat ed successfully while REM LED flashes for 2 seconds on control board NOTE Every step for pressing button during program must be finished within 1 second to ensure success full program How to change the battery of Keypad LM172 Step 1 Remove the black cover with slotted screwdriver then you will find 2 screws Step 2 Remove the front panel with screwdriver uncover the battery holder and replace the battery Step 3 Restore the back cover and front cover with cross screwdriver Ref to the Figure 1 6 Fig 6 The wireless keypad LM172 should be installed outside of the property Pull to Open and on the same side of the driveway where the control box is installed The distance between the keypad and control box should not ex2. you may change the factory default entry code or old entry code to your new code but the keypad must be learnt successfully with control board of sliding gate operator before you try to change the entry code Make sure the control board of opener is power on and in standby mode PWR LED is on and REM LED is off gate is stop Step 1 Press and release PIN button on the keypad LM172 and then enter the 6 digits default or old entry code factory default entry code is 888888 Step 2 Press and release PIN button on the keypad LM172 REM LED of the control board is ON waiting for user to input the new entry code Step 3 Enter your 6 digits new entry code and press PIN button to store it The entry code has been updat ed successfullu while REM LED flashed for 2 seconds on control board NOTE Every step for pressing button during program must be finished within 1 second to ensure success full program Use For SCG SFG Series Sliding Gate Learn Transmitter code PO Make sure the control board of opener is power on and in standby mode PWR LED is on and REM LED is off gate is stop PWR LED o Step 1 Press and release Learn button of WR the control board and then REM LED will be on Step 2 Press the OK button once on the keypad LM172 to learn the transimitter code If the keypad has been learnt successfully the REM LED will flash for 2 seconds and then back to off Now you ca
3. ALEKO Wireless Keypad Model LM172 Programming and Operating Instruction Manual re NOTE Please read this manual carefully before install and use www WholesaleGateOpener com Thank you for purchasing the Wireless Keypad LM172 The keypad has been integrated a LED backlight key feature It will bring you great pleasure and convenience while you use it to operate LM MK series Swing Gate Opener and DSC R or SFG SCG series Sliding Gate Opener Be sure to read the manual carefully and completely before you permanently mounting the keypad please program the keypad and test its range Keypad Description K E 1S J vvv wifiOCel i Prinses narrans I i WILT S4 Battery Holder LED backlight key Use 3xAAA 1 5V battery NOTE 3xAAA 1 5V battery is required to power the keypad Use For LM MK Series Swing Gate Opener Learn Transmitter code Make sure the control board of the opener is power on and in standby mode LED flashes Step 1 Press and release LEARN button and then LED will display Ln Step 2 Press OK button on the Keypad LM172 once to learn the keypad Once the keypad has been learnt successfully LED of the control board will flashes Ln for 2 seconds and then flashes again Now you can use the factory default password 888888 to operate the gate opener Refer to the chapter HOW TO OPERATE LM M
4. K SERIES SWING GATE OPENER in manual e __ e m ajs aja ajma Cjo O Control Board of LM MK Series Swing Gate Opener NOTE Once LED displays EA Ln you must press the OK button on the wireless keypad within 1 2 seconds to learn the transmitter code or you may have to start over How to Operate LM MK Series Swing Gate Opener Once the keypad LM172 has been learnt successfully you can use default code to operate the gate 1 When the gate stops in some positon and the opener is in standby mode you can make it to move via the following steps Step 1 Press and release PIN button on the keypad LM172 and then enter the 6 digits entry code factory default entry code is 888888 Step 2 Press the OK button within 1 second after step 1 to move the gate 2 You can press the OK button at anytime to stop the moving gate Entry code is not needed NOTE The beeper of the keypad LM172 will beep at the press of any key When you enter the entry code each button should be pressed within 1 second If an error has occurred the beep will sound for 2 seconds before returning to normal operation Please try again NOTE If the Keypad LM172 is installed outside of the gate to open the gate and no Keypad is installed inside of the gate we strongly recommend you set the auto close function in circuit board in control box Refer to Installation and Operation Manual page 22 Programming the n
5. LED Learn Button and then back to off Now you can use the factory defaut code to operate the gate Refer to the chapter HOW TO OPERATE DSR DSC 1000 600 DSR400 in manual NOTE The OK button should be pressed within 1 second after step 1 or you may have to start over How to Operate DSR DSC Series Sliding Gate Opener Once the keypad LM172 has been learnt successfully you can use default code to operate the gate 1 When the gate stops in some positon and the operator is in standby mode you can make it to move via the following steps Step 1 Press and release PIN button on the wirelesskeypad and then enter the 6 digits entry code factory defaut entry code is 888888 Step 2 Press the OK button within 1 second after step 1 to move the gate 2 You can press the OK button at anytime to stop the moving gate Entry code is not needed NOTE The beeper of the keypad LM172 will beep at the press of any key When you enter the entry code each button should be pressed within 1 second If an error has occurred the beep will sound for 2 seconds before returning to normal operation Please try again NOTE If the Keypad LM172 is installed outside of the gate to open the gate and no Keypad is installed inside of the gate we strongly recommend you set the auto close function in circuit board in control box Refer to Installation and Operation Manual page 15 Programming the new entry code For safety reason
6. ceed 5 meters If the keypad is installed on the opposite side of the driveway the keypad operation maybe interfered by the electromagnetic waves from a passing vehicle Refer to the Fig 7 000 a JILM172 Control Box Fig 7 NOTE We suggest you use the wired keypad LM106 LM106M take place of the wireless keypad for installation in the locations where the frequency interference is restricted nearby airport for ex ample or the control box is installed far way from the gate operator father than 30 or 10 meter installation of the keypad Note The mounting holes of the keypad has not been penetrated you should use one tool with sharp head to penetrate them Install the keypad by the following figure penetrate the mounting holes before you install the keypad How to increase the control distance of keypad The designed remote range of the Keypad is 5 10 meters If you find that the Keypad is not sensitive enough in on site installation we suggest you enhance the remote range by the following method Step 1 Open the control box the black color antenna can be found in the side of PCB Step 2 Draw the antenna straight and pull it through the cable hole in the bottom of the control box Ref to the figure 8 9 and 10 Trouble Shooting 1 Fail to learn the transimitter code a Check if the battery is exhausted b Re learn the keypad anear the control board c Once the control board is ready to
7. ew entry code For safety reason you may change the factory default entry code or old entry code to your new code but the keypad must be learnt successfully with control board of swing gate opener before you try to change the entry code Make sure the control board of the opener is power on and in standby mode LED flashes el Step 1 Press and release PIN button on the keypad LM172 and then enter the 6 digits default or old entry code factory default entry code is 888888 Step 2 Press and release PIN button on the keypad LM172 CH will display on the LED of the control board Step 3 Enter your 6 digits new entry code and press PIN button to store it The entry code has been updat ed successfully while CH flashes for 2 seconds on LED of the control board NOTE Every step for pressing button during program must be finished within 1 second to ensure success full program Use For DSR DSC Series Sliding Gate Opener Learn Transmitter code Control Board of DSR DSC 1000 600 Make sure the control board of opener is power on and in standby mode PWR LED is on and REM LED is off gate is stop Step 1 Press and release Learn button of the control board and then REM LED will be on Step 2 Press the OK button once on the keypad LM172 to learn the transimitter code If the keypad has been learnt successfully the REM LED will flash for 2 seconds REM LED PWR
8. learn the keypad press the OK button within 1 second 2 Fail to operate the gate with keypad a Check if the battery is exhausted b The distance is too far to use the keypad Refer to the chapter How to increase the control distance of keypad 3 Forget your own entry code Re learn the keypad according to the manual The entry code would be 888888 if the keypad has been learnt successfully sales WholesaleGateOpener com www WholesaleGateOpener com 2005 2012 LockMaster All Rights Reserved
9. n use the factory defaut code to operate the gate Refer to the chapter HOW TO OPERATE SCG SFG SERIES SLIDING GATE OPENER in manual NOTE The OK button should be pressed within 1 second after step 1 or you may have to start over How to Operate SCG SFG Sliding Gate Opener Once the keypad LM172 has been learnt successfully you can use default code to operate the gate 1 When the gate stops in some positon and the operator is in standby mode you can make it to move via the following steps Step 1 Press and release PIN button on the wirelesskeypad and then enter the 6 digits entry code factory defaut entry code is 888888 Step 2 Press the OK button within 1 second after step 1 to move the gate 2 You can press the OK button at anytime to stop the moving gate Entry code is not needed NOTE The beeper of the keypad LM172 will beep at the press of any key When you enter the entry code each button should be pressed within 1 second If an error has occurred the beep will sound for 2 seconds before returning to normal operation Please try again NOTE If the Keypad LM172 is installed outside of the gate to open the gate and no Keypad is installed inside of the gate we strongly recommend you set the auto close function in circuit board in control box Refer to Installation and Operation Manual page 14 Programming the new entry code For safety reason you may change the factory default entry
Download Pdf Manuals
Related Search